Implement the GICv4 VMAPI and VMAPTI commands. These write
an interrupt translation table entry that maps (DeviceID,EventID)
to (vPEID,vINTID,doorbell). The only difference between VMAPI
and VMAPTI is that VMAPI assumes vINTID == EventID rather than
both being specified in the command packet.
(This code won't be reachable until we allow the GIC version to be
set to 4. Support for reading this new virtual-interrupt DTE and
handling it correctly will be implemented in a later commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-9-peter.maydell@linaro.org
The GICv4 defines a new in-guest-memory table for the ITS: this is
the vPE table. Implement the new GITS_BASER2 register which the
guest uses to tell the ITS where the vPE table is located, including
the decode of the register fields into the TableDesc structure which
we do for the GITS_BASER<n> when the guest enables the ITS.
We guard provision of the new register with the its_feature_virtual()
function, which does a check of the GITS_TYPER.Virtual bit which
indicates presence of ITS support for virtual LPIs. Since this bit
is currently always zero, GICv4-specific features will not be
accessible to the guest yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-8-peter.maydell@linaro.org
In process_mapti() we check interrupt IDs to see whether they are
in the valid LPI range. Factor this out into its own utility
function, as we're going to want it elsewhere too for GICv4.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-7-peter.maydell@linaro.org
We use the common function gicv3_idreg() to supply the CoreSight ID
register values for the GICv3 for the copies of these ID registers in
the distributor, redistributor and ITS register frames. This isn't
quite correct, because while most of the register values are the
same, the PIDR0 value should vary to indicate which of these three
frames it is. (You can see this and also the correct values of these
PIDR0 registers by looking at the GIC-600 or GIC-700 TRMs, for
example.)
Make gicv3_idreg() take an extra argument for the PIDR0 value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-5-peter.maydell@linaro.org
Boards using the GICv3 need to configure it with both the total
number of CPUs and also the sizes of all the memory regions which
contain redistributors (one redistributor per CPU). At the moment
the GICv3 checks that the number of CPUs specified is not too many to
fit in the defined redistributor regions, but in fact the code
assumes that the two match exactly. For instance when we set the
GICR_TYPER.Last bit on the final redistributor in each region, we
assume that we don't need to consider the possibility of a region
being only half full of redistributors or even completely empty. We
also assume in gicv3_redist_read() and gicv3_redist_write() that we
can calculate the CPU index from the offset within the MemoryRegion
and that this will always be in range.
Fortunately all the board code sets the redistributor region sizes to
exactly match the CPU count, so this isn't a visible bug. We could
in theory make the GIC code handle non-full redistributor regions, or
have it automatically reduce the provided region sizes to match the
CPU count, but the simplest thing is just to strengthen the error
check and insist that the CPU count and redistributor region size
settings match exactly, since all the board code does that anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-4-peter.maydell@linaro.org
In the GICv3 code we implicitly rely on there being at least one CPU
and thus at least one redistributor and CPU interface. Sanity-check
that the property the board code sets is not zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-3-peter.maydell@linaro.org
In commit b6f96009ac we split do_process_its_cmd() from
process_its_cmd(), but forgot the usual blank line between function
definitions. Add it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-2-peter.maydell@linaro.org
* Add support for Ibex SPI to OpenTitan
* Add support for privileged spec version 1.12.0
* Use privileged spec version 1.12.0 for virt machine by default
* Allow software access to MIP SEIP
* Add initial support for the Sdtrig extension
* Optimisations for vector extensions
* Improvements to the misa ISA string
* Add isa extenstion strings to the device tree
* Don't allow `-bios` options with KVM machines
* Fix NAPOT range computation overflow
* Fix DT property mmu-type when CPU mmu option is disabled
* Make RISC-V ACLINT mtime MMIO register writable
* Add and enable native debug feature
* Support 64bit fdt address.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmJh+GQACgkQIeENKd+X
cFTKZQf/UQ8yb5DozdeNbm2pmfjJnEEsnXB6k95wIX9pjrJ3HkypHzoRpLbIDzET
KsPjRW6N5SLPINrYfgBuxUv0A/6jOG7cTC/Bimu16wPyS2zQopiTTgiJv6qLkO5G
QUBWz/6kaXNT+fQiTnXXqjViADO49FigYRWUmRfNabeUwb6YoQwoBY6B5jpwZlbI
B9qDdcKnYet5zwi1rGFedRC1XtP7ZDF1lylqNS2nnfr1ZvOWYkAJb5TJDi/4qUpz
i/wGRx/8KaYD5ehGe7Xd50sMM9lLlzNgOnZL0F5cRnA8e/3nRFjTeQ7RoSKGBdaS
7J4RqA9YMhuPL2tTq95wof6EpVsSNw==
=yLIg
-----END PGP SIGNATURE-----
Merge tag 'pull-riscv-to-apply-20220422-1' of github.com:alistair23/qemu into staging
First RISC-V PR for QEMU 7.1
* Add support for Ibex SPI to OpenTitan
* Add support for privileged spec version 1.12.0
* Use privileged spec version 1.12.0 for virt machine by default
* Allow software access to MIP SEIP
* Add initial support for the Sdtrig extension
* Optimisations for vector extensions
* Improvements to the misa ISA string
* Add isa extenstion strings to the device tree
* Don't allow `-bios` options with KVM machines
* Fix NAPOT range computation overflow
* Fix DT property mmu-type when CPU mmu option is disabled
* Make RISC-V ACLINT mtime MMIO register writable
* Add and enable native debug feature
* Support 64bit fdt address.
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmJh+GQACgkQIeENKd+X
# cFTKZQf/UQ8yb5DozdeNbm2pmfjJnEEsnXB6k95wIX9pjrJ3HkypHzoRpLbIDzET
# KsPjRW6N5SLPINrYfgBuxUv0A/6jOG7cTC/Bimu16wPyS2zQopiTTgiJv6qLkO5G
# QUBWz/6kaXNT+fQiTnXXqjViADO49FigYRWUmRfNabeUwb6YoQwoBY6B5jpwZlbI
# B9qDdcKnYet5zwi1rGFedRC1XtP7ZDF1lylqNS2nnfr1ZvOWYkAJb5TJDi/4qUpz
# i/wGRx/8KaYD5ehGe7Xd50sMM9lLlzNgOnZL0F5cRnA8e/3nRFjTeQ7RoSKGBdaS
# 7J4RqA9YMhuPL2tTq95wof6EpVsSNw==
# =yLIg
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 21 Apr 2022 05:35:48 PM PDT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* tag 'pull-riscv-to-apply-20220422-1' of github.com:alistair23/qemu: (31 commits)
hw/riscv: boot: Support 64bit fdt address.
hw/core: tcg-cpu-ops.h: Update comments of debug_check_watchpoint()
target/riscv: cpu: Enable native debug feature
target/riscv: machine: Add debug state description
target/riscv: csr: Hook debug CSR read/write
target/riscv: cpu: Add a config option for native debug
target/riscv: debug: Implement debug related TCGCPUOps
hw/intc: riscv_aclint: Add reset function of ACLINT devices
hw/intc: Make RISC-V ACLINT mtime MMIO register writable
hw/intc: Support 32/64-bit mtimecmp and mtime accesses in RISC-V ACLINT
hw/intc: Add .impl.[min|max]_access_size declaration in RISC-V ACLINT
hw/riscv: virt: fix DT property mmu-type when CPU mmu option is disabled
target/riscv/pmp: fix NAPOT range computation overflow
hw/riscv: virt: Exit if the user provided -bios in combination with KVM
target/riscv: Use cpu_loop_exit_restore directly from mmu faults
target/riscv: fix start byte for vmv<nf>r.v when vstart != 0
target/riscv: Add isa extenstion strings to the device tree
target/riscv: misa to ISA string conversion fix
target/riscv: optimize helper for vmv<nr>r.v
target/riscv: optimize condition assign for scale < 0
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The current riscv_load_fdt() forces fdt_load_addr to be placed at a dram address within 3GB,
but not all platforms have dram_base within 3GB.
This patch adds an exception for dram base not within 3GB,
which will place fdt at dram_end align 16MB.
riscv_setup_rom_reset_vec() also needs to be modified
Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220419115945.37945-1-dylan@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This commit implements reset function of all ACLINT devices.
ACLINT device reset will clear MTIME and MSIP register to 0.
Depend on RISC-V ACLINT spec v1.0-rc4:
https://github.com/riscv/riscv-aclint/blob/v1.0-rc4/riscv-aclint.adoc
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220420080901.14655-5-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V privilege spec defines that mtime is exposed as a memory-mapped
machine-mode read-write register. However, as QEMU uses host monotonic
timer as timer source, this makes mtime to be read-only in RISC-V
ACLINT.
This patch makes mtime to be writable by recording the time delta value
between the mtime value to be written and the timer value at the time
mtime is written. Time delta value is then added back whenever the timer
value is retrieved.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220420080901.14655-4-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V privilege spec defines that:
* In RV32, memory-mapped writes to mtimecmp modify only one 32-bit part
of the register.
* For RV64, naturally aligned 64-bit memory accesses to the mtime and
mtimecmp registers are additionally supported and are atomic.
It's possible to perform both 32/64-bit read/write accesses to both
mtimecmp and mtime registers.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Message-Id: <20220420080901.14655-3-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If device's MemoryRegion doesn't have .impl.[min|max]_access_size
declaration, the default access_size_min would be 1 byte and
access_size_max would be 4 bytes (see: softmmu/memory.c).
This will cause a 64-bit memory access to ACLINT to be splitted into
two 32-bit memory accesses.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Message-Id: <20220420080901.14655-2-frank.chang@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The device tree property "mmu-type" is currently exported as either
"riscv,sv32" or "riscv,sv48".
However, the riscv cpu device tree binding [1] has a specific value
"riscv,none" for a HART without a MMU.
Set the device tree property "mmu-type" to "riscv,none" when the CPU mmu
option is disabled using rv32,mmu=off or rv64,mmu=off.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/riscv/cpus.yaml?h=v5.17
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220414155510.1364147-1-niklas.cassel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The -bios option is silently ignored if used in combination with -enable-kvm.
The reason is that the machine starts in S-Mode, and the bios typically runs in
M-Mode.
Better exit in that case to not confuse the user.
Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-Id: <20220401121842.2791796-1-ralf.ramsauer@oth-regensburg.de>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Adds the SPI_HOST device model for ibex. The device specification is as per
[1]. The model has been tested on opentitan with spi_host unit tests
written for TockOS.
[1] https://docs.opentitan.org/hw/ip/spi_host/doc/
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220303045426.511588-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux kernel required alined address of DTB.
But missing align in dtb load function.
Fixed to load to the correct address.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207132758.84403-1-ysato@users.sourceforge.jp>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* hw/arm/virt: Check for attempt to use TrustZone with KVM or HVF
* versal: Add the Cortex-R5s in the Real-Time Processing Unit (RPU) subsystem
* versal: model enough of the Clock/Reset Low-power domain (CRL) to allow control of the Cortex-R5s
* xlnx-zynqmp: Connect 4 TTC timers
* exynos4210: Refactor GIC/combiner code to stop using qemu_split_irq
* realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* hw/core/irq: remove unused 'qemu_irq_split' function
* npcm7xx: use symbolic constants for PWRON STRAP bit fields
* virt: document impact of gic-version on max CPUs
-----BEGIN PGP SIGNATURE-----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=Rke9
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20220421' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* hw/arm/virt: Check for attempt to use TrustZone with KVM or HVF
* versal: Add the Cortex-R5s in the Real-Time Processing Unit (RPU) subsystem
* versal: model enough of the Clock/Reset Low-power domain (CRL) to allow control of the Cortex-R5s
* xlnx-zynqmp: Connect 4 TTC timers
* exynos4210: Refactor GIC/combiner code to stop using qemu_split_irq
* realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
* hw/core/irq: remove unused 'qemu_irq_split' function
* npcm7xx: use symbolic constants for PWRON STRAP bit fields
* virt: document impact of gic-version on max CPUs
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmJhPSUZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3hAsD/4qzZK6LFL4kFH6E4z3tWIn
# ErHrfPGUt/SEfHLP+stQP/loFgkR1SNzcrIZ/HiDCB/W+IqQKuP+tHin2lMhO1tR
# KM6suUO1In2hoxfzimVta4F4GVN8ifY69qUYhaRxcBYSUpRXDNFJGsRIeT5JeUMd
# SArZUifRs7JUo25rIkg5Y+YZE37dmiA5gcuswtoLPa/UlDVqRxihLnItySmeutsc
# /Y8d/iym/ydlhvtL1OUt1KKYeg4ykrPzJCfvopsT2xgkwwB0PYci8//fa5IrRVlp
# Uw6yDssZrDIcXfVz88rdriILaszicCv8lOhTH6I74oXCatiyvi4BEzW8uGqVS8wt
# ff+AaKvGqb5t4GKKhCdpL2NzDwKBGWZHuruACs9IfvMkz62HE12Vr99qAKdQ3s93
# QnFIyUKg90mGkvKy8336zX3hnWjPH8wTASOXbNrgnt6GVLkqwy9ibug5kS+n77eJ
# BnkE5p3OfMVJ5a4o+iZbbDJKfzhNUHDSMIBbG1jRNzax1RgxOBtHFSqP5jmbpm+S
# agyr8h+Md0Tx1dwZKxdCGyvcbSZiG2WxRnci3dyT4MqYY1t1GEpOfcs1EN+CYKwG
# iuezZzJopjOFGaXQaB3OvbvCKxuroHKG61SmDmx+5OkfAxhrqe4ulwYij4jhsyhH
# t8zGzDOKLakv3li90xCX/w==
# =Rke9
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 21 Apr 2022 04:16:53 AM PDT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
* tag 'pull-target-arm-20220421' of https://git.linaro.org/people/pmaydell/qemu-arm: (31 commits)
hw/arm: Use bit fields for NPCM7XX PWRON STRAPs
hw/misc: Add PWRON STRAP bit fields in GCR module
hw/arm/virt: impact of gic-version on max CPUs
hw/core/irq: remove unused 'qemu_irq_split' function
hw/arm/stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
hw/arm/realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ'
hw/arm/exynos4210: Drop Exynos4210Irq struct
hw/arm/exynos4210: Put combiners into state struct
hw/arm/exynos4210: Fold combiner splits into exynos4210_init_board_irqs()
hw/arm/exynos4210: Don't connect multiple lines to external GIC inputs
hw/arm/exynos4210: Connect MCT_G0 and MCT_G1 to both combiners
hw/arm/exynos4210: Fill in irq_table[] for internal-combiner-only IRQ lines
hw/arm/exynos4210: Use TYPE_SPLIT_IRQ in exynos4210_init_board_irqs()
hw/arm/exynos4210: Delete unused macro definitions
hw/arm/exynos4210: Move exynos4210_combiner_get_gpioin() into exynos4210.c
hw/arm/exynos4210: Drop ext_gic_irq[] from Exynos4210Irq struct
hw/arm/exynos4210: Put external GIC into state struct
hw/arm/exynos4210: Move exynos4210_init_board_irqs() into exynos4210.c
hw/arm/exynos4210: Fix code style nit in combiner_grp_to_gic_id[]
hw/arm/exynos4210: Coalesce board_irqs and irq_table
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
G_NORETURN was introduced in glib 2.68, fallback to G_GNUC_NORETURN in
glib-compat.
Note that this attribute must be placed before the function declaration
(bringing a bit of consistency in qemu codebase usage).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Warner Losh <imp@bsdimp.com>
Message-Id: <20220420132624.2439741-20-marcandre.lureau@redhat.com>
While at it, replace '%x' with '%u' as suggested by Philippe Mathieu-Daudé.
Also fixes a GCC 12.0.1 -Wformat-overflow false-positive.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-16-marcandre.lureau@redhat.com>
Also fixes a GCC 12.0.1 false-positive:
../hw/arm/allwinner-a10.c: In function ‘aw_a10_realize’:
../hw/arm/allwinner-a10.c:135:35: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 8 [-Werror=format-overflow=]
135 | sprintf(bus, "usb-bus.%d", i);
| ^~
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-15-marcandre.lureau@redhat.com>
Also fixes a GCC 12.0.1 false-positive:
../hw/arm/digic.c: In function ‘digic_init’:
../hw/arm/digic.c:45:54: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 5 [-Werror=format-truncation=]
45 | snprintf(name, DIGIC_TIMER_NAME_MLEN, "timer[%d]", i);
| ^~
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220420132624.2439741-14-marcandre.lureau@redhat.com>
This patch uses the defined fields to describe PWRON STRAPs for
better readability.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Patrick Venture <venture@google.com>
Message-id: 20220411165842.3912945-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220324181557.203805-3-zongyuan.li@smartx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220324181557.203805-2-zongyuan.li@smartx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only time we use the int_combiner_irq[] and ext_combiner_irq[]
arrays in the Exynos4210Irq struct is during realize of the SoC -- we
initialize them with the input IRQs of the combiner devices, and then
connect those to outputs of other devices in
exynos4210_init_board_irqs(). Now that the combiner objects are
easily accessible as s->int_combiner and s->ext_combiner we can make
the connections directly from one device to the other without going
via these arrays.
Since these are the only two remaining elements of Exynos4210Irq,
we can remove that struct entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-19-peter.maydell@linaro.org
Switch the creation of the combiner devices to the new-style
"embedded in state struct" approach, so we can easily refer
to the object elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-18-peter.maydell@linaro.org
At this point, the function exynos4210_init_board_irqs() splits input
IRQ lines to connect them to the input combiner, output combiner and
external GIC. The function exynos4210_combiner_get_gpioin() splits
some of the combiner input lines further to connect them to multiple
different inputs on the combiner.
Because (unlike qemu_irq_split()) the TYPE_SPLIT_IRQ device has a
configurable number of outputs, we can do all this in one place, by
making exynos4210_init_board_irqs() add extra outputs to the splitter
device when it must be connected to more than one input on each
combiner.
We do this with a new data structure, the combinermap, which is an
array each of whose elements is a list of the interrupt IDs on the
combiner which must be tied together. As we loop through each
interrupt ID, if we find that it is the first one in one of these
lists, we configure the splitter device with eonugh extra outputs and
wire them up to the other interrupt IDs in the list.
Conveniently, for all the cases where this is necessary, the
lowest-numbered interrupt ID in each group is in the range of the
external combiner, so we only need to code for this in the first of
the two loops in exynos4210_init_board_irqs().
The old code in exynos4210_combiner_get_gpioin() which is being
deleted here had several problems which don't exist in the new code
in its handling of the multi-core timer interrupts:
(1) the case labels specified bits 4 ... 8, but bit '8' doesn't
exist; these should have been 4 ... 7
(2) it used the input irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]
multiple times as the input of several different splitters,
which isn't allowed
(3) in an apparent cut-and-paste error, the cases for all the
multi-core timer inputs used "bit + 4" even though the
bit range for the case was (intended to be) 4 ... 7, which
meant it was looking at non-existent bits 8 ... 11.
None of these exist in the new code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-17-peter.maydell@linaro.org
The combiner_grp_to_gic_id[] array includes the EXT_GIC_ID_MCT_G0
and EXT_GIC_ID_MCT_G1 multiple times. This means that we will
connect multiple IRQs up to the same external GIC input, which
is not permitted. We do the same thing in the code in
exynos4210_init_board_irqs() because the conditionals selecting
an irq_id in the first loop match multiple interrupt IDs.
Overall we do this for interrupt IDs
(1, 4), (12, 4), (35, 4), (51, 4), (53, 4) for EXT_GIC_ID_MCT_G0
and
(1, 5), (12, 5), (35, 5), (51, 5), (53, 5) for EXT_GIC_ID_MCT_G1
These correspond to the cases for the multi-core timer that we are
wiring up to multiple inputs on the combiner in
exynos4210_combiner_get_gpioin(). That code already deals with all
these interrupt IDs being the same input source, so we don't need to
connect the external GIC interrupt for any of them except the first
(1, 4) and (1, 5). Remove the array entries and conditionals which
were incorrectly causing us to wire up extra lines.
This bug didn't cause any visible effects, because we only connect
up a device to the "primary" ID values (1, 4) and (1, 5), so the
extra lines would never be set to a level.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-16-peter.maydell@linaro.org
Currently for the interrupts MCT_G0 and MCT_G1 which are
the only ones in the input range of the external combiner
and which are also wired to the external GIC, we connect
them only to the internal combiner and the external GIC.
This seems likely to be a bug, as all other interrupts
which are in the input range of both combiners are
connected to both combiners. (The fact that the code in
exynos4210_combiner_get_gpioin() is also trying to wire
up these inputs on both combiners also suggests this.)
Wire these interrupts up to both combiners, like the rest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-15-peter.maydell@linaro.org
In exynos4210_init_board_irqs(), the loop that handles IRQ lines that
are in a range that applies to the internal combiner only creates a
splitter for those interrupts which go to both the internal combiner
and to the external GIC, but it does nothing at all for the
interrupts which don't go to the external GIC, leaving the
irq_table[] array element empty for those. (This will result in
those interrupts simply being lost, not in a QEMU crash.)
I don't have a reliable datasheet for this SoC, but since we do wire
up one interrupt line in this category (the HDMI I2C device on
interrupt 16,1), this seems like it must be a bug in the existing
QEMU code. Fill in the irq_table[] entries where we're not splitting
the IRQ to both the internal combiner and the external GIC with the
IRQ line of the internal combiner. (That is, these IRQ lines go to
just one device, not multiple.)
This bug didn't have any visible guest effects because the only
implemented device that was affected was the HDMI I2C controller,
and we never connect any I2C devices to that bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-14-peter.maydell@linaro.org
In exynos4210_init_board_irqs(), use the TYPE_SPLIT_IRQ device
instead of qemu_irq_split().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-13-peter.maydell@linaro.org
The function exynos4210_combiner_get_gpioin() currently lives in
exynos4210_combiner.c, but it isn't really part of the combiner
device itself -- it is a function that implements the wiring up of
some interrupt sources to multiple combiner inputs. Move it to live
with the other SoC-level code in exynos4210.c, along with a few
macros previously defined in exynos4210.h which are now used only
in exynos4210.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-11-peter.maydell@linaro.org
The only time we use the ext_gic_irq[] array in the Exynos4210Irq
struct is during realize of the SoC -- we initialize it with the
input IRQs of the external GIC device, and then connect those to
outputs of other devices further on in realize (including in the
exynos4210_init_board_irqs() function). Now that the ext_gic object
is easily accessible as s->ext_gic we can make the connections
directly from one device to the other without going via this array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-10-peter.maydell@linaro.org
Switch the creation of the external GIC to the new-style "embedded in
state struct" approach, so we can easily refer to the object
elsewhere during realize.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-9-peter.maydell@linaro.org
The function exynos4210_init_board_irqs() currently lives in
exynos4210_gic.c, but it isn't really part of the exynos4210.gic
device -- it is a function that implements (some of) the wiring up of
interrupts between the SoC's GIC and combiner components. This means
it fits better in exynos4210.c, which is the SoC-level code. Move it
there. Similarly, exynos4210_git_irq() is used almost only in the
SoC-level code, so move it too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-8-peter.maydell@linaro.org
Fix a missing set of spaces around '-' in the definition of
combiner_grp_to_gic_id[]. We're about to move this code, so
fix the style issue first to keep checkpatch happy with the
code-motion patch.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-7-peter.maydell@linaro.org
The exynos4210 code currently has two very similar arrays of IRQs:
* board_irqs is a field of the Exynos4210Irq struct which is filled
in by exynos4210_init_board_irqs() with the appropriate qemu_irqs
for each IRQ the board/SoC can assert
* irq_table is a set of qemu_irqs pointed to from the
Exynos4210State struct. It's allocated in exynos4210_init_irq,
and the only behaviour these irqs have is that they pass on the
level to the equivalent board_irqs[] irq
The extra indirection through irq_table is unnecessary, so coalesce
these into a single irq_table[] array as a direct field in
Exynos4210State which exynos4210_init_board_irqs() fills in.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-6-peter.maydell@linaro.org
The only time we use the int_gic_irq[] array in the Exynos4210Irq
struct is in the exynos4210_realize() function: we initialize it with
the GPIO inputs of the a9mpcore device, and then a bit later on we
connect those to the outputs of the internal combiner. Now that the
a9mpcore object is easily accessible as s->a9mpcore we can make the
connection directly from one device to the other without going via
this array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-5-peter.maydell@linaro.org
The exynos4210 SoC mostly creates its child devices as if it were
board code. This includes the a9mpcore object. Switch that to a
new-style "embedded in the state struct" creation, because in the
next commit we're going to want to refer to the object again further
down in the exynos4210_realize() function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-4-peter.maydell@linaro.org
Now we have removed the only use of TYPE_EXYNOS4210_IRQ_GATE we can
delete the device entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20220404154658.565020-3-peter.maydell@linaro.org
The Exynos4210 SoC device currently uses a custom device
"exynos4210.irq_gate" to model the OR gate that feeds each CPU's IRQ
line. We have a standard TYPE_OR_IRQ device for this now, so use
that instead.
(This is a migration compatibility break, but that is OK for this
machine type.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404154658.565020-2-peter.maydell@linaro.org
Connect the CRL (Clock Reset LPD) to the Versal SoC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-5-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the Xilinx Versal CRL.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-4-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the Cortex-R5Fs of the Versal RPU (Real-time Processing Unit)
subsystem.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-3-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create an APU CPU Cluster. This is in preparation to add the RPU.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20220406174303.2022038-2-edgar.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 4 TTC timers on the ZynqMP.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20220331222017.2914409-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Break out header file to allow embedding of the the TTC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 20220331222017.2914409-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's not possible to provide the guest with the Security extensions
(TrustZone) when using KVM or HVF, because the hardware
virtualization extensions don't permit running EL3 guest code.
However, we weren't checking for this combination, with the result
that QEMU would assert if you tried it:
$ qemu-system-aarch64 -enable-kvm -machine virt,secure=on -cpu host -display none
Unexpected error in object_property_find_err() at ../../qom/object.c:1304:
qemu-system-aarch64: Property 'host-arm-cpu.secure-memory' not found
Aborted
Check for this combination of options and report an error, in the
same way we already do for attempts to give a KVM or HVF guest the
Virtualization or MTE extensions. Now we will report:
qemu-system-aarch64: mach-virt: KVM does not support providing Security extensions (TrustZone) to the guest CPU
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/961
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220404155301.566542-1-peter.maydell@linaro.org
There are still some files in the QEMU PPC code base that use TABs for
indentation instead of using spaces. The TABs should be replaced so
that we have a consistent coding style.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/374
Signed-off-by: Guo Zhi <qtxuning1999@sjtu.edu.cn>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220412021240.2080218-1-qtxuning1999@sjtu.edu.cn>
[danielhb: trimmed commit msg to 72 chars per line]
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The phb3/phb4/phb5 root ports inherit from the default PCIE root port
implementation, which requests a LSI interrupt (#INTA). On real
hardware (POWER8/POWER9/POWER10), there is no such LSI. This patch
corrects it so that it matches the hardware.
As a consequence, the device tree previously generated was bogus, as
the root bridge LSI was not properly mapped. On some
implementation (powernv9), it was leading to inconsistent interrupt
controller (xive) data. With this patch, it is now clean.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220408131303.147840-3-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This patch skips [de]asserting a LSI interrupt if the device doesn't
have any LSI defined. Doing so would trigger an assert in
pci_irq_handler().
The PCIE root port implementation in qemu requests a LSI (INTA), but a
subclass may want to change that behavior since it's a valid
configuration. For example on the POWER8/POWER9/POWER10 systems, the
root bridge doesn't request any LSI.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220408131303.147840-2-fbarrat@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
There are error paths which do not initialize propname but the trace_exit
label prints it anyway. This initializes the problem string.
Spotted by Coverity CID 1487241.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220406045013.3610172-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Resolves the only compiler warning when building a full QEMU under Arch Linux:
Compiling C object libqemu-ppc-softmmu.fa.p/hw_ppc_ppc405_boards.c.o
In file included from /usr/include/glib-2.0/glib.h:114,
from qemu/include/glib-compat.h:32,
from qemu/include/qemu/osdep.h:132,
from ../src/hw/ppc/ppc405_boards.c:25:
../src/hw/ppc/ppc405_boards.c: In function ‘ref405ep_init’:
/usr/include/glib-2.0/glib/glib-autocleanups.h:28:3: warning: ‘filename’ may be used uninitialized in this function [-Wmaybe-uninitialized]
28 | g_free (*pp);
| ^~~~~~~~~~~~
../src/hw/ppc/ppc405_boards.c:265:26: note: ‘filename’ was declared here
265 | g_autofree char *filename;
| ^~~~~~~~
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220405123534.3395-1-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
These are the spapr virtual hypervisor implementation of the nested
KVM API. They only make sense when running with TCG.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20220325221113.255834-3-farosas@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
I'm moving this because next patch will add more code under the ifdef
and it will be cleaner if we keep them together.
Also switch the ifdef branches to make it more convenient to add code
under CONFIG_TCG in the next patch.
Signed-off-by: Fabiano Rosas <farosas@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20220325221113.255834-2-farosas@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
All devices raising PSI interrupts are now converted to use GPIO lines
and the pnv_psi_irq_set() routines have become useless. Drop them.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220323072846.1780212-5-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Use an anonymous output GPIO line to connect the OCC device with the
PSIHB device and raise the appropriate PSI IRQ line depending on the
processor model.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220323072846.1780212-4-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Create an anonymous output GPIO line to connect the LPC device with
the PSIHB device and raise the appropriate PSI IRQ line depending on
the processor model.
A temporary __pnv_psi_irq_set() routine is introduced to handle the
transition. It will be removed when all devices raising PSI interrupts
are converted to use GPIOs.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220323072846.1780212-3-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
On HW, the PSI and FSP interrupt levels are muxed under the same
interrupt number. For coding reasons, an extra IRQ number was
introduced to index register values in an array. It increased the
count of IRQs which do not fit in the PSI IRQ range anymore.
The PSI and FSP interrupts should be modeled with an extra level of
GPIO lines but since QEMU does not support them, simply drop the extra
number to stay within the IRQ range.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220323072846.1780212-2-clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Recently the LoPAPR spec got a new 2MB pagesize to support in Dynamic DMA
Windows API (DDW), this adds the new flag.
Linux supports it since
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=38727311871
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20220321071945.918669-1-aik@ozlabs.ru>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This header only defines the tcg_allowed variable and the tcg_enabled()
function - which are not required in many files that include this
header. Drop the #include statement there.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220315144107.1012530-1-thuth@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All uses flush output immediately before or after qemu_log_unlock.
Instead of a separate call, move the flush into qemu_log_unlock.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-20-richard.henderson@linaro.org>
Inside qemu_log, we perform qemu_log_trylock/unlock, which need
not be done if we have already performed the lock beforehand.
Always check the result of qemu_log_trylock -- only checking
qemu_loglevel_mask races with the acquisition of the lock on
the logfile.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-10-richard.henderson@linaro.org>
Do not replicate the individual logging statements.
Use qemu_log_trylock/unlock instead of qemu_log directly.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-9-richard.henderson@linaro.org>
This function can fail, which makes it more like ftrylockfile
or pthread_mutex_trylock than flockfile or pthread_mutex_lock,
so rename it.
To closer match the other trylock functions, release rcu_read_lock
along the failure path, so that qemu_log_unlock need not be called
on failure.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220417183019.755276-8-richard.henderson@linaro.org>
* whpx support for breakpoints and stepping
* initial support for Hyper-V Synthetic Debugging
* use monotonic clock for QemuCond and QemuSemaphore
* Remove qemu-common.h include from most units and lots of other clenaups
* do not include headers for all virtio devices in virtio-ccw.h
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmJXCQAUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNT6wf+NHDJUEdDiwaVGVTGXgHuiaycsymi
FpNPiw/+XxSGN5xF3fkUGgqaDrcwIYwVfnXlghKSz8kp1cP3cjxa5CzNMLGTp5je
N6BxFbD7yC6dhagGm3mj32jlsptv3M38OHqKc3t+RaUAotP5RF2VdCyfUBLG6vU0
aMzvMfMtB5aG0D8Fr5EV63t1JMTceFU0YxsG73UCFs2Yx4Z0cGBbNxMbHweRhd1q
tPeVDS46MFPM3/2cGGHpeeqxkoCTU7A9j1VuNQI3k+Kg+6W5YVxiK/UP7bw77E/a
yAHsmIVTNro8ajMBch73weuHtGtdfFLvCKc6QX6aVjzK4dF1voQ01E7gPQ==
=rMle
-----END PGP SIGNATURE-----
Merge tag 'for-upstream' of https://gitlab.com/bonzini/qemu into staging
* Add cpu0-id to query-sev-capabilities
* whpx support for breakpoints and stepping
* initial support for Hyper-V Synthetic Debugging
* use monotonic clock for QemuCond and QemuSemaphore
* Remove qemu-common.h include from most units and lots of other clenaups
* do not include headers for all virtio devices in virtio-ccw.h
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmJXCQAUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroNT6wf+NHDJUEdDiwaVGVTGXgHuiaycsymi
# FpNPiw/+XxSGN5xF3fkUGgqaDrcwIYwVfnXlghKSz8kp1cP3cjxa5CzNMLGTp5je
# N6BxFbD7yC6dhagGm3mj32jlsptv3M38OHqKc3t+RaUAotP5RF2VdCyfUBLG6vU0
# aMzvMfMtB5aG0D8Fr5EV63t1JMTceFU0YxsG73UCFs2Yx4Z0cGBbNxMbHweRhd1q
# tPeVDS46MFPM3/2cGGHpeeqxkoCTU7A9j1VuNQI3k+Kg+6W5YVxiK/UP7bw77E/a
# yAHsmIVTNro8ajMBch73weuHtGtdfFLvCKc6QX6aVjzK4dF1voQ01E7gPQ==
# =rMle
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 13 Apr 2022 10:31:44 AM PDT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [undefined]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (53 commits)
target/i386: Remove unused XMMReg, YMMReg types and CPUState fields
target/i386: do not access beyond the low 128 bits of SSE registers
virtio-ccw: do not include headers for all virtio devices
virtio-ccw: move device type declarations to .c files
virtio-ccw: move vhost_ccw_scsi to a separate file
s390x: follow qdev tree to detect SCSI device on a CCW bus
hw: hyperv: Initial commit for Synthetic Debugging device
hyperv: Add support to process syndbg commands
hyperv: Add definitions for syndbg
hyperv: SControl is optional to enable SynIc
thread-posix: optimize qemu_sem_timedwait with zero timeout
thread-posix: implement Semaphore with QemuCond and QemuMutex
thread-posix: use monotonic clock for QemuCond and QemuSemaphore
thread-posix: remove the posix semaphore support
whpx: Added support for breakpoints and stepping
build-sys: simplify AF_VSOCK check
build-sys: drop ntddscsi.h check
Remove qemu-common.h include from most units
qga: remove explicit environ argument from exec/spawn
Move fcntl_setfl() to oslib-posix
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
A potential Use-after-free was reported in virtio_iommu_handle_command
when using virtio-iommu:
> I find a potential Use-after-free in QEMU 6.2.0, which is in
> virtio_iommu_handle_command() (./hw/virtio/virtio-iommu.c).
>
>
> Specifically, in the loop body, the variable 'buf' allocated at line 639 can be
> freed by g_free() at line 659. However, if the execution path enters the loop
> body again and the if branch takes true at line 616, the control will directly
> jump to 'out' at line 651. At this time, 'buf' is a freed pointer, which is not
> assigned with an allocated memory but used at line 653. As a result, a UAF bug
> is triggered.
>
>
>
> 599 for (;;) {
> ...
> 615 sz = iov_to_buf(iov, iov_cnt, 0, &head, sizeof(head));
> 616 if (unlikely(sz != sizeof(head))) {
> 617 tail.status = VIRTIO_IOMMU_S_DEVERR;
> 618 goto out;
> 619 }
> ...
> 639 buf = g_malloc0(output_size);
> ...
> 651 out:
> 652 sz = iov_from_buf(elem->in_sg, elem->in_num, 0,
> 653 buf ? buf : &tail, output_size);
> ...
> 659 g_free(buf);
>
> We can fix it by set ‘buf‘ to NULL after freeing it:
>
>
> 651 out:
> 652 sz = iov_from_buf(elem->in_sg, elem->in_num, 0,
> 653 buf ? buf : &tail, output_size);
> ...
> 659 g_free(buf);
> +++ buf = NULL;
> 660 }
Fix as suggested by the reporter.
Signed-off-by: Wentao Liang <Wentao_Liang_g@163.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20220407095047.50371-1-mst@redhat.com
Message-ID: <20220406040445-mutt-send-email-mst@kernel.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prevent potential integer overflow by limiting 'width' and 'height' to
512x512. Also change 'datasize' type to size_t. Refer to security
advisory https://starlabs.sg/advisories/22-4206/ for more information.
Fixes: CVE-2021-4206
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220407081712.345609-1-mcascell@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Avoid fetching 'width' and 'height' a second time to prevent possible
race condition. Refer to security advisory
https://starlabs.sg/advisories/22-4207/ for more information.
Fixes: CVE-2021-4207
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220407081106.343235-1-mcascell@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
vmstate_acpi_pcihp_use_acpi_index() was expecting AcpiPciHpState
as state but it actually received PIIX4PMState, because
VMSTATE_PCI_HOTPLUG is a macro and not another struct.
So it ended up accessing random pointer, which resulted
in 'false' return value and acpi_index field wasn't ever
sent.
However in 7.0 that pointer de-references to value > 0, and
destination QEMU starts to expect the field which isn't
sent in migratioon stream from older QEMU (6.2 and older).
As result migration fails with:
qemu-system-x86_64: Missing section footer for 0000:00:01.3/piix4_pm
qemu-system-x86_64: load of migration failed: Invalid argument
In addition with QEMU-6.2, destination due to not expected
state, also never expects the acpi_index field in migration
stream.
Q35 is not affected as it always sends/expects the field as
long as acpi based PCI hotplug is enabled.
Fix issue by introducing compat knob to never send/expect
acpi_index in migration stream for 6.2 and older PC machine
types and always send it for 7.0 and newer PC machine types.
Diagnosed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: b32bd76 ("pci: introduce acpi-index property for PCI device")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/932
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove unecessary use of #ifdef CONFIG_VHOST_SCSI, instead just use a
separate file and a separate rule in meson.build.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do not make assumptions on the parent type of the SCSIDevice, instead
use object_dynamic_cast all the way up to the CcwDevice. This is cleaner
because there is no guarantee that the bus is on a virtio-scsi device;
that is only the case for the default configuration of QEMU's s390x
target.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-5-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynDbg commands can come from two different flows:
1. Hypercalls, in this mode the data being sent is fully
encapsulated network packets.
2. SynDbg specific MSRs, in this mode only the data that needs to be
transfered is passed.
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-4-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynIc can be enabled regardless of the SControl mechanisim which can
register a GSI for a given SintRoute.
This behaviour can achived by setting enabling SIMP and then the guest
will poll on the message slot.
Once there is another message pending the host will set the message slot
with the pending flag.
When the guest polls from the message slot, in case the pending flag is
set it will write to the HV_X64_MSR_EOM indicating it has cleared the
slot and we can try and push our message again.
Signed-off-by: Jon Doron <arilou@gmail.com>
Reviewed-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220216102500.692781-2-arilou@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the global variables with inlined helper functions. getpagesize() is very
likely annotated with a "const" function attribute (at least with glibc), and thus
optimization should apply even better.
This avoids the need for a constructor initialization too.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220323155743.1585078-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert the TARGET_WORDS_BIGENDIAN macro, similarly to what was done
with HOST_BIG_ENDIAN. The new TARGET_BIG_ENDIAN macro is either 0 or 1,
and thus should always be defined to prevent misuse.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Suggested-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-8-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace a config-time define with a compile time condition
define (compatible with clang and gcc) that must be declared prior to
its usage. This avoids having a global configure time define, but also
prevents from bad usage, if the config header wasn't included before.
This can help to make some code independent from qemu too.
gcc supports __BYTE_ORDER__ from about 4.6 and clang from 3.2.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[ For the s390x parts I'm involved in ]
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220323155743.1585078-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
GLib g_get_real_time() is an alternative to gettimeofday() which allows
to simplify our code.
For semihosting, a few bits are lost on POSIX host, but this shouldn't
be a big concern.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220307070401.171986-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds required initialization of Error * variable.
Signed-off-by: Tong Ho <tong.ho@xilinx.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The timebase is allocated during spapr_realize_vcpu() and it's not
freed. This results in memory leaks when doing vcpu unplugs:
==636935==
==636935== 144 (96 direct, 48 indirect) bytes in 1 blocks are definitely lost in loss record 6
,461 of 8,135
==636935== at 0x4897468: calloc (vg_replace_malloc.c:760)
==636935== by 0x5077213: g_malloc0 (in /usr/lib64/libglib-2.0.so.0.6400.4)
==636935== by 0x507757F: g_malloc0_n (in /usr/lib64/libglib-2.0.so.0.6400.4)
==636935== by 0x93C3FB: cpu_ppc_tb_init (ppc.c:1066)
==636935== by 0x97BC2B: spapr_realize_vcpu (spapr_cpu_core.c:268)
==636935== by 0x97C01F: spapr_cpu_core_realize (spapr_cpu_core.c:337)
==636935== by 0xD4626F: device_set_realized (qdev.c:531)
==636935== by 0xD55273: property_set_bool (object.c:2273)
==636935== by 0xD523DF: object_property_set (object.c:1408)
==636935== by 0xD588B7: object_property_set_qobject (qom-qobject.c:28)
==636935== by 0xD52897: object_property_set_bool (object.c:1477)
==636935== by 0xD4579B: qdev_realize (qdev.c:333)
==636935==
This patch adds a cpu_ppc_tb_free() helper in hw/ppc/ppc.c to allow us
to free the timebase. This leak is then solved by calling
cpu_ppc_tb_free() in spapr_unrealize_vcpu().
Fixes: 6f4b5c3ec5 ("spapr: CPU hot unplug support")
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20220329124545.529145-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The patch set adding 9p functionality to darwin introduced an issue
where limits.h, which defines XATTR_SIZE_MAX, is included in 9p.c,
though the referenced constant is needed in 9p.h. This commit fixes that
issue by moving the definition of P9_XATTR_SIZE_MAX, which uses
XATTR_SIZE_MAX, to also be in 9p.c.
Additionally, this commit moves the location of the system headers
include in 9p.c to occur before the project headers (except osdep.h).
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/950
Fixes: 38d7fd68b0 ("9p: darwin: Move XATTR_SIZE_MAX->P9_XATTR_SIZE_MAX")
Signed-off-by: Will Cohen <wwcohen@gmail.com>
Message-Id: <20220331182651.887-1-wwcohen@gmail.com>
[thuth: Adjusted placement of osdep.h]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The vhost-shadow-virtqueue.c build requires include files from
linux-headers/, so it cannot be built on non-Linux systems.
Fortunately it is only needed by vhost-vdpa, so move it there.
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In commit 84d43d2e82 we rearranged the logging of errors in
process_mapc(), and inadvertently dropped the trailing newlines
from the log messages. Restore them. The same commit also
attempted to switch the ICID printing to hex (which is how we
print ICIDs elsewhere) but only did half the job, adding the
0x prefix but leaving the format string at %d; correct to %x.
Fixes: 84d43d2e82 ("hw/intc/arm_gicv3_its: In MAPC with V=0, don't check rdbase field")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
