Some debug registers can be trapped via MDCR_EL2 bits TDRA, TDOSA,
and TDA, which we implement in the functions access_tdra(),
access_tdosa() and access_tda(). If MDCR_EL2.TDE or HCR_EL2.TGE
are 1, the TDRA, TDOSA and TDA bits should behave as if they were 1.
Implement this by having the access functions check MDCR_EL2.TDE
and HCR_EL2.TGE.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180724115950.17316-3-peter.maydell@linaro.org
If the "trap general exceptions" bit HCR_EL2.TGE is set, we
must mask all virtual interrupts (as per DDI0487C.a D1.14.3).
Implement this in arm_excp_unmasked().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180724115950.17316-2-peter.maydell@linaro.org
Use an int64_t as a return type to restore
the negative check for arm_load_as.
Signed-off-by: Adam Lackorzynski <adam@l4re.org>
Message-id: 20180730173712.GG4987@os.inf.tu-dresden.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for GICv2 virtualization extensions by mapping the necessary
I/O regions and connecting the maintenance IRQ lines.
Declare those additions in the device tree and in the ACPI tables.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-21-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit improve the way the GIC is realized and connected in the
ZynqMP SoC. The security extensions are enabled only if requested in the
machine state. The same goes for the virtualization extensions.
All the GIC to APU CPU(s) IRQ lines are now connected, including FIQ,
vIRQ and vFIQ. The missing CPU to GIC timers IRQ connections are also
added (HYP and SEC timers).
The GIC maintenance IRQs are back-wired to the correct GIC PPIs.
Finally, the MMIO mappings are reworked to take into account the ZynqMP
specifics. The GIC (v)CPU interface is aliased 16 times:
* for the first 0x1000 bytes from 0xf9010000 to 0xf901f000
* for the second 0x1000 bytes from 0xf9020000 to 0xf902f000
Mappings of the virtual interface and virtual CPU interface are mapped
only when virtualization extensions are requested. The
XlnxZynqMPGICRegion struct has been enhanced to be able to catch all
this information.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180727095421.386-20-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some traces to the ARM GIC to catch register accesses (distributor,
(v)cpu interface and virtual interface), and to take into account
virtualization extensions (print `vcpu` instead of `cpu` when needed).
Also add some virtualization extensions specific traces: LR updating
and maintenance IRQ generation.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-19-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the maintenance interrupt generation that is part of the GICv2
virtualization extensions.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-18-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the gic_update_virt() function to update the vCPU interface states
and raise vIRQ and vFIQ as needed. This commit renames gic_update() to
gic_update_internal() and generalizes it to handle both cases, with a
`virt' parameter to track whether we are updating the CPU or vCPU
interfaces.
The main difference between CPU and vCPU is the way we select the best
IRQ. This part has been split into the gic_get_best_(v)irq functions.
For the virt case, the LRs are iterated to find the best candidate.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the read and write functions for the virtual interface of the
virtualization extensions in the GICv2.
One mirror region per CPU is also created, which maps to that specific
CPU id. This is required by the GIC architecture specification.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-16-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the read/write functions to handle accesses to the vCPU interface.
Those accesses are forwarded to the real CPU interface, with the CPU id
being converted to the corresponding vCPU id (vCPU id = CPU id +
GIC_NCPU).
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180727095421.386-15-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_cpu_read() and
gic_cpu_write() functions. Those are the last bits missing to fully
support virtualization extensions in the CPU interface path.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-14-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_deactivate_irq() and
gic_complete_irq() functions.
When the guest writes an invalid vIRQ to V_EOIR or V_DIR, since the
GICv2 specification is not entirely clear here, we adopt the behaviour
observed on real hardware:
* When V_CTRL.EOIMode is false (EOI split is disabled):
- In case of an invalid vIRQ write to V_EOIR:
-> If some bits are set in H_APR, an invalid vIRQ write to V_EOIR
triggers a priority drop, and increments V_HCR.EOICount.
-> If V_APR is already cleared, nothing happen
- An invalid vIRQ write to V_DIR is ignored.
* When V_CTRL.EOIMode is true:
- In case of an invalid vIRQ write to V_EOIR:
-> If some bits are set in H_APR, an invalid vIRQ write to V_EOIR
triggers a priority drop.
-> If V_APR is already cleared, nothing happen
- An invalid vIRQ write to V_DIR increments V_HCR.EOICount.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180727095421.386-13-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_acknowledge_irq()
function. This function changes the state of the highest priority IRQ
from pending to active.
When the current CPU is a vCPU, modifying the state of an IRQ modifies
the corresponding LR entry. However if we clear the pending flag before
setting the active one, we lose track of the LR entry as it becomes
invalid. The next call to gic_get_lr_entry() will fail.
To overcome this issue, we call gic_activate_irq() before
gic_clear_pending(). This does not change the general behaviour of
gic_acknowledge_irq.
We also move the SGI case in gic_clear_pending_sgi() to enhance
code readability as the virtualization extensions support adds a if-else
level.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-12-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in gic_activate_irq() and
gic_drop_prio() and in gic_get_prio_from_apr_bits() called by
gic_drop_prio().
When the current CPU is a vCPU:
- Use GIC_VIRT_MIN_BPR and GIC_VIRT_NR_APRS instead of their non-virt
counterparts,
- the vCPU APR is stored in the virtual interface, in h_apr.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-11-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some helper functions to gic_internal.h to get or change the state
of an IRQ. When the current CPU is not a vCPU, the call is forwarded to
the GIC distributor. Otherwise, it acts on the list register matching
the IRQ in the current CPU virtual interface.
gic_clear_active can have a side effect on the distributor, even in the
vCPU case, when the correponding LR has the HW field set.
Use those functions in the CPU interface code path to prepare for the
vCPU interface implementation.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-10-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An access to the CPU interface is non-secure if the current GIC instance
implements the security extensions, and the memory access is actually
non-secure. Until then, it was checked with tests such as
if (s->security_extn && !attrs.secure) { ... }
in various places of the CPU interface code.
With the implementation of the virtualization extensions, those tests
must be updated to take into account whether we are in a vCPU interface
or not. This is because the exposed vCPU interface does not implement
security extensions.
This commits replaces all those tests with a call to the
gic_cpu_ns_access() function to check if the current access to the CPU
interface is non-secure. This function takes into account whether the
current CPU is a vCPU or not.
Note that this function is used only in the (v)CPU interface code path.
The distributor code path is left unchanged, as the distributor is not
exposed to vCPUs at all.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-9-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some helper macros and functions related to the virtualization
extensions to gic_internal.h.
The GICH_LR_* macros help extracting specific fields of a list register
value. The only tricky one is the priority field as only the MSB are
stored. The value must be shifted accordingly to obtain the correct
priority value.
gic_is_vcpu() and gic_get_vcpu_real_id() help with (v)CPU id manipulation
to abstract the fact that vCPU id are in the range
[ GIC_NCPU; (GIC_NCPU + num_cpu) [.
gic_lr_* and gic_virq_is_valid() help with the list registers.
gic_get_lr_entry() returns the LR entry for a given (vCPU, irq) pair. It
is meant to be used in contexts where we know for sure that the entry
exists, so we assert that entry is actually found, and the caller can
avoid the NULL check on the returned pointer.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-8-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the register definitions for the virtual interface of the GICv2.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-7-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary parts of the virtualization extensions state to the
GIC state. We choose to increase the size of the CPU interfaces state to
add space for the vCPU interfaces (the GIC_NCPU_VCPU macro). This way,
we'll be able to reuse most of the CPU interface code for the vCPUs.
The only exception is the APR value, which is stored in h_apr in the
virtual interface state for vCPUs. This is due to some complications
with the GIC VMState, for which we don't want to break backward
compatibility. APRs being stored in 2D arrays, increasing the second
dimension would lead to some ugly VMState description. To avoid
that, we keep it in h_apr for vCPUs.
The vCPUs are numbered from GIC_NCPU to (GIC_NCPU * 2) - 1. The
`gic_is_vcpu` function help to determine if a given CPU id correspond to
a physical CPU or a virtual one.
For the in-kernel KVM VGIC, since the exposed VGIC does not implement
the virtualization extensions, we report an error if the corresponding
property is set to true.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-6-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a VMSTATE_UINT16_SUB_ARRAY macro to save a uint16_t sub-array in
a VMState.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-5-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions are now only used in arm_gic.c, put them static. Some of
them where only used by the NVIC implementation and are not used
anymore, so remove them.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-4-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement GICD_ISACTIVERn and GICD_ICACTIVERn registers in the GICv2.
Those registers allow to set or clear the active state of an IRQ in the
distributor.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-3-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for the virtualization extensions implementation,
refactor the name of the functions and macros that act on the GIC
distributor to make that fact explicit. It will be useful to
differentiate them from the ones that will act on the virtual
interfaces.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We set up TLB entries in tlb_set_page_with_attrs(), where we have
some logic for determining whether the TLB entry is considered
to be RAM-backed, and thus has a valid addend field. When we
look at the TLB entry in get_page_addr_code(), we use different
logic for determining whether to treat the page as RAM-backed
and use the addend field. This is confusing, and in fact buggy,
because the code in tlb_set_page_with_attrs() correctly decides
that rom_device memory regions not in romd mode are not RAM-backed,
but the code in get_page_addr_code() thinks they are RAM-backed.
This typically results in "Bad ram pointer" assertion if the
guest tries to execute from such a memory region.
Fix this by making get_page_addr_code() just look at the
TLB_MMIO bit in the code_address field of the TLB, which
tlb_set_page_with_attrs() sets if and only if the addend
field is not valid for code execution.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180713150945.12348-1-peter.maydell@linaro.org
Now that we have full support for small regions, including execution,
we can remove the workarounds where we marked all small regions as
non-executable for the M-profile MPU and SAU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180710160013.26559-7-peter.maydell@linaro.org
Now that all the callers can handle get_page_addr_code() returning -1,
remove all the code which tries to handle execution from MMIO regions
or small-MMU-region RAM areas. This will mean that we can correctly
execute from these areas, rather than ending up either aborting QEMU
or delivering an incorrect guest exception.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180710160013.26559-6-peter.maydell@linaro.org
If get_page_addr_code() returns -1, this indicates that there is no RAM
page we can read a full TB from. Instead we must create a TB which
contains a single instruction and which we do not cache, so it is
executed only once.
Since this means we can now have TBs which are not in any page list,
we also need to make tb_phys_invalidate() handle them (by not trying
to remove them from a nonexistent page list).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180710160013.26559-5-peter.maydell@linaro.org
When we support execution from non-RAM MMIO regions, get_page_addr_code()
will return -1 to indicate that there is no RAM at the requested address.
Handle this in tb_check_watchpoint() -- if the exception happened for a
PC which doesn't correspond to RAM then there is no need to invalidate
any TBs, because the one-instruction TB will not have been cached.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180710160013.26559-4-peter.maydell@linaro.org
When we support execution from non-RAM MMIO regions, get_page_addr_code()
will return -1 to indicate that there is no RAM at the requested address.
Handle this in the cpu-exec TB hashtable lookup code, treating it as
"no match found".
Note that the call to get_page_addr_code() in tb_lookup_cmp() needs
no changes -- a return of -1 will already correctly result in the
function returning false.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180710160013.26559-3-peter.maydell@linaro.org
The io_readx() function needs to know whether the load it is
doing is an MMU_DATA_LOAD or an MMU_INST_FETCH, so that it
can pass the right value to the cpu_transaction_failed()
function. Plumb this information through from the softmmu
code.
This is currently not often going to give the wrong answer,
because usually instruction fetches go via get_page_addr_code().
However once we switch over to handling execution from non-RAM by
creating single-insn TBs, the path for an insn fetch to generate
a bus error will be through cpu_ld*_code() and io_readx(),
so without this change we will generate a d-side fault when we
should generate an i-side fault.
We also have to pass the access type via a CPU struct global
down to unassigned_mem_read(), for the benefit of the targets
which still use the cpu_unassigned_access() hook (m68k, mips,
sparc, xtensa).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180710160013.26559-2-peter.maydell@linaro.org
The differences from ARMv7-M NVIC are:
* ARMv6-M only supports up to 32 external interrupts
(configurable feature already). The ICTR is reserved.
* Active Bit Register is reserved.
* ARMv6-M supports 4 priority levels against 256 in ARMv7-M.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Forbid stack alignment change. (CCR)
Reserve FAULTMASK, BASEPRI registers.
Report any fault as a HardFault. Disable MemManage, BusFault and
UsageFault, so they always escalated to HardFault. (SHCSR)
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180718095628.26442-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Handle SCS reserved registers listed in ARMv6-M ARM D3.6.1.
All reserved registers are RAZ/WI. ARM_FEATURE_M_MAIN is used for the
checks, because these registers are reserved in ARMv8-M Baseline too.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MSR handling is the only place where CONTROL.nPRIV is modified.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Message-id: 20180705222622.17139-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With vga=775 on the Linux command line a first boot of the VM running
Linux works fine. After a warm reboot it crashes during Linux boot.
Before that, valgrind points out bad memory write to console
surface. The VGA code is not aware that virtio-gpu got a message
surface scanout when the display is disabled. Let's reset VGA graphic
mode when it is the case, so that a new display surface is created
when doing further VGA operations.
https://bugs.launchpad.net/qemu/+bug/1784900/
Reported-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Message-id: 20180803153235.4134-1-marcandre.lureau@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The data in an mbuf buffer is not necessarily at the start of the
allocated buffer. (For instance m_adj() allows data to be trimmed
from the start by just advancing the pointer and reducing the length.)
This means that the allocated buffer size (m->m_size) and the
amount of space from the m_data pointer to the end of the
buffer (M_ROOM(m)) are not necessarily the same.
Commit 864036e251 tried to change the m_inc() function from
taking the new allocated-buffer-size to taking the new room-size,
but forgot to change the initial "do we already have enough space"
check. This meant that if we were trying to extend a buffer which
had a leading gap between the buffer start and the data, we might
incorrectly decide it didn't need to be extended, and then
overrun the end of the buffer, causing memory corruption and
an eventual crash.
Change the "already big enough?" condition from checking the
argument against m->m_size to checking against M_ROOM().
This only makes a difference for the callsite in m_cat();
the other three callsites all start with a freshly allocated
mbuf from m_get(), which will have m->m_size == M_ROOM(m).
Fixes: 864036e251
Fixes: https://bugs.launchpad.net/qemu/+bug/1785670
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Message-id: 20180807114501.12370-1-peter.maydell@linaro.org
Tested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The instance_init function of the xtensa CPUs creates a memory region,
but does not set an owner, so the memory region is not destroyed
correctly when the CPU object is removed. This can happen when
introspecting the CPU devices, so introspecting the CPU device will
leave a dangling memory region object in the QOM tree. Make sure to
set the right owner here to fix this issue.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-id: 1532005320-17794-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code currently in gicv3_gicd_no_migration_shift_bug_post_load()
that handles migration from older QEMU versions with a particular
bug is misplaced. We need to run this after migration in all cases,
not just the cases where the "arm_gicv3/gicd_no_migration_shift_bug"
subsection is present, so it must go in a post_load hook for the
top level VMSD, not for the subsection. Move it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180806123445.1459-6-peter.maydell@linaro.org
Contrary to the the impression given in docs/devel/migration.rst,
the migration code does not run the pre_load hook for a
subsection unless the subsection appears on the wire, and so
this is not a place where you can set the default value for
state for the "subsection not present" case. Instead this needs
to be done in a pre_load hook for whatever is the parent VMSD
of the subsection.
We got this wrong in two of the subsection definitions in
the GICv3 migration structs; fix this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180806123445.1459-5-peter.maydell@linaro.org
Currently the migration code incorrectly treats a subsection with
no .needed function pointer as if it was the subsection list
terminator -- it is ignored and so is everything after it.
Work around this by giving various M profile vmstate structs
a 'needed' function that always returns true.
We reuse m_needed() for this, since it's always true here.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-4-peter.maydell@linaro.org
Commit 6692aac411 accidentally introduced a second initialization
of the .subsections field of vmstate_gicv3_cpu, instead of adding
the new subsection to the existing list. The effect of this was
probably that migration of GICv3 with virtualization enabled was
broken (or alternatively that migration of ICC_SRE_EL1 was broken,
depending on which of the two initializers the compiler used).
Combine the two into a single list.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-3-peter.maydell@linaro.org
Currently the migration code incorrectly treats a subsection with
no .needed function pointer as if it was the subsection list
terminator -- it is ignored and so is everything after it.
Work around this by giving vmstate_gicv3_gicd_no_migration_shift_bug
a 'needed' function that always returns true.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-2-peter.maydell@linaro.org
If we do not opimize away dup_vec, we must mark its output as changed.
Fixes: 170ba88f45
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20180805233258.31892-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 848a1cc1e (hw/acpi-build: build SRAT memory affinity structures for DIMM devices)
broke the first dimm hotplug in following cases:
1: there is no coldplugged dimm in the last numa node
but there is a coldplugged dimm in another node
-m 4096,slots=4,maxmem=32G \
-object memory-backend-ram,id=m0,size=2G \
-device pc-dimm,memdev=m0,node=0 \
-numa node,nodeid=0 \
-numa node,nodeid=1
2: if order of dimms on CLI is:
1st plugged dimm in node1
2nd plugged dimm in node0
-m 4096,slots=4,maxmem=32G \
-object memory-backend-ram,size=2G,id=m0 \
-device pc-dimm,memdev=m0,node=1 \
-object memory-backend-ram,id=m1,size=2G \
-device pc-dimm,memdev=m1,node=0 \
-numa node,nodeid=0 \
-numa node,nodeid=1
(qemu) object_add memory-backend-ram,id=m2,size=1G
(qemu) device_add pc-dimm,memdev=m2,node=0
the first DIMM hotplug to any node except the last one
fails (Windows is unable to online it).
Length reduction of stub hotplug memory SRAT entry,
fixes issue for some reason.
RHBZ: 1609234
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now, QEmu adds a new check for memory-less NUMA nodes in build_srat().
It effects the ACPI test.
So, Update ACPI tables test blobs.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
