ASID currently has uint8_t type which is too small since some processors
support more than 8 bits ASID. Therefore change its type to uint16_t.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
The MAAR register is a read/write register included in Release 5
of the architecture that defines the accessibility attributes of
physical address regions. In particular, MAAR defines whether an
instruction fetch or data load can speculatively access a memory
region within the physical address bounds specified by MAAR.
As QEMU doesn't do speculative access, hence this patch only
provides ability to access the registers.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
CP0.PageGrain.ELPA enables support for large physical addresses. This field
is encoded as follows:
0: Large physical address support is disabled.
1: Large physical address support is enabled.
If this bit is a 1, the following changes occur to coprocessor 0 registers:
- The PFNX field of the EntryLo0 and EntryLo1 registers is writable and
concatenated with the PFN field to form the full page frame number.
- Access to optional COP0 registers with PA extension, LLAddr, TagLo is
defined.
P5600 can operate in 32-bit or 40-bit Physical Address Mode. Therefore if
XPA is disabled (CP0.PageGrain.ELPA = 0) then assume 32-bit Address Mode.
In MIPS64 assume 36 as default PABITS (when CP0.PageGrain.ELPA = 0).
env->PABITS value is constant and indicates maximum PABITS available on
a core, whereas env->PAMask is calculated from env->PABITS and is also
affected by CP0.PageGrain.ELPA.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Extend EntryLo0, EntryLo1, LLAddr and TagLo from 32 to 64 bits in MIPS32.
Introduce gen_move_low32() function which moves low 32 bits from 64-bit
temp to GPR; it sign extends 32-bit value on MIPS64 and truncates on
MIPS32.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Save MSACSR state. Also remove fp_status, msa_fp_status, hflags and restore
them in post_load() from the architectural registers.
Float exception flags are not present in vmstate. Information they carry
is used only by softfloat caller who translates them into MIPS FCSR.Cause,
FCSR.Flags and then they are cleared. Therefore there is no need for saving
them in vmstate.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Create VMStateDescription for MIPS CPU. The new structure contains exactly the
same fields as before, therefore leaving existing version_id.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Recently added CP0.BadInstr and CP0.BadInstrP registers ended up in cpu_load()
under different offset than in cpu_save(). These and all registers between were
incorrectly restored.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
From MIPS documentation (Volume III):
UserLocal Register (CP0 Register 4, Select 2)
Compliance Level: Recommended.
The UserLocal register is a read-write register that is not interpreted by
the hardware and conditionally readable via the RDHWR instruction.
This register only exists if the Config3-ULRI register field is set.
Privileged software may write this register with arbitrary information and
make it accessible to unprivileged software via register 29 (ULR) of the
RDHWR instruction. To do so, bit 29 of the HWREna register must be set to a
1 to enable unprivileged access to the register.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Scripted conversion:
sed -i "s/CPUState/CPUMIPSState/g" target-mips/*.[hc]
sed -i "s/#define CPUMIPSState/#define CPUState/" target-mips/cpu.h
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Dong Xu Wang <wdongxu@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
The variable CP0_LLAddr represent the full lladdr, not the actual
register value, which is only part of this value and depends on the
CPU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
