By specifying the silicon revision we select the appropriate reset
values for the SoC.
Additionally, expose hardware strapping properties aliasing those
provided by the SCU for board-specific configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1466744305-23163-3-git-send-email-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SCU is a collection of chip-level control registers that manage the
various functions supported by ASPEED SoCs. Typically the bits control
interactions with clocks, external hardware or reset behaviour, and we
can largly take a hands-off approach to reads and writes.
Firmware makes heavy use of the state to determine how to boot, but the
reset values vary from SoC to SoC (eg AST2400 vs AST2500). A qdev
property is exposed so that the integrating SoC model can configure the
silicon revision, which in-turn selects the appropriate reset values.
Further qdev properties are exposed so the board model can configure the
board-dependent hardware strapping.
Almost all provided AST2400 reset values are specified by the datasheet.
The notable exception is SOC_SCRATCH1, where we mark the DRAM as
successfully initialised to avoid unnecessary dark corners in the SoC's
u-boot support.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1466744305-23163-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop unnecessary inttypes.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cadence GEM data sheet says:
"Wrap - marks last descriptor in transmit buffer descriptor list. This
can be set for any buffer within the frame."
which seems to imply that when the wrap bit is set so is the last bit.
Previously if the wrap bit is set, but the last is not then QEMU will
enter an infinite loop.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: eb23f15c67989ea6a53609dc66568399dadf52a7.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A guest can write zero to the DMACFG resulting in an infinite loop when
it reaches the while(bytes_to_copy) loop.
To avoid this issue enforce a minimum size for the RX buffer. Hardware
does not have this enforcement and relies on the guest to set a non-zero
value.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reported-by: P J P <ppandit@redhat.com>
Message-id: 84bb1c391b833275da3f573d4972920cea34c188.1466539342.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If qemu_chr_fe_write() returns an error (represented by a negative
number) we should skip incrementing the count and initiating a
memmove().
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 667e5dc534d33338fcfc2471e5aa32fe7cbd13dc.1466546703.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are spotted by coverity 1356936 and 1356937.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
struct CPUCore uses 'id' suffix in the property name. As docs for
query-hotpluggable-cpus state that the cpu core properties should be
passed back to device_add by management in case new members are added
and thus the names for the fields should be kept in sync.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
[dwg: Removed a duplicated word in comment]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ppce500_spin.c uses SPR_PIR to initialize the spin table, however on
Book E processors the correct SPR is SPR_BOOKE_PIR.
Signed-off-by: Aaron Larson <alarson@ddci.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
All users have been converted to the new ioevent callbacks.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert to the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convert to new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the new interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Have vhost and dataplane use the new api for transports that
have been converted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a set of ioeventfd callbacks on the virtio-bus level
that can be implemented by the individual transports. At the
virtio-bus level, do common handling for host notifiers (which
is actually most of it).
Two things of note:
- When setting the host notifier, we only switch from/to the
generic ioeventfd handler. This fixes a latent bug where we
had no ioeventfd assigned for a certain window.
- We always iterate over all possible virtio queues, even though
ccw (currently) has a lower limit. It does not really matter
here.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCMachineState.node_cpu was used for mapping APIC ID
to numa node id as CPU entries in SRAT used to be
built on sparse APIC ID bitmap (up to apic_id_limit).
However since commit
5803fce pc: acpi: SRAT: create only valid processor lapic entries
CPU entries in SRAT aren't build using apic bitmap
but using 0..maxcpus index instead which is also used
for creating numa_info[x].node_cpu map.
So instead of doing useless intermediate conversion from
1. node by cpu index -> node by apic id
i.e. numa_info[x].node_cpu -> PCMachineState.node_cpu
2. apic id -> srat entry PMX
PCMachineState.node_cpu[apic id] -> PMX value
use numa_info[x].node_cpu map directly like ARM does and do
1. numa_info[x].node_cpu -> PMX value using index
in range 0..maxcpus
and drop not necessary PCMachineState.node_cpu and related
code.
That also removes the last (not counting legacy hotplug)
dependency of ACPI code on apic_id_limit and need to allocate
huge sparse PCMachineState.node_cpu array in case of 32-bit
APIC IDs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For compatibility reasons PC/Q35 will start with legacy
CPU hotplug interface by default but with new CPU hotplug
AML code since 2.7 machine type. That way legacy firmware
that doesn't use QEMU generated ACPI tables will be
able to continue using legacy CPU hotplug interface.
While new machine type, with firmware supporting QEMU
provided ACPI tables, will generate new CPU hotplug AML,
which will switch to new CPU hotplug interface when
guest OS executes its _INI method on ACPI tables
loading.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds HW and AML parts for CPU_Device._OST method
handling to allow OSPM reports status of hot-(un)plug
operation.
And extends QMP command query-acpi-ospm-status to report
CPU's OST info along with already reported PC-DIMM devices.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-remove and
corresponding AML methods to request and eject a CPU with
necessary hotplug callbacks in pc,piix4,ich9 code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds hw registers needed for handling CPU hot-add and
corresponding AML methods to handle hot-add events on
guest side.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add madt_cpu callback to AcpiDeviceIfClass and use
it for generating LAPIC MADT entries for CPUs.
Later it will be used for generating x2APIC
entries in case of more than 255 CPUs and also
would be reused by ARM target when ACPI CPU hotplug
is introduced there.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it adds CPU objects to DSDT with _STA method
and QEMU side of CPU hotplug interface initialization
with registers sufficient to handle _STA requests,
including necessary hotplug callbacks in piix4,ich9 code.
Hot-(un)plug hw/acpi parts will be added by
corresponding follow up patches.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used to select which hotplug call-back is called
and for switching from legacy mode into new one.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current code creates a whole page mmio region for the MSI-X table
size.
However, the page containing the MSI-X table may contain other registers
not related to MSI-X. Creating an mmio region for the whole page masks
such registers and may break drivers in the guest OS.
Since maximal number of entries is known, use that instead to deduce the
table size when setting up the mmio region.
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 6 is used to set Namespace Label Data
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 5 is used to get Namespace Label Data
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Function 4 is used to get Namespace label size
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently only revision 1 is supported
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It separates the operations between root device and nvdimm devices
in order to introducing label functions support for nvdimm device
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check arg0 which indicates UUID to see if it is valid
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Check if the input Arg3 is valid then store it into ARG3 if it is
needed
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now we pass HDLE to Qemu properly, use 0 for root device and use the
handle for nvdimm devices
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be used by NVDIMM ACPI
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement ObjectType which is used by NVDIMM _DSM method in
later patch
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a parameter, 'label-size', which is the size of nvdimm label
data area which is reserved at the end of backend memory. It is required
at least 128k
Two callbacks, read_label_data() and write_label_data(), are used to
operate the label area
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This callback returns the MemoryRegion that is the memory of dimm should
be kept during live migration
nvdimm device is different with pc-dimm as its memory includes not only
the MemoryRegion directly mapping to guest's address space but also the
memory used as label data
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the ACPI table construction tools to create an ACPI entry
for IPMI. This adds a function called build_acpi_ipmi_devices
to add an DSDT entry for IPMI if IPMI is compiled in and an
IPMI device exists. It also adds a dummy function if IPMI
is not compiled in.
This conforms to section "C3-2 Locating IPMI System Interfaces in
ACPI Name Space" in the IPMI 2.0 specification.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add an IPMI table entry to the SMBIOS.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This will let things in other files (like IPMI) build SMBIOS tables.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently outstanding patches for spapr, target-ppc and related
devices. This batch has:
* Significant new progress towards full support for hypervisor
mode
* Assorted bugfixes
* Some preliminary patches towards dynamic DMA window support
The last involves a change to memory.c, which Paolo has said I can
take through this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Da1O
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160623' into staging
ppc patch queue for 2016-06-23
Currently outstanding patches for spapr, target-ppc and related
devices. This batch has:
* Significant new progress towards full support for hypervisor
mode
* Assorted bugfixes
* Some preliminary patches towards dynamic DMA window support
The last involves a change to memory.c, which Paolo has said I can
take through this tree.
# gpg: Signature made Thu 23 Jun 2016 06:47:53 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160623:
ppc: Disable huge page support if it is not available for main RAM
ppc: Add P7/P8 Power Management instructions
ppc: Move exception generation code out of line
ppc: Turn a bunch of booleans from int to bool
ppc: Add real mode CI load/store instructions for P7 and P8
ppc: Rework generation of priv and inval interrupts
ppc: Fix generation if ISI/DSI vs. HV mode
ppc: Fix POWER7 and POWER8 exception definitions
ppc: fix exception model for HV mode
ppc: define a default LPCR value
ppc: Fix rfi/rfid/hrfi/... emulation
memory: Add reporting of supported page sizes
ppc: Improve emulation of THRM registers
target-ppc: Fix rlwimi, rlwinm, rlwnm again
ppc64: disable gen_pause() for linux-user mode
tests: Use '+=' to add additional tests, not '='
powerpc/mm: Update the WIMG check during H_ENTER
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make attached property settable and turns off auto-attach in case the
device was hotplugged. Hotplugging works simliar to usb-bot now.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-6-git-send-email-kraxel@redhat.com
This patch marks usb-bot as hot-pluggable device, makes attached
property settable and turns off auto-attach in case the device
was hotplugged.
Hot-plugging a usb-bot device with one or more scsi devices can be
done this way now:
(1) device-add usb-bot,id=foo
(2) device-add scsi-{hd,cd},bus=foo.0,lun=0
(2b) optionally add more devices (luns 0 ... 15).
(3) qom-set foo.attached = true
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-5-git-send-email-kraxel@redhat.com
USB devices in attached state are visible to the guest. This patch adds
a QOM property for this. Write access is opt-in per device. Some
devices manage attached state automatically (usb-host, usb-serial,
usb-redir), so we can't enable write access universally but have to do
it on a case by case base. So far, no device opts in.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1465984019-28963-4-git-send-email-kraxel@redhat.com
[ minor codestyle fix ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 9432e53a5b added xen_sysdev as a
system device to serve as an anchor for removable virtual buses. This
introduced a build failure for non-x86 builds with CONFIG_XEN_BACKEND
set, as xen_sysdev was defined in a x86 specific file while being
consumed in an architecture independent source.
Move the xen_sysdev definition and initialization to xen_backend.c to
avoid the build failure.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
In case the word size of the domU and qemu running the qdisk backend
differ BLKIF_OP_DISCARD will not work reliably, as the request
structure in the ring have different layouts for different word size.
Correct this by copying the request structure in case of different
word size element by element in the BLKIF_OP_DISCARD case, too.
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Every IOMMU has some granularity which MemoryRegionIOMMUOps::translate
uses when translating, however this information is not available outside
the translate context for various checks.
This adds a get_min_page_size callback to MemoryRegionIOMMUOps and
a wrapper for it so IOMMU users (such as VFIO) can know the minimum
actual page size supported by an IOMMU.
As IOMMU MR represents a guest IOMMU, this uses TARGET_PAGE_SIZE
as fallback.
This removes vfio_container_granularity() and uses new helper in
memory_region_iommu_replay() when replaying IOMMU mappings on added
IOMMU memory region.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: Removed an unnecessary calculation]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Support for 0 value for memeory coherence is optional and with ppc64
we can always enable memory coherence. Linux kernel did that during
the development of 4.7 kernel. But that resulted in failure in Qemu
in H_ENTER hcall due to below check. The mentioned change was reverted
in the kernel and kernel right now enable memory coherence only if
cache inhibited is not set. Nevertheless update qemu WIMG flag check
to cover the case where we enable memory coherence along with cache
inhibited flag.
In order to handle older and newer kernel version consider both Cache
inhibitted and (cache inhibitted | memory conference) as valid values
for wimg flags.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/alpha/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-33-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/arm/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-32-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/acpi/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-31-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/vfio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-30-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/s390x/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1466066426-16657-29-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/pci/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-28-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/ppc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1466066426-16657-27-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/9pfs/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-26-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/i386/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-25-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/isa/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-24-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/sd/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-23-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/sparc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-22-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/dma/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-21-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/timer/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-20-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/input/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-19-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/display/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-18-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/nvram/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-17-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/scsi/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-16-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/usb/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-15-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/misc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-14-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/audio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-13-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/virtio/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-12-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/net/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-11-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/intc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-10-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/char/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-9-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Move all trace-events for files in the hw/block/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-8-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The old milkymist.org domain just forwards to mm-labs.hk nowadays. I've
created a mirror of the documents.
Signed-off-by: Michael Walle <michael@walle.cc>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* Drop the old SysBus init function and use instance_init
* Move graphic_console_init into realize stage
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* Drop the old SysBus init function and use instance_init
* Move tmu2_glx_init into realize stage
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This patch simplifies code that uses a local_err variable just to
immediately use it for an error_propagate() call.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/remove_local_err.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-3-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Blank line in s390-virtio-ccw.c restored]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
error_propagate() already ignores local_err==NULL, so there's no
need to check it before calling.
Coccinelle patch used to perform the changes added to
scripts/coccinelle/error_propagate_null.cocci.
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-2-git-send-email-ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix missing includes of qemu/log.h, which broke compilation with the
simple trace backend (the default backend pulls in log.h implicitly
via trace.h).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Tested-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Message-id: 1466416634-9798-1-git-send-email-peter.maydell@linaro.org
In ACPI 5.1 Errata, it adds GIC version in GIC distributor structure.
This is useful for guest kernel to identify which version GIC hardware
is. Update GIC distributor structure and present GIC version in MADT
table.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465960955-17388-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Value matching allows Linux to boot with CONFIG_NO_HZ_IDLE=y on the
palmetto-bmc machine. Two match registers are provided for each timer.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1465974248-20434-1-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the CPU interface registers which deal with acknowledging
and dismissing interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-19-git-send-email-peter.maydell@linaro.org
Implement the registers in the GICv3 CPU interface which generate
new SGI interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-18-git-send-email-peter.maydell@linaro.org
Implement the gicv3_cpuif_update() function which deals with correctly
asserting IRQ and FIQ based on the current running priority of the CPU,
the priority of the highest priority pending interrupt and the CPU's
current exception level and security state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-17-git-send-email-peter.maydell@linaro.org
Implement the CPU interface registers for the GICv3; these are
CPU system registers, not MMIO registers.
This commit implements all the registers which are simple
accessors for GIC state, but not those which act as interfaces
for acknowledging, dismissing or generating interrupts. (Those
will be added in a later commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-16-git-send-email-peter.maydell@linaro.org
Implement the code which updates the GIC state when an interrupt
input into the GIC is asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-15-git-send-email-peter.maydell@linaro.org
Wire up the MMIO functions exposed by the distributor and the
redistributor into MMIO regions exposed by the GICv3 device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-14-git-send-email-peter.maydell@linaro.org
Implement the redistributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-13-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the distributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-12-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new bitmap data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the GICv3 logic to recalculate the highest priority pending
interrupt for each CPU after some part of the GIC state has changed.
We avoid unnecessary full recalculation where possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-11-git-send-email-peter.maydell@linaro.org
This patch includes the device class itself, some ID register
value functions which will be needed by both distributor
and redistributor, and some skeleton functions for handling
interrupts coming in and going out, which will be filled in
in a subsequent patch.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-10-git-send-email-peter.maydell@linaro.org
[PMM: pulled this patch earlier in the sequence, and left
some code out of it for a later patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Add state structure descriptors for the GICv3 state. We mark
the KVM GICv3 device as having a migration blocker until the
code to save and restore the state in the kernel is implemented.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-9-git-send-email-peter.maydell@linaro.org
[PMM: Adjust to renamed struct fields; switched to using uint32_t
array backed bitmaps; add migration blocker setting]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the GICv3 parent_irq and parent_fiq pointers into the
GICv3CPUState structure rather than giving them their own array.
This will make it easy to assert the IRQ and FIQ lines for a
particular CPU interface without having to know or calculate
the CPU index for the GICv3CPUState we are working on.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-8-git-send-email-peter.maydell@linaro.org
Add state information to GICv3 object structure and implement
arm_gicv3_common_reset().
This commit includes accessor functions for the fields which are
stored as bitmaps in uint32_t arrays.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-7-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled:
* Add missing qom/cpu.h include
* Remove legacy-only state fields (we can add them later if/when we add
legacy emulation)
* Use arrays of uint32_t to store the various distributor bitmaps,
and provide accessor functions for the various set/test/etc operations
* Add various missing register offset #defines
* Accessor macros which combine distributor and redistributor behaviour
removed
* Fields in state structures renamed to match architectural register names
* Corrected the reset value for GICR_IENABLER0 since we don't support
legacy mode
* Added ARM_LINUX_BOOT_IF interface for "we are directly booting a kernel in
non-secure" so that we can fake up the firmware-mandated reconfiguration
only when we need it
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
If the same GlobalProperty struct is registered twice, the list
entry gets corrupted, making tqe_next points to itself, and
qdev_prop_set_globals() gets stuck in a loop. The bug can be
easily reproduced by running:
$ qemu-system-x86_64 -rtc-td-hack -rtc-td-hack
Change global_props to use GList instead of queue.h, making the
code simpler and able to deal with properties being registered
twice.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Here's the current accumulated set of spapr, ppc and related patches.
* The big thing in here is CPU hotplug for spapr
- This includes a number of acked generic changes adding new
infrastructure for hotplugging cpu cores
* A number of TCG bug fixes are also included
* This adds a new testcase to make it harder to accidentally break
Macintosh (and other openbios) platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AGZ4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.7-20160617' into staging
ppc patch queue for 2016-06-17
Here's the current accumulated set of spapr, ppc and related patches.
* The big thing in here is CPU hotplug for spapr
- This includes a number of acked generic changes adding new
infrastructure for hotplugging cpu cores
* A number of TCG bug fixes are also included
* This adds a new testcase to make it harder to accidentally break
Macintosh (and other openbios) platforms
# gpg: Signature made Fri 17 Jun 2016 07:35:29 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160617:
spapr: implement query-hotpluggable-cpus callback
hmp: Add 'info hotpluggable-cpus' HMP command
QMP: Add query-hotpluggable-cpus
spapr: CPU hot unplug support
spapr: CPU hotplug support
spapr: convert boot CPUs into CPU core devices
spapr: Move spapr_cpu_init() to spapr_cpu_core.c
spapr: Abstract CPU core device and type specific core devices
qom: API to get instance_size of a type
spapr_drc: Prevent detach racing against attach for CPU DR
xics,xics_kvm: Handle CPU unplug correctly
cpu: Abstract CPU core type
qdev: hotplug: Introduce HotplugHandler.pre_plug() callback
target-ppc: Fix rlwimi, rlwinm, rlwnm
vfio: Fix broken EEH
target-ppc: Bug in BookE wait instruction
ppc / sparc: Add a tester for checking whether OpenBIOS runs successfully
hw/ppc/spapr: Silence deprecation message in qtest mode
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Beginning of reconnect support for vhost-user.
Misc cleanups and fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXY0Q3AAoJECgfDbjSjVRpkVcH/2gTHRE9yUoWe6ROvPV67BKx
8Iy9GzJ3BMO3RolVZEA5KXIevn5TG+pV274BZEuXMD3AL/molv279p0o/gvBYoqq
V0jNH2MO+MV6D9OzhUXcgWSejvybF5W07ojPDU/hlgtFXPZFbJDyt95MWaLiilOg
cCtTuRqgrrRaypcnnk/CIDbC+Ek2kAYdgQHQbfj9ihle3TWO8R0bSXnFqSaqCIkM
4slMlv8y82fODeiO83nkpfAP1NCnfnRC8r8Gv7hbEUTlZQntavx5DuYdiIx6nsJE
W0g+Gpe1o0+jRuMnucGIUZvqzZ0e/I0wZuV16Nsfx+Rbd5+4CzTxZda5Qb05v7I=
=BHbJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
Beginning of reconnect support for vhost-user.
Misc cleanups and fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 17 Jun 2016 01:28:39 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
MAINTAINERS: add Marcel to PCI
msi_init: change return value to 0 on success
fix some coding style problems
pci core: assert ENOSPC when add capability
test: start vhost-user reconnect test
tests: append i386 tests
vhost-net: save & restore vring enable state
vhost-net: save & restore vhost-user acked features
vhost-net: do not crash if backend is not present
vhost-user: disconnect on start failure
qemu-char: add qemu_chr_disconnect to close a fd accepted by listen fd
tests/vhost-user-bridge: workaround stale vring base
tests/vhost-user-bridge: add client mode
vhost-user: add ability to know vhost-user backend disconnection
pci: fix pci_requester_id()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
tests/Makefile.include
It returns a list of present/possible to hotplug CPU
objects with a list of properties to use with
device_add.
in spapr case returned list would looks like:
-> { "execute": "query-hotpluggable-cpus" }
<- {"return": [
{ "props": { "core": 8 }, "type": "POWER8-spapr-cpu-core",
"vcpus-count": 2 },
{ "props": { "core": 0 }, "type": "POWER8-spapr-cpu-core",
"vcpus-count": 2,
"qom-path": "/machine/unattached/device[0]"}
]}'
TODO:
add 'node' property for core <-> numa node mapping
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Remove the CPU core device by removing the underlying CPU thread devices.
Hot removal of CPU for sPAPR guests is achieved by sending the hot unplug
notification to the guest. Release the vCPU object after CPU hot unplug so
that vCPU fd can be parked and reused.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Set up device tree entries for the hotplugged CPU core and use the
exising RTAS event logging infrastructure to send CPU hotplug notification
to the guest.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce sPAPRMachineClass.dr_cpu_enabled to indicate support for
CPU core hotplug. Initialize boot time CPUs as core deivces and prevent
topologies that result in partially filled cores. Both of these are done
only if CPU core hotplug is supported.
Note: An unrelated change in the call to xics_system_init() is done
in this patch as it makes sense to use the local variable smt introduced
in this patch instead of kvmppc_smt_threads() call here.
TODO: We derive sPAPR core type by looking at -cpu <model>. However
we don't take care of "compat=" feature yet for boot time as well
as hotplug CPUs.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Start consolidating CPU init related routines in spapr_cpu_core.c. As
part of this, move spapr_cpu_init() and its dependencies from spapr.c
to spapr_cpu_core.c
No functionality change in this patch.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
[dwg: Rename TIMEBASE_FREQ to SPAPR_TIMEBASE_FREQ, since it's now in a
public(ish) header]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add sPAPR specific abastract CPU core device that is based on generic
CPU core device. Use this as base type to create sPAPR CPU specific core
devices.
TODO:
- Add core types for other remaining CPU types
- Handle CPU model alias correctly
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If a CPU is hot removed while hotplug of the same is still in progress,
the guest crashes. Prevent this by ensuring that detach is done only
after attach has completed.
The existing code already prevents such race for PCI hotplug. However
given that CPU is a logical DR unlike PCI and starts with ISOLATED
state, we need a logic that works for CPU too.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[Don't set awaiting_attach for PCI devices]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
XICS is setup for each CPU during initialization. Provide a routine
to undo the same when CPU is unplugged. While here, move ss->cs management
into xics from xics_kvm since there is nothing KVM specific in it.
Also ensure xics reset doesn't set irq for CPUs that are already unplugged.
This allows reboot of a VM that has undergone CPU hotplug and unplug
to work correctly.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add an abstract CPU core type that could be used by machines that want
to define and hotplug CPUs in core granularity.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
[Integer core property]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
[dwg: changed property names to 'core-id' and 'nr-threads']
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
pre_plug callback is to be called before device.realize() is executed.
This would allow to check/set device's properties from HotplugHandler.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
vfio_eeh_container_op() is the backend that communicates with
host kernel to support EEH functionality in QEMU. However, the
functon should return the value from host kernel instead of 0
unconditionally.
dwg: Specifically the problem occurs for the handful of EEH
sub-operations which can return a non-zero, non-error result.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
[dwg: clarification to commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
No caller use its return value as msi capability offset, also in order
to make its return behaviour consistent with msix_init().
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Paolo Bonzini <pbonzini@redhat.com>
cc: Hannes Reinecke <hare@suse.de>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It has:
1. More newlines make the code block well separated.
2. Add more comments for msi_init.
3. Fix a indentation in vmxnet3.c.
4. ioh3420 & xio3130_downstream: put PCI Express capability init function
together, make it more readable.
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
cc: Dmitry Fleytman <dmitry@daynix.com>
cc: Jason Wang <jasowang@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ENOSPC is programming error, assert it for debugging.
cc: Michael S. Tsirkin <mst@redhat.com>
cc: Marcel Apfelbaum <marcel@redhat.com>
cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A driver may change the vring enable state at run time but vhost-user
backend may not be present (a contrived example is when the backend is
disconnected and the device is reconfigured after driver rebinding)
Restore the vring state when the vhost-user backend is started, so it
can process the ring.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The initial vhost-user connection sets the features to be negotiated
with the driver. Renegotiation isn't possible without device reset.
To handle reconnection of vhost-user backend, ensure the same set of
features are provided, and reuse already acked features.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Do not crash when backend is not present while enabling the ring. A
following patch will save the enabled state so it can be restored once
the backend is started.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Reviewed-by: Victor Kaplansky <victork@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This fix SID verification failure when IOMMU IR is enabled with PCI
bridges. Existing pci_requester_id() is more like getting BDF info
only. Renaming it to pci_get_bdf(). Meanwhile, we provide the correct
implementation to get requester ID. VT-d spec 5.1.1 is a good reference
to go, though it talks only about interrupt delivery, the rule works
exactly the same for non-interrupt cases.
Currently, there are three use cases for pci_requester_id():
- PCIX status bits: here we need BDF only, not requester ID. Replacing
with pci_get_bdf().
- PCIe Error injection and MSI delivery: for both these cases, we are
looking for requester IDs. Here we should use the new impl.
To avoid a PCI walk every time we send MSI message, one requester_id
cache field is added to PCIDevice to cache the result when initialize
PCI device.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When running "make check", there is currently always an error message
saying "spapr-pci-vfio-host-bridge is deprecated". This happens because
the QOM tests are instantiating all possible devices, and the error
message is currently located in the instance_init() function of the
device. Since it is legal for the tests to instantiate a device without
using it, the error message should be silenced when we're running in
test mode.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While doing DMA read into ESP command buffer 's->cmdbuf', it could
write past the 's->cmdbuf' area, if it was transferring more than 16
bytes. Increase the command buffer size to 32, which is maximum when
's->do_cmd' is set, and add a check on 'len' to avoid OOB access.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid duplicated code between esp_do_dma and handle_ti. esp_do_dma
has the same code that handle_ti contains after the call to esp_do_dma;
but the code in handle_ti is never reached because it is in an "else if".
Remove the else and also the pointless return.
esp_do_dma also has a partially dead assignment of the to_device
variable. Sink it to the point where it's actually used.
Finally, assert that the other caller of esp_do_dma (esp_transfer_data)
only transfers data and not a command. This is true because get_cmd
cancels the old request synchronously before its caller handle_satn_stop
sets do_cmd to 1.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer.
Routine get_cmd() in non-DMA mode, uses 'ti_size' to read scsi
command into a buffer. Add check to validate command length against
buffer size to avoid any overrun.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1464717207-7549-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some source code analyzers like cppcheck spill out a warning if
the sign of the argument does not match the format string.
Ticket: https://bugs.launchpad.net/qemu/+bug/1589564
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1465805418-15906-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu/osdep.h checks whether MAP_ANONYMOUS is defined, but this check
is bogus without a previous inclusion of sys/mman.h. Include it in
sysemu/os-posix.h and remove it from everywhere else.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
commit 243e6f69c1 ("m25p80: Switch to byte-based block access")
replaced blk_read() calls with blk_pread() but return values are
different.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds the DP and the DPDMA to the Zynq MP platform.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-10-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the implementation of the DisplayPort.
It has an aux-bus to access dpcd and edid.
Graphic plane is connected to the channel 3.
Video plane is connected to the channel 0.
Audio stream are connected to the channels 4 and 5.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1465833014-21982-9-git-send-email-fred.konrad@greensocs.com
[PMM: fixed format strings]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the implementation of the DPDMA.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-8-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement an I2C slave which implements DDC and returns the
EDID data for an attached monitor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1465833014-21982-7-git-send-email-fred.konrad@greensocs.com
- Rebased on the current master.
- Modified for QOM.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
[PMM: actually wire up the vmstate to dc->vmsd]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces dpcd module.
It wires on a aux-bus and can be accessed by the driver to get lane-speed, etc.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-6-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces a new bus: aux-bus.
It contains an address space for aux slaves devices and a bridge to an I2C bus
for I2C through AUX transactions.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1465833014-21982-5-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most of the control flow logic between send and recv (error checking
etc) is the same. Factor this out into a common send_recv() API.
This is then usable by clients, where the control logic for send
and receive differs only by a boolean. E.g.
if (send)
i2c_send(...):
else
i2c_recv(...);
becomes:
i2c_send_recv(... , send);
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1465833014-21982-4-git-send-email-fred.konrad@greensocs.com
Changes from FK:
* Rebased on master.
* Rebased on my i2c broadcast patch.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This does a write to every slaves when the I2C bus get a write to address 0.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-3-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The dev field in i2cbus is not used.
So just drop it.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-2-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
split the old SysBus init function into an instance_init
and a Device realize function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-13-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
split the old SysBus init function into an instance_init
and a Device realize function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-12-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-11-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-10-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-9-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-8-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Merge the pl061_initfn into pl061_init
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-7-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the old SysBus init into an instance_init and
DeviceClass::realize function
* Drop the SysBus init function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-6-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-5-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the omap_i2c_init into an instance_init and realize function
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-4-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Rename the exynos4210_i2c_realize to exynos4210_i2c_init
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-3-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465815255-21776-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465746713-30414-5-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two variants of DEFINE_VIRT_MACHINE. One, just called
DEFINE_VIRT_MACHINE, that does not set properties that only
the latest machine type should have, and another that does.
This will hopefully reduce potential for errors when adding
new versions.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465746713-30414-4-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DEFINE_VIRT_MACHINE to generate versioned machine type info.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465746713-30414-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename machvirt_info (which is specifically for 2.6 TypeInfo)
to machvirt_2_6_info, and separate the type registration of the
abstract machine type from the versioned type.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465746713-30414-2-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add PMU IRQ number in ACPI table, then we can use PMU in guest through
ACPI.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465267577-1808-4-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a virtual PMU device for virt machine while use PPI 7 for PMU
overflow interrupt number.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465267577-1808-3-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
If qdev_try_create() is passed NULL for the bus, it will automatically
put the newly created device onto the default system bus. However
if the device is not actually a SysBusDevice then this will result
in later crashes (for instance when running the monitor "info qtree"
command) because code reasonably assumes that all devices on the system
bus are system bus devices.
Generally the mistake is that the calling code should create the
object with object_new(TYPE_FOO) rather than qdev_create(NULL, TYPE_FOO);
see commit 6749695eaa for an example of fixing this bug.
Assert in qdev_try_create() if the device isn't suitable to put on
the system bus, so that this mistake results in failure earlier
and more reliably.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The sclp scp read info call fills in a buffer with information about the
system. With more than 248 CPUs we overflow the 4k buffer of the SCCB,
leading to random data corruption. Basically ALL guest operating systems
call scp read info, so let's limit the machines to 248 CPUs to make it
obvious that >=249 does not work.
As KVM also limits itself to 248 and TCG on s390 does not support
SMP, this should cause no regression for any user as no VMs with more
than 248 VCPUs were ever possible.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
This allows to trace changes in the summary and queue indicators
for the non-irqfd case. For irqfd, kernel traces are needed instead.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Let's introduce a CssDevId to handle device ids of the xx.x.xxxx
type used for channel devices. This has some benefits:
- We can use them in virtio-ccw and split the validity checks for
a channel device id in general from the constraint checking
within the virtio-ccw scope.
- We can reuse the device id type for future non-virtio channel
devices.
While we're at it, improve the validity checks and disallow e.g.
trailing characters.
Suggested-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Acked-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
According to the Principles of Operation (more precisely the subsection
'Channel-Report Word'), a subchannel put into the installed parameters
initialized state is in the same state as after an I/O system reset (just
parameters possibly changed). This implies that any I/O interrupts for that
subchannel are no longer pending (as I/O system resets clear I/O
interrupts). Therefore, we need an interface to clear pending I/O
interrupts. Make css_generate_sch_crws clear the pending IO interrupts for
the subchannel.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
According to the platform specification, under certain conditions,
pending IO interruptions have to be cleared. Let's add an interface
for that.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Memory hotplug can fail for some combinations of RAM and maxmem when
DDW is enabled in the presence of devices like nec-usb-xhci. DDW depends
on maximum addressable memory returned by guest and this value is currently
being calculated wrongly by the guest kernel routine memory_hotplug_max().
While there is an attempt to fix the guest kernel, this patch works
around the problem within QEMU itself.
memory_hotplug_max() routine in the guest kernel arrives at max
addressable memory by multiplying lmb-size with the lmb-count obtained
from ibm,dynamic-memory property. There are two assumptions here:
- All LMBs are part of ibm,dynamic memory: This is not true for PowerKVM
where only hot-pluggable LMBs are present in this property.
- The memory area comprising of RAM and hotplug region is contiguous: This
needn't be true always for PowerKVM as there can be gap between
boot time RAM and hotplug region.
To work around this guest kernel bug, ensure that ibm,dynamic-memory
has information about all the LMBs (RMA, boot-time LMBs, future
hotpluggable LMBs, and dummy LMBs to cover the gap between RAM and
hotpluggable region).
RMA is represented separately by memory@0 node. Hence mark RMA LMBs
and also the LMBs for the gap b/n RAM and hotpluggable region as
reserved and as having no valid DRC so that these LMBs are not considered
by the guest.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This ensures that the underlying memory is marked dirty once the transfer
is complete and resolves cache coherency problems under MacOS 9.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Make sure that guests can use the PowerISA 2.07 CPU sPAPR
compatibility mode when they request it and the target CPU
supports it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The current pcr_mask values are ambiguous: Should these be the mask
that defines valid bits in the PCR register? Or should these rather
indicate which compatibility levels are possible? Anyway, POWER6 and
POWER7 should certainly not use the same values here. So let's
introduce an additional variable "pcr_supported" here which is
used to indicate the valid compatibility levels, and use pcr_mask
to signal the valid bits in the PCR register.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The h_client_architecture_support() function has become quite big
and nested already. So factor out the code that takes care of the
sPAPR compatibility PVRs (which will be modified by the following
patches).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit f9e98e5d7a ("xen/blkif: Avoid double access to
src->nr_segments") didn't go far enough: src->operation is also being
used twice. And nothing was done to prevent the compiler from using the
source side of the copy done by blk_get_request() (granted that's very
unlikely).
Move the barrier()s up, and add another one to blk_get_request().
Note that for completing XSA-155, the barrier() getting added to
blk_get_request() would suffice, and hence the changes to xen_blkif.h
are more like just cleanup. And since, as said, the unpatched code
getting compiled to something vulnerable is very unlikely (and not
observed in practice), this isn't being viewed as a new security issue.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
This wrapper for machine_usb(current_machine) is not necessary,
replace all usages of usb_enabled() with machine_usb().
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: qemu-arm@nongnu.org
Cc: qemu-ppc@nongnu.org
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 1465419025-21519-3-git-send-email-ehabkost@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Simplify initialization logic by removing the usb_enabled()
check. The USB controller is part of the SoC, so it doesn't make
sense to create a system where it is not present.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: qemu-arm@nongnu.org,
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465419025-21519-2-git-send-email-ehabkost@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Use stl_le_p() and ldl_le_p() to read and write data from
buffers, rather than using pointer casts and cpu_to_le32()
for writes and le32_to_cpup() for reads. This:
* avoids lots of casts
* works even if the buffer isn't as aligned as the host would like
* avoids using the *_to_cpup() functions which we want to get rid of
Note that there may still be some places where a pointer from the
guest is cast to a pointer to a host structure; these would also
have to be changed for the device to work on a host CPU which
enforces alignment restrictions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1465573077-29221-1-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch changes usb-host behavior in case we hostbus= and hostaddr=
properties are used to identify the usb device in question. Instead of
adding the device to the hotplug watchlist we try to open directly using
the given bus number and device address.
Putting a device specified by hostaddr to the hotplug watchlist isn't
a great idea as the address isn't a fixed property. It changes every
time the device is plugged in. So considering this case as "use the
device at bus:addr _now_" is more sane. Also usb-host will throw errors
in case it can't initialize the host device.
Note: For devices on the hotplug watchlist (hostport or vendorid or
productid specified) qemu continues to ignore errors and keeps
monitoring the usb bus to see if the device eventually shows up.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464945175-28939-1-git-send-email-kraxel@redhat.com
The function cpu_resume_from_signal() is now always called with a
NULL puc argument, and is rather misnamed since it is never called
from a signal handler. It is essentially forcing an exit to the
top level cpu loop but without raising any exception, so rename
it to cpu_loop_exit_noexc() and drop the useless unused argument.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Riku Voipio <riku.voipio@linaro.org>
Message-id: 1463494687-25947-4-git-send-email-peter.maydell@linaro.org
commit f0d1d2c115
("hw/char: QOM'ify pl011 model") break qemu-system-arm virt machine
if option '-machine secure=on' is provided.
The function create_uart is called twice. So make CharDriverState pointer
a parameter to create_uart instead of hardcoded.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Tested-by: Jerome Forissier <jerome.forissier@linaro.org>
Message-id: 1465353045-26323-1-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace (((n) + (d) - 1) /(d)) by DIV_ROUND_UP(n,d).
This patch is the result of coccinelle script
scripts/coccinelle/round.cocci
CC: qemu-block@nongnu.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Remove glib.h includes, as it is provided by osdep.h.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since mit_delay can never be 0 this if statement is
superfluous.
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Replace tab with 4 spaces; brace the indented statement.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
include:
1. remove unnecessary declaration of static function
2. fix inconsistency between comment and function name, and typo OOM->QOM
2. update comments of functions, use uniform format(GTK-Doc style)
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The coccinelle script:
scripts/coccinelle/overflow_muldiv64.cocci
gives us a list of potential overflows in muldiv64()
(the two first parameters are 64bit values).
This patch fixes one, as the fix seems obvious:
replace muldiv64(a, b, c) by muldiv64(b, a, c)
as "a" and "b" are 64bit values but a <= NANOSECONDS_PER_SECOND.
(10^9 -> 30bit value).
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When "a" and "b" are 32bit values, we don't have to cast
them to 128bit, 64bit is enough.
This patch is the result of coccinelle script
scripts/coccinelle/simplify_muldiv64.cocci
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
For xtensa PIC:
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
muldiv64(a, 1, b) is like "a / b".
This patch is the result of coccinelle script
scripts/coccinelle/remove_muldiv64.cocci.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
muldiv64() is "uint64_t muldiv64(uint64_t a, uint32_t b, uint32_t c)"
Some time it is used as muldiv64(uint32_t a, uint64_t b, uint32_t c)"
This patch is the result of coccinelle script
scripts/coccinelle/swap_muldiv64.cocci to reorder arguments.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Version: GnuPG v1
iQEcBAABAgAGBQJXVtmBAAoJEJykq7OBq3PI+eIH/3sx898eSWy9GcNddxvt9PwZ
XB4R0gVG3dcGupaRFvMV3C6kLbx+5YykdZTU5heN7R3k3pBNVdPlbYhAy4KnNQqJ
SPNTk2Y2yH4VtmjIJpl2bJsYbnxQN26gFaMWrs8UzFRVeDQjT0K0OyO5yHlVkDtE
gOMA6zTQ94L0wj3g3pz8PPOGzJ/mA3MvMq+Af0h7d4iiwUqSGfZVxOQ7eS92vdmb
VkSFOJSbckOb1k2IC9uwYpvaJR3KFp7RBY2joPYoD/kHv41oLRZ06ceHEuYWYGRK
9aLiXsWIfXijKTynbbB0HeLcUKvHZok39zWl9d0zNtZ3q7Akuz94aWvbqHABG+Y=
=1Q5r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging
# gpg: Signature made Tue 07 Jun 2016 15:26:09 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
throttle: refuse iops-size without iops-total/read/write
block: Drop bdrv_ioctl_bh_cb
block: Move BlockRequest type to io.c
block/io: optimize bdrv_co_pwritev for small requests
iostatus: fix comments for block_job_iostatus_reset
block/io: Remove unused bdrv_aio_write_zeroes()
virtio: drop duplicate virtio_queue_get_id() function
virtio-scsi: Remove op blocker for dataplane
virtio-blk: Remove op blocker for dataplane
blockdev-backup: Don't move target AioContext if it's attached
blockdev-backup: Use bdrv_lookup_bs on target
tests: avoid coroutine pool test crash
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This includes some infrastructure for ipmi smbios tables.
Beginning of acpi hotplug rework by Igor for supporting >255 CPUs.
Misc cleanups and fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXVsQ6AAoJECgfDbjSjVRp/7MH/i39kIjyUY0jrt/UDrNgXLoi
bi92ZdyyaeULg3rBFHlnweMs2VHChUATTc0DmXpr2hJbXm5MlZHQWHsv3UVpZ93h
ZVY99b5AF/2Im1MIfDmxImFU9YfHYQuAqW7ZNx+RtXpzuAvdd89K29y80iwlJ251
B1zhl9Tp8eePE3fZhbRElaTY70ruWonl+HOV9am7tfMDCTugYDPfLqdYT8fnaY98
GMbSkmRnOaRYeo23dsg2pX7DK+H3I4DO8qvis6Va4pRiwCCf9L0N2GAIrljpMdbk
yOCvvW3ujvCwkwwTwL1fPZTk1PTF3xhbgFZVvX2zOAWljhYkcesg4L8oERVBjwQ=
=sqxd
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
This includes some infrastructure for ipmi smbios tables.
Beginning of acpi hotplug rework by Igor for supporting >255 CPUs.
Misc cleanups and fixes.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 07 Jun 2016 13:55:22 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream: (25 commits)
virtio: move bi-endian target support to a single location
pc-dimm: introduce realize callback
pc-dimm: get memory region from ->get_memory_region()
acpi: make bios_linker_loader_add_checksum() API offset based
acpi: make bios_linker_loader_add_pointer() API offset based
tpm: apci: cleanup TCPA table initialization
acpi: cleanup bios_linker_loader_cleanup()
acpi: simplify bios_linker API by removing redundant 'table' argument
acpi: convert linker from GArray to BIOSLinker structure
pc: use AcpiDeviceIfClass.send_event to issue GPE events
acpi: extend ACPI interface to provide send_event hook
pc: Postpone SMBIOS table installation to post machine init
ipmi: rework the fwinfo to be fetched from the interface
tests: acpi: update tables with consolidated legacy cpu-hotplug AML
pc: acpi: cpuhp-legacy: switch ProcessorID to possible_cpus idx
pc: acpi: simplify build_legacy_cpu_hotplug_aml() signature
pc: acpi: consolidate legacy CPU hotplug in one file
pc: acpi: mark current CPU hotplug functions as legacy
pc: acpi: cpu-hotplug: make AML CPU_foo defines local to cpu_hotplug_acpi_table.c
pc: acpi: consolidate \GPE._E02 with the rest of CPU hotplug AML
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virtio_queue_get_id() function is the lesser used duplicate of
virtio_get_queue_index(). Use the latter instead.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1463767461-17922-1-git-send-email-stefanha@redhat.com
The previous patch dropped all op blockers from virtio-blk data plane.
The situation of virtio-scsi is exactly the same it can drop them too.
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1463969978-24970-5-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Block layer is prepared to unspecialize dataplane, an evidence is this
almost complete list of unblocked operations. It has all types except
two (actually three if DATAPLANE itself counts but blockdev.c makes sure
attaching twice is not possible): MIRROR_TARGET and BACKUP_TARGET.
blockdev-mirror refuses to start if target is attached, so the first is
not a problem.
By removing BACKUP_TARGET, blockdev-backup will become permissive to
write to a virtio-blk dataplane disk, but that is not worse than
non-dataplane given the latter is already possible. In either case,
blockdev.c always checks the target and source are on the same
AioContext, or bring them together if possible.
Signed-off-by: Fam Zheng <famz@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1463969978-24970-4-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Paolo's recent cpu.h cleanups broke legacy virtio for ppc64 LE guests (and
arm BE guests as well, even if I have not verified that). Especially, commit
"33c11879fd42 qemu-common: push cpu.h inclusion out of qemu-common.h" has
the side-effect of silently hiding the TARGET_IS_BIENDIAN macro from the
virtio memory accessors, and thus fully disabling support of endian changing
targets.
To be sure this cannot happen again, let's gather all the bi-endian bits
where they belong in include/hw/virtio/virtio-access.h.
The changes in hw/virtio/vhost.c are safe because vhost_needs_vring_endian()
is not called on a hot path and non bi-endian targets will return false
anyway.
While here, also rename TARGET_IS_BIENDIAN to be more precise: it is only for
legacy virtio and bi-endian guests.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
nvdimm needs to check if the backend memory is large enough to contain
label data and init its memory region when the device is realized, so
introduce realize callback which is called after common dimm has been
realize
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Curretly, the memory region of backed memory is all directly
mapped to guest's address space, however, it will be not true
for nvdimm device if we introduce nvdimm label which only can
be indirectly accessed by ACPI DSM method
Also it improves the comments a bit to reflect this fact
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
It should help to make clear that bios_linker works in terms
of offsets within a file. Also it should prevent mistakes
where user passes as arguments pointers to unrelated to file blobs.
While at it, considering that it's a ACPI checksum and
it's initial value must be 0, move checksum field zeroing
into bios_linker_loader_add_checksum() instead of doing it
at every call site manually before bios_linker_loader_add_checksum()
is called.
In addition add extra boundary checks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cleanup bios_linker_loader_add_pointer() API by switching
arguments to taking offsets relative to corresponding files
instead of doing pointer arithmetic on behalf of user which
were confusing.
Also make offset inside of source file explicit in API
so that user won't have to manually set it in
destination file blob and while at it add additional
boundary checks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At the time build_tpm_tcpa() is called the tcpalog size is
always 0, so log_area_start_address which is actually offset
from the start of ACPI_BUILD_TPMLOG_FILE is always 0.
Also as 'TCPA' is allocated 0 filled, there is no point
in calculating always 0 log_area_start_address and set
tcpa->log_area_start_address to it since the field should
always point to start of ACPI_BUILD_TPMLOG_FILE.
Make code easier to read dropping not needed offset
calculations.
While at that move tcpalog allocation closer to the code
that defines its size.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
bios_linker_loader_cleanup() is called only from one place
and returned value is immediately freed wich makes returning
pointer from bios_linker_loader_cleanup() useless.
Cleanup bios_linker_loader_cleanup() by freeing
data there so that caller won't have to free it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'table' argument in bios_linker_add_foo() commands is
a data blob of one of files also passed to the same API.
So instead of passing blob in every API call, add and keep
file name association with related blob at bios_linker_loader_alloc()
time.
And find blob by name looking up allocated file entries
inside of bios_linker_add_foo() commands.
It will:
- make API less confusing,
- enforce calling bios_linker_loader_alloc() before
calling any bios_linker_add_foo()
- make sure that blob is the correct one, i.e.
associated with the right file name
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Patch just changes type of of linker variables to
a structure, there aren't any functional changes.
Converting linker to a structure will allow to extend
it functionality in follow up patch adding sanity blob
checks.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it reduces number of args passed in handlers by 1 and
a number of used proxy wrappers saving ~20LOC.
Also it allows to make cpu/mem hotplug code more
universal as it would allow ARM to reuse it without
rewrite by providing its own send_event callback
to trigger events usiong GPIO instead of GPE
as fixed hadrware ACPI model doen't have GPE at all.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
send_event() hook will allow to send ACPI event in
a target specific way (GPE or GPIO based impl.)
it will also simplify proxy wrappers in piix4pm/ich9
that access ACPI regs and SCI which are part of
piix4pm/lcp_ich9 devices and call acpi_foo() API directly.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
This is the same place that the ACPI SSDT table gets added, so that
devices can add themselves to the SMBIOS table.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of scanning IPMI devices from a fwinfo list, allow
the fwinfo to be fetched from the IPMI interface class.
Then the code looking for IPMI fwinfo can scan devices on a
bus and look for ones that implement the IPMI class.
This will let the ACPI scope be defined by the calling
code so the IPMI code doesn't have to know the scope.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In legacy cpu-hotplug ProcessorID == APIC ID is used
in MADT and cpu-hotplug AML. It was fine as both
are 8bit and unique. Spec depricated Processor()
with corresponding ProcessorID and advises to use
Device() and UID instead of it.
However UID is just 32bit and it can't fit ARM's
arch_id(MPIDR) which is 64bit. Also in case of
sparse arch_id() distribution, managment/lookup
of maps by arch_id(APIC ID/MPIDR) becomes complex
and expensive.
In preparation to common CPU hotplug with ARM
and to simplify lookup in possible_cpus[] map
switch ProcessorID to possible_cpus index in
MADT.
Legacy cpu-hotplug considerations:
HW interface of it is APIC ID based bitmask so
it's impossible to change, also CPON package in
AML also APIC ID based as well all the methods.
To avoid massive rewrite of AML keep is so and
just break assumption that ProcessorID == APIC ID,
ammending CPU_MAT_METHOD to accept APIC ID and
possible_cpus index, it needs them both to patch
MADT entry template. Also switch to possible_cpus
index Processor(ProcessorID) AML.
That way changes to MADT/AML are minimal and kept
inside AML/MADT not affecting external interfaces.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
since IO block used by CPU hotplug is fixed size and
initialized it the same file as build_legacy_cpu_hotplug_aml()
just use ACPI_GPE_PROC_LEN directly instead of passing
it around in several files.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Since AML part of CPU hotplug is tightly coupled with
its hardware part (IO port layout/protocol), move
build_legacy_cpu_hotplug_aml() to cpu_hotplug.c
and remove empty cpu_hotplug_acpi_table.c
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
now as those defines are used only locally inside of
cpu_hotplug_acpi_table.c, move them out of header file.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
move the former SSDT part of CPU hoplug close to DSDT part.
AML is only moved but there isn't any functional change.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI spec requires GPE handlers only for GPE events
that hardware implements.
So remove AML for not supported by QEMU device model
events.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
While reading information via 'megasas_ctrl_get_info' routine,
a local bios version buffer isn't null terminated. Add the
terminating null byte to avoid any OOB access.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's become redundant since it was added in commit 09aa9a5 "spapr-pci:
enable adding PHB via -device".
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
KVM now supports 512 memslots on PowerPC (earlier it was 32). Allow half
of it (256) to be used as hotpluggable memory slots.
Instead of hard coding the max value, use the KVM supplied value if KVM
is enabled. Otherwise resort to the default value of 32.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be later used by the "ibm,reset-pe-dma-window" RTAS handler
which resets the DMA configuration to the defaults.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
LoPAPR dictates that during system reset all DMA windows must be removed
and the default DMA32 window must be created so does the patch.
At the moment there is just one window supported so no change in
behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We are going to have multiple DMA windows at different offsets on
a PCI bus. For the sake of migration, we will have as many TCE table
objects pre-created as many windows supported.
So we need a way to map windows dynamically onto a PCI bus
when migration of a table is completed but at this stage a TCE table
object does not have access to a PHB to ask it to map a DMA window
backed by just migrated TCE table.
This adds a "root" memory region (UINT64_MAX long) to the TCE object.
This new region is mapped on a PCI bus with enabled overlapping as
there will be one root MR per TCE table, each of them mapped at 0.
The actual IOMMU memory region is a subregion of the root region and
a TCE table enables/disables this subregion and maps it at
the specific offset inside the root MR which is 1:1 mapping of
a PCI address space.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The source guest could have reallocated the default TCE table and
migrate bigger/smaller table. This adds reallocation in post_load()
if the default table size is different on source and destination.
This adds @bus_offset, @page_shift to the migration stream as
a subsection so when DDW is added, migration to older machines will
still be possible. As @bus_offset and @page_shift are not used yet,
this makes no change in behavior.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently TCE tables are created once at start and their sizes never
change. We are going to change that by introducing a Dynamic DMA windows
support where DMA configuration may change during the guest execution.
This changes spapr_tce_new_table() to create an empty zero-size IOMMU
memory region (IOMMU MR). Only LIOBN is assigned by the time of creation.
It still will be called once at the owner object (VIO or PHB) creation.
This introduces an "enabled" state for TCE table objects, some
helper functions are added:
- spapr_tce_table_enable() receives TCE table parameters, stores in
sPAPRTCETable and allocates a guest view of the TCE table
(in the user space or KVM) and sets the correct size on the IOMMU MR;
- spapr_tce_table_disable() disposes the table and resets the IOMMU MR
size; it is made public as the following DDW code will be using it.
This changes the PHB reset handler to do the default DMA initialization
instead of spapr_phb_realize(). This does not make differenct now but
later with more than just one DMA window, we will have to remove them all
and create the default one on a system reset.
No visible change in behaviour is expected except the actual table
will be reallocated every reset. We might optimize this later.
The other way to implement this would be dynamically create/remove
the TCE table QOM objects but this would make migration impossible
as the migration code expects all QOM objects to exist at the receiver
so we have to have TCE table objects created when migration begins.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Suggested-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with internal 16-byte
FIFO buffers. One is used to handle commands and other is for
information transfer. Three control variables 'ti_rptr',
'ti_wptr' and 'ti_size' are used to control r/w access to the
information transfer buffer ti_buf[TI_BUFSZ=16]. In that,
'ti_rptr' is used as read index, where read occurs.
'ti_wptr' is a write index, where write would occur.
'ti_size' indicates total bytes to be read from the buffer.
While reading/writing to this buffer, index could exceed its
size. Add check to avoid OOB r/w access.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1465230883-22303-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The previous commit e7c9136977
(hw/char: QOM'ify escc.c) cause qemu-system-ppc/ppc64
OpenBIOS to freeze on startup, this commit fix it.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <1464767898-30526-1-git-send-email-zxq_yx_007@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch extends the functionality of the max-ram-below-4g option
to also allow increasing lowmem. Use case: Give as much memory as
possible to legacy non-PAE guests.
While being at it also rework the lowmem calculation logic and add a
longish comment describing how it works and what the compatibility
constrains are.
Note: This is a incompatible change. When setting max-ram-below-4g to
a value larger than 3.5G (or 3G with gigabyte alignment) it has no
effect on older qemu versions: qemu silently ignores it. With the patch
applied it actually has an effect and changes the ram layout. Highly
unlikely to hit in practive though as there is no reason start old qemu
versions that way.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1464857305-26675-1-git-send-email-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most Zynq UltraScale+ users will be targetting and using the ZCU102
board instead of the development focused EP108. To make our QEMU machine
names clearer add a ZCU102 machine model.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: cc82eec026b2febfca252d73362bb7084616c1ad.1464213234.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* create xilinx_uartlite_create wrapper function to create
xilinx_uartlite device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-6-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-5-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-4-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* create cadence_uart_create wrapper function to create
cadence_uart_device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-3-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* drop qemu_char_get_next_serial and use chardev prop
* add pl011_create wrapper function to create pl011 uart device
* change affected board code to use the new way
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1465028065-5855-2-git-send-email-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently ptimer users are used to store copy of the limit value, because
ptimer doesn't provide facility to retrieve the limit. Let's provide it.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 8f1fa9f90d8dbf8086fb02f3b4835eaeb4089cf6.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow switching between periodic <-> oneshot modes while timer is running.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: f030be6e28fbd219e1e8d22297aee367bd9af5bb.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Delta value must be updated on period/freq change, otherwise running timer
would be restarted (counter reloaded with old delta). Only m68k/mcf520x
and arm/arm_timer devices are currently doing freq change correctly, i.e.
stopping the timer. Perform delta update to fix affected devices and
eliminate potential further mistakes.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 4987ef5fdc128bb9a744fd794d3f609135c6a39c.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ptimer_get_count() might be called while QEMU timer already been expired.
In that case ptimer would return counter = 0, which might be undesirable
in case of polled timer. Do counter wrap around for periodic timer to keep
it distributed. In order to achieve more accurate emulation behaviour of
certain hardware, don't perform wrap around when in icount mode and return
counter = 0 in that case (that doesn't affect polled counter distribution).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 4ce381c7d24d85d165ff251d2875d16a4b6a5c04.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Multiple issues here related to the timer with a adjusted .limit value:
1) ptimer_get_count() returns incorrect counter value for the disabled
timer after loading the counter with a small value, because adjusted limit
value is used instead of the original.
For instance:
1) ptimer_stop(t)
2) ptimer_set_period(t, 1)
3) ptimer_set_limit(t, 0, 1)
4) ptimer_get_count(t) <-- would return 10000 instead of 0
2) ptimer_get_count() might return incorrect value for the timer running
with a adjusted limit value.
For instance:
1) ptimer_stop(t)
2) ptimer_set_period(t, 1)
3) ptimer_set_limit(t, 10, 1)
4) ptimer_run(t)
5) ptimer_get_count(t) <-- might return value > 10
3) Neither ptimer_set_period() nor ptimer_set_freq() are adjusting the
limit value, so it is still possible to make timer timeout value
arbitrary small.
For instance:
1) ptimer_set_period(t, 10000)
2) ptimer_set_limit(t, 1, 0)
3) ptimer_set_period(t, 1) <-- bypass limit correction
Fix all of the above issues by adjusting timer period instead of the limit.
Perform the adjustment for periodic timer only. Use the delta value instead
of the limit to make decision whether adjustment is required, as limit could
be altered while timer is running, resulting in incorrect value returned by
ptimer_get_count.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: cd141f74f5737480ec586b9c7d18cce1d69884e2.1464367869.git.digetx@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the in kernel GIC model when running with KVM enabled.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-5-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Delay the realization of the GIC until after CPUs are
realized. This is needed for KVM as the in-kernel GIC
model will fail if it is realized with no available CPUs.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-4-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The way we currently model the RPU subsystem is of quite
limited use. In addition to that, it causes problems for
KVM and for GDB debugging.
Make the RPU optional by adding a has_rpu property and
default to having it disabled.
This changes the default setup from having the RPU to not
longer having it.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a secure prop to en/disable ARM Security Extensions.
This is particularly useful for KVM runs.
Default to disabled to match the behavior of KVM.
This changes the default setup from having the ARM Security
Extensions to not longer having them.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
directly connected to the APB bus. They can be programmed as master or
slave but the propopsed model only supports the master mode.
On the TODO list, we also have :
- improve and harden the state machine.
- bus recovery support (used by the Linux driver).
- transfer mode state machine bits. this is not strictly necessary as
it is mostly used for debug. The bus busy bit is deducted from the
I2C core engine of qemu.
- support of the pool buffer: 2048 bytes of internal SRAM (not used
by the Linux driver).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1464704307-25178-1-git-send-email-clg@kaod.org
[PMM: removed unused functions aspeed_i2c_bus_get_state() and
aspeed_i2c_bus_set_state()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Treat non-secure accesses to registers and bits in registers of secure
interrupts as RAZ/WI.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Message-id: 1464273945-2055-1-git-send-email-jens.wiklander@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set the MMIO range limit field to 'base + size - 1' as required.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1463856217-17969-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAldVR/QACgkQAvw66wEB28JwVQCgiTy4bpShd9GiFgJ+eoSgJnt5
lLcAn3rnv44g0SpW5M7aK4I8RzyEig0X
=vbbR
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
readdir_r() to readdir() conversion, various minor cleanups
# gpg: Signature made Mon 06 Jun 2016 10:52:52 BST
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9p: switch back to readdir()
9p: add locking to V9fsDir
9p: introduce the V9fsDir type
9p: drop useless out: label
9p: drop useless inclusion of hw/i386/pc.h
9p/fsdev: remove obsolete references to virtio
9p: some more cleanup in #include directives
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit fcaafb1001 accidentally broke reads from
scsi-disk devices when being updated from its original form to use the new
byte-based block functions. Add the extra missing sector to offset conversion
in order to restore read functionality.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1464931021-25117-1-git-send-email-mark.cave-ayland@ilande.co.uk
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch changes the 9p code to use readdir() again instead of
readdir_r(), which is deprecated in glibc 2.24.
All the locking was put in place by a previous patch.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
If several threads concurrently call readdir() with the same directory
stream pointer, it is possible that they all get a pointer to the same
dirent structure, whose content is overwritten each time readdir() is
called.
We must thus serialize accesses to the dirent structure.
This may be achieved with a mutex like below:
lock_mutex();
readdir();
// work with the dirent
unlock_mutex();
This patch adds all the locking, to prepare the switch to readdir().
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
If we are to switch back to readdir(), we need a more complex type than
DIR * to be able to serialize concurrent accesses to the directory stream.
This patch introduces a placeholder type and fixes all users.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Most of the 9p code is now virtio agnostic. This patch does a final cleanup:
- drop references to Virtio from the header comments
- fix includes
Also drop a couple of leading empty lines while here.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
The "9p-attr.h" header isn't needed by 9p synth and virtio 9p.
While here, also drop last references to virtio from 9p synth since it is
now transport agnostic code.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
This patch fixes used-uninitialized false
positive while compiling with ust tracing
backend plus gcc 4.6.3:
hw/net/e1000e.c: In function ‘e1000e_io_write’:
hw/net/e1000e.c:170:39: error: ‘idx’ may be used uninitialized in this function [-Werror=uninitialized]
hw/net/e1000e.c: In function ‘e1000e_io_read’:
hw/net/e1000e.c:145:35: error: ‘idx’ may be used uninitialized in this function [-Werror=uninitialized]
cc1: all warnings being treated as errors
make: *** [hw/net/e1000e.o] Error 1
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-id: 1465023763-10773-1-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Store some additional state for cursor and resource backing storage,
so we can write out and reload things. Implement vmsave+vmload for
2d mode. Continue blocking live migration in 3d/virgl mode.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464009727-7753-1-git-send-email-kraxel@redhat.com
vmsvga_fifo_run is called in regular intervals (on each display update)
and will resume where it left off. So we can simply exit the loop,
without having to worry about how processing will continue.
Fixes: CVE-2016-4453
Cc: qemu-stable@nongnu.org
Cc: P J P <ppandit@redhat.com>
Reported-by: 李强 <liqiang6-s@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464592161-18348-5-git-send-email-kraxel@redhat.com
The fifo is normal ram. So kvm vcpu threads and qemu iothread can
access the fifo in parallel without syncronization. Which in turn
implies we can't use the fifo pointers in-place because the guest
can try changing them underneath us. So add shadows for them, to
make sure the guest can't modify them after we've applied sanity
checks.
Fixes: CVE-2016-4454
Cc: qemu-stable@nongnu.org
Cc: P J P <ppandit@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464592161-18348-4-git-send-email-kraxel@redhat.com
Sanity checks are applied when the fifo is enabled by the guest
(SVGA_REG_CONFIG_DONE write). Which doesn't help much if the guest
changes the fifo registers afterwards. Move the checks to
vmsvga_fifo_length so they are done each time qemu is about to read
from the fifo.
Fixes: CVE-2016-4454
Cc: qemu-stable@nongnu.org
Cc: P J P <ppandit@redhat.com>
Reported-by: 李强 <liqiang6-s@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1464592161-18348-2-git-send-email-kraxel@redhat.com
ust trace backend has limitation of maximum 10
arguments per event. Traces with more arguments
cannot be compiled for this backend.
Trace e1000e_rx_rss_ip6 introduced by previous
commits has 11 arguments and fails to compile with
ust trace backend.
This patch fixes the problem by splitting this
tracepoint into two successive tracepoints with
smaller number of arguments.
For more information see comment regarding TP_ARGS
in lttng/tracepoint.h:
/*
* TP_ARGS takes tuples of type, argument separated by a comma.
* It can take up to 10 tuples (which means that less than 10 tuples is
* fine too).
* Each tuple is also separated by a comma.
*/
Build log generated by this problem:
In file included from ./trace/generated-tracers.h:9:0,
from /home/travis/build/qemu/qemu/include/trace.h:4,
from util/oslib-posix.c:36:
./trace/generated-ust-provider.h:16556:3: error: unknown type name ‘_TP_EXPROTO_Bool’
In file included from /home/travis/build/qemu/qemu/include/trace.h:4:0,
from util/oslib-posix.c:36:
./trace/generated-tracers.h: In function ‘trace_e1000e_rx_rss_ip6’:
./trace/generated-tracers.h:8379:431: error: expected string literal before ‘_SDT_ASM_OPERANDS_ipv6_enabled’
./trace/generated-tracers.h:8379:431: error: implicit declaration of function ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=implicit-function-declaration]
./trace/generated-tracers.h:8379:431: error: nested extern declaration of ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=nested-externs]
cc1: all warnings being treated as errors
make: *** [util/oslib-posix.o] Error 1
make: *** Waiting for unfinished jobs....
In file included from ./trace/generated-tracers.h:9:0,
from /home/travis/build/qemu/qemu/include/trace.h:4,
from util/hbitmap.c:16:
./trace/generated-ust-provider.h:16556:3: error: unknown type name ‘_TP_EXPROTO_Bool’
In file included from /home/travis/build/qemu/qemu/include/trace.h:4:0,
from util/hbitmap.c:16:
./trace/generated-tracers.h: In function ‘trace_e1000e_rx_rss_ip6’:
./trace/generated-tracers.h:8379:431: error: expected string literal before ‘_SDT_ASM_OPERANDS_ipv6_enabled’
./trace/generated-tracers.h:8379:431: error: implicit declaration of function ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=implicit-function-declaration]
./trace/generated-tracers.h:8379:431: error: nested extern declaration of ‘__tracepoint_cb_qemu___e1000e_rx_rss_ip6’ [-Werror=nested-externs]
cc1: all warnings being treated as errors
make: *** [util/hbitmap.o] Error 1
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Message-id: 1464894748-27803-1-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Drop the old SysBus init function and use instance_init
* Move AUD_open_in / AUD_open_out function into realize stage
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1463111220-30335-5-git-send-email-zxq_yx_007@163.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Drop the old SysBus init function and use instance_init
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 1463111220-30335-2-git-send-email-zxq_yx_007@163.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit "ca58b45 ui/virtio-gpu: add and use qemu_create_displaysurface_pixman"
breaks scanouts which use a region of the underlying resource only.
So, we need another way to handle the underlying issue. Lets create a
new pixman image, grab a reference on the pixman providing the
underlying storage, hook up a destroy callback which releases the
reference. That way regions work again and releasing the backing
storage should still be impossible thanks to the extra reference we are
holding.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1464597655-26341-1-git-send-email-kraxel@redhat.com
Version: GnuPG v1
iQEcBAABAgAGBQJXT9DWAAoJEO8Ells5jWIRgFAH/1ZDXm8V523AMDOEvBAWgqur
Dj8ZaIwFkqJp7xtLdhS0yKF3xW+vtgx9k+Qftk0S8qEiFKPbThR8iB5VNuesErwd
AZhWo4bnVhKwtWyMw3BDRDK1N4huAWPMZEva1xovR/Cc9v5IG5mx57/K3Zz5C8ec
Jsn4DsLKN0q7W0D0dlnbEOkSjl6iKJchvfPCR6UfvrU7BxfXaCZ9Z7Sfh8ec6tfr
iMgcV9u3A3Zs72gTM9/jdKx8vOrWtdKJufJ8s2Bctc7CyfBNWwnV8PjndhEe3Xvs
vlYeJopdpDPsdMkMtYD6cevtEgvD5yhOBndJ7et807jjuCvUf837tMhodKkFk9M=
=SjIZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 02 Jun 2016 07:23:18 BST using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request: (31 commits)
Add ENET device to i.MX6 SOC.
Add ENET/Gbps Ethernet support to FEC device
i.MX: move FEC device to a register array structure.
i.MX: Rename i.MX FEC defines to ENET_XXX
i.MX: reset TX/RX descriptors when FEC is disabled.
i.MX: Fix FEC code for ECR register reset value.
i.MX: Fix FEC code for MDIO address selection
i.MX: Fix FEC code for MDIO operation selection
net: handle optional VLAN header in checksum computation.
net: improve UDP/TCP checksum computation.
e1000e: Introduce qtest for e1000e device
net: Introduce e1000e device emulation
e1000: Move out code that will be reused in e1000e
e1000_regs: Add definitions for Intel 82574-specific bits
vmxnet3: Use pci_dma_* API instead of cpu_physical_memory_*
net_pkt: Extend packet abstraction as required by e1000e functionality
rtl8139: Move more TCP definitions to common header
net_pkt: Name vmxnet3 packet abstractions more generic
vmxnet3: Use common MAC address tracing macros
net: Add macros for MAC address tracing
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the ENET device to the i.MX6 SOC.
This was tested by booting Linux on an Qemu i.MX6 instance and accessing
the internet from the linux guest.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The ENET device (present in i.MX6) is "derived" from FEC and backward
compatible with it.
This patch adds the necessary support of the added feature in the ENET
device to allow Linux to use it (on supported processors).
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This is to prepare for the ENET Gb device of the i.MX6.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the FEC chapter of i.MX25 reference manual
RX adn TX descriptors are reseted when the FEC device is disabled through ECR.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the FEC chapter of i.MX25 reference manual ECR register is
initialized at 0xf0000000 at reset time.
We fix the value.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
