Get ready for PCI and other BT interfaces.
No functional changes, just split the code into generic BT code
and ISA-specific BT code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Get ready for PCI and other KCS interfaces.
No functional changes, just split the code into the generic KCS code
and the ISA-specific code.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Using the UUID that qemu generates probably isn't the best thing
to do, allow it to be passed in via properties, and use QemuUUID
for the type.
If the UUID is not set, return an unsupported command error. This
way we are not providing an all-zero (or randomly generated) GUID
to the IPMI user. This lets the host fall back to the other
method of using the get device id command to determind the BMC
being accessed.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Cédric Le Goater <clg@kaod.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
This is for IPMI, which will behave differently if the UUID is
not set.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Fam Zheng <famz@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
The IPMI BT tests had a race condition, if it receive an IPMI command
to enable interrupt, it would write the message to enable interrupts
after it wrote the command response. So the test code could
receive the command response and issue the next command before the
device handled the interrupt enable command, and thus no interrupt.
So send the message to enable interrupt before the command response.
Also add some sleeps to give qemu time to handle responses, there was
no delay before, and it could result in an invalid timeout.
And re-enable the tests, as hopefully they are fixed now.
Note that I was unable to reproduce this even with the instructions
Peter gave me, but hopefully this fixes the issue.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Add the watchdog pretimeout to the bits that cause an interrupt on attn.
Otherwise the user won't know.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
It wasn't returning the set timeout like it should have been.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The wrong logic was used for detection (so it wouldn't work at all)
and the wrong interface was used to inject the NMI if the detection
logic was correct.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This contains quite a few patches that I'd like to target for 4.2.
They're mostly emulation fixes for the sifive_u board, which now much
more closely matches the hardware and can therefor run the same fireware
as what gets loaded onto the board. Additional user-visible
improvements include:
* support for loading initrd files from the command line into Linux, via
/chosen/linux,initrd-{start,end} device tree nodes.
* The conversion of LOG_TRACE to trace events.
* The addition of clock DT nodes for our uart and ethernet.
This also includes some preliminary work for the H extension patches,
but does not include the H extension patches as I haven't had time to
review them yet.
This passes my OE boot test on 32-bit and 64-bit virt machines, as well
as a 64-bit upstream Linux boot on the sifive_u machine. It has been
fixed to actually pass "make check" this time.
Changes since v2 (never made it to the list):
* Sets the sifive_u machine default core count to 2 instead of 5.
Changes since v1 <20190910190513.21160-1-palmer@sifive.com>:
* Sets the sifive_u machine default core count to 5 instead of 1, as
it's impossible to have a single core sifive_u machine.
-----BEGIN PGP SIGNATURE-----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=yDSj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-4.2-sf1-v3' into staging
RISC-V Patches for the 4.2 Soft Freeze, Part 1, v3
This contains quite a few patches that I'd like to target for 4.2.
They're mostly emulation fixes for the sifive_u board, which now much
more closely matches the hardware and can therefor run the same fireware
as what gets loaded onto the board. Additional user-visible
improvements include:
* support for loading initrd files from the command line into Linux, via
/chosen/linux,initrd-{start,end} device tree nodes.
* The conversion of LOG_TRACE to trace events.
* The addition of clock DT nodes for our uart and ethernet.
This also includes some preliminary work for the H extension patches,
but does not include the H extension patches as I haven't had time to
review them yet.
This passes my OE boot test on 32-bit and 64-bit virt machines, as well
as a 64-bit upstream Linux boot on the sifive_u machine. It has been
fixed to actually pass "make check" this time.
Changes since v2 (never made it to the list):
* Sets the sifive_u machine default core count to 2 instead of 5.
Changes since v1 <20190910190513.21160-1-palmer@sifive.com>:
* Sets the sifive_u machine default core count to 5 instead of 1, as
it's impossible to have a single core sifive_u machine.
# gpg: Signature made Tue 17 Sep 2019 16:43:30 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.2-sf1-v3: (48 commits)
gdbstub: riscv: fix the fflags registers
target/riscv: Use TB_FLAGS_MSTATUS_FS for floating point
target/riscv: Fix mstatus dirty mask
target/riscv: Use both register name and ABI name
riscv: sifive_u: Update model and compatible strings in device tree
riscv: sifive_u: Remove handcrafted clock nodes for UART and ethernet
riscv: sifive_u: Fix broken GEM support
riscv: sifive_u: Instantiate OTP memory with a serial number
riscv: sifive: Implement a model for SiFive FU540 OTP
riscv: roms: Update default bios for sifive_u machine
riscv: sifive_u: Change UART node name in device tree
riscv: sifive_u: Update UART base addresses and IRQs
riscv: sifive_u: Reference PRCI clocks in UART and ethernet nodes
riscv: sifive_u: Add PRCI block to the SoC
riscv: sifive_u: Generate hfclk and rtcclk nodes
riscv: sifive: Implement PRCI model for FU540
riscv: sifive_u: Update PLIC hart topology configuration string
riscv: sifive_u: Update hart configuration to reflect the real FU540 SoC
riscv: sifive_u: Set the minimum number of cpus to 2
riscv: hart: Add a "hartid-base" property to RISC-V hart array
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This makes sure reads are confined to vga video memory.
v3: use uint32_t, fix cut+paste bug.
v2: fix ati_cursor_draw_line too.
Reported-by: xu hang <flier_m@outlook.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190917111441.27405-3-kraxel@redhat.com
Event format ending with newlines confuse the trace reports.
Forbid them.
Add a check to refuse new format added with trailing newline:
$ make
[...]
GEN hw/misc/trace.h
Traceback (most recent call last):
File "scripts/tracetool.py", line 152, in <module>
main(sys.argv)
File "scripts/tracetool.py", line 143, in main
events.extend(tracetool.read_events(fh, arg))
File "scripts/tracetool/__init__.py", line 367, in read_events
event = Event.build(line)
File "scripts/tracetool/__init__.py", line 281, in build
raise ValueError("Event format can not end with a newline character")
ValueError: Error at hw/misc/trace-events:121: Event format can not end with a newline character
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-3-philmd@redhat.com
Message-Id: <20190916095121.29506-3-philmd@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
While the tracing framework does not forbid trailing newline in
events format string, using them lead to confuse output.
It is the responsibility of the backend to properly end an event
line.
Some of our formats have trailing newlines, remove them.
[Fixed typo in commit description reported by Eric Blake
<eblake@redhat.com>
--Stefan]
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190916095121.29506-2-philmd@redhat.com
Message-Id: <20190916095121.29506-2-philmd@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This adds a trace point which prints every loaded image. This includes
bios/firmware/kernel/initradmdisk/pcirom.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190613050937.124903-1-aik@ozlabs.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
While debugging an application with GDB the following might happen:
(gdb) return
Make xxx return now? (y or n) y
Could not fetch register "fflags"; remote failure reply 'E14'
This is because riscv_gdb_get_fpu calls riscv_csrrw_debug with a wrong csr
number (8). It should use the csr_register_map in order to reach the
riscv_cpu_get_fflags callback.
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use the TB_FLAGS_MSTATUS_FS macro when enabling floating point in the tb
flags.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This is meant to mask off the hypervisor bits, but a typo caused it to
mask MPP instead.
Fixes: 1f0419cb04 ("target/riscv: Allow setting mstatus virtulisation bits")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use both the generic register name and ABI name for the general purpose
registers and floating point registers.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates model and compatible strings to use the same strings
as used in the Linux kernel device tree (hifive-unleashed-a00.dts).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
In the past we did not have a model for PRCI, hence two handcrafted
clock nodes ("/soc/ethclk" and "/soc/uartclk") were created for the
purpose of supplying hard-coded clock frequencies. But now since we
have added the PRCI support in QEMU, we don't need them any more.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present the GEM support in sifive_u machine is seriously broken.
The GEM block register base was set to a weird number (0x100900FC),
which for no way could work with the cadence_gem model in QEMU.
Not like other GEM variants, the FU540-specific GEM has a management
block to control 10/100/1000Mbps link speed changes, that is mapped
to 0x100a0000. We can simply map it into MMIO space without special
handling using create_unimplemented_device().
Update the GEM node compatible string to use the official name used
by the upstream Linux kernel, and add the management block reg base
& size to the <reg> property encoding.
Tested with upstream U-Boot and Linux kernel MACB drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds an OTP memory with a given serial number to the sifive_u
machine. With such support, the upstream U-Boot for sifive_fu540
boots out of the box on the sifive_u machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This implements a simple model for SiFive FU540 OTP (One-Time
Programmable) Memory interface, primarily for reading out the
stored serial number from the first 1 KiB of the 16 KiB OTP
memory reserved by SiFive for internal use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
With the support of heterogeneous harts and PRCI model, it's now
possible to use the OpenSBI image (PLATFORM=sifive/fu540) built
for the real hardware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
OpenSBI for fu540 does DT fix up (see fu540_modify_dt()) by updating
chosen "stdout-path" to point to "/soc/serial@...", and U-Boot will
use this information to locate the serial node and probe its driver.
However currently we generate the UART node name as "/soc/uart@...",
causing U-Boot fail to find the serial node in DT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This updates the UART base address and IRQs to match the hardware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Now that we have added a PRCI node, update existing UART and ethernet
nodes to reference PRCI as their clock sources, to keep in sync with
the Linux kernel device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Add PRCI mmio base address and size mappings to sifive_u machine,
and generate the corresponding device tree node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
To keep in sync with Linux kernel device tree, generate hfclk and
rtcclk nodes in the device tree, to be referenced by PRCI node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This adds a simple PRCI model for FU540 (sifive_u). It has different
register layout from the existing PRCI model for FE310 (sifive_e).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
With heterogeneous harts config, the PLIC hart topology configuration
string are "M,MS,.." because of the monitor hart #0.
Suggested-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The FU540-C000 includes a 64-bit E51 RISC-V core and four 64-bit U54
RISC-V cores. Currently the sifive_u machine only populates 4 U54
cores. Update the max cpu number to 5 to reflect the real hardware,
by creating 2 CPU clusters as containers for RISC-V hart arrays to
populate heterogeneous harts.
The cpu nodes in the generated DTS have been updated as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
It is not useful if we only have one management CPU.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[Palmer: Set default CPUs to 2]
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
At present each hart's hartid in a RISC-V hart array is assigned
the same value of its index in the hart array. But for a system
that has multiple hart arrays, this is not the case any more.
Add a new "hartid-base" property so that hartid number can be
assigned based on the property value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently riscv_harts_realize() creates all harts based on the
same cpu type given in the hart array property. With current
implementation it can only create homogeneous harts. Exact the
hart realize to a separate routine in preparation for supporting
multiple hart arrays.
Note the file header says the RISC-V hart array holds the state
of a heterogeneous array of RISC-V harts, which is not true.
Update the comment to mention homogeneous array of RISC-V harts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Group SiFive E and U cpu type defines into one header file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Use create_unimplemented_device() instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Currently the PRCI register block size is set to 0x8000, but in fact
0x1000 is enough, which is also what the manual says.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
For hfxosccfg register programming, SIFIVE_E_PRCI_HFXOSCCFG_RDY and
SIFIVE_E_PRCI_HFXOSCCFG_EN should be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Current SiFive PRCI model only works with sifive_e machine, as it
only emulates registers or PRCI block in the FE310 SoC.
Rename the file name to make it clear that it is for sifive_e.
This also prefix "sifive_e"/"SIFIVE_E" for all macros, variables
and functions.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
sifive_u machine does not use PRCI as of today. Remove the prci
header inclusion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Like other binary files, the executable attribute of opensbi images
should not be set.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The inclusion of "target/riscv/cpu.h" is unnecessary in various
sifive model drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Replace the call to hw_error() with qemu_log_mask(LOG_GUEST_ERROR,...)
in various sifive models.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
There is no need to return fdt at the end of create_fdt() because
it's already saved in s->fdt.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chih-Min Chao <chihmin.chao@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This removes "reg-names" and "riscv,max-priority" properties of the
PLIC node from device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jonathan Behrens <fintelia@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Some of the properties only have 1 cell so we should use
qemu_fdt_setprop_cell() instead of qemu_fdt_setprop_cells().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
