The PRP and SGL mapping functions does not have any particular need for
the entire NvmeRequest as a parameter. Clean it up.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Dataset Management is not subject to MDTS, but exceeded a certain size
per range causes internal looping. Report this limit (DMRSL) in the NVM
command set specific identify controller data structure.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a trace event for the Identify command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
ZASL (Zone Append Size Limit) is defined exactly like MDTS (Maximum Data
Transfer Size), that is, it is a value in units of the minimum memory
page size (CAP.MPSMIN) and is reported as a power of two.
The 'mdts' nvme device parameter is specified as in the spec, but the
'zoned.append_size_limit' parameter is specified in bytes. This is
suboptimal for a number of reasons:
1. It is just plain confusing wrt. the definition of mdts.
2. There is a lot of complexity involved in validating the value; it
must be a power of two, it should be larger than 4k, if it is zero
we set it internally to mdts, but still report it as zero.
3. While "hw/block/nvme: improve invalid zasl value reporting"
slightly improved the handling of the parameter, the validation is
still wrong; it does not depend on CC.MPS, it depends on
CAP.MPSMIN. And we are not even checking that it is actually less
than or equal to MDTS, which is kinda the *one* condition it must
satisfy.
Fix this by defining zasl exactly like mdts and checking the one thing
that it must satisfy (that it is less than or equal to mdts). Also,
change the default value from 128KiB to 0 (aka, whatever mdts is).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for using the broadcast nsid to issue a flush on all
namespaces through a single command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for TP 4065a ("Simple Copy Command"), v2020.05.04
("Ratified").
The implementation uses a bounce buffer to first read in the source
logical blocks, then issue a write of that bounce buffer. The default
maximum number of source logical blocks is 128, translating to 512 KiB
for 4k logical blocks which aligns with the default value of MDTS.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Refactor the zone write check logic such that the most "meaningful"
error is returned first. That is, first, if the zone is not writable,
return an appropriate status code for that. Then, make sure we are
actually writing at the write pointer and finally check that we do not
cross the zone write boundary. This aligns with the "priority" of status
codes for zone read checks.
Also add a couple of additional descriptive trace events and remove an
always true assert.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implement v1.4 logic for configuring the Controller Memory Buffer. By
default, the v1.4 scheme will be used (CMB must be explicitly enabled by
the host), so drivers that only support v1.3 will not be able to use the
CMB anymore.
To retain the v1.3 behavior, set the boolean 'legacy-cmb' nvme device
parameter.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Padmakar Kalghatgi <p.kalghatgi@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add the size of the mmio read/write to the trace event.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The zoned command set specification states that "All logical blocks in a
zone *shall* be marked as deallocated when [the zone is reset]". Since
the device guarantees 0x00 to be read from deallocated blocks we have to
issue a pwrite_zeroes since we cannot be sure that a discard will do
anything. But typically, this will be achieved with an efficient
unmap/discard operation.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Zone Descriptor Extension is a label that can be assigned to a zone.
It can be set to an Empty zone and it stays assigned until the zone
is reset.
This commit adds a new optional module property,
"zoned.descr_ext_size". Its value must be a multiple of 64 bytes.
If this value is non-zero, it becomes possible to assign extensions
of that size to any Empty zones. The default value for this property
is 0, therefore setting extensions is disabled by default.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add two module properties, "zoned.max_active" and "zoned.max_open"
to control the maximum number of zones that can be active or open.
Once these variables are set to non-default values, these limits are
checked during I/O and Too Many Active or Too Many Open command status
is returned if they are exceeded.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The emulation code has been changed to advertise NVM Command Set when
"zoned" device property is not set (default) and Zoned Namespace
Command Set otherwise.
Define values and structures that are needed to support Zoned
Namespace Command Set (NVMe TP 4053) in PCI NVMe controller emulator.
Define trace events where needed in newly introduced code.
In order to improve scalability, all open, closed and full zones
are organized in separate linked lists. Consequently, almost all
zone operations don't require scanning of the entire zone array
(which potentially can be quite large) - it is only necessary to
enumerate one or more zone lists.
Handlers for three new NVMe commands introduced in Zoned Namespace
Command Set specification are added, namely for Zone Management
Receive, Zone Management Send and Zone Append.
Device initialization code has been extended to create a proper
configuration for zoned operation using device properties.
Read/Write command handler is modified to only allow writes at the
write pointer if the namespace is zoned. For Zone Append command,
writes implicitly happen at the write pointer and the starting write
pointer value is returned as the result of the command. Write Zeroes
handler is modified to add zoned checks that are identical to those
done as a part of Write flow.
Subsequent commits in this series add ZDE support and checks for
active and open zone limits.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Define the structures and constants required to implement
Namespace Types support.
Namespace Types introduce a new command set, "I/O Command Sets",
that allows the host to retrieve the command sets associated with
a namespace. Introduce support for the command set and enable
detection for the NVM Command Set.
The new workflows for identify commands rely heavily on zero-filled
identify structs. E.g., certain CNS commands are defined to return
a zero-filled identify struct when an inactive namespace NSID
is supplied.
Add a helper function in order to avoid code duplication when
reporting zero-filled identify structures.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This log page becomes necessary to implement to allow checking for
Zone Append command support in Zoned Namespace Command Set.
This commit adds the code to report this log page for NVM Command
Set only. The parts that are specific to zoned operation will be
added later in the series.
All incoming admin and i/o commands are now only processed if their
corresponding support bits are set in this log. This provides an
easy way to control what commands to support and what not to
depending on set CC.CSS.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Move write processing to nvme_do_write() that now handles both WRITE
and WRITE ZEROES. Both nvme_write() and nvme_write_zeroes() become
inline helper functions.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The majority of code in nvme_rw() is becoming read- or write-specific.
Move these parts to two separate handlers, nvme_read() and nvme_write()
to make the code more readable and to remove multiple is_write checks
that has been present in the i/o path.
This is a refactoring patch, no change in functionality.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add the Compare command.
This implementation uses a bounce buffer to read in the data from
storage and then compare with the host supplied buffer.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for reporting the Deallocated or Unwritten Logical Block
Error (DULBE).
Rely on the block status flags reported by the block layer and consider
any block with the BDRV_BLOCK_ZERO flag to be deallocated.
Multiple factors affect when a Write Zeroes command result in
deallocation of blocks.
* the underlying file system block size
* the blockdev format
* the 'discard' and 'logical_block_size' parameters
format | discard | wz (512B) wz (4KiB) wz (64KiB)
-----------------------------------------------------
qcow2 ignore n n y
qcow2 unmap n n y
raw ignore n y y
raw unmap n y y
So, this works best with an image in raw format and 4KiB LBAs, since
holes can then be punched on a per-block basis (this assumes a file
system with a 4kb block size, YMMV). A qcow2 image, uses a cluster size
of 64KiB by default and blocks will only be marked deallocated if a full
cluster is zeroed or discarded. However, this *is* consistent with the
spec since Write Zeroes "should" deallocate the block if the Deallocate
attribute is set and "may" deallocate if the Deallocate attribute is not
set. Thus, we always try to deallocate (the BDRV_REQ_MAY_UNMAP flag is
always set).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Address 0 is not an invalid address. Remove those invalikd checks.
Unaligned PRP2 and PRP list entries should result in Invalid PRP Offset
status code and not Invalid Field. Fix that.
See NVMe Express v1.3d, Section 4.3 ("Physical Region Page Entry and
List").
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
If a command results in a non-zero status code, trace it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Include the namespace id in the pci_nvme_{get,set}feat trace events.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Fail to start the controller if the user requests a command set that the
controller does not support.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The code switches on the opcode to invoke a function specific to that
opcode. There's no point in consolidating back to a common function that
just switches on that same opcode without any actual common code.
Restore the opcode specific behavior without going back through another
level of switches.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This adds support for multiple namespaces by introducing a new 'nvme-ns'
device model. The nvme device creates a bus named from the device name
('id'). The nvme-ns devices then connect to this and registers
themselves with the nvme device.
This changes how an nvme device is created. Example with two namespaces:
-drive file=nvme0n1.img,if=none,id=disk1
-drive file=nvme0n2.img,if=none,id=disk2
-device nvme,serial=deadbeef,id=nvme0
-device nvme-ns,drive=disk1,bus=nvme0,nsid=1
-device nvme-ns,drive=disk2,bus=nvme0,nsid=2
The drive property is kept on the nvme device to keep the change
backward compatible, but the property is now optional. Specifying a
drive for the nvme device will always create the namespace with nsid 1.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
For now, support the Data Block, Segment and Last Segment descriptor
types.
See NVM Express 1.3d, Section 4.4 ("Scatter Gather List (SGL)").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
This pulls block layer aio submission/completion to common functions.
For completions, additionally map an AIO error to the Unrecovered Read
and Write Fault status codes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the symbolic command name to the pci_nvme_{io,admin}_cmd and
pci_nvme_rw trace events.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Handling DMA errors gracefully is required for the device to pass the
block/011 test ("disable PCI device while doing I/O") in the blktests
suite.
With this patch the device sets the Controller Fatal Status bit in the
CSTS register when failing to read from a submission queue or writing to
a completion queue; expecting the host to reset the controller.
If DMA errors occur at any other point in the execution of the command
(say, while mapping the PRPs), the command is aborted with a Data
Transfer Error status code.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Fix a typo in the sq doorbell trace event.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of scripts/cleanup-trace-events.pl. Funnies
requiring manual post-processing:
* accel/tcg/cputlb.c trace points are in trace-events.
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* hw/tpm/tpm_spapr.c uses pseudo trace point tpm_spapr_show_buffer to
guard debug code.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* linux-user/trace-events abbreviates a tedious list of filenames to
*/signal.c.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200806141334.3646302-5-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add 'mdts' device parameter to control the Maximum Data Transfer Size of
the controller and check that it is respected.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add nvme_map_addr, nvme_map_addr_cmb and nvme_addr_to_cmb helpers and
use them in nvme_map_prp.
This fixes a bug where in the case of a CMB transfer, the device would
map to the buffer with a wrong length.
Fixes: b2b2b67a00 ("nvme: Add support for Read Data and Write Data in CMBs.")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Since we are not providing the NGUID or EUI64 fields, we must support
the Namespace UUID. We do not have any way of storing a persistent
unique identifier, so conjure up a UUID that is just the namespace id.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-15-its@irrelevant.dk>
Since the device does not have any persistent state storage, no
features are "saveable" and setting the Save (SV) field in any Set
Features command will result in a Feature Identifier Not Saveable status
code.
Similarly, if the Select (SEL) field is set to request saved values, the
devices will (as it should) return the default values instead.
Since this also introduces "Supported Capabilities", the nsid field is
now also checked for validity wrt. the feature being get/set'ed.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-13-its@irrelevant.dk>
Add support for the Asynchronous Event Request command. Required for
compliance with NVMe revision 1.3d. See NVM Express 1.3d, Section 5.2
("Asynchronous Event Request command").
Mostly imported from Keith's qemu-nvme tree. Modified with a max number
of queued events (controllable with the aer_max_queued device
parameter). The spec states that the controller *should* retain
events, so we do best effort here.
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-9-its@irrelevant.dk>
Add support for the Get Log Page command and basic implementations of
the mandatory Error Information, SMART / Health Information and Firmware
Slot Information log pages.
In violation of the specification, the SMART / Health Information log
page does not persist information over the lifetime of the controller
because the device has no place to store such persistent state.
Note that the LPA field in the Identify Controller data structure
intentionally has bit 0 cleared because there is no namespace specific
information in the SMART / Health information log page.
Required for compliance with NVMe revision 1.3d. See NVM Express 1.3d,
Section 5.14 ("Get Log Page command").
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-8-its@irrelevant.dk>
Add various additional tracing and streamline nvme_identify_ns and
nvme_identify_nslist (they do not need to repeat the command, it is
already in the trace name).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-4-its@irrelevant.dk>
Change the prefix of all nvme device related trace events to 'pci_nvme'
to not clash with trace events from the nvme block driver.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-3-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch introduces support for PMR that has been defined as part of NVMe 1.4
spec. User can now specify a pmrdev option that should point to HostMemoryBackend.
pmrdev memory region will subsequently be exposed as PCI BAR 2 in emulated NVMe
device. Guest OS can perform mmio read and writes to the PMR region that will stay
persistent across system reboot.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200330164656.9348-1-andrzej.jakowski@linux.intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The given argument for this trace should be cqid, not sqid.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Message-Id: <20200324140646.8274-1-minwoo.im.dev@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
While at it, add some trace messages to help debug problems
seen when running the latest Linux kernel.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since not all trace backends support dynamic field width in
format (dtrace via stap does not), replace by a static field
width instead.
We previously passed to the trace API 'width << 1' as the number
of hex characters to display (the dynamic field width). We don't
need this anymore. Instead, display the size of bytes accessed.
Fixes: e8aa2d95ea ("pflash: Simplify trace_pflash_io_read/write")
Fixes: c1474acd5d ("pflash: Simplify trace_pflash_data_read/write")
Reported-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Buglink: https://bugs.launchpad.net/qemu/+bug/1844817
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Use a field width format to have a single function to log
the different width accesses.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-4-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Call the read() trace function after the value is set, so we can
log the returned value.
Rename the I/O trace functions with '_io_' in their name.
Reviewed-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190627202719.17739-3-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kenneth Heitke <kenneth.heitke@intel.com>
Reviewed-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
