Implement virtualization extensions in the gic_cpu_read() and
gic_cpu_write() functions. Those are the last bits missing to fully
support virtualization extensions in the CPU interface path.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-14-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_deactivate_irq() and
gic_complete_irq() functions.
When the guest writes an invalid vIRQ to V_EOIR or V_DIR, since the
GICv2 specification is not entirely clear here, we adopt the behaviour
observed on real hardware:
* When V_CTRL.EOIMode is false (EOI split is disabled):
- In case of an invalid vIRQ write to V_EOIR:
-> If some bits are set in H_APR, an invalid vIRQ write to V_EOIR
triggers a priority drop, and increments V_HCR.EOICount.
-> If V_APR is already cleared, nothing happen
- An invalid vIRQ write to V_DIR is ignored.
* When V_CTRL.EOIMode is true:
- In case of an invalid vIRQ write to V_EOIR:
-> If some bits are set in H_APR, an invalid vIRQ write to V_EOIR
triggers a priority drop.
-> If V_APR is already cleared, nothing happen
- An invalid vIRQ write to V_DIR increments V_HCR.EOICount.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180727095421.386-13-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in the gic_acknowledge_irq()
function. This function changes the state of the highest priority IRQ
from pending to active.
When the current CPU is a vCPU, modifying the state of an IRQ modifies
the corresponding LR entry. However if we clear the pending flag before
setting the active one, we lose track of the LR entry as it becomes
invalid. The next call to gic_get_lr_entry() will fail.
To overcome this issue, we call gic_activate_irq() before
gic_clear_pending(). This does not change the general behaviour of
gic_acknowledge_irq.
We also move the SGI case in gic_clear_pending_sgi() to enhance
code readability as the virtualization extensions support adds a if-else
level.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-12-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement virtualization extensions in gic_activate_irq() and
gic_drop_prio() and in gic_get_prio_from_apr_bits() called by
gic_drop_prio().
When the current CPU is a vCPU:
- Use GIC_VIRT_MIN_BPR and GIC_VIRT_NR_APRS instead of their non-virt
counterparts,
- the vCPU APR is stored in the virtual interface, in h_apr.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-11-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some helper functions to gic_internal.h to get or change the state
of an IRQ. When the current CPU is not a vCPU, the call is forwarded to
the GIC distributor. Otherwise, it acts on the list register matching
the IRQ in the current CPU virtual interface.
gic_clear_active can have a side effect on the distributor, even in the
vCPU case, when the correponding LR has the HW field set.
Use those functions in the CPU interface code path to prepare for the
vCPU interface implementation.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-10-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An access to the CPU interface is non-secure if the current GIC instance
implements the security extensions, and the memory access is actually
non-secure. Until then, it was checked with tests such as
if (s->security_extn && !attrs.secure) { ... }
in various places of the CPU interface code.
With the implementation of the virtualization extensions, those tests
must be updated to take into account whether we are in a vCPU interface
or not. This is because the exposed vCPU interface does not implement
security extensions.
This commits replaces all those tests with a call to the
gic_cpu_ns_access() function to check if the current access to the CPU
interface is non-secure. This function takes into account whether the
current CPU is a vCPU or not.
Note that this function is used only in the (v)CPU interface code path.
The distributor code path is left unchanged, as the distributor is not
exposed to vCPUs at all.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180727095421.386-9-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add some helper macros and functions related to the virtualization
extensions to gic_internal.h.
The GICH_LR_* macros help extracting specific fields of a list register
value. The only tricky one is the priority field as only the MSB are
stored. The value must be shifted accordingly to obtain the correct
priority value.
gic_is_vcpu() and gic_get_vcpu_real_id() help with (v)CPU id manipulation
to abstract the fact that vCPU id are in the range
[ GIC_NCPU; (GIC_NCPU + num_cpu) [.
gic_lr_* and gic_virq_is_valid() help with the list registers.
gic_get_lr_entry() returns the LR entry for a given (vCPU, irq) pair. It
is meant to be used in contexts where we know for sure that the entry
exists, so we assert that entry is actually found, and the caller can
avoid the NULL check on the returned pointer.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-8-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the register definitions for the virtual interface of the GICv2.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-7-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the necessary parts of the virtualization extensions state to the
GIC state. We choose to increase the size of the CPU interfaces state to
add space for the vCPU interfaces (the GIC_NCPU_VCPU macro). This way,
we'll be able to reuse most of the CPU interface code for the vCPUs.
The only exception is the APR value, which is stored in h_apr in the
virtual interface state for vCPUs. This is due to some complications
with the GIC VMState, for which we don't want to break backward
compatibility. APRs being stored in 2D arrays, increasing the second
dimension would lead to some ugly VMState description. To avoid
that, we keep it in h_apr for vCPUs.
The vCPUs are numbered from GIC_NCPU to (GIC_NCPU * 2) - 1. The
`gic_is_vcpu` function help to determine if a given CPU id correspond to
a physical CPU or a virtual one.
For the in-kernel KVM VGIC, since the exposed VGIC does not implement
the virtualization extensions, we report an error if the corresponding
property is set to true.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-6-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions are now only used in arm_gic.c, put them static. Some of
them where only used by the NVIC implementation and are not used
anymore, so remove them.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-4-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement GICD_ISACTIVERn and GICD_ICACTIVERn registers in the GICv2.
Those registers allow to set or clear the active state of an IRQ in the
distributor.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-3-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for the virtualization extensions implementation,
refactor the name of the functions and macros that act on the GIC
distributor to make that fact explicit. It will be useful to
differentiate them from the ones that will act on the virtual
interfaces.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The differences from ARMv7-M NVIC are:
* ARMv6-M only supports up to 32 external interrupts
(configurable feature already). The ICTR is reserved.
* Active Bit Register is reserved.
* ARMv6-M supports 4 priority levels against 256 in ARMv7-M.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Forbid stack alignment change. (CCR)
Reserve FAULTMASK, BASEPRI registers.
Report any fault as a HardFault. Disable MemManage, BusFault and
UsageFault, so they always escalated to HardFault. (SHCSR)
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180718095628.26442-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Handle SCS reserved registers listed in ARMv6-M ARM D3.6.1.
All reserved registers are RAZ/WI. ARM_FEATURE_M_MAIN is used for the
checks, because these registers are reserved in ARMv8-M Baseline too.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code currently in gicv3_gicd_no_migration_shift_bug_post_load()
that handles migration from older QEMU versions with a particular
bug is misplaced. We need to run this after migration in all cases,
not just the cases where the "arm_gicv3/gicd_no_migration_shift_bug"
subsection is present, so it must go in a post_load hook for the
top level VMSD, not for the subsection. Move it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180806123445.1459-6-peter.maydell@linaro.org
Contrary to the the impression given in docs/devel/migration.rst,
the migration code does not run the pre_load hook for a
subsection unless the subsection appears on the wire, and so
this is not a place where you can set the default value for
state for the "subsection not present" case. Instead this needs
to be done in a pre_load hook for whatever is the parent VMSD
of the subsection.
We got this wrong in two of the subsection definitions in
the GICv3 migration structs; fix this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20180806123445.1459-5-peter.maydell@linaro.org
Commit 6692aac411 accidentally introduced a second initialization
of the .subsections field of vmstate_gicv3_cpu, instead of adding
the new subsection to the existing list. The effect of this was
probably that migration of GICv3 with virtualization enabled was
broken (or alternatively that migration of ICC_SRE_EL1 was broken,
depending on which of the two initializers the compiler used).
Combine the two into a single list.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-3-peter.maydell@linaro.org
Currently the migration code incorrectly treats a subsection with
no .needed function pointer as if it was the subsection list
terminator -- it is ignored and so is everything after it.
Work around this by giving vmstate_gicv3_gicd_no_migration_shift_bug
a 'needed' function that always returns true.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180806123445.1459-2-peter.maydell@linaro.org
The vmstate save/load code insists that subsections of a VMState must
have names which include their parent VMState's name as a leading
substring. Unfortunately it neither documents this nor checks it on
device init or state save, but instead fails state load with a
confusing error message ("Missing section footer for armv7m_nvic").
Fix the name of the m-security subsection of the NVIC, so that
state save/load works correctly for the security-enabled NVIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180727113854.20283-2-peter.maydell@linaro.org
When we escalate a v8M exception to HardFault, if AIRCR.BFHFNMINNS is
set then we need to decide whether it should become a secure HardFault
or a nonsecure HardFault. We should always escalate to the same
target security state as the original exception. The current code
tries to test this using the 'secure' bool, which is not right because
that flag indicates whether the target security state only for
banked exceptions; the effect was that we were incorrectly escalating
always-secure exceptions like SecureFault to a nonsecure HardFault.
Fix this by defining, logging and using a new 'targets_secure' bool
which tracks the condition we actually want.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180723123457.2038-1-peter.maydell@linaro.org
In icc_dir_write() we were incorrectly checking HCR_EL2.FMO
when determining whether IRQ should be routed to EL2; this should
be HCR_EL2.IMO (compare the GICv3 pseudocode ICC_DIR_EL1[]).
Use the correct mask.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180723180337.17378-1-peter.maydell@linaro.org
The instance_init function of the "exynos4210.gic" device creates a
new "arm_gic" device and immediately realizes it with qdev_init_nofail().
This will leave a lot of object in the QOM tree during introspection of
the "exynos4210.gic" device, e.g. reproducible by starting QEMU like this:
qemu-system-aarch64 -M none -nodefaults -nographic -monitor stdio
And then by running "info qom-tree" at the HMP monitor, followed by
"device_add exynos4210.gic,help" and finally checking "info qom-tree"
again.
Also note that qdev_init_nofail() can exit QEMU in case of errors - and
this must never happen during an instance_init function, otherwise QEMU
could terminate unexpectedly during introspection of a device.
Since most of the code that follows the qdev_init_nofail() depends on
the realized "gicbusdev", the easiest solution to the problem is to
turn the whole instance_init function into a realize function instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1532337784-334-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU currently crashes when introspecting the "iotkit" device and
runnint "info qtree" afterwards, e.g. when running QEMU like this:
echo "{'execute':'qmp_capabilities'} {'execute':'device-list-properties'," \
"'arguments':{'typename':'iotkit'}}" "{'execute': 'human-monitor-command', " \
"'arguments': {'command-line': 'info qtree'}}" | \
aarch64-softmmu/qemu-system-aarch64 -M none,accel=qtest -qmp stdio
Use the new functions object_initialize_child() and sysbus_init_child_obj()
to make sure that all objects get cleaned up correctly when the instances
are destroyed.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1531745974-17187-5-git-send-email-thuth@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICD_ITARGETSR implementation still has some 11MPCore behaviour
that we were incorrectly using in our GICv1 and GICv2 implementations
for the case where the interrupt number is less than GIC_INTERNAL.
The desired behaviour here is:
* for 11MPCore: RAZ/WI for irqs 0..28; read a number matching the
CPU doing the read for irqs 29..31
* for GICv1 and v2: RAZ/WI if uniprocessor; otherwise read a
number matching the CPU doing the read for all irqs < 32
Stop squashing GICD_ITARGETSR to 0 for IRQs 0..28 unless this
is an 11MPCore GIC.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180712154152.32183-3-peter.maydell@linaro.org
In gic_deactivate_irq() the interrupt number comes from the guest
(on a write to the GICC_DIR register), so we need to sanity check
that it isn't out of range before we use it as an array index.
Handle this in a similar manner to the check we do in
gic_complete_irq() for the GICC_EOI register.
The array overrun is not disastrous because the calling code
uses (value & 0x3ff) to extract the interrupt field, so the
only out-of-range values possible are 1020..1023, which allow
overrunning only from irq_state[] into the following
irq_target[] array which the guest can already manipulate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180712154152.32183-2-peter.maydell@linaro.org
Recent cleanup in commit a028dd423e dropped the ICPStateClass::reset
handler. It is now up to child ICP classes to call the DeviceClass::reset
handler of the parent class, thanks to device_class_set_parent_reset().
This is a better object programming pattern, but unfortunately it causes
QEMU to crash during CPU hotplug:
(qemu) device_add host-spapr-cpu-core,id=core1,core-id=1
Segmentation fault (core dumped)
When the hotplug path tries to reset the ICP device, we end up calling:
static void icp_kvm_reset(DeviceState *dev)
{
ICPStateClass *icpc = ICP_GET_CLASS(dev);
icpc->parent_reset(dev);
but icpc->parent_reset is NULL... This happens because icp_kvm_class_init()
calls:
device_class_set_parent_reset(dc, icp_kvm_reset,
&icpc->parent_reset);
but dc->reset, ie, DeviceClass::reset for the TYPE_ICP type, is
itself NULL.
This patch hence sets DeviceClass::reset for the TYPE_ICP type to
point to icp_reset(). It then registers a reset handler that calls
DeviceClass::reset. If the ICP subtype has configured its own reset
handler with device_class_set_parent_reset(), this ensures it will
be called first and it can then call ICPStateClass::parent_reset
safely. This fixes the reset path for the TYPE_KVM_ICP type, which
is the only subtype that defines its own reset function.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Fixes: a028dd423e
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The vector cannot be negative. Coverity now reports this because it sees an
array access before the check, in ioapic_stat_update_irq.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With the previous changes, we can now let the ICS_KVM class inherit
directly from ICS_BASE class and not from the intermediate ICS_SIMPLE.
It makes the class hierarchy much cleaner.
What is left in the top classes is the low level interface to access
the KVM XICS device in ICS_KVM and the XICS emulating handlers in
ICS_SIMPLE.
This should not break migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Just like for the realize handlers, this makes possible to move the
common ICSState code of the reset handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This makes possible to move the common ICSState code of the realize
handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This changes the ICP realize and reset handlers in DeviceRealize and
DeviceReset handlers. parent handlers are now called from the
inheriting classes which is a cleaner object pattern.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's start to use "info pic" just like other platforms. For now we
keep the command for a while so that old users can know what is the new
command to use.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-6-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This include both userspace and in-kernel ioapic. Note that the numbers
can be inaccurate for kvm-ioapic. One reason is the same with
kvm-i8259, that when irqfd is used, irqs can be delivered all inside
kernel without our notice. Meanwhile, kvm-ioapic is specially treated
when irq numbers <ISA_NUM_IRQS, those irqs will be delivered in kernel
too via kvm-i8259 (please refer to kvm_pc_gsi_handler).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
So that now it looks better when with other irqchips.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
People start to use "info pic" for all kinds of irqchip dumps. Let x86
ioapic join the family. It dumps the same thing as "info ioapic".
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-3-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's check if KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION is supported.
If not, we check the number of redist region is equal to 1 and use the
legacy KVM_VGIC_V3_ADDR_TYPE_REDIST attribute. Otherwise we use
the new attribute and allow to register multiple regions to the
KVM device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
for KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION attribute, the attribute
data pointed to by kvm_device_attr.addr is a OR of the
redistributor region address and other fields such as the index
of the redistributor region and the number of redistributors the
region can contain.
The existing machine init done notifier framework sets the address
field to the actual address of the device and does not allow to OR
this value with other fields.
This patch extends the KVMDevice struct with a new kda_addr_ormask
member. Its value is passed at registration time and OR'ed with the
resolved address on kvm_arm_set_device_addr().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529072910-16156-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When either GICD_IPRIORITYR or GICR_IPRIORITYR is read as a 32-bit
register, the post left-shift operator in the for loop causes an
extra shift after the least significant byte has been placed.
The 32-bit value actually returned is therefore the expected value
shifted left by 8 bits.
Signed-off-by: Amol Surati <suratiamol@gmail.com>
Message-id: 20180614054857.26248-1-suratiamol@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On CentOS 7.5, gcc-4.8.5-28.el7_5.1.ppc64le fails to build QEMU due to :
hw/intc/xics_kvm.c: In function ‘ics_set_kvm_state’:
hw/intc/xics_kvm.c:281:13: error: ‘ret’ may be used uninitialized in this
function [-Werror=maybe-uninitialized]
return ret;
Fix the breakage and also remove the extra error reporting as
kvm_device_access() already provides a substantial error message.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Cortex-M CPU and its NVIC are two intimately intertwined parts of
the same hardware; it is not possible to use one without the other.
Unfortunately a lot of our board models don't do any sanity checking
on the CPU type the user asks for, so a command line like
qemu-system-arm -M versatilepb -cpu cortex-m3
will create an M3 without an NVIC, and coredump immediately.
In the other direction, trying a non-M-profile CPU in an M-profile
board won't blow up, but doesn't do anything useful either:
qemu-system-arm -M lm3s6965evb -cpu arm926
Add some checking in the NVIC and CPU realize functions that the
user isn't trying to use an NVIC without an M-profile CPU or
an M-profile CPU without an NVIC, so we can produce a helpful
error message rather than a core dump.
Fixes: https://bugs.launchpad.net/qemu/+bug/1766896
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601160355.15393-1-peter.maydell@linaro.org
While for_each_dist_irq_reg loop starts from GIC_INTERNAL, it forgot to
offset the date array and index. This will overlap the GICR registers
value and leave the last GIC_INTERNAL irq's registers out of update.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The KVM helpers hide the low level interface used to communicate to
the XICS KVM device and provide a good cleanup to the XICS KVM models.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While we skip the GIC_INTERNAL irqs, we don't change the register offset
accordingly. This will overlap the GICR registers value and leave the
last GIC_INTERNAL irq's registers out of update.
Fix this by skipping the registers banked by GICR.
Also for migration compatibility if the migration source (old version
qemu) doesn't send gicd_no_migration_shift_bug = 1 to destination, then
we shift the data of PPI to get the right data for SPI.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1527816987-16108-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
include files shouldn't have the "include/" part, that is implied.
Also, drop an unused include.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
kvm_irqchip_create called by kvm_init will call kvm_init_irq_routing to
initialize global capability variables. If we call kvm_init_irq_routing in
GIC realize function, previous allocated memory will leak.
Fix this by deleting the unnecessary call.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1527750994-14360-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It forgot to increase clroffset during the loop. So it only clear the
first 4 bytes.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1527047633-12368-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There was a nasty flip in identifying which register group an access is
targeting. The issue caused spuriously raised priorities of the guest
when handing CPUs over in the Jailhouse hypervisor.
Cc: qemu-stable@nongnu.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-id: 28b927d3-da58-bce4-cc13-bfec7f9b1cb9@siemens.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead wire up heathrow to the CPU and grackle PCI host using qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This eliminates the need for fetching it from el_change_hook_opaque, and
allows for supporting multiple el_change_hooks without having to hack
something together to find the registered opaque belonging to GICv3.
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1523997485-1905-6-git-send-email-alindsay@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the GIC has the security extension support enabled, then a
non-secure access to ICC_PMR must take account of the non-secure
view of interrupt priorities, where real priorities 0x00..0x7f
are secure-only and not visible to the non-secure guest, and
priorities 0x80..0xff are shown to the guest as if they were
0x00..0xff. We had the logic here wrong:
* on reads, the priority is in the secure range if bit 7
is clear, not if it is set
* on writes, we want to set bit 7, not mask everything else
Our ICC_RPR read code had the same error as ICC_PMR.
(Compare the GICv3 spec pseudocode functions ICC_RPR_EL1
and ICC_PMR_EL1.)
Fixes: https://bugs.launchpad.net/qemu/+bug/1748434
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180315133441.24149-1-peter.maydell@linaro.org
The MemoryListener is registered on address_space_memory, there is
not much to assert. This currently works because the callback
is invoked only once when the listener is registered, but section->fv
is the _new_ FlatView, not the old one on later calls and that
would break.
This confines address_space_to_flatview to exec.c and memory.c.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is to faciliate access to OpenPICState when wiring up the PIC to the macio
controller.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is needed before the next patch because the target-dependent kvm stub
uses the existing kvm_openpic_connect_vcpu() declaration, making it impossible
to move the device-specific declarations into the same file without breaking
ppc-linux-user compilation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This enables the device to be made available during the setup of the Old World
machine. In order to pass back the previous set of IRQs we temporarily introduce
a new pic_irqs parameter until it can be removed.
An additional benefit of this change is that it is also possible to remove the
pic_mem pointer used for macio by accessing the memory region via sysbus.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Presently s390x is the only architecture not exposing specific
CPU information via QMP query-cpus. Upstream discussion has shown
that it could make sense to report the architecture specific CPU
state, e.g. to detect that a CPU has been stopped.
With this change the output of query-cpus will look like this on
s390:
[
{"arch": "s390", "current": true,
"props": {"core-id": 0}, "cpu-state": "operating", "CPU": 0,
"qom_path": "/machine/unattached/device[0]",
"halted": false, "thread_id": 63115},
{"arch": "s390", "current": false,
"props": {"core-id": 1}, "cpu-state": "stopped", "CPU": 1,
"qom_path": "/machine/unattached/device[1]",
"halted": true, "thread_id": 63116}
]
This change doesn't add the s390-specific data to HMP 'info cpus'.
A follow-on patch will remove all architecture specific information
from there.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1518797321-28356-2-git-send-email-mihajlov@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
In many of the NVIC registers relating to interrupts, we
have to convert from a byte offset within a register set
into the number of the first interrupt which is affected.
We were getting this wrong for:
* reads of NVIC_ISPR<n>, NVIC_ISER<n>, NVIC_ICPR<n>, NVIC_ICER<n>,
NVIC_IABR<n> -- in all these cases we were missing the "* 8"
needed to convert from the byte offset to the interrupt number
(since all these registers use one bit per interrupt)
* writes of NVIC_IPR<n> had the opposite problem of a spurious
"* 8" (since these registers use one byte per interrupt)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180209165810.6668-9-peter.maydell@linaro.org
We were previously making the system control register (SCR)
just RAZ/WI. Although we don't implement the functionality
this register controls, we should at least provide the state,
including the banked state for v8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-7-peter.maydell@linaro.org
M profile cores have a similar setup for cache ID registers
to A profile:
* Cache Level ID Register (CLIDR) is a fixed value
* Cache Type Register (CTR) is a fixed value
* Cache Size ID Registers (CCSIDR) are a bank of registers;
which one you see is selected by the Cache Size Selection
Register (CSSELR)
The only difference is that they're in the NVIC memory mapped
register space rather than being coprocessor registers.
Implement the M profile view of them.
Since neither Cortex-M3 nor Cortex-M4 implement caches,
we don't need to update their init functions and can leave
the ctr/clidr/ccsidr[] fields in their ARMCPU structs at zero.
Newer cores (like the Cortex-M33) will want to be able to
set these ID registers to non-zero values, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-6-peter.maydell@linaro.org
The Coprocessor Power Control Register (CPPWR) is new in v8M.
It allows software to control whether coprocessors are allowed
to power down and lose their state. QEMU doesn't have any
notion of power control, so we choose the IMPDEF option of
making the whole register RAZ/WI (indicating that no coprocessors
can ever power down and lose state).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-5-peter.maydell@linaro.org
For M profile cores, cache maintenance operations are done by
writing to special registers in the system register space.
For QEMU, cache operations are always NOPs, since we don't
implement the cache. Implementing these explicitly avoids
a spurious LOG_GUEST_ERROR when the guest uses them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-4-peter.maydell@linaro.org
The PENDNMISET/CLR bits in the ICSR should be RAZ/WI from
NonSecure state if the AIRCR.BFHFNMINS bit is zero. We had
misimplemented this as making the bits RAZ/WI from both
Secure and NonSecure states. Fix this bug by checking
attrs.secure so that Secure code can pend and unpend NMIs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-3-peter.maydell@linaro.org
Instead of hardcoding the values of M profile ID registers in the
NVIC, use the fields in the CPU struct. This will allow us to
give different M profile CPU types different ID register values.
This commit includes the addition of the missing ID_ISAR5,
which exists as RES0 in both v7M and v8M.
(The values of the ID registers might be wrong for the M4 --
this commit leaves the behaviour there unchanged.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-2-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Support M profile derived exceptions on exception entry and exit
* Implement AArch64 v8.2 crypto insns (SHA-512, SHA-3, SM3, SM4)
* Implement working i.MX6 SD controller
* Various devices preparatory to i.MX7 support
* Preparatory patches for SVE emulation
* v8M: Fix bug in implementation of 'TT' insn
* Give useful error if user tries to use userspace GICv3 with KVM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bokK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180209' into staging
target-arm queue:
* Support M profile derived exceptions on exception entry and exit
* Implement AArch64 v8.2 crypto insns (SHA-512, SHA-3, SM3, SM4)
* Implement working i.MX6 SD controller
* Various devices preparatory to i.MX7 support
* Preparatory patches for SVE emulation
* v8M: Fix bug in implementation of 'TT' insn
* Give useful error if user tries to use userspace GICv3 with KVM
# gpg: Signature made Fri 09 Feb 2018 11:01:23 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180209: (30 commits)
hw/core/generic-loader: Allow PC to be set on command line
target/arm/translate.c: Fix missing 'break' for TT insns
target/arm/kvm: gic: Prevent creating userspace GICv3 with KVM
target/arm: Add SVE state to TB->FLAGS
target/arm: Add ZCR_ELx
target/arm: Add SVE to migration state
target/arm: Add predicate registers for SVE
target/arm: Expand vector registers for SVE
hw/arm: Move virt's PSCI DT fixup code to arm/boot.c
usb: Add basic code to emulate Chipidea USB IP
i.MX: Add implementation of i.MX7 GPR IP block
i.MX: Add i.MX7 GPT variant
i.MX: Add code to emulate GPCv2 IP block
i.MX: Add code to emulate i.MX7 SNVS IP-block
i.MX: Add code to emulate i.MX2 watchdog IP block
i.MX: Add code to emulate i.MX7 CCM, PMU and ANALOG IP blocks
hw: i.MX: Convert i.MX6 to use TYPE_IMX_USDHC
sdhci: Add i.MX specific subtype of SDHCI
target/arm: enable user-mode SHA-3, SM3, SM4 and SHA-512 instruction support
target/arm: implement SM4 instructions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently armv7m_nvic_acknowledge_irq() does three things:
* make the current highest priority pending interrupt active
* return a bool indicating whether that interrupt is targeting
Secure or NonSecure state
* implicitly tell the caller which is the highest priority
pending interrupt by setting env->v7m.exception
We need to split these jobs, because v7m_exception_taken()
needs to know whether the pending interrupt targets Secure so
it can choose to stack callee-saves registers or not, but it
must not make the interrupt active until after it has done
that stacking, in case the stacking causes a derived exception.
Similarly, it needs to know the number of the pending interrupt
so it can read the correct vector table entry before the
interrupt is made active, because vector table reads might
also cause a derived exception.
Create a new armv7m_nvic_get_pending_irq_info() function which simply
returns information about the highest priority pending interrupt, and
use it to rearrange the v7m_exception_taken() code so we don't
acknowledge the exception until we've done all the things which could
possibly cause a derived exception.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1517324542-6607-3-git-send-email-peter.maydell@linaro.org
In order to support derived exceptions (exceptions generated in
the course of trying to take an exception), we need to be able
to handle prioritizing whether to take the original exception
or the derived exception.
We do this by introducing a new function
armv7m_nvic_set_pending_derived() which the exception-taking code in
helper.c will call when a derived exception occurs. Derived
exceptions are dealt with mostly like normal pending exceptions, so
we share the implementation with the armv7m_nvic_set_pending()
function.
Note that the way we structure this is significantly different
from the v8M Arm ARM pseudocode: that does all the prioritization
logic in the DerivedLateArrival() function, whereas we choose to
let the existing "identify highest priority exception" logic
do the prioritization for us. The effect is the same, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1517324542-6607-2-git-send-email-peter.maydell@linaro.org
This avoids tons of conversions when handling interrupts.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-19-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This avoids tons of conversions when handling interrupts.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This avoids tons of conversions when handling interrupts.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Kicking all CPUs on every floating interrupt is far from efficient.
Let's optimize it at least a little bit.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-12-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Now that we have access to the io interrupts, we can implement
clear_io_irq() for TCG.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-11-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Move floating interrupt handling into the flic. Floating interrupts
will now be considered by all CPUs, not just CPU #0. While at it, convert
I/O interrupts to use a list and make sure we properly consider I/O
sub-classes in s390_cpu_has_io_int().
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-9-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We can directly call the right function.
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-7-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let the flic device handle it internally. This will allow us to later
on store floating interrupts in the flic for the TCG case.
This now also simplifies kvm.c. All that's left is the fallback
interface for floating interrupts, which is now triggered directly via
the flic in case anything goes wrong.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-6-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We can simply search for an object of our common type.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-4-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This makes it clearer, which device is used for which accelerator.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180129125623.21729-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This is the initial version of the Inter Processor Interrupt device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Add the PMU IO Module Interrupt controller device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
* target/arm: Fix address truncation in 64-bit pagetable walks
* i.MX: Fix FEC/ENET receive functions
* target/arm: preparatory refactoring for SVE emulation
* hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
* hw/intc/arm_gic: Fix C_RPR value on idle priority
* hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
* hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
* hw/arm/virt: Check that the CPU realize method succeeded
* sdhci: fix a NULL pointer dereference due to uninitialized AddressSpace object
* xilinx_spips: Correct usage of an uninitialized local variable
* pl110: Implement vertical compare/next base interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aF9Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180125' into staging
target-arm queue:
* target/arm: Fix address truncation in 64-bit pagetable walks
* i.MX: Fix FEC/ENET receive functions
* target/arm: preparatory refactoring for SVE emulation
* hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
* hw/intc/arm_gic: Fix C_RPR value on idle priority
* hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
* hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
* hw/arm/virt: Check that the CPU realize method succeeded
* sdhci: fix a NULL pointer dereference due to uninitialized AddressSpace object
* xilinx_spips: Correct usage of an uninitialized local variable
* pl110: Implement vertical compare/next base interrupts
# gpg: Signature made Thu 25 Jan 2018 12:59:25 GMT
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180125: (21 commits)
pl110: Implement vertical compare/next base interrupts
xilinx_spips: Correct usage of an uninitialized local variable
sdhci: fix a NULL pointer dereference due to uninitialized AddresSpace object
hw/arm/virt: Check that the CPU realize method succeeded
hw/intc/arm_gic: Fix the NS view of C_BPR when C_CTRL.CBPR is 1
hw/intc/arm_gic: Fix group priority computation for group 1 IRQs
hw/intc/arm_gic: Fix C_RPR value on idle priority
hw/intc/arm_gic: Prevent the GIC from signaling an IRQ when it's "active and pending"
target/arm: Simplify fp_exception_el for user-only
target/arm: Hoist store to flags output in cpu_get_tb_cpu_state
target/arm: Move cpu_get_tb_cpu_state out of line
target/arm: Add ARM_FEATURE_SVE
vmstate: Add VMSTATE_UINT64_SUB_ARRAY
target/arm: Add aa{32, 64}_vfp_{dreg, qreg} helpers
target/arm: Change the type of vfp.regs
target/arm: Use pointers in neon tbl helper
target/arm: Use pointers in neon zip/uzp helpers
target/arm: Use pointers in crypto helpers
target/arm: Mark disas_set_insn_syndrome inline
i.MX: Fix FEC/ENET receive funtions
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When C_CTRL.CBPR is 1, the Non-Secure view of C_BPR is altered:
- A Non-Secure read of C_BPR should return the BPR value plus 1,
saturated to 7,
- A Non-Secure write should be ignored.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-6-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment typo]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When determining the group priority of a group 1 IRQ, if C_CTRL.CBPR is
0, the non-secure BPR value is used. However, this value must be
incremented by one so that it matches the secure world number of
implemented priority bits (NS world has one less priority bit compared
to the Secure world).
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-5-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: add assert, as the gicv3 code has]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When there is no active interrupts in the GIC, a read to the C_RPR
register should return the value of the "Idle priority", which is either
the maximum value an IRQ priority field can be set to, or 0xff.
Since the QEMU GIC model implements all the 8 priority bits, the Idle
priority is 0xff.
Internally, when there is no active interrupt, the running priority
value is 0x100. The gic_get_running_priority function returns an uint8_t
and thus, truncate this value to 0x00 when returning it. This is wrong since
a value of 0x00 correspond to the maximum possible priority.
This commit fixes the returned value when the internal value is 0x100.
Note that it is correct for the Non-Secure view to return 0xff even
though from the NS world point of view, only 7 priority bits are
implemented. The specification states that the Idle priority can be 0xff
even when not all the 8 priority bits are implemented. This has been
verified against a real GICv2 hardware on a Xilinx ZynqMP based board.
Regarding the ARM11MPCore version of the GIC, the specification is not
clear on that point, so this commit does not alter its behavior.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-4-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the GIC, when an IRQ is acknowledged, its state goes from "pending"
to:
- "active" if the corresponding IRQ pin has been de-asserted
- "active and pending" otherwise.
The GICv2 manual states that when a IRQ becomes active (or active and
pending), the GIC should either signal another (higher priority) IRQ to
the CPU if there is one, or de-assert the CPU IRQ pin.
The current implementation of the GIC in QEMU does not check if the
IRQ is already active when looking for pending interrupts with
sufficient priority in gic_update(). This can lead to signaling an
interrupt that is already active.
This usually happens when splitting priority drop and interrupt
deactivation. On priority drop, the IRQ stays active until deactivation.
If it becomes pending again, chances are that it will be incorrectly
selected as best_irq in gic_update().
This commit fixes this by checking if the IRQ is not already active when
looking for best_irq in gic_update().
Note that regarding the ARM11MPCore GIC version, the corresponding
manual is not clear on that point, but it has has no priority
drop/interrupt deactivation separation, so this case should not happen.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-3-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With the LEON3 IRQ controller IRQs can be acknowledged 2 ways:
* Explicitly by software writing to the CLEAR_OFFSET register
* Implicitly when the procesor is done running the trap handler attached
to the IRQ.
The actual IRQMP code only allows the implicit processor triggered IRQ ack.
If software write explicitly to the CLEAR_OFFSET register, this will clear
the pending bit in the register value but this will not lower the ongoing
raised IRQ with the processor. The IRQ will be kept raised to the LEON
processor until the related trap handler is run and the processor implicitly
ack the interrupt. So with the actual IRQMP code trap handler have to be run
even if the software has already done its job by clearing the pending bit.
This feature has been tested on another LEON3 simulator (tsim_leon3 from
Gaisler) and it turns out that the Qemu implementation is not equivalent to
the tsim one. In tsim, if software does clear a pending interrupt before
the related interrupt handler is triggered the said interrupt handler will
not be called.
This patch brings the Qemu IRQMP implementation in line with the tsim
implementation by allowing IRQ to be acknowledged by software only.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The Configurable Fault Status Register for ARMv7M and v8M is
supposed to be byte and halfword accessible, but we were only
implementing word accesses. Add support for the other access
sizes, which are used by the Zephyr RTOS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512742372-31517-1-git-send-email-peter.maydell@linaro.org
The GICv2 specification says that reserved register addresses
must RAZ/WI; now that we implement external abort handling
for Arm CPUs this means we must return MEMTX_OK rather than
MEMTX_ERROR, to avoid generating a spurious guest data abort.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
The GICv3 specification says that reserved register addresses
should RAZ/WI. This means we need to return MEMTX_OK, not MEMTX_ERROR,
because now that we support generating external aborts the
latter will cause an abort on new board models.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
With the previous commit there is now nothing left in sun4m.h so it can be
removed, along with all remaining references to it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com>
This patch adds the function apic_get_highest_priority_irr to
apic.c and exports it through the interface in apic.h for use by hvf.
Signed-off-by: Sergio Andres Gomez Del Real <Sergio.G.DelReal@gmail.com>
Message-Id: <20170913090522.4022-8-Sergio.G.DelReal@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now both classes (i8259, i8259-kvm) support this. Move this upper to
the common class code.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-6-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's leverage the i8259 common code for kvm-i8259 too.
I think it's still possible that stats can lost when i8259 is in kernel
and meanwhile when irqfd is used, e.g., by vfio or vhost devices.
However that should be rare IMHO since they should be using MSIs mostly
if they really want performance (that's why people use vhost and device
assignment), and no old INTx should be used. As long as the INTx users
are emulated in QEMU the stats will be correct.
For "info pic", it should be always accurate since we fetch kvm regs
before dump.
More importantly, it's just too simple to do this now - it's only 10+
LOC to gain this feature.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-5-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It was only for userspace i8259. Move it to general code so that
kvm-i8259 can also use it in the future.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-4-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's not really scary to even enable it forever. After all it's i8259,
and it's even not the kernel one.
Then we can remove quite a few of lines to make it cleaner. And "info
irq" will always work for it.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-3-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One thing to mention is that in pic_set_irq() I need to uncomment a few
lines in the macros to make sure IRQ value calculation is correct.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171210063819.14892-2-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
xics_get_qirq() is only used by the sPAPR machine. Let's move it there
and change its name to reflect its scope. It will be useful for XIVE
support which will use its own set of qirqs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also change the prototype to use a sPAPRMachineState and prefix them
with spapr_irq_. It will let us synchronise the IRQ allocation with
the XIVE interrupt mode when available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'intc' pointer of the CPU references the interrupt presenter in
the XICS interrupt mode. When the XIVE interrupt mode is available and
activated, the machine will need to reassign this pointer to reflect
the change.
Moving this assignment under the realize routine of the CPU will ease
the process when the interrupt mode is toggled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sPAPR and the PowerNV core objects create the interrupt presenter
object of the CPUs in a very similar way. Let's provide a common
routine in which we use the presenter 'type' as a child identifier.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace *printf() with *_report().
Remove trailing new lines.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The previous code section uses a 'first < 0' test and returns. Therefore,
there is no need to test the 'first' variable against '>= 0' afterwards.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the v8M security extension, there should be two systick
devices, which use separate banked systick exceptions. The
register interface is banked in the same way as for other
banked registers, including the existence of an NS alias
region for secure code to access the nonsecure timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-3-git-send-email-peter.maydell@linaro.org
Generalize nvic_sysreg_ns_ops so that we can pass it an
arbitrary MemoryRegion which it will use as the underlying
register implementation to apply the NS-alias behaviour
to. We'll want this so we can do the same with systick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1512154296-5652-2-git-send-email-peter.maydell@linaro.org
Voiding the ITS caches is not supposed to happen via
individual register writes. So we introduced a dedicated
ITS KVM device ioctl to perform a cold reset of the ITS:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_ITS_CTRL_RESET. Let's
use this latter if the kernel supports it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment the ITS is not properly reset and this causes
various bugs on save/restore. We implement a minimalist reset
through individual register writes but for kernel versions
before v4.15 this fails voiding the vITS cache. We cannot
claim we have a comprehensive reset (hence the error message)
but that's better than nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the very beginning, post_load() was called from common
reset. This is not standard and obliged to discriminate the
reset case from the restore case using the iidr value.
Let's get rid of that call.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix an incorrect mask expression in the handling of v7M MPU_RBAR
reads that meant that we would always report the ADDR field as zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1509732813-22957-1-git-send-email-peter.maydell@linaro.org
Remove the last few DPRINTFs from hw/intc/ioapic.c and turn
them into tracing. In one case it's a new trace, in the others
it's just adding a parameter to the existing traces.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20171102180310.24760-1-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When using the emulated XICS, the 'info pic' monitor command shows:
CPU 0 XIRR=ff000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10040060340
1000 MSI 05 00
1001 MSI 05 00
1002 MSI 05 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI 05 00
1009 MSI 05 00
100a MSI 05 00
100b MSI 05 00
100c MSI 05 00
but when using the in-kernel XICS with the very same guest, we get:
CPU 0 XIRR=00000000 ((nil)) PP=ff MFRR=ff
ICS 1000..13ff 0x10032e00340
1000 MSI ff 00
1001 MSI ff 00
1002 MSI ff 00
1003 MSI ff 00
1004 LSI ff 00
1005 LSI ff 00
1006 LSI ff 00
1007 LSI ff 00
1008 MSI ff 00
1009 MSI ff 00
100a MSI ff 00
100b MSI ff 00
100c MSI ff 00
ie, all irqs are masked and XIRR is null, while we should get the
same output as with the emulated XICS.
If the guest is then migrated, 'info pic' shows the expected values
on both source and destination.
The problem is that QEMU doesn't synchronize with KVM before printing
the XICS state. Migration happens to fix the output because it enforces
synchronization with KVM.
To fix the invalid output of 'info pic', this patch introduces a new
synchronize_state operation for both ICPStateClass and ICSStateClass.
The ICP operation relies on run_on_cpu() in order to kick the vCPU
and avoid sleeping on KVM_GET_ONE_REG.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ITS is not fully properly reset at the moment. Caches are
not emptied.
After a reset, in case we attempt to save the state before
the bound devices have registered their MSIs and after the
1st level table has been allocated by the ITS driver
(device BASER is valid), the first level entries are still
invalid. If the device cache is not empty (devices registered
before the reset), vgic_its_save_device_tables fails with -EINVAL.
This causes a QEMU abort().
Cc: qemu-stable@nongnu.org
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: wanghaibin <wanghaibin.wang@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The commit cddafd8f35 ("hw/intc/arm_gicv3_its: Implement state save
/restore") breaks the backward compatibility with the older kernels
where vITS save/restore support is not available. The vmstate function
vm_change_state_handler() should not be registered if the running kernel
doesn't support ITS save/restore feature. Otherwise VM instance will be
killed whenever vmstate callback function is invoked.
Observed a virtual machine shutdown with QEMU-2.10+linux-4.11 when testing
the reboot command "virsh reboot <domain> --mode acpi" instead of reboot.
KVM Error: 'KVM_SET_DEVICE_ATTR failed: Group 4 attr 0x00000000000001'
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1509712671-16299-1-git-send-email-shankerd@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add OpenRISC Multicore PIC which handles inter processor interrupts
(IPI) between cores. In OpenRISC all device interrupts are routed to
each core enabling this device to be simple.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
This calculation of the first exception vector in
the ITNS<n> register being accessed:
int startvec = 32 * (offset - 0x380) + NVIC_FIRST_IRQ;
is incorrect, because offset is in bytes, so we only want
to multiply by 8.
Spotted by Coverity (CID 1381484, CID 1381488), though it is
not correct that it actually overflows the buffer, because
we have a 'startvec + i < s->num_irq' guard.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1507650856-11718-1-git-send-email-peter.maydell@linaro.org
Coverity points out that we forgot the 'break' for
the SAU_CTRL write case (CID1381683). This has
no actual visible consequences because it happens
that the following case is effectively a no-op.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1507742676-9908-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
When we added support for the new SHCSR bits in v8M in commit
437d59c17e the code to support writing to the new HARDFAULTPENDED
bit was accidentally only added for non-secure writes; the
secure banked version of the bit should also be writable.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-21-git-send-email-peter.maydell@linaro.org
Implement the register interface for the SAU: SAU_CTRL,
SAU_TYPE, SAU_RNR, SAU_RBAR and SAU_RLAR. None of the
actual behaviour is implemented here; registers just
read back as written.
When the CPU definition for Cortex-M33 is eventually
added, its initfn will set cpu->sau_sregion, in the same
way that we currently set cpu->pmsav7_dregion for the
M3 and M4.
Number of SAU regions is typically a configurable
CPU parameter, but this patch doesn't provide a
QEMU CPU property for it. We can easily add one when
we have a board that requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-14-git-send-email-peter.maydell@linaro.org
Add the new M profile Secure Fault Status Register
and Secure Fault Address Register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-10-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Reset for devices does not include an automatic clear of the
device state (unlike CPU state, where most of the state
structure is cleared to zero). Add some missing initialization
of NVIC state that meant that the device was left in the wrong
state if the guest did a warm reset.
(In particular, since we were resetting the computed state like
s->exception_prio but not all the state it was computed
from like s->vectors[x].active, the NVIC wound up in an
inconsistent state that could later trigger assertion failures.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1506092407-26985-2-git-send-email-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=/+LV
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20170927a' into staging
Migration pull 2017-09-27
# gpg: Signature made Wed 27 Sep 2017 14:56:23 BST
# gpg: using RSA key 0x0516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20170927a:
migration: Route more error paths
migration: Route errors up through vmstate_save
migration: wire vmstate_save_state errors up to vmstate_subsection_save
migration: Check field save returns
migration: check pre_save return in vmstate_save_state
migration: pre_save return int
migration: disable auto-converge during bulk block migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modify the pre_save method on VMStateDescription to return an int
rather than void so that it potentially can fail.
Changed zillions of devices to make them return 0; the only
case I've made it return non-0 is hw/intc/s390_flic_kvm.c that already
had an error_report/return case.
Note: If you add an error exit in your pre_save you must emit
an error_report to say why.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170925112917.21340-2-dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Apple uses an IBM MPIC2A without timers, it has 64 sources.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Update armv7m_nvic_acknowledge_irq() and armv7m_nvic_complete_irq()
to handle banked exceptions:
* acknowledge needs to use the correct vector, which may be
in sec_vectors[]
* acknowledge needs to return to its caller whether the
exception should be taken to secure or non-secure state
* complete needs its caller to tell it whether the exception
being completed is a secure one or not
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-20-git-send-email-peter.maydell@linaro.org
Handle banking of SHCSR: some register bits are banked between
Secure and Non-Secure, and some are only accessible to Secure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-19-git-send-email-peter.maydell@linaro.org
The ICSR NVIC register is banked for v8M. This doesn't
require any new state, but it does mean that some bits
are controlled by BFHNFNMINS and some bits must work
with the correct banked exception. There is also a new
in v8M PENDNMICLR bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-18-git-send-email-peter.maydell@linaro.org
Now that we have a banked FAULTMASK register and banked exceptions,
we can implement the correct check in cpu_mmu_index() for whether
the MPU_CTRL.HFNMIENA bit's effect should apply. This bit causes
handlers which have requested a negative execution priority to run
with the MPU disabled. In v8M the test has to check this for the
current security state and so takes account of banking.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-17-git-send-email-peter.maydell@linaro.org
Update nvic_exec_prio() to support the v8M changes:
* BASEPRI, FAULTMASK and PRIMASK are all banked
* AIRCR.PRIS can affect NS priorities
* AIRCR.BFHFNMINS affects FAULTMASK behaviour
These changes mean that it's no longer possible to
definitely say that if FAULTMASK is set it overrides
PRIMASK, and if PRIMASK is set it overrides BASEPRI
(since if PRIMASK_NS is set and AIRCR.PRIS is set then
whether that 0x80 priority should take effect or the
priority in BASEPRI_S depends on the value of BASEPRI_S,
for instance). So we switch to the same approach used
by the pseudocode of working through BASEPRI, PRIMASK
and FAULTMASK and overriding the previous values if
needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-16-git-send-email-peter.maydell@linaro.org
If AIRCR.BFHFNMINS is clear, then although NonSecure HardFault
can still be pended via SHCSR.HARDFAULTPENDED it mustn't actually
preempt execution. The simple way to achieve this is to clear the
enable bit for it, since the enable bit isn't guest visible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-15-git-send-email-peter.maydell@linaro.org
In v7M, the fixed-priority exceptions are:
Reset: -3
NMI: -2
HardFault: -1
In v8M, this changes because Secure HardFault may need
to be prioritised above NMI:
Reset: -4
Secure HardFault if AIRCR.BFHFNMINS == 1: -3
NMI: -2
Secure HardFault if AIRCR.BFHFNMINS == 0: -1
NonSecure HardFault: -1
Make these changes, including support for changing the
priority of Secure HardFault as AIRCR.BFHFNMINS changes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-14-git-send-email-peter.maydell@linaro.org
When escalating to HardFault, we must go into Lockup if we
can't take the synchronous HardFault because the current
execution priority is already at or below the priority of
HardFault. In v7M HF is always priority -1 so a simple < 0
comparison sufficed; in v8M the priority of HardFault can
vary depending on whether it is a Secure or NonSecure
HardFault, so we must check against the priority of the
HardFault exception vector we're about to use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-13-git-send-email-peter.maydell@linaro.org
In armv7m_nvic_set_pending() we have to compare the
priority of an exception against the execution priority
to decide whether it needs to be escalated to HardFault.
In the specification this is a comparison against the
exception's group priority; for v7M we implemented it
as a comparison against the raw exception priority
because the two comparisons will always give the
same answer. For v8M the existence of AIRCR.PRIS and
the possibility of different PRIGROUP values for secure
and nonsecure exceptions means we need to explicitly
calculate the vector's group priority for this check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-12-git-send-email-peter.maydell@linaro.org
Make the set_prio() function take a bool indicating
whether to pend the secure or non-secure version of a banked
interrupt, and use this to implement the correct banking
semantics for the SHPR registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-11-git-send-email-peter.maydell@linaro.org
Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending()
functions take a bool indicating whether to pend the secure
or non-secure version of a banked interrupt, and update the
callsites accordingly.
In most callsites we can simply pass the correct security
state in; in a couple of cases we use TODO comments to indicate
that we will return the code in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org
Update the nvic_recompute_state() code to handle the security
extension and its associated banked registers.
Code that uses the resulting cached state (ie the irq
acknowledge and complete code) will be updated in a later
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-9-git-send-email-peter.maydell@linaro.org
For v8M, the NVIC has a new set of registers per interrupt,
NVIC_ITNS<n>. These determine whether the interrupt targets Secure
or Non-secure state. Implement the register read/write code for
these, and make them cause NVIC_IABR, NVIC_ICER, NVIC_ISER,
NVIC_ICPR, NVIC_IPR and NVIC_ISPR to RAZ/WI for non-secure
accesses to fields corresponding to interrupts which are
configured to target secure state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-8-git-send-email-peter.maydell@linaro.org
Update the code in nvic_rettobase() so that it checks the
sec_vectors[] array as well as the vectors[] array if needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-7-git-send-email-peter.maydell@linaro.org
The Application Interrupt and Reset Control Register has some changes
for v8M:
* new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have
real state if the security extension is implemented and otherwise
are constant
* the PRIGROUP field is banked between security states
* non-secure code can be blocked from using the SYSRESET bit
to reset the system if SYSRESETREQS is set
Implement the new state and the changes to register read and write.
For the moment we ignore the effects of the secure PRIGROUP.
We will implement the effects of PRIS and BFHFNMIS later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org
Instead of looking up the pending priority
in nvic_pending_prio(), cache it in a new state struct
field. The calculation of the pending priority given
the interrupt number is more complicated in v8M with
the security extension, so the caching will be worthwhile.
This changes nvic_pending_prio() from returning a full
(group + subpriority) priority value to returning a group
priority. This doesn't require changes to its callsites
because we use it only in comparisons of the form
execution_prio > nvic_pending_prio()
and execution priority is always a group priority, so
a test (exec prio > full prio) is true if and only if
(execprio > group_prio).
(Architecturally the expected comparison is with the
group priority for this sort of "would we preempt" test;
we were only doing a test with a full priority as an
optimisation to avoid the mask, which is possible
precisely because the two comparisons always give the
same answer.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-5-git-send-email-peter.maydell@linaro.org
With banked exceptions, just the exception number in
s->vectpending is no longer sufficient to uniquely identify
the pending exception. Add a vectpending_is_s_banked bool
which is true if the exception is using the sec_vectors[]
array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1505240046-11454-4-git-send-email-peter.maydell@linaro.org
For the v8M security extension, some exceptions must be banked
between security states. Add the new vecinfo array which holds
the state for the banked exceptions and migrate it if the
CPU the NVIC is attached to implements the security extension.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
-----BEGIN PGP SIGNATURE-----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=GAd3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20170915' into staging
ppc patch queue 2017-09-15
Here's the current batch of accumulated ppc patches. These are all
pretty simple bugfixes or cleanups, no big new features here.
# gpg: Signature made Fri 15 Sep 2017 04:50:00 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20170915:
ppc/kvm: use kvm_vm_check_extension() in kvmppc_is_pr()
spapr_events: use QTAILQ_FOREACH_SAFE() in spapr_clear_pending_events()
spapr_cpu_core: cleaning up qdev_get_machine() calls
spapr_pci: don't create 64-bit MMIO window if we don't need to
spapr_pci: convert sprintf() to g_strdup_printf()
spapr_cpu_core: fail gracefully with non-pseries machine types
xics: fix several error leaks
vfio, spapr: Fix levels calculation
spapr_pci: handle FDT creation errors with _FDT()
spapr_pci: use the common _FDT() helper
spapr: fix CAS-generated reset
ppc/xive: fix OV5_XIVE_EXPLOIT bits
spapr: only update SDR1 once per-cpu during CAS
spapr_pci: use g_strdup_printf()
spapr_pci: drop useless check in spapr_populate_pci_child_dt()
spapr_pci: drop useless check in spapr_phb_vfio_get_loc_code()
hw/ppc/spapr.c: cleaning up qdev_get_machine() calls
net: Add SunGEM device emulation as found on Apple UniNorth
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If object_property_get_link() fails then it allocates an error, which
must be freed before returning. The error_get_pretty() function is
merely an accessor to the error message and doesn't free anything.
The error.h header indicates how to do it right:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In several places we were unconditionally applying the
nvic_gprio_mask() to a priority value. This is incorrect
if the priority is one of the fixed negative priority
values (for NMI and HardFault), so don't do it.
This bug would have caused both NMI and HardFault to be
considered as the same priority and so NMI wouldn't
correctly preempt HardFault.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505137930-13255-5-git-send-email-peter.maydell@linaro.org
Make the CFSR register banked if v8M security extensions are enabled.
Not all the bits in this register are banked: the BFSR
bits [15:8] are shared between S and NS, and we store them
in the NS copy of the register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-19-git-send-email-peter.maydell@linaro.org
Make the MMFAR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-18-git-send-email-peter.maydell@linaro.org
Make the CCR register banked if v8M security extensions are enabled.
This is slightly more complicated than the other "add banking"
patches because there is one bit in the register which is not
banked. We keep the live data in the NS copy of the register,
and adjust it on register reads and writes. (Since we don't
currently implement the behaviour that the bit controls, there
is nowhere else that needs to care.)
This patch includes the enforcement of the bits which are newly
RES1 in ARMv8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-17-git-send-email-peter.maydell@linaro.org
Make the MPU_CTRL register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-16-git-send-email-peter.maydell@linaro.org
Make the MPU_RNR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-15-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
We can freely add more items to vmstate_m_security without
breaking migration compatibility, because no CPU currently
has the ARM_FEATURE_M_SECURITY bit enabled and so this
subsection is not yet used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-14-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
For v8M the range 0xe002e000..0xe002efff is an alias region which
for secure accesses behaves like a NonSecure access to the main
SCS region. (For nonsecure accesses including when the security
extension is not implemented, it is RAZ/WI.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-11-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Make the PRIMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of PRIMASK to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-8-git-send-email-peter.maydell@linaro.org
Make the BASEPRI register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of BASEPRI to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-7-git-send-email-peter.maydell@linaro.org
As part of ARMv8M, we need to add support for the PMSAv8 MPU
architecture.
PMSAv8 differs from PMSAv7 both in register/data layout (for instance
using base and limit registers rather than base and size) and also in
behaviour (for example it does not have subregions); rather than
trying to wedge it into the existing PMSAv7 code and data structures,
we define separate ones.
This commit adds the data structures which hold the state for a
PMSAv8 MPU and the register interface to it. The implementation of
the MPU behaviour will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-2-git-send-email-peter.maydell@linaro.org
Fix the following warning:
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: warning: logical not is only applied to the left hand side of this bitwise operator [-Wlogical-not-parentheses]
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^ ~
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses after the '!' to evaluate the bitwise operator first
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
/home/pranith/qemu/hw/intc/arm_gicv3_kvm.c:296:17: note: add parentheses around left hand side expression to silence this warning
if (!c->gicr_ctlr & GICR_CTLR_ENABLE_LPIS) {
^
This logic error meant we were not setting the PTZ
bit when we should -- luckily as the comment suggests
this wouldn't have had any effects beyond making GIC
initialization take a little longer.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Message-id: 20170829173226.7625-1-bobby.prani@gmail.com
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARMv7M architecture specifies that most of the addresses in the
PPB region (which includes the NVIC, systick and system registers)
are not accessible to unprivileged accesses, which should
BusFault with a few exceptions:
* the STIR is configurably user-accessible
* the ITM (which we don't implement at all) is always
user-accessible
Implement this by switching the register access functions
to the _with_attrs scheme that lets us distinguish user
mode accesses.
This allows us to pull the handling of the CCR.USERSETMPEND
flag up to the level where we can make it generate a BusFault
as it should for non-permitted accesses.
Note that until the core ARM CPU code implements turning
MEMTX_ERROR into a BusFault the registers will continue to
act as RAZ/WI to user accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-16-git-send-email-peter.maydell@linaro.org
The armv7m_nvic.h header file was accidentally placed in
include/hw/arm; move it to include/hw/intc to match where
its corresponding .c file lives.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-15-git-send-email-peter.maydell@linaro.org
We currently store the M profile CPU register state PRIMASK and
FAULTMASK in the daif field of the CPU state in its I and F
bits. This is a legacy from the original implementation, which
tried to share the cpu_exec_interrupt code between A profile
and M profile. We've since separated out the two cases because
they are significantly different, so now there is no common
code between M and A profile which looks at env->daif: all the
uses are either in A-only or M-only code paths. Sharing the state
fields now is just confusing, and will make things awkward
when we implement v8M, where the PRIMASK and FAULTMASK
registers are banked between security states.
Switch M profile over to using v7m.faultmask and v7m.primask
fields for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-10-git-send-email-peter.maydell@linaro.org
Remove an out of date comment which says there's only one
item in the NVIC container region -- we put systick into its
own device object a while back and so now there are two
things in the container.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-6-git-send-email-peter.maydell@linaro.org
Let's do it just like the other architectures. Introduce kvm-stub.c
for stubs and kvm_s390x.h for the declarations.
Change license to GPL2+ and keep copyright notice.
As we are dropping the sysemu/kvm.h include from cpu.h, fix up includes.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In trace format '#' flag of printf is forbidden. Fix it to '0x%'.
This patch is created by the following:
check that we have a problem
> find . -name trace-events | xargs grep '%#' | wc -l
56
check that there are no cases with additional printf flags before '#'
> find . -name trace-events | xargs grep "%[-+ 0'I]+#" | wc -l
0
check that there are no wrong usage of '#' and '0x' together
> find . -name trace-events | xargs grep '0x%#' | wc -l
0
fix the problem
> find . -name trace-events | xargs sed -i 's/%#/0x%/g'
[Eric Blake noted that xargs grep '%[-+ 0'I]+#' should be xargs grep
"%[-+ 0'I]+#" instead so the shell quoting is correct.
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170731160135.12101-3-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Almost all of the PMSAv7 state is in the pmsav7 substruct of
the ARM CPU state structure. The exception is the region
number register, which is in cp15.c6_rgnr. This exception
is a bit odd for M profile, which otherwise generally does
not store state in the cp15 substruct.
Rename cp15.c6_rgnr to pmsav7.rnr accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-4-git-send-email-peter.maydell@linaro.org
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During migration we should transfer ais states to the target guest.
This patch introduces a subsection to kvm_s390_flic_vmstate and new
vmsd for qemu_flic. The ais states need to be migrated only when
ais is supported.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
zPCI instructions and facilities are available since IBM zEnterprise
EC12. To support z/PCI in QEMU we enable zpci, aen and ais facilities
starting with zEC12 GA1. And we always set zpci and aen bits in max cpu
model. Later they might be switched off due to applied real cpu model.
For ais bit, we only provide it in the full cpu model beginning with
zEC12 and defer its enablement in the default cpu model to a later point
in time. At the same time, disable them for 2.9 and older machines.
Because of introducing AIS facility, we could check if it's enabled to
initialize flic->ais_supported with the real value.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Although we have recently vmstatified the migration of some css
infrastructure, for some css entities there is still state to be
migrated left, because the focus was keeping migration stream
compatibility (that is basically everything as-is).
Let us add vmstate helpers and extend existing vmstate descriptions so
that we have everything we need. Let us guard the added state via
css_migration_enabled, so we keep the compatible behavior if css
migration is disabled.
Let's also annotate the bits which do not need to be migrated for better
readability.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170711145441.33925-4-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's introduce a specialized way to inject adapter interrupts that,
unlike the common interrupt injection method, allows to take the
characteristics of the adapter into account.
For adapters subject to AIS facility:
- for non-kvm case, we handle the suppression for a given ISC in QEMU.
- for kvm case, we pass adapter id to kvm to do airq injection.
Add add tracepoint for suppressed airq and suppressing airq.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In order to emulate the adapter interruption suppression (AIS)
facility properly, the guest needs to be able to modify the AIS mask.
Interrupt suppression will be handled via the flic (for kvm, via a
recently introduced kernel backend; for !kvm, in the flic code), so
let's introduce a method to change the mode via the flic interface.
We introduce the 'simm' and 'nimm' fields to QEMUS390FLICState
to store interruption modes for each ISC. Each bit in 'simm' and
'nimm' targets one ISC, and collaboratively indicate three modes:
ALL-Interruptions, SINGLE-Interruption and NO-Interruptions. This
interface can initiate most transitions between the states; transition
from SINGLE-Interruption to NO-Interruptions via adapter interrupt
injection will be introduced in a following patch. The meaningful
combinations are as follows:
interruption mode | simm bit | nimm bit
------------------|----------|----------
ALL | 0 | 0
SINGLE | 1 | 0
NO | 1 | 1
Co-authored-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Introduce a new 'flags' field to IoAdapter to contain further
characteristics of the adapter, like whether the adapter is subject to
adapter-interruption suppression.
For the kvm case, pass this value in the 'flags' field when
registering an adapter.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit f6f4ce4211 ("s390x: add property adapter_routes_max_batch",
2016-12-09) introduces a common realize (intended to be common for all
the subclasses) for flic, but fails to make sure the kvm-flic which had
its own is actually calling this common realize.
This omission fortunately does not result in a grave problem. The common
realize was only supposed to catch a possible programming mistake by
validating a value of a property set via the compat machine macros. Since
there was no programming mistake we don't need this fixed for stable.
Let's fix this problem by making sure kvm flic honors the realize of its
parent class.
Let us also improve on the error message we would hypothetically emit
when the validation fails.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: f6f4ce4211 ("s390x: add property adapter_routes_max_batch")
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
From the moment it was introduced by commit a2875e6f98 ("s390x/kvm:
implement floating-interrupt controller device", 2013-07-16) the kvm-flic
is not making realize fail properly in case it's impossible to create the
KVM device which basically serves as a backend and is absolutely
essential for having an operational kvm-flic.
Let's fix this by making sure we do proper error propagation in realize.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Fixes: a2875e6f98 "s390x/kvm: implement floating-interrupt controller device"
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Let's vmstatify virtio_ccw_save_config and virtio_ccw_load_config for
flexibility (extending using subsections) and for fun.
To achieve this we need to hack the config_vector, which is VirtIODevice
(that is common virtio) state, in the middle of the VirtioCcwDevice state
representation. This is somewhat ugly, but we have no choice because the
stream format needs to be preserved.
Almost no changes in behavior. Exception is everything that comes with
vmstate like extra bookkeeping about what's in the stream, and maybe some
extra checks and better error reporting.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <20170703213414.94298-1-pasic@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Previously QEMU open-pic implemented the 4 open-pic timers including
all timer registers, but the timers did not "count" or generate any
interrupts. The patch makes the timers both count and generate
interrupts. The timer clock frequency is fixed at 25MHZ.
--
Responding to V2 patch comments.
- Simplify clock frequency logic and commentary.
- Remove camelCase variables.
- Timer objects now created at init rather than lazily.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICPState objects are currently registered to vmstate as qdev objects.
Their instance ids are hence computed automatically in the migration code,
and thus depends on the order the CPU cores were plugged.
If the destination had its CPU cores plugged in a different order than the
source, then ICPState objects will have different instance_ids and load
the wrong state.
Since CPU objects have a reliable cpu_index which is already used as
instance_id in vmstate, let's use it for ICPState as well.
Please note that this doesn't break migration. Older machine types used to
allocate and realize all ICPState objects at machine init time, for the whole
lifetime of the machine. The qdev instance ids are thus 0,1,2... nr_servers
and happen to map to the vCPU indexes.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In some cases a failing VMSTATE_*_EQUAL does not mean we detected a bug,
but it's actually the best we can do. Especially in these cases a verbose
error message is required.
Let's introduce infrastructure for specifying a error hint to be used if
equal check fails. Let's do this by adding a parameter to the _EQUAL
macros called _err_hint. Also change all current users to pass NULL as
last parameter so nothing changes for them.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170623144823.42936-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
TYPE_ARM_CPU's property "mp-affinity" is defined with
DEFINE_PROP_UINT64().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-35-marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
The getter and setter of TYPE_APIC_COMMON property "id" are
apic_common_get_id() and apic_common_set_id().
apic_common_get_id() reads either APICCommonState member uint32_t
initial_apic_id or uint8_t id into an int64_t local variable. It then
passes this variable to visit_type_int().
apic_common_set_id() uses visit_type_int() to read the value into a
local variable, which it then assigns both to initial_apic_id and id.
While the state backing the property is two unsigned members, 8 and 32
bits wide, the actual visitor is 64 bits signed.
Change getter and setter to use visit_type_uint32(). Then everything's
uint32_t, except for @id.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170607163635.17635-19-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
We change the restoration priority of both the GICv3 and ITS. The
GICv3 must be restored before the ITS and the ITS needs to be restored
before PCIe devices since it translates their MSI transactions.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-id: 1497023553-18411-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the flush of the LPI pending bits into the
redistributor pending tables. This happens on VM stop.
There is no explicit restore as the tables are implicitly sync'ed
on ITS table restore and on LPI enable at redistributor level.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We need to handle both registers and ITS tables. While
register handling is standard, ITS table handling is more
challenging since the kernel API is devised so that the
tables are flushed into guest RAM and not in vmstate buffers.
Flushing the ITS tables on device pre_save() is too late
since the guest RAM is already saved at this point.
Table flushing needs to happen when we are sure the vcpus
are stopped and before the last dirty page saving. The
right point is RUN_STATE_FINISH_MIGRATE but sometimes the
VM gets stopped before migration launch so let's simply
flush the tables each time the VM gets stopped.
For regular ITS registers we just can use vmstate pre_save()
and post_load() callbacks.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1497023553-18411-3-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In some circumstances, we don't want to abort if the
kvm_device_access fails. This will be the case during ITS
migration, in case the ITS table save/restore fails because
the guest did not program the vITS correctly. So let's pass an
error object to the function and return the ioctl value. New
callers will be able to make a decision upon this returned
value.
Existing callers pass &error_abort which will cause the
function to abort on failure.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 1497023553-18411-2-git-send-email-eric.auger@redhat.com
[PMM: wrapped long line]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The static array of interrupt combiner mappings is not modified so it
can be made const for code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are to SysBusDevice variables in exynos4210_gic_realize()
function: one for the device itself and second for arm_gic device. Add
a prefix "gic" to the second one so it will be easier to understand the
code.
While at it, put local uninitialized 'i' variable at the end, next to
other uninitialized ones.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cpu_setup() handler is only implemented by xics_kvm, where it really
does a typical "realize" job. Moreover, the realize() handler is called
shortly after cpu_setup(), on the same path.
This patch converts xics_kvm to implement realize() instead of cpu_setup().
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Until recently, spapr used to allocate ICPState objects for the lifetime
of the machine. They would only be associated to vCPUs in xics_cpu_setup()
when plugging a CPU core.
Now that ICPState objects have the same lifecycle as vCPUs, it is
possible to associate them during realization.
This patch hence open-codes xics_cpu_setup() in icp_realize(). The vCPU
is passed as a property. Note that vCPU now needs to be realized first
for the IRQs to be allocated. It also needs to resetted before ICPState
realization in order to synchronize with KVM.
Since ICPState objects are freed when unrealized, xics_cpu_destroy() isn't
needed anymore and can be safely dropped.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It makes more sense to pass an IPCState * to handlers of ICPStateClass
instead of a DeviceState *, if only to benefit from compile time type
checking. The same goes with ICSStateClass.
While here, we also change the declaration of ICPStateClass in xics.h
for consistency.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These properties are part of the XICS API. They deserve to appear
explicitely in the XICS header file.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Taking into account that qemu_set_irq() returns immediatly if its first
argument is NULL, icp_kvm_reset() largely duplicates icp_reset().
This patch introduces a reset() handler, so that the common logic can
be implemented in icp_reset() only.
While there we can also drop icp_kvm_realize() and icp_kvm_unrealize(). This
causes icp-kvm to be realized in icp_realize(), which sets icp->xics, but
it has no impact.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If EL3 is not implemented (ie only one security state) then the
one and only ICC_BPR1 register behaves like the Non-secure
ICC_BPR1 in an EL3-present configuration. In particular, its
reset value is GIC_MIN_BPR_NS, not GIC_MIN_BPR.
Correct the erroneous reset value; this fixes a problem where
we might hit the assert added in commit a89ff39ee9.
Reported-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1496849369-30282-1-git-send-email-peter.maydell@linaro.org
openpic_tmr_read() is incorrectly computing register offset of the
TCCR, TBCR, TVPR, and TDR registers when accessing the open pic timer
registers. Specifically the offset of timer registers for
openpic_tmr_read() is not accounting for the timer frequency reporting
register (TFFR) which is the first register in the "tmr" memory
region.
openpic_tmr_write() *is* correctly computing the offset by adding
0x10f0 to the address prior to computing the register index. This
patch instead subtracts 0x10 in both the read and write routines and
eliminates some other gratuitous differences between the functions.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----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=tEkM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20170601' into staging
migration/next for 20170601
# gpg: Signature made Thu 01 Jun 2017 17:51:04 BST
# gpg: using RSA key 0xF487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/migration/20170601:
migration: Move include/migration/block.h into migration/
migration: Export ram.c functions in its own file
migration: Create include for migration snapshots
migration: Export rdma.c functions in its own file
migration: Export tls.c functions in its own file
migration: Export socket.c functions in its own file
migration: Export fd.c functions in its own file
migration: Export exec.c functions in its own file
migration: Split qemu-file.h
migration: Remove unneeded includes of migration/vmstate.h
migration: shut src return path unconditionally
migration: fix leak of src file on dst
migration: Remove section_id parameter from vmstate_load
migration: loadvm handlers are not used
migration: Use savevm_handlers instead of loadvm copy
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M series MPU is almost the same as the already implemented R
profile MPU (v7 PMSA). So all we need to implement here is the MPU
register interface in the system register space.
This implementation has the same restriction as the R profile MPU
that it doesn't permit regions to be sized down smaller than 1K.
We also do not yet implement support for MPU_CTRL.HFNMIENA; this
bit should if zero disable use of the MPU when running HardFault,
NMI or with FAULTMASK set to 1 (ie at an execution priority of
less than zero) -- if the MPU is enabled we don't treat these
cases any differently.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Message-id: 1493122030-32191-13-git-send-email-peter.maydell@linaro.org
[PMM: Keep all the bits in mpu_ctrl field, rather than
using SCTLR bits for them; drop broken HFNMIENA support;
various cleanup]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we calculate the mask to use to get the group priority from
an interrupt priority, the way that NS BPR1 is handled differs
from how BPR0 and S BPR1 work -- a BPR1 value of 1 means
the group priority is in bits [7:1], whereas for BPR0 and S BPR1
this is indicated by a 0 BPR value.
Subtract 1 from the BPR value before creating the mask if
we're using the NS BPR value, for both hardware and virtual
interrupts, as the GICv3 pseudocode does, and fix the comments
accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493226792-3237-4-git-send-email-peter.maydell@linaro.org
icc_bpr_write() was not enforcing that writing a value below the
minimum for the BPR should behave as if the BPR was set to the
minimum value. This doesn't make a difference for the secure
BPRs (since we define the minimum for the QEMU implementation
as zero) but did mean we were allowing the NS BPR1 to be set to
0 when 1 should be the lowest value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493226792-3237-3-git-send-email-peter.maydell@linaro.org
We were setting the VBPR1 field of VMCR_EL2 to icv_min_vbpr()
on reset, but this is not correct. The field should reset to
the minimum value of ICV_BPR0_EL1 plus one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493226792-3237-2-git-send-email-peter.maydell@linaro.org
Split the file into public and internal interfaces. I have to rename
the external one because we can't have two include files with the same
name in the same directory. Build system gets confused. The only
exported functions are the ones that handle basic types.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Now that ICPState objects get finalized on CPU unplug, we should unregister
reset handlers as well to avoid a QEMU crash at machine reset time.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit a45863bda9 ("xics_kvm: Don't enable KVM_CAP_IRQ_XICS if
already enabled"), we were able to re-hotplug a vCPU that had been hot-
unplugged ealier, thanks to a boolean flag in ICPState that we set when
enabling KVM_CAP_IRQ_XICS.
This could work because the lifecycle of all ICPState objects was the
same as the machine. Commit 5bc8d26de2 ("spapr: allocate the ICPState
object from under sPAPRCPUCore") broke this assumption and now we always
pass a freshly allocated ICPState object (ie, with the flag unset) to
icp_kvm_cpu_setup().
This cause re-hotplug to fail with:
Unable to connect CPU8 to kernel XICS: Device or resource busy
Let's fix this by caching all the vCPU ids for which KVM_CAP_IRQ_XICS was
enabled. This also drops the now useless boolean flag from ICPState.
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function only does hypercall and RTAS-call registration, and thus
never returns an error. This patch adapt the prototype to reflect that.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
An ioapic device is already created by the q35 initialization
code, and using "-device ioapic" or "-device kvm-ioapic" will
always fail with "Only 1 ioapics allowed". Remove the
user_creatable flag from the ioapic device classes.
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
commit 33cd52b5d7 unset
cannot_instantiate_with_device_add_yet in TYPE_SYSBUS, making all
sysbus devices appear on "-device help" and lack the "no-user"
flag in "info qdm".
To fix this, we can set user_creatable=false by default on
TYPE_SYS_BUS_DEVICE, but this requires setting
user_creatable=true explicitly on the sysbus devices that
actually work with -device.
Fortunately today we have just a few has_dynamic_sysbus=1
machines: virt, pc-q35-*, ppce500, and spapr.
virt, ppce500, and spapr have extra checks to ensure just a few
device types can be instantiated:
* virt supports only TYPE_VFIO_CALXEDA_XGMAC, TYPE_VFIO_AMD_XGBE.
* ppce500 supports only TYPE_ETSEC_COMMON.
* spapr supports only TYPE_SPAPR_PCI_HOST_BRIDGE.
This patch sets user_creatable=true explicitly on those 4 device
classes.
Now, the more complex cases:
pc-q35-*: q35 has no sysbus device whitelist yet (which is a
separate bug). We are in the process of fixing it and building a
sysbus whitelist on q35, but in the meantime we can fix the
"-device help" and "info qdm" bugs mentioned above. Also, despite
not being strictly necessary for fixing the q35 bug, reducing the
list of user_creatable=true devices will help us be more
confident when building the q35 whitelist.
xen: We also have a hack at xen_set_dynamic_sysbus(), that sets
has_dynamic_sysbus=true at runtime when using the Xen
accelerator. This hack is only used to allow xen-backend devices
to be dynamically plugged/unplugged.
This means today we can use -device with the following 22 device
types, that are the ones compiled into the qemu-system-x86_64 and
qemu-system-i386 binaries:
* allwinner-ahci
* amd-iommu
* cfi.pflash01
* esp
* fw_cfg_io
* fw_cfg_mem
* generic-sdhci
* hpet
* intel-iommu
* ioapic
* isabus-bridge
* kvmclock
* kvm-ioapic
* kvmvapic
* SUNW,fdtwo
* sysbus-ahci
* sysbus-fdc
* sysbus-ohci
* unimplemented-device
* virtio-mmio
* xen-backend
* xen-sysdev
This patch adds user_creatable=true explicitly to those devices,
temporarily, just to keep 100% compatibility with existing
behavior of q35. Subsequent patches will remove
user_creatable=true from the devices that are really not meant to
user-creatable on any machine, and remove the FIXME comment from
the ones that are really supposed to be user-creatable. This is
being done in separate patches because we still don't have an
obvious list of devices that will be whitelisted by q35, and I
would like to get each device reviewed individually.
Cc: Alexander Graf <agraf@suse.de>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: Gabriel L. Somlo <somlo@cmu.edu>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Pierre Morel <pmorel@linux.vnet.ibm.com>
Cc: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-block@nongnu.org
Cc: qemu-ppc@nongnu.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Rob Herring <robh@kernel.org>
Cc: Shannon Zhao <zhaoshenglong@huawei.com>
Cc: sstabellini@kernel.org
Cc: Thomas Huth <thuth@redhat.com>
Cc: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: John Snow <jsnow@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-3-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[ehabkost: Small changes at sysbus_device_class_init() comments]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This allows us to remove lots of includes of migration/migration.h
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Kernel commit 17d48610ae0f ("KVM: PPC: Book 3S: XICS: Implement ICS
P/Q states") added new bits to the state used by KVM IRQs. Currently,
QEMU does not preserve these bits, so migrating (or otherwise saving
and restoring) the guest state causes the P and Q bits to be cleared.
Clearing the P bit has no effect, because the kernel will set it based
on other data, but the loss of a set Q bit will cause a lost
interrupt.
This patch preserves the P and Q bits, correcting the problem.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ics_get_kvm_state() "or"s set bits into irq->status but does not mask
out clear bits.
Correct this by initializing the IRQ status to zero before adding bits
to it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This provides a new ICPState object for the PowerNV machine (POWER8).
Access to the Interrupt Management area is done though a memory
region. It contains the registers of the Interrupt Control Presenters
of each thread which are used to accept, return, forward interrupts in
the system.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It will be used by derived classes in PowerNV for customization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, all the ICPs are created before the CPUs, stored in an array
under the sPAPR machine and linked to the CPU when the core threads
are realized. This modeling brings some complexity when a lookup in
the array is required and it can be simplified by allocating the ICPs
when the CPUs are.
This is the purpose of this proposal which introduces a new 'icp_type'
field under the machine and creates the ICP objects of the right type
(KVM or not) before the PowerPCCPU object are.
This change allows more cleanups : the removal of the icps array under
the sPAPR machine and the removal of the xics_get_cpu_index_by_dt_id()
helper.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is the second step to abstract the IRQ 'server' number of the
XICS layer. Now that the prereq cleanups have been done in the
previous patch, we can move down the 'cpu_dt_id' to 'cpu_index'
mapping in the sPAPR machine handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, the ICPState array of the sPAPR machine is indexed with
'cpu_index' of the CPUState. This numbering of CPUs is internal to
QEMU and the guest only knows about what is exposed in the device
tree, that is the 'cpu_dt_id'. This is why sPAPR uses the helper
xics_get_cpu_index_by_dt_id() to do the mapping in a couple of places.
To provide a more generic XICS layer, we need to abstract the IRQ
'server' number and remove any assumption made on its nature. It
should not be used as a 'cpu_index' for lookups like xics_cpu_setup()
and xics_cpu_destroy() do.
To reach that goal, we choose to introduce a generic 'intc' backlink
under PowerPCCPU, and let the machine core init routine do the
ICPState lookup. The resulting object is passed on to xics_cpu_setup()
which does the store under PowerPCCPU. The IRQ 'server' number in XICS
is now generic. sPAPR uses 'cpu_dt_id' and PowerNV will use 'PIR'
number.
This also has the benefit of simplifying the sPAPR hcall routines
which do not need to do any ICPState lookups anymore.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
s390_get_flic() is called many times to obtain the flic. This wastes a
lot of time as it calls object_resolve_path() every time. Let's cache
S390FLICState by defining it as static.
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS needs to be checked before
attempting to read ICC_CTLR_EL1; otherwise kernel versions not
exposing this kvm device group will be incompatible with qemu 2.9.
Fixes: 07a5628 ("hw/intc/arm_gicv3_kvm: Reset GICv3 cpu interface registers")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reported-by: Prakash B <bjsprakash.linux@gmail.com>
Tested-by: Alexander Graf <agraf@suse.de>
Message-id: 1490721640-13052-1-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 07bfa35477.
The global variable is only read as part of a
apic_reset_irq_delivered();
qemu_irq_raise(s->irq);
if (!apic_get_irq_delivered()) {
sequence, so the value never matters at migration time.
Reported-by: Dr. David Alan Gilbert <dglibert@redhat.com>
Cc: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a const qom link between the CPU and the IIC instead
of passing the CPU link through a qom property.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20170317210627.23532-1-marex@denx.de
Cc: Alexander Graf <agraf@suse.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While I was debugging the icount issues I realised a bunch of the
messages look quite similar. I've fixed this by including __func__ in
the debug print. At the same time I move the a modern if (GATE) style
printf which ensures the compiler can check for format string errors
even if the code gets optimised away in the non-DEBUG_GIC case.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The recent changes on the XICS layer removed the XICSState object to
let the sPAPR machine handle the ICP and ICS directly. The reset of
these objects was previously handled by XICSState, which was a SysBus
device, and to keep the same behavior, the ICP and ICS were assigned
to SysbBus.
But that broke the 'info qtree' command in the monitor. 'qtree'
performs a loop on the children of a bus to print their properties and
SysBus devices are expected to be found under SysBus, which is not the
case anymore.
The fix for this problem is to register reset handlers for the ICP and
ICS objects and stop using SysBus for such devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
I was hoping to get this pull request squeezed in before the soft
freeze, but I ran into some difficulties during testing. Everything
here was at least posted before the soft freeze, so I'm hoping we can
still merge it for 2.9.
The biggest things here are:
* Cleanups to handling of hashed page tables, that will make
adding support for the POWER9 MMU easier
* Cleanups to the XICS interrupt controller that will make
implementing the powernv machine easier
* TCG implementation of extended overflow and carry handling for
POWER9
It also includes:
* Increasing the CPU limit for pseries to 1024 vCPUs
* Generating proper OF node names in qemu (making hotplug and
coldplug logic closer together)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gI0E
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170301' into staging
ppc patch queue for 2017-03-01
I was hoping to get this pull request squeezed in before the soft
freeze, but I ran into some difficulties during testing. Everything
here was at least posted before the soft freeze, so I'm hoping we can
still merge it for 2.9.
The biggest things here are:
* Cleanups to handling of hashed page tables, that will make
adding support for the POWER9 MMU easier
* Cleanups to the XICS interrupt controller that will make
implementing the powernv machine easier
* TCG implementation of extended overflow and carry handling for
POWER9
It also includes:
* Increasing the CPU limit for pseries to 1024 vCPUs
* Generating proper OF node names in qemu (making hotplug and
coldplug logic closer together)
# gpg: Signature made Wed 01 Mar 2017 04:43:06 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170301: (50 commits)
Add PowerPC 32-bit guest memory dump support
ppc/xics: rename 'ICPState *' variables to 'icp'
ppc/xics: move InterruptStatsProvider to the sPAPR machine
ppc/xics: move ics-simple post_load under the machine
ppc/xics: remove the XICSState classes
ppc/xics: export the XICS init routines
ppc/xics: move the ICP array under the sPAPR machine
ppc/xics: register the reset handler of ICP objects
ppc/xics: simplify spapr_dt_xics() interface
ppc/xics: use the QOM interface to grab an ICP
ppc/xics: move the cpu_setup() handler under the ICPState class
ppc/xics: simplify the cpu_setup() handler
ppc/xics: move kernel_xics_fd out of KVMXICSState
ppc/xics: extend the QOM interface to handle ICPs
ppc/xics: remove the XICS list of ICS
ppc/xics: register the reset handler of ICS objects
ppc/xics: remove xics_find_source()
ppc/xics: use the QOM interface to resend irqs
ppc/xics: use the QOM interface to get irqs
ppc/xics: use the QOM interface under the sPAPR machine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
'ICPState *' variables are currently named 'ss'. This is confusing, so
let's give them an appropriate name: 'icp'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It provides a better monitor output of the ICP and ICS objects, else
the objects are printed out of order.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ICS object uses a post_load() handler which is implicitly relying
on the fact that the internal state of the ICS and ICP objects has
been restored but this is not guaranteed. So, let's move the code
under the post_load() handler of the machine where we know the objects
have been fully restored.
The icp_resend() handler of the XICSFabric QOM interface is also
removed as it is now obsolete.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XICSState classes are not used anymore. They have now been fully
deprecated by the XICSFabric QOM interface. Do the cleanups.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is nothing left related to the XICS object in the realize
functions of the KVMXICSState and XICSState class. So adapt the
interfaces to call these routines directly from the sPAPR machine init
sequence.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The reset of the ICP objects is currently handled by XICS but this can
be done for each individual ICP.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_dt_xics() only needs the number of servers to build the device
tree nodes. Let's change the routine interface to reflect that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also introduce a xics_icp_get() helper to simplify the changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler is currently under the XICSState class but it
really belongs under ICPState as it is setting up an individual vCPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The cpu_setup() handler currently takes a 'XICSState *' argument to
grab the kernel ICP file descriptor. This interface can be simplified
by using the 'xics' backlink of the ICP object.
This change is also required by subsequent patches which makes use of
the QOM interface for XICS.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The kernel ICP file descriptor is the only reason behind the
KVMXICSState class and it's in the way of more cleanups. Let's make it
a static for the moment and move forward.
If this is problem, we could use an attribute under the sPAPR machine
later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Let's add two new handlers for ICPs. One is to get an ICP object from
a server number and a second is to resend the irqs when needed.
The icp_resend() handler is a temporary workaround needed by the
ics-simple post_load() handler. It will be removed when the post_load
portion can be done at the machine level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
