Fix issue where the data register may be overwritten by next character
reception before being read and returned.
Signed-off-by: Olivier Hériveaux <olivier.heriveaux@ledger.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211128120723.4053-1-olivier.heriveaux@ledger.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ESCC datasheet states that SPEC_ALLSENT is always set in sync mode and set
in async mode once all characters have cleared the transmitter. Since writes to
SERIAL_DATA use a synchronous chardev API, the guest can never see the state when
transmission is in progress so it is possible to set SPEC_ALLSENT in the
R_SPEC register unconditionally.
This fixes a hang when using the Sun PROM as it attempts to enumerate the
onboard serial devices, and a similar hang in OpenBSD SPARC32 where in both cases
the boot process will not proceed until SPEC_ALLSENT has been set after writing
to W_TXCTRL1.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20211118181835.18497-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The "Transmit Interrupts and Transmit Buffer Empty Bit" section of the ESCC
datasheet states the following about the STATUS_TXEMPTY bit: "After a hardware
reset (including a hardware reset by software), or a channel reset, this bit
is set to 1".
Update escc_reset() to set the STATUS_TXEMPTY bit in the R_STATUS register
on device reset as described which fixes a regression whereby the Sun PROM
checks this bit early on startup and gets stuck in an infinite loop if it is
not set.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20211118181835.18497-2-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Normally there are at least two sh_serial instances. Add device id to
trace messages to make it clear which instance they belong to
otherwise its not possible to tell which serial device is accessed.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <cc1f9ff9f4259ae799750e452f8871849c7a104c.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <92902ba34fdf2c8c62232365fbb6531b1036d557.1635541329.git.balaton@eik.bme.hu>
[PMD: Use g_strdup() to initialize DeviceState::id]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Instead of allocating timer with timer_new store it directly in the
state struct. This makes it simpler to free it together with the device.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <fd01eb3720ec32dab06e03019f72f3e177033679.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace fprintf with qemu_log_mask LOG_GUEST_ERROR as the intention is
to handle valid accesses in these functions so if we get to these
errors then it's an invalid access. Do not abort as that would allow
the guest to crash QEMU and the practice in other devices is to not do
that just log and ignore the invalid access. While at it also simplify
the complex bit ops to check if a return value was set which can be
done much simpler and clearer.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <6b46045141d6d9cc32e17c223896fa1116384796.1635541329.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
- Embed SerialMM in MchpPfSoCMMUartState and QOM-initialize it
- Alias SERIAL_MM 'chardev' property on MCHP_PFSOC_UART
- Forward SerialMM sysbus IRQ in mchp_pfsoc_mmuart_realize()
- Add DeviceReset() method
- Add vmstate structure for migration
- Register device in 'input' category
- Keep mchp_pfsoc_mmuart_create() behavior
Note, serial_mm_init() calls qdev_set_legacy_instance_id().
This call is only needed for backwards-compatibility of incoming
migration data with old versions of QEMU which implemented migration
of devices with hand-rolled code. Since this device didn't previously
handle migration at all, then it doesn't need to set the legacy
instance ID.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210925133407.1259392-4-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Our device have 2 different I/O regions:
- a 16550 UART mapped for 32-bit accesses
- 13 extra registers
Instead of mapping each region on the main bus, introduce
a container, map the 2 devices regions on the container,
and map the container on the main bus.
Before:
(qemu) info mtree
...
0000000020100000-000000002010001f (prio 0, i/o): serial
0000000020100020-000000002010101f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020102000-000000002010201f (prio 0, i/o): serial
0000000020102020-000000002010301f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020104000-000000002010401f (prio 0, i/o): serial
0000000020104020-000000002010501f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020106000-000000002010601f (prio 0, i/o): serial
0000000020106020-000000002010701f (prio 0, i/o): mchp.pfsoc.mmuart
After:
(qemu) info mtree
...
0000000020100000-0000000020100fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020100000-000000002010001f (prio 0, i/o): serial
0000000020100020-0000000020100fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020102000-0000000020102fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020102000-000000002010201f (prio 0, i/o): serial
0000000020102020-0000000020102fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020104000-0000000020104fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020104000-000000002010401f (prio 0, i/o): serial
0000000020104020-0000000020104fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020106000-0000000020106fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020106000-000000002010601f (prio 0, i/o): serial
0000000020106020-0000000020106fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210925133407.1259392-3-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current MCHP_PFSOC_MMUART_REG_SIZE definition represent the
size occupied by all the registers. However all registers are
32-bit wide, and the MemoryRegionOps handlers are restricted to
32-bit:
static const MemoryRegionOps mchp_pfsoc_mmuart_ops = {
.read = mchp_pfsoc_mmuart_read,
.write = mchp_pfsoc_mmuart_write,
.impl = {
.min_access_size = 4,
.max_access_size = 4,
},
Avoid being triskaidekaphobic, simplify by using the number of
registers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210925133407.1259392-2-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of sifive_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of shakti_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of ibex_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Rename qbus_create_inplace() to qbus_init(); this is more in line
with our usual naming convention for functions that in-place
initialize objects.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210923121153.23754-5-peter.maydell@linaro.org
We've got SW that expects FSBL (Bootlooader) to setup clocks and
resets. It's quite common that users run that SW on QEMU without
FSBL (FSBL typically requires the Xilinx tools installed). That's
fine, since users can stil use -device loader to enable clocks etc.
To help folks understand what's going, a log (guest-error) message
would be helpful here. In particular with the serial port since
things will go very quiet if they get things wrong.
Suggested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-7-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Read or write to uart registers when unclocked or in reset should be
ignored. Add the check there, and as a result of this, the check in
uart_write_tx_fifo() is now unnecessary.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This converts uart_read() and uart_write() to memop_with_attrs() ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-5-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the clock/reset check is done in uart_receive(), but we
can move the check to uart_can_receive() which is earlier.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present when input clock is disabled, any character transmitted
to tx fifo can still show on the serial line, which is wrong.
Fixes: b636db306e ("hw/char/cadence_uart: add clock support")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210901124521.30599-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After an SDLC "Enter hunt" command has been sent the STATUS_SYNC bit should remain
high until the flag byte has been detected. Whilst the ESCC device doesn't yet
implement SDLC mode, without this change the active low STATUS_SYNC is constantly
asserted causing the MacOS OpenTransport extension to hang on startup as it thinks
it is constantly receiving LocalTalk responses during its initial negotiation
phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This removes duplication of the internal device state initialisation between
device reset and soft reset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that register values at reset are handled elsewhere for all of device reset,
soft reset and hard reset, escc_reset_chn() only needs to handle initialisation
of internal device state.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The hardware reset differs from a device reset in that it only changes the contents
of specific registers. Remove the code that resets all the registers to zero during
hardware reset and implement the default values using the existing soft reset code
with the additional changes listed in the table in the "Z85C30 Reset" section.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The software reset differs from a device reset in that it only changes the contents
of specific registers. Remove the code that resets all the registers to zero during
soft reset and implement the default values listed in the table in the "Z85C30 Reset"
section.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new hardware reset function is to be called for both channels when the
hardware reset bit is written to register WR9. Its initial implementation is
the same as the existing escc_reset_chn() function used for device reset.
Add a new trace event when the guest initiates a hard reset via the WR9 register
to help diagnose guest reset issues.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new software reset function is to be called when the appropriate channel
software reset bit is written to register WR9. Its initial implementation is
the same as the existing escc_reset_chn() function used for device reset.
Add a new trace event when the guest initiates a soft reset via the WR9 register
to help diagnose guest reset issues.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is to ensure that a device reset always returns the ESCC to a known state.
Note that this is currently redundant with the same code in escc_reset_chn()
but that will change shortly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Also fix a couple of spelling mistakes in comments.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Use a dedicated UART config(CONFIG_SHAKTI_UART) to select
shakti uart.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210731190229.137483-1-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Break events are currently only handled by chardev/char-serial.c, so we
just ignore errors, which results in no behaviour change for other
chardevs.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Message-id: 20210806144700.3751979-1-jlu@pengutronix.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since commit 9894dc0cdc "char: convert
from GIOChannel to QIOChannel", the first argument to the watch callback
can actually be a QIOChannel, which is not a GIOChannel (but a QEMU
Object).
Even though we never used that pointer, change the callback type to warn
the users. Possibly a better fix later, we may want to store the
callback and call it from intermediary functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Commit a8fb0a500a ("hw/char: Add Microchip PolarFire SoC MMUART
emulation") added a dependency on the SERIAL model, but forgot to
add the Kconfig selector.
Add the dependency to the MCHP_PFSOC_MMUART symbol to fix when
building the MICROCHIP_PFSOC machine stand-alone:
/usr/bin/ld: libcommon.fa.p/hw_char_mchp_pfsoc_mmuart.c.o: in function `mchp_pfsoc_mmuart_create':
hw/char/mchp_pfsoc_mmuart.c:79: undefined reference to `serial_mm_init'
Fixes: a8fb0a500a ("hw/char: Add Microchip PolarFire SoC MMUART emulation")
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-7-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This QOMifies the SiFive UART model. Migration and reset have been
implemented.
Signed-off-by: Lukas Jünger <lukas.juenger@greensocs.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210616092326.59639-3-lukas.juenger@greensocs.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This cleans up function names in the SiFive UART model.
Signed-off-by: Lukas Jünger <lukas.juenger@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210616092326.59639-2-lukas.juenger@greensocs.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.
We still have several references to the old file, so let's fix them
with the following command:
sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Target lm32 was deprecated in commit d849800512, v5.2.0. See there
for rationale.
Some of its code lives on in device models derived from milkymist
ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c.
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210503084034.3804963-2-armbru@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
[Trivial conflicts resolved, reST markup fixed]
This is the initial implementation of Shakti UART.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210401181457.73039-4-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Stop including cpu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-4-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/sysbus.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210327082804.2259480-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
