Commit 0f66998 makes -enable-fips conditional on Linux hosts but then uses it
unconditionally in vl.c.
Fix this by moving the fips handling to os-posix.c and adding a condition.
Cc: Paul Moore <pmoore@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
FIPS 140-2 requires disabling certain ciphers, including DES, which is used
by VNC to obscure passwords when they are sent over the network. The
solution for FIPS users is to disable the use of VNC password auth when the
host system is operating in FIPS compliance mode and the user has specified
'-enable-fips' on the QEMU command line.
This patch causes QEMU to emit a message to stderr when the host system is
running in FIPS mode and a VNC password was specified on the commend line.
If the system is not running in FIPS mode, or is running in FIPS mode but
VNC password authentication was not requested, QEMU operates normally.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
For command line options which permit '?' meaning 'please list the
permitted values', add support for 'help' as a synonym, by abstracting
the check out into a helper function.
This change means that in some cases where we were being lazy in
our string parsing, "?junk" will now be rejected as an invalid option
rather than being (undocumentedly) treated the same way as "?".
Update the documentation to use 'help' rather than '?', since '?'
is a shell metacharacter and thus prone to fail confusingly if there
is a single character filename in the current working directory and
the '?' has not been escaped. It's therefore better to steer users
towards 'help', though '?' is retained for backwards compatibility.
We do not, however, update the output of the system emulator's -help
(or any documentation autogenerated from the qemu-options.hx which
is the source of the -help text) because libvirt parses our -help
output and will break. At a later date when QEMU provides a better
interface so libvirt can avoid having to do this, we can update the
-help text too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* commit '6c779f22a93cc6e4565b940ef616e3efc5b50ba5':
Change ram_save_block to return -1 if there are no more changes
ram: save_live_setup() we don't need to synchronize the dirty bitmap.
ram: iterate phase
ram: save_live_complete() only do one loop
ram: save_live_setup() don't need to sent pages
savevm: split save_live into stage2 and stage3
savevm: split save_live_setup from save_live_state
savevm: introduce is_active method
savevm: Refactor cancel operation in its own operation
savevm: remove SaveLiveStateHandler
savevm: remove SaveSetParamsHandler
savevm: Live migration handlers register the struct directly
savevm: Use a struct to pass all handlers
The qemu_chr_new() function doesn't set errno on failure, so
don't print strerror(errno) on the error handling path when
dealing with the -serial, -parallel and -virtioconsole arguments.
This avoids nonsensical error messages like:
$ ./arm-softmmu/qemu-system-arm -serial wombat
qemu: could not open serial device 'wombat': Success
We also rephrase the message slightly to make it a little clearer
that we're expecting the name of a QEMU chr backend rather than
a host or guest serial/parallel/etc device.
Reported-by: Christian Müller <christian.mueller@heig-vd.ch>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Notice that the live migration users never unregister, so no problem
about freeing the ops structure.
Signed-off-by: Juan Quintela <quintela@redhat.com>
There are two producers of these hints: drive_init() on behalf of
-drive, and hd_geometry_guess().
The only consumer of the hint is hd_geometry_guess().
The callers of hd_geometry_guess() call it only when drive_init()
didn't set the hints. Therefore, drive_init()'s hints are never used.
Thus, hd_geometry_guess() only ever sees hints it produced itself in a
prior call. Only the first call computes something, subsequent calls
just repeat the first call's results. However, hd_geometry_guess() is
never called more than once: the device models don't, and the block
device is destroyed on unplug. Thus, dropping the repeat feature
doesn't break anything now.
If a block device wasn't destroyed on unplug and could be reused with
a new device, then repeating old results would be wrong. Thus,
dropping the repeat feature prevents future breakage.
This renders the hints unused. Purge them from the block layer.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently qemu outputs some low-level error in qemu-sockets.c
when failed to start vnc server.
eg. 'getaddrinfo(127.0.0.1,5902): Name or service not known'
Some libvirt users could not know what's happened with this
unclear error message. This patch added a more descriptive
error message.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Make qemu_find_file() check for the passed in name as a straight
pathname even if it doesn't have any path separator character in it.
This means that "-bios foo", "-dtb foo" etc will find a file 'foo'
in the current directory.
This removes an inconsistency with -kernel and -initrd, which both
accept plain filenames as meaning files in the current directory.
It's also less confusing for the user than an undocumented restriction
that "this option accepts a filename, except for the special case
where the filename you pass happens not to have a '/' in it, in
which case we'll ignore it."
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
QEMU exposes its version to the guest's hardware and in some cases that is wrong
(e.g. Windows prints messages about driver updates when you switch
the QEMU version).
There is a new field now on the struct QEmuMachine, hw_version, which may
contain the version that the specific machine should report. If that field is
set, then that machine will report that version to the guest.
Signed-off-by: Crístian Viana <vianac@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
<libutil.h> and <util.h> on *BSD (some have one, some another)
were #included just for openpty() declaration. The only file
where this function is actually used is qemu-char.c.
In vl.c and net/tap-bsd.c, none of functions declared in libutil.h
(login logout logwtmp timdomain openpty forkpty uu_lock realhostname
fparseln and a few others depending on version) are used.
Initially the code which is currently in qemu-char.c was in vl.c,
it has been removed into separate file in commit 0e82f34d07
Fri Oct 31 18:44:40 2008, but the #includes were left in vl.c.
So with vl.c, we just remove includes - libutil.h, util.h and
pty.h (which declares only openpty() and forkpty()) from there.
The code in net/tap-bsd.c, which come from net/tap.c, had this
commit 5281d757ef
Author: Mark McLoughlin <markmc@redhat.com>
Date: Thu Oct 22 17:49:07 2009 +0100
net: split all the tap code out into net/tap.c
Note this commit not only moved stuff out of net.c to net/tap.c,
but also rewrote large portions of the tap code, and added these
completely unnecessary #includes -- as usual, I question why such
a misleading commit messages are allowed.
Again, no functions defined in libutil.h or util.h on *BSD are
used by neither net/tap.c nor net/tap-bsd.c. Removing them.
And finally, the only real user for these #includes, qemu-char.c,
which actually uses openpty(). There, the #ifdef logic is wrong.
A GLIBC-based system has <pty.h>, even if it is a variant of *BSD.
So __GLIBC__ should be checked first, and instead of trying to
include <libutil.h> or <util.h>, we include <pty.h>. If it is not
GLIBC-based, we check for variations between <*util.h> as before.
This patch fixes build of qemu 1.1 on Debian/kFreebsd (well, one
of the two problems): it is a distribution with a FreeBSD kernel,
so it #defines at least __FreeBSD_kernel__, but since it is based
on GLIBC, it has <pty.h>, but current version does not have neither
<util.h> nor <libutil.h>, which the code tries to include 3 times
but uses only once.
Signed-off-By: Michael Tokarev <mjt@tls.msk.ru>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This commit converts qemu_opts_create() from qerror_report() to
error_set().
Currently, most calls to qemu_opts_create() can't fail, so most
callers don't need any changes.
The two cases where code checks for qemu_opts_create() erros are:
1. Initialization code in vl.c. All of them print their own
error messages directly to stderr, no need to pass the Error
object
2. The functions opts_parse(), qemu_opts_from_qdict() and
qemu_chr_parse_compat() make use of the error information and
they can be called from HMP or QMP. In this case, to allow for
incremental conversion, we propagate the error up using
qerror_report_err(), which keeps the QError semantics
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-By: Laszlo Ersek <lersek@redhat.com>
This is a partial revert of commits a369da5 (vga: improve VGA logic,
committed 2012-01-22) and c5bd4f3 (vga: fix -nodefaults -device VGA,
2012-01-24) which broke command-line option parsing in different ways.
Since commit a369da5 it has become impossible to specify a VGA device
entirely with QemuOpts-enabled options, i.e. without needing an explicit
"-vga none".
In addition, until commit c5bd4f3 -nodefaults would not disable the device
you specified with the legacy "-vga" option, independent of the order.
Since commit c5bd4f3 QEMU -nodefaults will override a previous -vga
option.
I did not reintroduce machine->no_vga. Boards can simply ignore the
vga_interface_type variable, and most will indeed do so.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use help functions in qemu-socket.c for tcp migration,
which already support ipv6 addresses.
Currently errp will be set to UNDEFINED_ERROR when migration fails,
qemu would output "migration failed: ...", and current user can
see a message("An undefined error has occurred") in monitor.
This patch changed tcp_start_outgoing_migration()/inet_connect()
/inet_connect_opts(), socket error would be passed back,
then current user can see a meaningful err message in monitor.
Qemu will exit if listening fails, so output socket error
to qemu stderr.
For IPv6 brackets must be mandatory if you require a port.
Referencing to RFC5952, the recommended format is:
[2312::8274]:5200
test status: Successed
listen side: qemu-kvm .... -incoming tcp:[2312::8274]:5200
client side: qemu-kvm ...
(qemu) migrate -d tcp:[2312::8274]:5200
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Function added to arch_init.c because it depends on arch-specific
settings.
Changes v1 -> v2:
- Move qemu_read_default_config_file() prototype to qemu-config.h
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
QEMU enters in this state when the guest suspends to ram (S3).
This is important so that HMP users and QMP clients can know that
the guest is suspended. QMP also has an event for this, but events
are not reliable and are limited (ie. a client can connect to QEMU
after the event has been emitted).
Having a different state for S3 brings a new issue, though. Every
device that doesn't run when the VM is stopped but wants to run
when the VM is suspended has to check for RUN_STATE_SUSPENDED
explicitly. This is the case for the keyboard and mouse devices,
for example.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
The idea behind qtest is pretty simple. Instead of executing a CPU via TCG or
KVM, rely on an external process to send events to the device model that the CPU
would normally generate.
qtest presents itself as an accelerator. In addition, a new option is added to
establish a qtest server (-qtest) that takes a character device. This is what
allows the external process to send CPU events to the device model.
qtest uses a simple line based protocol to send the events. Documentation of
that protocol is in qtest.c.
I considered reusing the monitor for this job. Adding interrupts would be a bit
difficult. In addition, logging would also be difficult.
qtest has extensive logging support. All protocol commands are logged with
time stamps using a new command line option (-qtest-log). Logging is important
since ultimately, this is a feature for debugging.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This will let people use backwards-compatible semantics for devices that
will be affected by the following patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix stupid copy&paste mistake at commit
ecf40beae7: I moved code around but kept
"optarg" on the cpu_list() call.
Reported-by: Jiri Denemark <jdenemar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
* sstabellini/saverestore-8:
xen: do not allocate RAM during INMIGRATE runstate
xen mapcache: check if memory region has moved.
xen: record physmap changes to xenstore
Set runstate to INMIGRATE earlier
Introduce "xen-save-devices-state"
cirrus_vga: do not reset videoram
Conflicts:
qapi-schema.json
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Set runstate to RUN_STATE_INMIGRATE as soon as we can on resume.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Commit 1b71f7c14f moved MODULE_INIT_QOM to
way before MODULE_INIT_MACHINE, thereby breaking assumptions made in
spice-core.c which registered both a type initializer and a machine
intializer.
This fix removes the type registration, and replaces it with calling
qemu_spice_init in vl.c after command line parsing (second pass) is
done, and after timers are armed, required by spice server.
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The constructors for QOM TYPE_INTERFACE were executed rather late in
vl.c's main(). Call them very early so that QOM can safely be used for
machines and CPUs.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
To properly load cpudefs using -readconfig, we have to call
cpudef_init() after finishing the command-line option handling.
Consequently, the handling of "-cpu ?" has to be done after the
command-line option handling loop, too.
Without this patch, "-readconfig configfile -cpu ?" fails to list the
CPU definitions read from 'configfile'.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If compiled with CONFIG_FDT, allow user to specify a device tree file using
the -dtb argument. If the machine supports it then the dtb will be loaded
into memory and passed to the kernel on boot.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[Peter Maydell: Use machine opt rather than global to pass dtb filename]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When creating an USB device the old way, there is no way to specify the
target bus. Thus the warning issued by usb_create makes no sense and
rather confuses our users.
Resolve this by passing a bus reference to the usbdevice_init handler
and letting those handlers forward it to usb_create.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix a bug (introduced in commit a0abe47) where a command line which
specified no machine arguments (either explicitly or implicitly via
-kernel &co) would result in a segfault because of a NULL pointer
returned from qemu_opts_find(qemu_find_opts("machine"), 0).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Send qmp events on suspend and wakeup so libvirt
has a chance to track the vm state.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch adds some infrastructure to handle suspend and resume to
qemu. First there are two functions to switch state and second there
is a suspend notifier:
* qemu_system_suspend_request is supposed to be called when the
guest asks for being be suspended, for example via ACPI.
* qemu_system_wakeup_request is supposed to be called on events
which should wake up the guest.
* qemu_register_suspend_notifier can be used to register a notifier
which will be called when the guest is suspended. Machine types
and device models can hook in there to modify state if needed.
* qemu_register_wakeup_notifier can be used to register a notifier
which will be called when the guest is woken up. Machine types
and device models can hook in there to modify state if needed.
* qemu_system_wakeup_enable can be used to enable/disable wakeup
events.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Stash away the option argument with add_device_config(), so we still
have its location when we get around to parsing it.
This doesn't improve any messages I can see just yet, but that'll
change shortly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
These are -bt, -serial, -virtcon, -parallel, -debugcon, -usbdevice.
Improves messages emitted via proper error reporting interfaces. For
instance:
$ qemu-system-x86_64 -nodefaults -S -usb -usbdevice net:vlan=xxx
qemu-system-x86_64: Parameter 'vlan' expects a number
becomes:
qemu-system-x86_64: -usbdevice net:vlan=xxx: Parameter 'vlan' expects a number
Many more remain unimproved, because they're fprintf()ed. The next
few commits will take care of that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Increase the width of the column used for the machine name in
the "-M ?" output from 10 to 20 spaces. This fixes the formatting
so it looks nice for architectures where a few of the machines
have overly long names. (Our current longest machine name is
"petalogix-s3adsp1800" with "realview-eb-mpcore" not far behind.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Make kernel, initrd, append be machine opts (ie -machine kernel=foo)
with the old plain command line arguments as legacy/convenience
equivalents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Notifiers do not need to access both ends of the list, and using
a QLIST also simplifies the API.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* stefanha/trivial-patches:
linux-user: brk() debugging
virtio: Remove unneeded g_free() check in virtio_cleanup()
net: remove extra spaces in help messages
fmopl: Fix typo in function name
vl.c: Fix typo in variable name
ide: fix compilation errors when DEBUG_IDE is set
cpu-exec.c: Correct comment about this file and indentation cleanup
CODING_STYLE: Clarify style for enum and function type names
linux-user: fail execve() if env/args too big
Make the "machine" option list use list merging, so that multiple
-machine arguments (and the -enable-kvm argument) all merge together
into a single list. Drop the calls to qemu_opts_reset() which meant
that only the last -machine or -enable-kvm option had any effect.
This fixes the bug where "-enable-kvm -machine foo" would ignore
the '-enable-kvm' option, and "-machine foo -enable-kvm" would
ignore the '-machine foo' option.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
* kwolf/for-anthony:
AHCI: Masking of IRQs actually masks them
sheepdog: fix co_recv coroutine context
AHCI: Fix port reset race
rewrite QEMU_BUILD_BUG_ON
qcow2: Keep unknown header extension when rewriting header
qcow2: Update whole header at once
vpc: Round up image size during fixed image creation
vpc: Add support for Fixed Disk type
iSCSI: add configuration variables for iSCSI
qemu-io: add write -z option for bdrv_co_write_zeroes
qed: add .bdrv_co_write_zeroes() support
qed: replace is_write with flags field
block: perform zero-detection during copy-on-read
block: add .bdrv_co_write_zeroes() interface
cutils: extract buffer_is_zero() from qemu-img.c
Replace device_init() with generalized type_init().
While at it, unify naming convention: type_init([$prefix_]register_types)
Also, type_init() is a function, so add preceding blank line where
necessary and don't put a semicolon after the closing brace.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: malc <av1474@comtv.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix a typo in a local variable name.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
This patch adds configuration variables for iSCSI to set
initiator-name to use when logging in to the target,
which type of header-digest to negotiate with the target
and username and password for CHAP authentication.
This allows specifying a initiator-name either from the command line
-iscsi initiator-name=iqn.2004-01.com.example:test
or from a configuration file included with -readconfig
[iscsi]
initiator-name = iqn.2004-01.com.example:test
header-digest = CRC32C|CRC32C-NONE|NONE-CRC32C|NONE
user = CHAP username
password = CHAP password
If you use several different targets, you can also configure this on a per
target basis by using a group name:
[iscsi "iqn.target.name"]
...
The configuration file can be read using -readconfig.
Example :
qemu-system-i386 -drive file=iscsi://127.0.0.1/iqn.ronnie.test/1
-readconfig iscsi.conf
Signed-off-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In some cases initializing the alarm timers can lead to non-negligable
overhead from programs that link against qemu-tool.o. At least,
setting a max-resolution WinMM alarm timer via mm_start_timer() (the
current default for Windows) can increase the "tick rate" on Windows
OSs and affect frequency scaling, and in the case of tools that run
in guest OSs such has qemu-ga, the impact can be fairly dramatic
(+20%/20% user/sys time on a core 2 processor was observed from an idle
Windows XP guest).
This patch doesn't address the issue directly (not sure what a good
solution would be for Windows, or what other situations it might be
noticeable), but it at least limits the scope of the issue to programs
that "opt-in" to using the main-loop.c functions by only enabling alarm
timers when qemu_init_main_loop() is called, which is already required
to make use of those facilities, so existing users shouldn't be
affected.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
So far we overwrite the machine options completely with defaults if no
accel=value is provided. More user friendly is to fill in only
unspecified options. The new qemu_opts_set_defaults enables this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Allow to configure the MC146818 RTC via the new lost tick policy
property and replace rtc_td_hack with this mechanism.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* qemu-kvm/uq/master:
kvm: Activate in-kernel irqchip support
kvm: x86: Add user space part for in-kernel IOAPIC
kvm: x86: Add user space part for in-kernel i8259
kvm: x86: Add user space part for in-kernel APIC
kvm: x86: Establish IRQ0 override control
kvm: Introduce core services for in-kernel irqchip support
memory: Introduce memory_region_init_reservation
ioapic: Factor out base class for KVM reuse
ioapic: Drop post-load irr initialization
i8259: Factor out base class for KVM reuse
i8259: Completely privatize PicState
apic: Open-code timer save/restore
apic: Factor out base class for KVM reuse
apic: Introduce apic_report_irq_delivered
apic: Inject external NMI events via LINT1
apic: Stop timer on reset
kvm: Move kvmclock into hw/kvm folder
msi: Generalize msix_supported to msi_supported
hyper-v: initialize Hyper-V CPUID leaves.
hyper-v: introduce Hyper-V support infrastructure.
Conflicts:
Makefile.target
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Improve VGA selection logic, push check for device availabilty to vl.c.
Create the devices at board level unconditionally.
Remove now unused pci_try_create*() functions.
Make PCI VGA devices optional.
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
KVM is forced to disable the IRQ0 override when we run with in-kernel
irqchip but without IRQ routing support of the kernel. Set the fwcfg
value correspondingly. This aligns us with qemu-kvm.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add option to use named socket for communicating between proxy helper
and qemu proxy FS. Access to socket can be given by using command line
options -u and -g.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Add new proxy filesystem driver to add root privilege to qemu process.
It needs a helper process to be started by root user.
Following command line can be used to utilize proxy filesystem driver
-virtfs proxy,id=<id>,mount_tag=<tag>,socket_fd=<socket-fd>
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
This remove all conditional code from common code path and
make opt validation a FSDriver callback.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
qemu-kvm passes numa/SRAT topology information for smp_cpus to SeaBIOS. However
SeaBIOS always expects to setup max_cpus number of SRAT cpu entries
(MaxCountCPUs variable in build_srat function of Seabios). When qemu-kvm runs
with smp_cpus != max_cpus (e.g. -smp 2,maxcpus=4), Seabios will mistakenly use
memory SRAT info for setting up CPU SRAT entries for the offline CPUs. Wrong
SRAT memory entries are also created. This breaks NUMA in a guest.
Fix by setting up SRAT info for max_cpus in qemu-kvm.
Signed-off-by: Vasilis Liaskovitis <vasilis.liaskovitis@profitbricks.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
since commit f9b29ca03 included in release 2.31 (docs below say 2.32 but
that is not correct) and onwards g_thread_init is deprecated and calling
it is not required:
http://developer.gnome.org/glib/unstable/glib-Deprecated-Thread-APIs.html#g-thread-init
g_thread_init has been deprecated since version 2.32 and should not be
used in newly-written code. This function is no longer necessary. The
GLib threading system is automatically initialized at the start of your
program.
Fixes bulid failure when warnings are treated as errors on fedora 17.
I only tested the change to vl.c, and copy pasted to the two other
locations (couldn't decide if a wrapper for calling g_thread_init is
uglier).
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The peripheral[-anon] containers are initialized lazily but since they sit on
sysbus, they can not be created after realize. This was causing an abort() to
occur during hotplug if no -device option was used.
This was spotted by qemu-test::device-add.sh
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Only print options in the help output that are accepted by our arch.
This is less confusing for users and also for other programs that
consume the help output.
The options affected are:
-g and -prom-env only displayed on PPC or SPARC
-win2k-hack, -rtc-td-hack, -no-fd-bootchk, -no-acpi, -no-hpet,
-acpitable, -smbios only displayed on i386
-semihosting only displayed on ARM, M68K or XTENSA
-old-param only displayed on ARM
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In vl.c and qemu-options.h we define macros and include qemu-options.def
in order to generate different content. Move the bulk of the def'ing and
undef'ing into a wrapper, this will make it cleaner when we add another
macro in the next patch.
AFAICS undefining GEN_DOCS services no purpose, but I've left it for now.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
In help() we do what boils down to:
printf("%s", "qemu");
This seems to be an artifact of be995c2764
("removed unused code"), which removed some ifdef'ery that used to print
a different name depending on CONFIG_SOFTMMU.
Instead print the actual program name, originally from argv[0].
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
strtosz_suffix() fails unless the size is followed by 0, whitespace or
','. Useless here, because we need to fail for any junk following the
size, even if it starts with whitespace or ','. Check manually.
Things like "-m 1024," are now caught.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
strtosz_suffix() fails unless the size is followed by 0, whitespace or
','. Useless here, because we need to fail for any junk following the
size, even if it starts with whitespace or ','. Check manually.
Things like
-smp 4 -numa "node,mem=1024,cpus=0-1" -numa "node,mem=1024 cpus=2-3"
are now caught. Before, the second -numa's argument was silently
interpreted as just "node,mem=1024".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
With -icount, The vm_clock is updated with help from TCG (it counts
instructions at 2^ICOUNT ns/instructions). With KVM, the instruction
count is not available so KVM cannot provide this help.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
machine defaults to find_default_machine(),
then gets overridden via -M and machine_parse().
If no -M is specified and find_default_machine() returns NULL
(when no machine compiled in), exit with an error.
Avoids a segfault when setting machine->max_cpus.
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
g_strdup() can't fail, remove assertion. Assert its argument can't be
null, because that's not obvious (add_boot_device_path() ensures it).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The caller of qemu_timedate_diff() does not expect that tm it passes to
the function will be modified, but mktime() is destructive and modifies
its argument. Pass a copy of tm to it and set tm_isdst so that mktime()
will not rely on it since its value may be outdated.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
GThread-ERROR **: GThread system may only be initialized once.
aborting...
Making the g_thread_init() call in vl.c conditional resolves an abort on
Mac OS X, where coroutine-gthread.c seems to call it before vl.c.
Reported-by: Juan Pineda <juan@logician.com>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Cc: Daniel P. Berrange <berrange@redhat.com>
This patch create a synthetic file system with mount tag
v_synth when -virtfs_synth command line option is specified
in qemu. The synthetic file system can be mounted in guest
using 9p using the below command line
mount -t 9p -oversion=9p2000.L,trans=virtio v_synth <mountpint>
Synthetic file system enabled different qemu subsystem to register
callbacks for read and write events from guest. The subsystem
can create directories and files in the synthetic file system as show
in ex below
qemu_v9fs_synth_mkdir(NULL, 0777, "test2", &node);
qemu_v9fs_synth_add_file(node, 0777, "testfile",
my_test_read, NULL, NULL);
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
A new fsdev parameter "readonly" is introduced to control accessing 9p export.
"readonly" can be used to specify the access type. By default "rw" access
is given to 9p export.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Previous commits dropped most qobjects usage from qemu modules
(now they are a low level interface used by the QAPI). However,
some modules still include the qemu-objects.h header file.
This commit drops qemu-objects.h from some of those modules
and includes qjson.h instead, which is what they actually need.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
It should be a matter of allowing the transition POSTMIGRATE ->
FINISH_MIGRATE, but it turns out that the VM won't do the
transition the second time because it's already stopped.
So this commit also adds vm_stop_force_state() which performs
the transition even if the VM is already stopped.
While there also allow other states to migrate.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The user may already have paused the VM before starting the
migration process. If s/he does that, then the state will be
'paused' when we finish the migration process. In that case
we want to transition from 'paused' to 'postmigrate' as the
latter is now the real reason why the VM is stopped.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
We flush coalesced MMIO in the device models now, and VNC - for which
this was once introduced - is also fine without it as it has its own
refresh timer.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This is conceptually cleaner and will allow us to drop the nographic
timer. Moreover, it will be mandatory to fully exploit future per-device
coalesced MMIO rings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
writeout=immediate implies the after pwritev we do a sync_file_range.
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Please, note that the RunState type as defined in sysemu.h and its
runstate_as_string() function are being dropped in favor of the
RunState type generated by the QAPI.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Next commit will convert the query-status command to use the
RunState type as generated by the QAPI.
In order to "transparently" replace the current enum by the QAPI
one, we have to make some changes to some enum values.
As the changes are simple renames, I'll do them in one shot. The
changes are:
- Rename the prefix from RSTATE_ to RUN_STATE_
- RUN_STATE_SAVEVM to RUN_STATE_SAVE_VM
- RUN_STATE_IN_MIGRATE to RUN_STATE_INMIGRATE
- RUN_STATE_PANICKED to RUN_STATE_INTERNAL_ERROR
- RUN_STATE_POST_MIGRATE to RUN_STATE_POSTMIGRATE
- RUN_STATE_PRE_LAUNCH to RUN_STATE_PRELAUNCH
- RUN_STATE_PRE_MIGRATE to RUN_STATE_PREMIGRATE
- RUN_STATE_RESTORE to RUN_STATE_RESTORE_VM
- RUN_STATE_PRE_MIGRATE to RUN_STATE_FINISH_MIGRATE
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The QAPI framework won't generate it, so we need to get rid of it.
In order to do that, this commit makes RSTATE_PRE_LAUNCH the initial
state and change qemu_vmstop_requested() to use RSTATE_MAX.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The stop reason is returned in the RunState argument. This is a
preparation for a future commit which will convert the query-status
command to the QAPI.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
On signals such as SIGTERM qemu should exit instead of just stopping the VM
even with -no-shutdown.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This new key reports the current VM status to clients. Please, check
the documentation being added in this commit for more details.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
We have two states where issuing cont before system_reset can
cause problems: RSTATE_SHUTDOWN (when -no-shutdown is used) and
RSTATE_PANICKED (which only happens with kvm).
This commit fixes that by doing the following when state is
RSTATE_SHUTDOWN or RSTATE_PANICKED:
1. returning an error to the user/client if cont is issued
2. automatically transition to RSTATE_PAUSED during system_reset
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Test against RSTATE_IN_MIGRATE instead.
Please, note that the RSTATE_IN_MIGRATE state is only set when all the
initial VM setup is done, while 'incoming_expected' was set right in
the beginning when parsing command-line options. Shouldn't be a problem
as far as I could check.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This commit could have been folded with the previous one, however
doing it separately will allow for easy bisect and revert if needed.
Checking and testing all valid transitions wasn't trivial, chances
are this will need broader testing to become more stable.
This is a transition table as suggested by Lluís Vilanova.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Currently, only vm_start() and vm_stop() change the VM state.
That's, the state is only changed when starting or stopping the VM.
This commit adds the runstate_set() function, which makes it possible
to also do state transitions when the VM is stopped or running.
Additional states are also added and the current state is stored.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Today, when notifying a VM state change with vm_state_notify(),
we pass a VMSTOP macro as the 'reason' argument. This is not ideal
because the VMSTOP macros tell why qemu stopped and not exactly
what the current VM state is.
One example to demonstrate this problem is that vm_start() calls
vm_state_notify() with reason=0, which turns out to be VMSTOP_USER.
This commit fixes that by replacing the VMSTOP macros with a proper
state type called RunState.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Initialize glib threads unconditionally in main() instead
of using g_thread_get_initialized in the 9p code.
Fixes a build failure on RHEL-5, which ships glib 2.12.
g_thread_get_initialized was added in 2.20.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Enabling the I/O thread by default seems like an important part of declaring
1.0. Besides allowing true SMP support with KVM, the I/O thread means that the
TCG VCPU doesn't have to multiplex itself with the I/O dispatch routines which
currently requires a (racey) signal based alarm system.
I know there have been concerns about performance. I think so far the ones that
have come up (virtio-net) are most likely due to secondary reasons like
decreased batching.
I think we ought to force enabling I/O thread early in 1.0 development and
commit to resolving any lingering issues.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows GSources to be used to register callback events in QEMU. This is
useful as it allows us to take greater advantage of glib and also because it
allows us to write code that is more easily testable outside of QEMU since we
can make use of glib's main loop in unit tests.
All new code should use glib's callback mechanisms for registering fd events
which are very well documented at:
http://developer.gnome.org/glib/stable/glib-The-Main-Event-Loop.html
And:
http://developer.gnome.org/gio/stable/
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The "-trace events" argument can be used to provide a file with a list of trace
event names that will be enabled prior to starting execution, thus providing
early tracing.
This saves the user from manually toggling event states through the monitor
interface or whichever backend-specific interface.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
A default implementation for backend-specific routines is provided in
"trace/default.c", which backends can override by setting "trace_default=no" in
"configure".
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Provides a more hierarchical view of the variable domain.
Also adds the CONFIG_TRACE_* variables for all backends.
[Stefan added missing 'test' in stap if statement]
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Polling until select returns empty fdsets helps to reduce the switches
between iothread and vcpus. The benefit of this patch is best visible
when running an SMP guest on an SMP host in emulation mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
If we call select without a timeout, it's more efficient to keep the
global mutex locked as we may otherwise just play ping pong with a
vcpu thread contending for it. This is particularly important for TCG
mode where we run in lock-step with the vcpu thread.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
code_gen_alloc depends on it, and that is now called earlier via
configure_accelerator.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Do not allocate TCG-only resources like the translation buffer when
running over KVM or XEN. Saves a "few" bytes in the qemu address space
and is also conceptually cleaner.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This allows to specify -machine options without setting an explicit
machine type. We will pick the default machine in this case. Requesting
the list of available machines is still possible via '-machine ?' e.g.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Added options to let qemu transfer two configuration files to bios:
"bootsplash.bmp" and "etc/boot-menu-wait", which could be specified by command
-boot splash=P,splash-time=T
P is jpg/bmp file name or an absolute path, T have a max value of 0xffff, unit
is ms. With these two options, if user invoke qemu with menu=on option, then
a splash picture would be showed in a given time. For example:
qemu -boot menu=on,splash=/root/boot.bmp,splash-time=5000
would make boot.bmp shown as a brand with 5 seconds in the booting up process.
This feature need the new seabios's support, which could be got from git.
Signed-off-by: Wayne Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
As a Xen guest can have more than 2GB of RAM on a 32bit host, we move
the conditions after than we now if we run one Xen or not.
[agraf] separate xen branch from ram_size check
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows to pass additional information to the notifier callback
which is useful if sender and receiver do not share any other distinct
data structure.
Will be used first for the clock reset notifier.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Daniel P. Berrange sent a libvirt's patch to support
reboots with the QEMU driver. He implements it in
json model like this:
1. add -no-shutdown in the qemu's option:
qemu -no-shutdown xxxx
2. shutdown the vm by monitor command system_powerdown
3. wait for shutdown event
4. reset the vm by monitor command system_reset
no_shutdown will be reset to 0 if the vm is powered down.
We only can reboot the vm once.
If no_shutdown is not reset to 0, we can reboot the vm
many times.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
[I've sent this patch couple of months ago and noticed it
didn't make it's way in - so I'm sending it again]
It is possible to create CPU-less NUMA nodes, node amount shouldn't be
limited by amount of CPUs.
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Acked-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
-machine somehow suggests that it selects the machine, but it doesn't.
Fix that before this command is set in stone.
Actually, -machine should supersede -M and allow to introduce arbitrary
per-machine options to the command line. That will change the internal
realization again, but we will be able to keep the user interface
stable.
Tested-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Until now, pxa2xx_lcd only supported 90deg rotation, but
some machines (for example Zipit Z2) needs 270deg rotation.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
This allows qemu_system_reset to be issued silently for internal
purposes, ie. without sending out a monitor event. Convert the system
reset after startup to the silent mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
BeOS and Haiku on i386 use long for 32-bit types, including pid_t.
Using %d with pid_t therefore results in a warning.
Unfortunately POSIX:2008 does not define a PRId* string for pid_t.
In some places pid_t was previously casted to long and %ld hardcoded.
The predecessor of this patch added another upcast for the simpletrace
filename but was not applied to date.
Since new uses of pid_t with %d keep creeping in, let's instead define
an OS-dependent format string and use that consistently.
Cc: Stefan Hajnoczi <stefanha@gmail.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Ingo Weinhold <ingo_weinhold@gmx.de>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andreas Färber <andreas.faerber@web.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add command line support for logging to a location other than /tmp/qemu.log.
With logging enabled (command line option -d), the log is written to
the hard-coded path /tmp/qemu.log. This patch adds support for writing
the log to a different location by passing the -D option.
Signed-off-by: Matthew Fernandez <matthew.fernandez@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Switch no_user off and make it suppress the default VGA.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Commit 85097db6 changed the timing when kvm_allowed is set until after
kvm is initialized. During initialization, the ioeventfd initialization code
checks kvm_enabled() and after this change, ioeventfd is effectively disabled.
This causes a significant regression in performance.
Fix this by setting kvm_allowed before calling init.
Reported-by: Khoa Huynh <khoa@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
ide-hd has to suppress the default CD-ROM, or else you can't put one
on secondary master without -nodefaults.
Unlike legacy scsi-disk, scsi-cd suppresses default CD-ROM.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Introduce two functions qemu_shutdown_requested_get and
qemu_reset_requested_get to get the value of shutdown/reset_requested
without reset it.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The xenpv machine use the common init function.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
With this new field, we can specified which accelerator use to run the
machine, if the accelerator is not already specified by either a
configuration file or the command line options.
Currently, the only use will be made in the xenfv machine.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This option gives the ability to switch one "accelerator" like kvm, xen
or the default one tcg. We can specify more than one accelerator by
separate them by a colon. QEMU will try each one and use the first whose
works.
So,
./qemu -machine accel=xen:kvm:tcg
which would try Xen support first, then KVM and finally TCG if none of
the other works.
By default, QEMU will use TCG. But we can specify another default in the
global configuration file.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The -virtfs option creates an fsdev representing the pass-through file
system and a guest-visible virtio-9p-pci device that can access this
file system. This patch replaces the string manipulation used to build
and reparse option lists with direct QemuOpts calls. Removing the
string manipulation code makes it easier to maintain and less error
prone.
An error message is also updated to use "mount_tag" instead of
"mnt_tag".
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
This fixes the problem when qemu continues even if -drive specification
is somehow invalid, resulting in a mess. Applicable for both current
master and for stable-0.14 (and the same issue exist 0.13 and 0.12 too).
The prob can actually be seriuos: when you start guest with two drives
and make an error in the specification of one of them, and the guest
has something like a raid array on the two drives, guest may start failing
that array or kick "missing" drives which may result in a mess - this is
what actually happened to me, I did't want a resync at all, and a resync
resulted in re-writing (and allocating) a 4TB virtual drive I used for
testing, which in turn resulted in my filesystem filling up and whole
thing failing badly. Yes it was just testing VM, I experimented with
larger raid arrays, but the end result was quite, well, unexpected.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We have two different virtio buses: pci and s390. The abstraction path
taken in qemu is to have generic aliases for each device type in the
architecture specific qdev devices.
So let's make use of these aliases whenever we can and define them
whenever we can.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
SDL library initialization mangles signal handlers, so QEMU should
register them after initializing SDL. This was the case before and code
even have a comment about that. Fix it to be so again.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Tidy up the message printed when qemu exits due to a signal, so that
it's clearer where the message is coming from and that it's not just
stray debug output.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Currently when rogue script kills QEMU process (using TERM/INT/HUP
signal) it looks indistinguishable from system shutdown. Lets report
that QEMU was killed and leave some clues about the killer identity.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Fix a compilation failure if CONFIG_SDL isn't defined (gcc complained
that the label 'invalid_display' wasn't used).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
New option -display none. This option differs from -nographic by not
trying to take control of stdio etc. but instead behaves as if a
graphics display is enabled, except that it doesn't show one.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch introduces a -display argument which consolidates the
setting of the display mode. Valid options are:
sdl/curses/default
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This was done with:
sed -i '/get_clock\>.*rt_clock/s/get_clock\>/get_clock_ms/' \
$(git grep -l 'get_clock\>.*rt_clock' )
sed -i '/new_timer\>.*rt_clock/s/new_timer\>/new_timer_ms/' \
$(git grep -l 'new_timer\>.*rt_clock' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
User emulator builds do not have error_report() so it should not be used
by simpletrace.c. In fact, error reporting inside simpletrace.c is
inappropriate and should be done by the caller instead.
This patch moves st_init() error reporting out to its caller,
vl.c:main().
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This is required to support keeping VCPU states across a system reset.
If we do not read the current state before the reset,
cpu_synchronize_all_post_reset may write back incorrect state
information.
The first user of this will be MCE MSR synchronization which currently
works around the missing cpu_synchronize_all_states.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Trace events outside the global mutex cannot be used with the simple
trace backend since it is not thread-safe. There is no check to prevent
them being enabled so people sometimes learn this the hard way.
This patch restructures the simple trace backend with a ring buffer
suitable for multiple concurrent writers. A writeout thread empties the
trace buffer when threshold fill levels are reached. Should the
writeout thread be unable to keep up with trace generation, records will
simply be dropped.
Each time events are dropped a special record is written to the trace
file indicating how many events were dropped. The event ID is
0xfffffffffffffffe and its signature is dropped(uint32_t count).
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
To prepare splitting up KVM and TCG CPU entry/exit, move the debug
exception into cpus.c and invoke cpu_handle_debug_exception on return
from qemu_cpu_exec.
This also allows to clean up the debug request signaling: We can assign
the job of informing main-loop to qemu_system_debug_request and stop the
calling cpu directly in cpu_handle_debug_exception. That means a debug
stop will now only be signaled via debug_requested and not additionally
via vmstop_requested.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of fiddling with debug_requested and vmstop_requested directly,
introduce qemu_system_debug_request and turn qemu_system_vmstop_request
into a public interface. This aligns those services with exiting ones in
vl.c.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Define and use dedicated constants for vm_stop reasons, they actually
have nothing to do with the EXCP_* defines used so far. At this chance,
specify more detailed reasons so that VM state change handlers can
evaluate them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
First of all, vm_can_run is a misnomer, it actually means "no request
pending". Moreover, there is no need to check all pending requests
twice, the first time via the inner loop check and then again when
actually processing the requests. We can simply remove the inner loop
and do the checks directly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If there is any pending request that requires us to leave the inner loop
if main_loop, makes sure we do this as soon as possible by enforcing
non-blocking IO processing.
At this change, move variable definitions out of the inner loop to
improve readability.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
A pending vmstop request is also a reason to leave the inner main loop.
So far we ignored it, and pending stop requests issued over VCPU threads
were simply ignored.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If some I/O operation ends up calling qemu_system_reset_request in VCPU
context, we record this and inform the io-thread, but we do not
terminate the VCPU loop. This can lead to fairly unexpected behavior if
the triggering reset operation is supposed to work synchronously.
Fix this for TCG (when run in deterministic I/O mode) by setting the
VCPU on stop and issuing a cpu_exit. KVM requires some more work on its
VCPU loop.
[ ported from qemu-kvm ]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Also use qemu_strdup() instead of strdup() in bootindex code.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Watch this:
(qemu) drive_add 0 if=none
(qemu) info block
none0: type=hd removable=0 [not inserted]
(qemu) drive_del none0
Segmentation fault (core dumped)
add_init_drive() is confused about drive_init()'s failure modes, and
cleans up when it shouldn't. This leaves the DriveInfo with member
opts dangling. drive_del attempts to free it, and dies.
drive_init() behaves as follows:
* If it created a drive with media, it returns its DriveInfo.
* If it created a drive without media, it clears *fatal_error and
returns NULL.
* If it couldn't create a drive, it sets *fatal_error and returns
NULL.
Of its three callers:
* drive_init_func() is correct.
* usb_msd_init() assumes drive_init() failed when it returns NULL.
This is correct only because it always passes option "file", and
"drive without media" can't happen then.
* add_init_drive() assumes drive_init() failed when it returns NULL.
This is incorrect.
Clean up drive_init() to return NULL on failure and only on failure.
Drop its parameter fatal_error.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Let the callers build the optstr. Only one wants to. All the others
become simpler, because they don't have to worry about escaping '%'.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We silently ignore multiple definitions for the same drive:
$ qemu-system-x86_64 -nodefaults -vnc :1 -S -monitor stdio -drive if=ide,index=1,file=tmp.qcow2 -drive if=ide,index=1,file=nonexistant
QEMU 0.13.50 monitor - type 'help' for more information
(qemu) info block
ide0-hd1: type=hd removable=0 file=tmp.qcow2 backing_file=tmp.img ro=0 drv=qcow2 encrypted=0
With if=none, this can become quite confusing:
$ qemu-system-x86_64 -nodefaults -vnc :1 -S -monitor stdio -drive if=none,index=1,file=tmp.qcow2,id=eins -drive if=none,index=1,file=nonexistant,id=zwei -device ide-drive,drive=eins -device ide-drive,drive=zwei
qemu-system-x86_64: -device ide-drive,drive=zwei: Property 'ide-drive.drive' can't find value 'zwei'
The second -device fails, because it refers to drive zwei, which got
silently ignored.
Make multiple drive definitions fail cleanly.
Unfortunately, there's code that relies on multiple drive definitions
being silently ignored: main() merrily adds default drives even when
the user already defined these drives. Fix that up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before, type & index were hidden in printf-like fmt, ... parameters,
which get expanded into an option string. Rather inconvenient for
uses later in this series.
New IF_DEFAULT to ask for the machine's default interface. Before,
that was done by having no option "if" in the option string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
strtosz() needs to return a 64 bit type even on 32 bit
architectures. Otherwise qemu-img will fail to create disk
images >= 2GB
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Stefan Weil reported the regression caused by
ec990eb622 as follows
> The second regression also occurs with MIPS malta.
> Networking no longer works with the default pcnet nic.
>
> This is caused because the reset function for pcnet is no
> longer called during system boot. The result in an invalid
> mac address (all zero) and a non-working nic.
>
> For this second regression I still have no simple solution.
> Of course mips_malta.c should be converted to qdev which
> would fix both problems (but only for malta system emulation).
The issue is, it is assumed that all qbuses, qdeves are under
main_system_bus. But there are qbuses whose parent is NULL. So it
is necessary to trigger reset for those qbuses.
(On the other hand, if NULL is passed to qdev_create(), its parent bus
is main_system_bus.)
Ideally those buses should be moved under bus controller
device which is qdev. But it's not done yet.
So register qbus reset handler for qbus whose parent is NULL.
Reported-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid the warning below by using snprintf:
../libhw64/vl.o(.text+0x78d4): In function `get_boot_devices_list':
/src/qemu/vl.c:763: warning: sprintf() is often misused, please use snprintf()
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Action that depends on fully initialized device model should register
with this notifier chain.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If bootindex is specified on command line a string that describes device
in firmware readable way is added into sorted list. Later this list will
be passed into firmware to control boot order.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
qxl is a paravirtual graphics card. The qxl device is the bridge
between the guest and the spice server (aka libspice-server). The
spice server will send the rendering commands to the spice client, which
will actually render them.
The spice server is also able to render locally, which is done in case
the guest wants read something from video memory. Local rendering is
also used to support display over vnc and sdl.
qxl is activated using "-vga qxl". qxl supports multihead, additional
cards can be added via '-device qxl".
[ v2: add copyright to files ]
[ v2: use qemu-common.h for standard includes ]
[ v2: create separate qxl-vga device for primary ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch changes the reset handling so that qdev has no knowledge of the
global system reset. Instead, a new bus/device level function is introduced
that allows all devices/buses on the bus/device to be reset using a depth
first transversal.
N.B. we have to expose the implicit system bus because we have various hacks
that result in an implicit system bus existing. Instead, we ought to have an
explicitly created system bus that we can trigger reset from. That's a topic
for a future patch though.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VM state change notifications are invoked from vm_start()/vm_stop().
Trace these state changes so we can reason about the state of the VM
from trace output.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since commit 4bed983730 an .fd_read()
handler that deletes its IOHandler is exposed to .fd_write() being
called on the deleted IOHandler.
This patch fixes deletion so that .fd_read() and .fd_write() are never
called on an IOHandler that is marked for deletion.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
strtosz() returns -1 on error. It now supports human unit formats in
eg. 1.0G, with better error handling.
The following suffixes are supported:
B/b = bytes
K/k = KB
M/m = MB
G/g = GB
T/t = TB
This patch changes -numa and -m input to use strtosz().
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move timer init functions to a new file, qemu-timer-common.c. Make other
critical timer functions inlined to preserve performance in
qemu-timer.c, also move muldiv64() (used by the inline functions)
to qemu-timer.h.
Adjust block/raw-posix.c and simpletrace.c to use get_clock() directly.
Remove a similar/duplicate definition in qemu-tool.c.
Adjust hw/omap_clk.c to include qemu-timer.h because muldiv64() is used
there.
After this change, tracing can be used also for user code and
simpletrace on Win32.
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Acked-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Expaned '-mon' arg to allow a 'pretty=on' flag. This makes the
monitor pretty print its replies to easy human debugging / reading
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
vl.c has a Sun-specific hack to supply a prototype for madvise(),
but the call site has apparently moved to arch_init.c.
Haiku doesn't implement madvise() in favor of posix_madvise().
OpenBSD and Solaris 10 don't implement posix_madvise() but madvise().
MinGW implements neither.
Check for madvise() and posix_madvise() in configure and supply qemu_madvise()
as wrapper. Prefer madvise() over posix_madvise() due to flag availability.
Convert all callers to use qemu_madvise() and QEMU_MADV_*.
Note that on Solaris the warning is fixed by moving the madvise() prototype,
not by qemu_madvise() itself. It helps with porting though, and it simplifies
most call sites.
v7 -> v8:
* Some versions of MinGW have no sys/mman.h header. Reported by Blue Swirl.
v6 -> v7:
* Adopt madvise() rather than posix_madvise() semantics for returning errors.
* Use EINVAL in place of ENOTSUP.
v5 -> v6:
* Replace two leftover instances of POSIX_MADV_NORMAL with QEMU_MADV_INVALID.
Spotted by Blue Swirl.
v4 -> v5:
* Introduce QEMU_MADV_INVALID, suggested by Alexander Graf.
Note that this relies on -1 not being a valid advice value.
v3 -> v4:
* Eliminate #ifdefs at qemu_advise() call sites. Requested by Blue Swirl.
This will currently break the check in kvm-all.c by calling madvise() with
a supported flag, which will not fail. Ideas/patches welcome.
v2 -> v3:
* Reuse the *_MADV_* defines for QEMU_MADV_*. Suggested by Alexander Graf.
* Add configure check for madvise(), too.
Add defines to Makefile, not QEMU_CFLAGS.
Convert all callers, untested. Suggested by Blue Swirl.
* Keep Solaris' madvise() prototype around. Pointed out by Alexander Graf.
* Display configure check results.
v1 -> v2:
* Don't rely on posix_madvise() availability, add qemu_madvise().
Suggested by Blue Swirl.
Signed-off-by: Andreas Färber <afaerber@opensolaris.org>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
With that patch applied you'll actually see the guests screen in the
spice client. This does *not* bring qxl and full spice support though.
This is basically the qxl vga mode made more generic, so it plays
together with any qemu-emulated gfx card. You can display stdvga or
cirrus via spice client. You can have both vnc and spice enabled and
clients connected at the same time.
Add -spice command line switch. Has support setting passwd and port for
now. With this patch applied the spice client can successfully connect
to qemu. You can't do anything useful yet though.
