When dumping the END and NVP tables ("info pic" from the HMP) on the
P10 model, we're likely to be flooded with error messages such as:
XIVE[0] - VST: invalid NVPT entry f33800 !?
The error is printed when finding an empty VSD in an indirect
table (thus END and NVP tables with skiboot), which is going to happen
when dumping the xive state. So let's tune down those messages. They
can be re-enabled easily with a macro if needed.
Those errors were already hidden on xive/P9, for the same reason.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230531150537.369350-1-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The Thread Interrupt Management Area (TIMA) can be accessed through 4
ports, targeted by the address. The base address of a TIMA
is using port 0 and the other ports are 0x80 apart. Using one port or
another can be useful to balance the load on the snoop buses. With
skiboot and linux, we currently use port 0, but as it tends to be
busy, another hypervisor is using port 1 for TIMA access.
The port address bits fall in between the special op indication
bits (the 2 MSBs) and the register offset bits (the 6 LSBs). They are
"don't care" for the hardware when processing a TIMA operation. This
patch filters out those port address bits so that a TIMA operation can
be triggered using any port.
It is also true for indirect access (through the IC BAR) and it's
actually nothing new, it was already the case on P9. Which helps here,
as the TIMA handling code is common between P9 (xive) and P10 (xive2).
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-6-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
TIMA addresses are somewhat special and are split in several bit
fields with different meanings. This patch describes it and introduce
macros to more easily access the various fields.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-5-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Fix what was probably a silly mistake and allow to write the Physical
Thread enable registers 0 and 1. Skiboot prefers to use the ENx_SET
variant so it went unnoticed, but there's no reason to discard a write
to the full register, it is Read-Write.
Fixes: da71b7e3ed ("ppc/pnv: Add a XIVE2 controller to the POWER10 chip")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-4-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add basic read/write support for the ESB cache configuration register
on P10. We don't model the ESB cache in qemu so reading/writing the
register won't do anything, but it avoids logging a guest error when
skiboot configures it:
qemu-system-ppc64 -machine powernv10 ... -d guest_errors
...
XIVE[0] - VC: invalid read @240
XIVE[0] - VC: invalid write @240
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-3-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add basic read/write support for the TCTXT Config register on P10. qemu
doesn't do anything with it yet, but it avoids logging a guest error
when skiboot configures the fused-core state:
qemu-system-ppc64 -machine powernv10 ... -d guest_errors
...
[ 0.131670000,5] XIVE: [ IC 00 ] Initializing XIVE block ID 0...
XIVE[0] - TCTXT: invalid read @140
XIVE[0] - TCTXT: invalid write @140
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230601121331.487207-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The 9p protocol does not specifically define how server shall behave when
client tries to open a special file, however from security POV it does
make sense for 9p server to prohibit opening any special file on host side
in general. A sane Linux 9p client for instance would never attempt to
open a special file on host side, it would always handle those exclusively
on its guest side. A malicious client however could potentially escape
from the exported 9p tree by creating and opening a device file on host
side.
With QEMU this could only be exploited in the following unsafe setups:
- Running QEMU binary as root AND 9p 'local' fs driver AND 'passthrough'
security model.
or
- Using 9p 'proxy' fs driver (which is running its helper daemon as
root).
These setups were already discouraged for safety reasons before,
however for obvious reasons we are now tightening behaviour on this.
Fixes: CVE-2023-2861
Reported-by: Yanwu Shen <ywsPlz@gmail.com>
Reported-by: Jietao Xiao <shawtao1125@gmail.com>
Reported-by: Jinku Li <jkli@xidian.edu.cn>
Reported-by: Wenbo Shen <shenwenbo@zju.edu.cn>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <E1q6w7r-0000Q0-NM@lizzy.crudebyte.com>
Clarify the behavior of TYPE_VFU_OBJECT when TYPE_REMOTE_MACHINE enables
the auto-shutdown property. Also, add notes to VFU_OBJECT_ERROR.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
During the last patches, TYPE_PIIX3_XEN_DEVICE turned into a clone of
TYPE_PIIX3_DEVICE. Remove this redundancy.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-7-shentey@gmail.com>
Message-Id: <20230403074124.3925-8-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
The previous patch unified handling of piix3_write_config() accross the
PIIX3 device models which allows for assigning k->config_write once in the
base class.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-6-shentey@gmail.com>
Message-Id: <20230403074124.3925-7-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Subscribe to pci_bus_fire_intx_routing_notifier() instead which allows for
having a common piix3_write_config() for the PIIX3 device models.
While at it, move the subscription into machine code to facilitate resolving
TYPE_PIIX3_XEN_DEVICE.
In a possible future followup, pci_bus_fire_intx_routing_notifier() could
be adjusted in such a way that subscribing to it doesn't require
knowledge of the device firing it.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-5-shentey@gmail.com>
Message-Id: <20230403074124.3925-6-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_intx_set_irq() doesn't depend on PIIX3State. In order to resolve
TYPE_PIIX3_XEN_DEVICE and in order to make Xen agnostic about the
precise south bridge being used, set up Xen's PCI IRQ handling of PIIX3
in the board.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-4-shentey@gmail.com>
Message-Id: <20230403074124.3925-5-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
This is a preparational patch for the next one to make the following
more obvious:
First, pci_bus_irqs() is now called twice in case of Xen where the
second call overrides the pci_set_irq_fn with the Xen variant.
Second, pci_bus_set_route_irq_fn() is now also called in Xen mode.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-3-shentey@gmail.com>
Message-Id: <20230403074124.3925-4-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
When calling pci_bus_irqs() multiple times on the same object without calling
pci_bus_irqs_cleanup() in between PCIBus::irq_count[] is currently leaked.
Let's fix this because Xen will do just that in a few commits, and because
calling pci_bus_irqs_cleanup() in between seems fragile and cumbersome.
Note that pci_bus_irqs_cleanup() now has to NULL irq_count such that
pci_bus_irqs() doesn't do a double free.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230403074124.3925-3-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
xen_piix3_set_irq() isn't PIIX specific: PIIX is a single PCI device
while xen_piix3_set_irq() maps multiple PCI devices to their respective
IRQs, which is board-specific. Rename xen_piix3_set_irq() to communicate
this.
Also rename XEN_PIIX_NUM_PIRQS to XEN_IOAPIC_NUM_PIRQS since the Xen's
IOAPIC rather than PIIX has this many interrupt routes.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Tested-by: Chuck Zmudzinski <brchuckz@aol.com>
Message-Id: <20230312120221.99183-2-shentey@gmail.com>
Message-Id: <20230403074124.3925-2-shentey@gmail.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Coverity points out that if (!s && !s->impl) isn't really what we intended
to do here. CID 1508131.
Fixes: 0324751272 ("hw/xen: Add emulated implementation of XenStore operations")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20230412185102.441523-6-dwmw2@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
In restructuring to allow for internal emulation of Xen functionality,
I broke compatibility for Xen 4.6 and earlier. Fix this by explicitly
removing support for anything older than 4.7.1, which is also ancient
but it does still build, and the compatibility support for it is fairly
unintrusive.
Fixes: 15e283c5b6 ("hw/xen: Add foreignmem operations to allow redirection to internal emulation")
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230412185102.441523-4-dwmw2@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
There was a superfluous allocation of the XS handle, leading to it
being leaked on both the error path and the success path (where it gets
allocated again).
Spotted by Coverity (CID 1508098).
Fixes: ba2a92db1f ("hw/xen: Add xenstore operations to allow redirection to internal emulation")
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230412185102.441523-3-dwmw2@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
I initially put the basic platform init (overlay pages, grant tables,
event channels) into mc->kvm_type because that was the earliest place
that could sensibly test for xen_mode==XEN_EMULATE.
The intent was to do this early enough that we could then initialise the
XenBus and other parts which would have depended on them, from a generic
location for both Xen and KVM/Xen in the PC-specific code, as seen in
https://lore.kernel.org/qemu-devel/20230116221919.1124201-16-dwmw2@infradead.org/
However, then the Xen on Arm patches came along, and *they* wanted to
do the XenBus init from a 'generic' Xen-specific location instead:
https://lore.kernel.org/qemu-devel/20230210222729.957168-4-sstabellini@kernel.org/
Since there's no generic location that covers all three, I conceded to
do it for XEN_EMULATE mode in pc_basic_devices_init().
And now there's absolutely no point in having some of the platform init
done from pc_machine_kvm_type(); we can move it all up to live in a
single place in pc_basic_devices_init(). This has the added benefit that
we can drop the separate xen_evtchn_connect_gsis() function completely,
and pass just the system GSIs in directly to xen_evtchn_create().
While I'm at it, it does no harm to explicitly pass in the *number* of
said GSIs, because it does make me twitch a bit to pass an array of
impicit size. During the lifetime of the KVM/Xen patchset, that had
already changed (albeit just cosmetically) from GSI_NUM_PINS to
IOAPIC_NUM_PINS.
And document a bit better that this is for the *output* GSI for raising
CPU0's events when the per-CPU vector isn't available. The fact that
we create a whole set of them and then only waggle the one we're told
to, instead of having a single output and only *connecting* it to the
GSI that it should be connected to, is still non-intuitive for me.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20230412185102.441523-2-dwmw2@infradead.org>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Only a few important registers are added, especially the SRAM_VER
register.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
R40 has two ethernet controllers named as emac and gmac. The emac is
compatibled with A10, and the GMAC is compatibled with H3.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A64's sd register was similar to H3, and it introduced a new register
named SAMP_DL_REG location at 0x144. The dma descriptor buffer size of
mmc2 is only 8K and the other mmc controllers has 64K.
Also fix allwinner-r40's mmc controller type.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Types of memory that the SDRAM controller supports are DDR2/DDR3
and capacities of up to 2GiB. This commit adds emulation support
of the Allwinner R40 SDRAM controller.
This driver only support 256M, 512M and 1024M memory now.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds minimal support for AXP-221 PMU and connect it to
bananapi M2U board.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TWI(i2c) is designed to be used as an interface between CPU host and the
serial 2-Wire bus. It can support all standard 2-Wire transfer, can be
operated in standard mode(100kbit/s) or fast-mode, supporting data rate
up to 400kbit/s.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
R40 has eight UARTs, support both 16450 and 16550 compatible modes.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CCU provides the registers to program the PLLs and the controls
most of the clock generation, division, distribution, synchronization
and gating.
This commit adds support for the Clock Control Unit which emulates
a simple read/write register interface.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allwinner R40 (sun8i) SoC features a Quad-Core Cortex-A7 ARM CPU,
and a Mali400 MP2 GPU from ARM. It's also known as the Allwinner T3
for In-Car Entertainment usage, A40i and A40pro are variants that
differ in applicable temperatures range (industrial and military).
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect CANFD0 and CANFD1 on the Versal-virt machine and update xlnx-versal-virt
document with CANFD command line examples.
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx Versal CANFD controller is developed based on SocketCAN, QEMU CAN bus
implementation. Bus connection and socketCAN connection for each CAN module
can be set through command lines.
Signed-off-by: Vikram Garhwal <vikram.garhwal@amd.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mechanical change running Coccinelle spatch with content
generated from the qom-cast-macro-clean-cocci-gen.py added
in the previous commit.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230601093452.38972-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Booting a Linux kernel with the malta machine is currently broken
on big endian hosts. The cpu_to_gt32 macro wants to byteswap a value
for little endian targets only, but uses the wrong way to do this:
cpu_to_[lb]e32 works the other way round on big endian hosts! Fix
it by using the same ways on both, big and little endian hosts.
Fixes: 0c8427baf0 ("hw/mips/malta: Use bootloader helper to set BAR registers")
Cc: qemu-stable@nongnu.org
Message-Id: <20230330152613.232082-1-thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The attribute isn't used since commit 5c9736789b
"i82378: Cleanup implementation".
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20230523195608.125820-4-shentey@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The function is unused since commit
bdad3654d3 ('hw/arm/nseries: Remove
invalid/unnecessary n8x0_uart_setup()').
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230523195608.125820-3-shentey@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Both TYPE_KVM_I8254 and TYPE_I8254 have their own but same implementation of
the "iobase" property. The storage for the property already resides in
PITCommonState, so also move the property definition there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230523195608.125820-2-shentey@gmail.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
As per "Loongson 3A5000/3B5000 Processor Reference Manual",
Loongson 3A5000's IPI implementation have 4 mailboxes per
core.
However, in 78464f023b ("hw/loongarch/virt: Modify ipi as
percpu device"), the number of IPI mailboxes was reduced to
one, which mismatches actual hardware.
It won't affect LoongArch based system as LoongArch boot code
only uses the first mailbox, however MIPS based Loongson boot
code uses all 4 mailboxes.
Fixes Coverity CID: 1512452, 1512453
Fixes: 78464f023b ("hw/loongarch/virt: Modify ipi as percpu device")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20230521102307.87081-2-jiaxun.yang@flygoat.com>
Signed-off-by: Song Gao <gaosong@loongson.cn>
As shown in the previous commit, qemu_strtosz_MiB sometimes leaves the
result value untouched (we have to audit further to learn that in that
case, the QAPI generator says that visit_type_NumaOptions() will have
zero-initialized it), and sometimes leaves it with the value of a
partial parse before -EINVAL occurs because of trailing garbage.
Rather than blindly treating any string the user may throw at us as
valid, we should check for parse failures.
Fixes: cc001888 ("numa: fixup parsed NumaNodeOptions earlier", v2.11.0)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Message-Id: <20230522190441.64278-14-eblake@redhat.com>
No need to pass zeros as we have helpers that do that for us.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230526165401.574474-11-alex.bennee@linaro.org
Message-Id: <20230524133952.3971948-10-alex.bennee@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Now we no longer have any events that are for vcpus we can start
excising the code from the trace control. As the vcpu parameter is
encoded as part of QMP we just stub out the has_vcpu/vcpu parameters
rather than alter the API.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230526165401.574474-8-alex.bennee@linaro.org
Message-Id: <20230524133952.3971948-7-alex.bennee@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
While these are all in helper functions being designated vcpu events
complicates the removal of the dynamic vcpu state code. TCG plugins
allow you to instrument vcpu_[init|exit|idle].
We rename cpu_reset and make it a normal trace point.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20230526165401.574474-3-alex.bennee@linaro.org
Message-Id: <20230524133952.3971948-3-alex.bennee@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Introduce a new API for thread-local blk_io_plug() that does not
traverse the block graph. The goal is to make blk_io_plug() multi-queue
friendly.
Instead of having block drivers track whether or not we're in a plugged
section, provide an API that allows them to defer a function call until
we're unplugged: blk_io_plug_call(fn, opaque). If blk_io_plug_call() is
called multiple times with the same fn/opaque pair, then fn() is only
called once at the end of the function - resulting in batching.
This patch introduces the API and changes blk_io_plug()/blk_io_unplug().
blk_io_plug()/blk_io_unplug() no longer require a BlockBackend argument
because the plug state is now thread-local.
Later patches convert block drivers to blk_io_plug_call() and then we
can finally remove .bdrv_co_io_plug() once all block drivers have been
converted.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 20230530180959.1108766-2-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
- Fix blockdev-create with iothreads
- Remove aio_disable_external() API
-----BEGIN PGP SIGNATURE-----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=yuER
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://repo.or.cz/qemu/kevin into staging
Block layer patches
- Fix blockdev-create with iothreads
- Remove aio_disable_external() API
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmR2JIARHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9brtA/9HVdAdtJxW78J60TE2lTqE9XlqMOEHBZl
# 8GN72trjP2geY/9mVsv/XoFie4ecqFsYjwAWWUuXZwLgAo53jh7oFN7gBH5iGyyD
# +EukYEfjqoykX5BkoK0gbMZZUe5Y4Dr2CNXYw4bNg8kDzj2RLifGA1XhdL3HoiVt
# PHZrhwBR7ddww6gVOnyJrfGL8fMkW/ZNeKRhrTZuSP+63oDOeGTsTumD+YKJzfPs
# p5WlwkuPjcqbO+w32FeVOHVhNI4swkN5svz3fkr8NuflfA7kH6nBQ5wymObbaTLc
# Erx03lrtP1+6nw43V11UnYt6iDMg4EBUQwtzNaKFnk3rMIdjoQYxIM5FTBWL2rYD
# Dg6PhkncXQ1WNWhUaFqpTFLB52XAYsSa4/y2QAGP6nWbqAUAUknQ3exaMvWiq7Z0
# nZeyyhIWvpJIHGCArWRdqqh+zsBdsmUVuPGyZnZgL/cXoJboYiHMyMJSUWE0XxML
# NGrncwxdsBXkVGGwTdHpBT64dcu3ENRgwtraqRLQm+tp5MKNTJB/+Ug2/p1vonHT
# UOoHz//UPskn8sHIyevoHXeu2Ns0uIHzrAXr+7Ay+9UYyIH6a07F4b2BGqkfyi/i
# 8wQsDmJ/idx5C4q1+jS+GuIbpnjIx6nxXwXMqpscUXZmM4Am8OMkiKxQAa1wExGF
# paId+HHwyks=
# =yuER
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 30 May 2023 09:29:52 AM PDT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin: (32 commits)
aio: remove aio_disable_external() API
virtio: do not set is_external=true on host notifiers
virtio-scsi: implement BlockDevOps->drained_begin()
virtio-blk: implement BlockDevOps->drained_begin()
virtio: make it possible to detach host notifier from any thread
block/fuse: do not set is_external=true on FUSE fd
block/export: don't require AioContext lock around blk_exp_ref/unref()
block/export: rewrite vduse-blk drain code
hw/xen: do not set is_external=true on evtchn fds
xen-block: implement BlockDevOps->drained_begin()
block: drain from main loop thread in bdrv_co_yield_to_drain()
block: add blk_in_drain() API
hw/xen: do not use aio_set_fd_handler(is_external=true) in xen_xenstore
block/export: stop using is_external in vhost-user-blk server
block/export: wait for vhost-user-blk requests when draining
util/vhost-user-server: rename refcount to in_flight counter
virtio-scsi: stop using aio_disable_external() during unplug
virtio-scsi: avoid race between unplug and transport event
hw/qdev: introduce qdev_is_realized() helper
block-backend: split blk_do_set_aio_context()
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All callers now pass is_external=false to aio_set_fd_handler() and
aio_set_event_notifier(). The aio_disable_external() API that
temporarily disables fd handlers that were registered is_external=true
is therefore dead code.
Remove aio_disable_external(), aio_enable_external(), and the
is_external arguments to aio_set_fd_handler() and
aio_set_event_notifier().
The entire test-fdmon-epoll test is removed because its sole purpose was
testing aio_disable_external().
Parts of this patch were generated using the following coccinelle
(https://coccinelle.lip6.fr/) semantic patch:
@@
expression ctx, fd, is_external, io_read, io_write, io_poll, io_poll_ready, opaque;
@@
- aio_set_fd_handler(ctx, fd, is_external, io_read, io_write, io_poll, io_poll_ready, opaque)
+ aio_set_fd_handler(ctx, fd, io_read, io_write, io_poll, io_poll_ready, opaque)
@@
expression ctx, notifier, is_external, io_read, io_poll, io_poll_ready;
@@
- aio_set_event_notifier(ctx, notifier, is_external, io_read, io_poll, io_poll_ready)
+ aio_set_event_notifier(ctx, notifier, io_read, io_poll, io_poll_ready)
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230516190238.8401-21-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Host notifiers can now use is_external=false since virtio-blk and
virtio-scsi no longer rely on is_external=true for drained sections.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20230516190238.8401-20-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
