The read-only Config4.AE bit set denotes extended 10 bits ASID.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Replace hardcoded 0xbfc00000 with exception_base which is initialized with
this default address so there is no functional change here.
However, it is now exposed and consequently it will be possible to modify
it from outside of the CPU.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch implements read and write access rules for Mips floating
point control and status register (FCR31). The change can be divided
into following parts:
- Add fields that will keep FCR31's R/W bitmask in procesor
definitions and processor float_status structure.
- Add appropriate value for FCR31's R/W bitmask for each supported
processor.
- Add function for setting snan_bit_is_one, and integrate it in
appropriate places.
- Modify handling of CTC1 (case 31) instruction to use FCR31's R/W
bitmask.
- Modify handling user mode executables for Mips, in relation to the
bit EF_MIPS_NAN2008 from ELF header, that is in turn related to
reading and writing to FCR31.
- Modify gdb behavior in relation to FCR31.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
New set of helpers for handling nan2008-syle versions of instructions
<CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>, for Mips R6.
All involved instructions have float operand and integer result. Their
core functionality is implemented via invocations of appropriate SoftFloat
functions. The problematic cases are when the operand is a NaN, and also
when the operand (float) is out of the range of the result.
Here one can distinguish three cases:
CASE MIPS-A: (FCR31.NAN2008 == 1)
1. Operand is a NaN, result should be 0;
2. Operand is larger than INT_MAX, result should be INT_MAX;
3. Operand is smaller than INT_MIN, result should be INT_MIN.
CASE MIPS-B: (FCR31.NAN2008 == 0)
1. Operand is a NaN, result should be INT_MAX;
2. Operand is larger than INT_MAX, result should be INT_MAX;
3. Operand is smaller than INT_MIN, result should be INT_MAX.
CASE SoftFloat:
1. Operand is a NaN, result is INT_MAX;
2. Operand is larger than INT_MAX, result is INT_MAX;
3. Operand is smaller than INT_MIN, result is INT_MIN.
Current implementation of <CEIL|CVT|FLOOR|ROUND|TRUNC>.<L|W>.<S|D>
implements case MIPS-B. This patch relates to case MIPS-A. For case
MIPS-A, only return value for NaN-operands should be corrected after
appropriate SoftFloat library function is called.
Related MSA instructions FTRUNC_S and FTINT_S already handle well
all cases, in the fashion similar to the code from this patch.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com:
* removed a statement from the description which caused slight confusion]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Updated handling of instructions <ABS|NEG>.<S|D>. Note that legacy
(pre-abs2008) ABS and NEG instructions are arithmetic (and, therefore,
any NaN operand causes signaling invalid operation), while abs2008
ones are non-arithmetic, always and only changing the sign bit, even
for NaN-like operands. Details on these instructions are documented
in [1] p. 35 and 359.
Implementation-wise, abs2008 versions are implemented without helpers,
for simplicity and performance sake.
[1] "MIPS Architecture For Programmers Volume II-A:
The MIPS64 Instruction Set Reference Manual",
Imagination Technologies LTD, Revision 6.04, November 13, 2015
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This patch modifies SoftFloat library so that it can be configured in
run-time in relation to the meaning of signaling NaN bit, while, at the
same time, strictly preserving its behavior on all existing platforms.
Background:
In floating-point calculations, there is a need for denoting undefined or
unrepresentable values. This is achieved by defining certain floating-point
numerical values to be NaNs (which stands for "not a number"). For additional
reasons, virtually all modern floating-point unit implementations use two
kinds of NaNs: quiet and signaling. The binary representations of these two
kinds of NaNs, as a rule, differ only in one bit (that bit is, traditionally,
the first bit of mantissa).
Up to 2008, standards for floating-point did not specify all details about
binary representation of NaNs. More specifically, the meaning of the bit
that is used for distinguishing between signaling and quiet NaNs was not
strictly prescribed. (IEEE 754-2008 was the first floating-point standard
that defined that meaning clearly, see [1], p. 35) As a result, different
platforms took different approaches, and that presented considerable
challenge for multi-platform emulators like QEMU.
Mips platform represents the most complex case among QEMU-supported
platforms regarding signaling NaN bit. Up to the Release 6 of Mips
architecture, "1" in signaling NaN bit denoted signaling NaN, which is
opposite to IEEE 754-2008 standard. From Release 6 on, Mips architecture
adopted IEEE standard prescription, and "0" denotes signaling NaN. On top of
that, Mips architecture for SIMD (also known as MSA, or vector instructions)
also specifies signaling bit in accordance to IEEE standard. MSA unit can be
implemented with both pre-Release 6 and Release 6 main processor units.
QEMU uses SoftFloat library to implement various floating-point-related
instructions on all platforms. The current QEMU implementation allows for
defining meaning of signaling NaN bit during build time, and is implemented
via preprocessor macro called SNAN_BIT_IS_ONE.
On the other hand, the change in this patch enables SoftFloat library to be
configured in run-time. This configuration is meant to occur during CPU
initialization, at the moment when it is definitely known what desired
behavior for particular CPU (or any additional FPUs) is.
The change is implemented so that it is consistent with existing
implementation of similar cases. This means that structure float_status is
used for passing the information about desired signaling NaN bit on each
invocation of SoftFloat functions. The additional field in float_status is
called snan_bit_is_one, which supersedes macro SNAN_BIT_IS_ONE.
IMPORTANT:
This change is not meant to create any change in emulator behavior or
functionality on any platform. It just provides the means for SoftFloat
library to be used in a more flexible way - in other words, it will just
prepare SoftFloat library for usage related to Mips platform and its
specifics regarding signaling bit meaning, which is done in some of
subsequent patches from this series.
Further break down of changes:
1) Added field snan_bit_is_one to the structure float_status, and
correspondent setter function set_snan_bit_is_one().
2) Constants <float16|float32|float64|floatx80|float128>_default_nan
(used both internally and externally) converted to functions
<float16|float32|float64|floatx80|float128>_default_nan(float_status*).
This is necessary since they are dependent on signaling bit meaning.
At the same time, for the sake of code cleanup and simplicity, constants
<floatx80|float128>_default_nan_<low|high> (used only internally within
SoftFloat library) are removed, as not needed.
3) Added a float_status* argument to SoftFloat library functions
XXX_is_quiet_nan(XXX a_), XXX_is_signaling_nan(XXX a_),
XXX_maybe_silence_nan(XXX a_). This argument must be present in
order to enable correct invocation of new version of functions
XXX_default_nan(). (XXX is <float16|float32|float64|floatx80|float128>
here)
4) Updated code for all platforms to reflect changes in SoftFloat library.
This change is twofolds: it includes modifications of SoftFloat library
functions invocations, and an addition of invocation of function
set_snan_bit_is_one() during CPU initialization, with arguments that
are appropriate for each particular platform. It was established that
all platforms zero their main CPU data structures, so snan_bit_is_one(0)
in appropriate places is not added, as it is not needed.
[1] "IEEE Standard for Floating-Point Arithmetic",
IEEE Computer Society, August 29, 2008.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Tested-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Tested-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[leon.alrae@imgtec.com:
* cherry-picked 2 chunks from patch #2 to fix compilation warnings]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Information is tracked inside the TCGContext structure, and later used
by tracing events with the 'tcg' and 'vcpu' properties.
The 'cpu' field is used to check tracing of translation-time
events ("*_trans"). The 'tcg_env' field is used to pass it to
execution-time events ("*_exec").
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 146549350162.18437.3033661139638458143.stgit@fimbulvetr.bsc.es
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The arm target was handled by 06486077, but other targets
were ignored. This handles all the rest which actually support
disassembly (that is, skipping moxie and tilegx).
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
exec-all.h contains TCG-specific definitions. It is not needed outside
TCG-specific files such as translate.c, exec.c or *helper.c.
One generic function had snuck into include/exec/exec-all.h; move it to
include/qom/cpu.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In user mode, there's only a static address translation, TBs are always
invalidated properly and direct jumps are reset when mapping change.
Thus the destination address is always valid for direct jumps and
there's no need to restrict it to the pages the TB resides in.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Blue Swirl <blauwirbel@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The MAAR register is a read/write register included in Release 5
of the architecture that defines the accessibility attributes of
physical address regions. In particular, MAAR defines whether an
instruction fetch or data load can speculatively access a memory
region within the physical address bounds specified by MAAR.
As QEMU doesn't do speculative access, hence this patch only
provides ability to access the registers.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reuse CP0_CHECK macro for gen_m{f|t}hc0.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add CP0.ErrCtl register with WST, SPR and ITC bits. In 34K and interAptiv
processors these bits are used to enable CACHE instruction access to
different arrays. When WST=0, SPR=0 and ITC=1 the CACHE instruction will
access ITC tag values.
Generally we do not model caches and we have been treating the CACHE
instruction as NOP. But since CACHE can operate on ITC Tags new
MIPS_HFLAG_ITC_CACHE hflag is introduced to generate the helper only when
CACHE is in the ITC Access mode.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
If the user specifies smp > 1 and the CPU with CM GCR support, then
create Coherent Processing System (which takes care of instantiating CPUs)
rather than CPUs directly and connect i8259 and cbus to the pins exposed by
CPS. However, there is no GIC yet, thus CPS exposes CPU's IRQ pins so use
the same pin numbers as before.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Physical base address for the memory-mapped Coherency Manager Global
Configuration Register space.
The MIPS default location for the GCR_BASE address is 0x1FBF_8.
This register only exists if Config3 CMGCR is set to one.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
[leon.alrae@imgtec.com: move CMGCR enabling to a separate patch]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
MIPS Release 6 and MIPS SIMD Architecture make it mandatory to have IEEE
754-2008 FPU which is indicated by CP1 FIR.HAS2008, FCSR.ABS2008 and
FCSR.NAN2008 bits set to 1.
In QEMU we still keep these bits cleared as there is no 2008-NaN support.
However, this now causes problems preventing from running R6 Linux with
the v4.5 kernel. Kernel refuses to execute 2008-NaN ELFs on a CPU
whose FPU does not support 2008-NaN encoding:
(...)
VFS: Mounted root (ext4 filesystem) readonly on device 8:0.
devtmpfs: mounted
Freeing unused kernel memory: 256K (ffffffff806f0000 - ffffffff80730000)
request_module: runaway loop modprobe binfmt-464c
Starting init: /sbin/init exists but couldn't execute it (error -8)
request_module: runaway loop modprobe binfmt-464c
Starting init: /bin/sh exists but couldn't execute it (error -8)
Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
Therefore always indicate presence of 2008-NaN support in R6 as well as in
R5+MSA CPUs, even though this feature is not yet supported by MIPS in QEMU.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Adds the 'TCGv_env' type for pointers to 'CPUArchState' objects. The
tracing infrastructure later needs to differentiate between regular
pointers and pointers to vCPUs.
Also changes all targets to use the new 'TCGv_env' type instead of the
generic 'TCGv_ptr'. As of now, the change is merely cosmetic ('TCGv_env'
translates into 'TCGv_ptr'), but that could change in the future to
enforce the difference.
Note that a 'TCGv_env' type (for 'CPUState') is not added, since all
helpers currently receive the architecture-specific
pointer ('CPUArchState').
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Acked-by: Richard Henderson <rth@twiddle.net>
Message-id: 145641859552.30295.7821536833590725201.stgit@localhost
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
MIPS Release 6 provides multi-threading features which replace
pre-R6 MT Module. CP0.Config3.MT is always 0 in R6, instead there is new
CP0.Config5.VP (Virtual Processor) bit which indicates presence of
multi-threading support which includes CP0.GlobalNumber register and
DVP/EVP instructions.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Thus, use cpu_env as the parameter, not TCG_AREG0 directly.
Update all uses in the translators.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Split the bits that require it to exec/log.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-id: 1452174932-28657-8-git-send-email-den@openvz.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
If executing ALIGN with shift count bp=0 within mips64 emulation,
the result of the operation should be sign extended.
Taken from the official documentation (pseudo code) :
ALIGN:
tmp_rt_hi = unsigned_word(GPR[rt]) << (8*bp)
tmp_rs_lo = unsigned_word(GPR[rs]) >> (8*(4-bp))
tmp = tmp_rt_hi || tmp_rt_lo
GPR[rd] = sign_extend.32(tmp)
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add SIGRIE (Signal Reserved Instruction Exception) for both MIPS and
microMIPS.
The instruction allows to use the 16-bit code field for software use.
This instruction is introduced by and required as of Release 6.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add Performance Counter (4) and XNP (5) register numbers to RDHWR.
Add check_hwrena() to simplify access control checkings.
Add RDHWR support to microMIPS R6.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add enum for BREAK32
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Some targets already had this within their logic, but make sure
it's present for all targets.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
It is no longer used, so tidy up everything reached by it.
This includes the gen_opc_* arrays, the search_pc parameter
and the inline gen_intermediate_code_internal functions.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The gen_opc_* arrays are already redundant with the data stored in
the insn_start arguments. Transition restore_state_to_opc to use
data from the latter.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Adjust all translators to respect it.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reduce the boilerplate required for each target. At the same time,
move the test for breakpoint after calling tcg_gen_insn_start.
Note that arm and aarch64 do not use cpu_breakpoint_test, but still
move the inline test down after tcg_gen_insn_start.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This does tidy the icount test common to all targets.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
While we're at it, emit the opcode adjacent to where we currently
record data for search_pc. This puts gen_io_start et al on the
"correct" side of the marker.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
With an eye toward making it mandatory.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This patch improves exception handling in MIPS.
Instructions generate several types of exceptions.
When exception is generated, it breaks the execution of the current
translation block. Implementation of the exceptions handling does not
correctly restore icount for the instruction which caused the exception.
In most cases icount will be decreased by the value equal to the size of
TB. This patch passes pointer to the translation block internals to the
exception handler. It allows correct restoring of the icount value.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: avoid retranslation in linux-user SC, break lines
which are over 80 chars, remove v3 changelog from the commit message]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
MTC0 on a 64-bit processor should move entire 64-bit GPR content to CP0
register.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
rs cannot be the zero register, Reserved Instruction exception must be
signalled for this case.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
MIPS_DEBUG_SIGN_EXTENSIONS was used sometimes ago to verify that 32-bit
instructions correctly sign extend their results. It's now not need
anymore, remove it.
Cc: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
MIPS_DEBUG is a define used to dump the instruction disassembling. It
has to be defined at compile time. In practice I believe it's more
efficient to just look at the instruction disassembly and op dump using
-d in_asm,op. This patch therefore removes the corresponding code, which
clutters translate.c.
Cc: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Instructions recip.{s|d} and rsqrt.{s|d} do not require 64-bit FPU neither
they require any particular mode for its FPU. This patch removes the checks
that may break a program that uses these instructions.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
We can tidy gen_load_fpr32h, as well as introduce a helper
to cleanup the MACC instructions.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
The LWL/LDL instructions mask the GPR with a mask depending on the
address alignement. It is currently computed by doing:
mask = 0x7fffffffffffffffull >> (t1 ^ 63)
It's simpler to generate it by doing:
mask = ~(-1 << t1)
It uses one TCG instruction less, and it avoids a 32/64-bit constant
loading which can take a few instructions on RISC hosts.
Cc: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
The checks in dins is required to avoid triggering an assertion
in tcg_gen_deposit_tl. The check in dext is just for completeness.
Fold the other D cases in via fallthru.
In this case the errant dins appears to be data, not code, as
translation failed to stop after a break insn.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In semihosting mode the SDBBP 1 instructions should trigger UHI syscall,
but in QEMU this does not happen for recently added microMIPS R6.
Consequently bare metal microMIPS R6 programs supporting UHI will not run.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
When a LWL, LWR, LDL or LDR instruction triggers a page fault, QEMU
currently reports the aligned address in CP0 BadVAddr, while the Windows
NT kernel expects the unaligned address.
This patch adds a byte access with the unaligned address at the
beginning of the LWL/LWR/LDL/LDR instructions to possibly trigger a page
fault and fill the QEMU TLB.
Cc: Leon Alrae <leon.alrae@imgtec.com>
Reported-by: Hervé Poussineau <hpoussin@reactos.org>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make use of CMPOP in floating-point compare instructions.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
