Rework HWC handling to simplify it and fix cursor not updating on
screen as needed. Previously cursor was not updated because checking
for changes in a line overrode the update flag set for the cursor but
fixing this is not enough because the cursor should also be updated if
its shape or location changes. Introduce hwc_invalidate() function to
handle that similar to other display controller models.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 6970a5e9868b7246656c1d02038dc5d5fa369507.1492787889.git.balaton@eik.bme.hu
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We only emulate the sysbus device in its default LE mode and PCI is LE
as well so specify this for registers and framebuffer memory.
Note that though the Linux kernel driver has code which claims to
handle both big and little endian, it is obviously bogus for 16 bit
and cannot be trusted as a source of information on the framebuffer
pixel format. This is our best guess about device behaviour based on
the specs and testing with MorphOS that is known to work on real HW.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 8b9605a569f8bf54074e15903620b18cd9967c89.1492787889.git.balaton@eik.bme.hu
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only the display controller part is created automatically on PCI
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 647d292c6f5abba8b2a614687229949b5dcb864e.1492787889.git.balaton@eik.bme.hu
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do not use the base address to access data in local memory. This is in
preparation to allow chip connected via PCI where base address depends
on where the BAR is mapped so it will be unknown.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 79dab21bc6ec4d563aabf265c3bab40e2e95aae8.1492787889.git.balaton@eik.bme.hu
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adding vmstate saving is not in this patch because the state structure
will be changed in further patches, then another patch will add
vmstate descriptor after those changes.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: a32b7fc981a20205f96d530d8e958f12ace1104c.1492787889.git.balaton@eik.bme.hu
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add properties for the default display resolution, pass
on that information to the guest so the driver can use it.
Also move up qxl_crc32() function so we don't need a
forward declaration.
Additionally guest driver updates are needed so the
guest driver will actually pick this up, which will
probably land in linux kernel 4.12.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20170421092234.8368-1-kraxel@redhat.com
Fix standard vga mode check: Both s->config and s->enabled must be set
to enable vmware command fifo processing.
Drop dirty tracking code from the fifo rendering code path, it isn't
used anyway because vmsvga turns off dirty tracking when leaving
standard vga mode.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20170421091632.30900-9-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The vga code clears the dirty bits *after* reading the framebuffer
memory. So if the guest framebuffer updates hits the race window
between vga reading the framebuffer and vga clearing the dirty bits
vga will miss that update
Fix it by using the new memory_region_copy_and_clear_dirty()
memory_region_copy_get_dirty() functions. That way we clear the
dirty bitmap before reading the framebuffer. Any guest display
updates happening in parallel will be properly tracked in the
dirty bitmap then and the next display refresh will pick them up.
Problem triggers with mttcg only. Before mttcg was merged tcg
never ran in parallel to vga emulation. Using kvm will hide the
problem too, due to qemu operating on a userspace copy of the
kernel's dirty bitmap.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20170421091632.30900-5-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add vga_scanline_invalidated helper to check whenever a scanline was
invalidated. Add a sanity check to fix OOB read access for display
heights larger than 2048.
Only cirrus uses this, for hardware cursor rendering, so having this
work properly for the first 2048 scanlines only shouldn't be a problem
as the cirrus can't handle large resolutions anyway. Also changing the
invalidated_y_table size would break live migration.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20170421091632.30900-4-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This avoids a "#ifdef HOST_WORDS_BIGENDIAN" and this is the purpose
of PIXMAN_BE_* macros.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sahid Orentino Ferdjaoui <sahid.ferdjaoui@redhat.com>
Message-id: 20170403114044.15762-1-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Previous to the existence of load_image_mr(), the only way to load in the
FCode ROM image was to pass in its physical address via qdev properties
and use load_image_targphys().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Rather than calling memory_region_set_dirty() directly, make sure that we call
tcx_set_dirty() instead. This ensures that the 24-bit plane and cplane are
also invalidated correctly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
As all surfaces in QEMU are now either shared or 32-bit ARGB regardless of
the guest depth, remove all non-32-bit primitives from tcx_update_display()
and consequence their implementation which are no longer required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Now that page alignment is handled by the memory API, there is no need to
duplicate the code 4 times (4 * 1024 == 4096 == TARGET_PAGE_SIZE).
Finally we have now removed all traces of TARGET_PAGE_SIZE.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Now that page alignment is handled by the memory API, there is no need to
duplicate the code 4 times (4 * 1024 == 4096 == TARGET_PAGE_SIZE).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Since all of the tcx_*_dirty() functions now calculate the 24-bit and
cplane offsets themselves from the base address, these variables are no
longer needed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
This can now be used by both the 8-bit and 24-bit display code, so rename
to tcx_check_dirty().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
This can now be used by both the 8-bit and 24-bit display code, so rename
to tcx_check_dirty().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Previous to the existence of load_image_mr(), the only way to load in the
FCode ROM image was to pass in its physical address via qdev properties
and use load_image_targphys().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The code was incorrectly calculating the end address rather than the size of
the required region.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
This was an artifact from very early versions of the code from before the
memory API and is no longer needed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Since commit cd958edb1f, same size console resize is skipped. This
change broke QXL incoming migration in VGA mode,
qemu_spice_display_switch() is no longer called during qxl_post_load(),
because default message surface is of the same size, and during
displaychangelistener registration, PCIQXLDevice.mode is
QXL_MODE_UNDEFINED. This triggers a later crash on refresh:
==2634== Invalid read of size 4
==3516== at 0x65F3050: pixman_image_get_data (in /usr/lib64/libpixman-1.so.0.34.0)
==3516== by 0x6F0CEB: qemu_spice_create_update (spice-display.c:215)
==3516== by 0x6F1CC7: qemu_spice_display_refresh (spice-display.c:502)
==3516== by 0x58CF77: display_refresh (qxl.c:1948)
==3516== by 0x6E8084: do_safe_dpy_refresh (console.c:1591)
==3516== by 0x6E80D5: dpy_refresh (console.c:1604)
==3516== by 0x6E4508: gui_update (console.c:201)
==3516== by 0x81898E: timerlist_run_timers (qemu-timer.c:536)
==3516== by 0x8189D6: qemu_clock_run_timers (qemu-timer.c:547)
==3516== by 0x818D98: qemu_clock_run_all_timers (qemu-timer.c:662)
==3516== by 0x81952A: main_loop_wait (main-loop.c:514)
==3516== by 0x4ADD29: main_loop (vl.c:1898)
One way to solve this is to explicitely call qemu_spice_display_switch()
on entering VGA mode, which is called during qxl_post_load().
Fixes:
"null pointer access on migration resume of systemrescuecd boot menu with qxl-vga"
https://bugs.launchpad.net/qemu/+bug/1679126https://bugzilla.redhat.com/show_bug.cgi?id=1438566
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20170406120513.638-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Should be "c" not "col". The macro is used with "col" as third parameter
everywhere, so this tyops doesn't break something.
Fixes: 026aeffcb4
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1490168303-24588-1-git-send-email-kraxel@redhat.com
... and drop OPENGL_CFLAGS from Makefiles.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1490079888-29029-1-git-send-email-kraxel@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change Makefile.objs to use CONFIG_XEN instead of CONFIG_XEN_BACKEND, so
that the Xen backends are only built for targets that support Xen.
Set CONFIG_XEN in the toplevel Makefile to ensure that files that are
built only once pick up Xen support properly.
Signed-off-by: Stefano Stabellini <stefano@aporeto.com>
Tested-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
CC: pbonzini@redhat.com
CC: peter.maydell@linaro.org
CC: rth@twiddle.net
CC: stefanha@redhat.com
Message-Id: <1489694518-16978-1-git-send-email-sstabellini@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The switch from pointers to addresses (commit
026aeffcb4 and
ffaf857778) added
a off-by-one bug to 16bit backward blits. Fix.
Reported-by: 李强 <liqiang6-s@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Li Qiang <liqiang6-s@360.cn>
Message-id: 1489735296-19047-1-git-send-email-kraxel@redhat.com
Does basically the same as "cirrus: stop passing around dst pointers in
the blitter", just for the src pointer instead of the dst pointer.
For the src we have to care about cputovideo blits though and fetch the
data from s->cirrus_bltbuf instead of vga memory. The cirrus_src*()
helper functions handle that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489584487-3489-1-git-send-email-kraxel@redhat.com
Instead pass around the address (aka offset into vga memory). Calculate
the pointer in the rop_* functions, after applying the mask to the
address, to make sure the address stays within the valid range.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489574872-8679-1-git-send-email-kraxel@redhat.com
off_cur_end is exclusive, so off_cur_end == cirrus_addr_mask is valid.
Fix calculation to make sure to allow that, otherwise the assert added
by commit f153b563f8 can trigger for valid
blits.
Test case: boot windows nt 4.0
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489579606-26020-1-git-send-email-kraxel@redhat.com
Ok, we have this beast in the cirrus code which is not used at all by
modern guests, except when you try to find security holes in qemu. So,
add an option to disable blitter altogether. Guests released within
the last ten years should not show any rendering issues if you turn off
blitter support.
There are no known bugs in the cirrus blitter code. But in the past we
hoped a few times already that we've finally nailed the last issue. So
having some easy way to mitigate in case yet another blitter issue shows
up certainly makes me sleep a bit better at night.
For completeness: The by far better way to mitigate is to switch away
from cirrus and use stdvga instead. Or something more modern like
virtio-vga in case your guest has support for it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489494540-15745-1-git-send-email-kraxel@redhat.com
Quoting cirrus source code:
Follow real hardware, cirrus card emulated has 4 MB video memory.
Also accept 8 MB/16 MB for backward compatibility.
So just use 4MB by default. We decided to leave that at 8MB by default
a while ago, for live migration compatibility reasons. But we have
compat properties to handle that, so that isn't a compeling reason.
This also removes some sanity check inconsistencies in the cirrus code.
Some places check against the allocated video memory, some places check
against the 4MB physical hardware has. Guest code can trigger asserts
because of that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489494514-15606-1-git-send-email-kraxel@redhat.com
There is a special code path (dpy_gfx_copy) to allow graphic emulation
notify user interface code about bitblit operations carryed out by
guests. It is supported by cirrus and vnc server. The intended purpose
is to optimize display scrolls and just send over the scroll op instead
of a full display update.
This is rarely used these days though because modern guests simply don't
use the cirrus blitter any more. Any linux guest using the cirrus drm
driver doesn't. Any windows guest newer than winxp doesn't ship with a
cirrus driver any more and thus uses the cirrus as simple framebuffer.
So this code tends to bitrot and bugs can go unnoticed for a long time.
See for example commit "3e10c3e vnc: fix qemu crash because of SIGSEGV"
which fixes a bug lingering in the code for almost a year, added by
commit "c7628bf vnc: only alloc server surface with clients connected".
Also the vnc server will throttle the frame rate in case it figures the
network can't keep up (send buffers are full). This doesn't work with
dpy_gfx_copy, for any copy operation sent to the vnc client we have to
send all outstanding updates beforehand, otherwise the vnc client might
run the client side blit on outdated data and thereby corrupt the
display. So this dpy_gfx_copy "optimization" might even make things
worse on slow network links.
Lets kill it once for all.
Oh, and one more reason: Turns out (after writing the patch) we have a
security bug in that code path ...
Fixes: CVE-2016-9603
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1489494419-14340-1-git-send-email-kraxel@redhat.com
check the validity of parameters in cirrus_bitblt_rop_fwd_transp_xxx
and cirrus_bitblt_rop_fwd_xxx to avoid the OOB read which causes qemu Segmentation fault.
After the fix, we will touch the assert in
cirrus_invalidate_region:
assert(off_cur_end >= off_cur);
Signed-off-by: fangying <fangying1@huawei.com>
Signed-off-by: hangaohuai <hangaohuai@huawei.com>
Message-id: 20170314063919.16200-1-hangaohuai@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Make sure we don't leave guest_cursor pointing into nowhere. This might
lead to (rare) live migration failures, due to target trying to restore
the cursor from the stale pointer.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1421788
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1488789111-27340-1-git-send-email-kraxel@redhat.com
Don't truncate the multiplication and do a 64 bit one instead
because the result is stored in a 64 bit variable.
This fixes a similar coverity warning to commits 237a8650d6 and
4382fa6554, in a similar way, and is the final third of the fix for
coverity CID 1167561 (hopefully!).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We'll add a variant which accepts dmabufs soon. Change
the name so we can easily disturgish the two variants.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1487669841-13668-2-git-send-email-kraxel@redhat.com
CIRRUS_BLTMODE_MEMSYSSRC blits do NOT check blit destination
and blit width, at all. Oops. Fix it.
Security impact: high.
The missing blit destination check allows to write to host memory.
Basically same as CVE-2014-8106 for the other blit variants.
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This reverts commit 5858dd1801.
Conflicts:
hw/display/cirrus_vga.c
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 1486645341-5010-2-git-send-email-kraxel@redhat.com
The blit_region_is_unsafe checks don't work correctly for the
patterncopy source. It's a fixed-sized region, which doesn't
depend on cirrus_blt_{width,height}. So go do the check in
cirrus_bitblt_common_patterncopy instead, then tell blit_is_unsafe that
it doesn't need to verify the source. Also handle the case where we
blit from cirrus_bitbuf correctly.
This patch replaces 5858dd1801.
Security impact: I think for the most part error on the safe side this
time, refusing blits which should have been allowed.
Only exception is placing the blit source at the end of the video ram,
so cirrus_blt_srcaddr + 256 goes beyond the end of video memory. But
even in that case I'm not fully sure this actually allows read access to
host memory. To trick the commit 5858dd18 security checks one has to
pick very small cirrus_blt_{width,height} values, which in turn implies
only a fraction of the blit source will actually be used.
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 1486645341-5010-1-git-send-email-kraxel@redhat.com
When the guest sends VIRTIO_GPU_CMD_RESOURCE_UNREF without detaching the
backing storage beforehand (VIRTIO_GPU_CMD_RESOURCE_DETACH_BACKING)
we'll leak memory.
This patch fixes it for 3d mode, simliar to the 2d mode fix in commit
"b8e2392 virtio-gpu: call cleanup mapping function in resource destroy".
Reported-by: 李强 <liqiang6-s@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485167210-4757-1-git-send-email-kraxel@redhat.com
In virtio_gpu_set_scanout function, when creating the 'rect'
its refcount is set to 2, by pixman_image_create_bits and
qemu_create_displaysurface_pixman function. This can lead
a memory leak issues. This patch avoid this issue.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 5884626f.5b2f6b0a.1bfff.3037@mx.google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When doing bitblt copy in backward mode, we should minus the
blt width first just like the adding in the forward mode. This
can avoid the oob access of the front of vga's vram.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
{ kraxel: with backward blits (negative pitch) addr is the topmost
address, so check it as-is against vram size ]
Cc: qemu-stable@nongnu.org
Cc: P J P <ppandit@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Fixes: d3532a0db0 (CVE-2014-8106)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485938101-26602-1-git-send-email-kraxel@redhat.com
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Apply the cirrus_addr_mask to cirrus_blt_dstaddr and cirrus_blt_srcaddr
right after assigning them, in cirrus_bitblt_start(), instead of having
this all over the place in the cirrus code, and missing a few places.
Reported-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485338996-17095-1-git-send-email-kraxel@redhat.com
The rops used by cirrus_bitblt_common_patterncopy only use
the destination pitch, so the source pitch shoul allowed to
be zero and the blit with used for the range check around the
source address.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Message-id: 1485272138-23249-1-git-send-email-w.bumiller@proxmox.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
cirrus_invalidate_region() calls memory_region_set_dirty()
on a per-line basis, always ranging from off_begin to
off_begin+bytesperline. With a negative pitch off_begin
marks the top most used address and thus we need to do an
initial shift backwards by a line for negative pitches of
backward blits, otherwise the first iteration covers the
line going from the start offset forwards instead of
backwards.
Additionally since the start address is inclusive, if we
shift by a full `bytesperline` we move to the first address
*not* included in the blit, so we only shift by one less
than bytesperline.
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Message-id: 1485352137-29367-1-git-send-email-w.bumiller@proxmox.com
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There are a number of unused trace events that
scripts/cleanup-trace-events.pl finds. The "hw/vfio/pci-quirks.c"
filename was typoed and "qapi/qapi-visit-core.c" was missing the qapi/
directory prefix.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170126171613.1399-3-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We are switching BUILD_BUG_ON to verify that it's parameter is a
compile-time constant, and it turns out that some gcc versions
(specifically gcc (Ubuntu 5.4.0-6ubuntu1~16.04.4) 5.4.0 20160609) are
not smart enough to figure it out for expressions involving local
variables. This is harmless but means that the check is ineffective for
these platforms. To fix, replace variables with macros.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Coverity points out that calculating src_len by multiplying
src_width by rows could overflow. This can only happen in
the implausible case of a framebuffer larger than 4GB, but
we may as well fix it, placating Coverity. (CID1005515)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Don't truncate the multiplication and do a 64 bit one instead
because the result is stored in a 64 bit variable.
This fixes a similar coverity warning to commit 237a8650d6,
in a similar way, and is the other half of the fix for
coverity CID 1167561.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If a migration is already in progress and somebody attempts
to add a migration blocker, this should rightly fail.
Add an errp parameter and a retcode return value to migrate_add_blocker.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Ashijeet Acharya <ashijeetacharya@gmail.com>
Message-Id: <1484566314-3987-5-git-send-email-ashijeetacharya@gmail.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Merged with recent 'Allow invtsc migration' change
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Coverity points out that if we fail in the "creating resources"
loop in virtio_gpu_load() we will leak various resources (CID 1356431).
Failing a VM load is going to leave the simulation in a complete mess,
but we can tidy up to the point that a full system reset should
get us back to sanity.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483969123-14839-3-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The 'hostmem' field in VirtIOGPU is used to track the total memory
used in pixmaps so that we can impose a maximum limit on it.
However this field is neither migrated nor recalculated on
VM load, which means that after a migration it will be incorrectly
too low, which can allow the guest to use more pixmap memory
than it should. The per-resource hostmem fields are not filled
in either as we reallocate them in the load function.
Recalculate the memory used for each pixmap and the total memory
used as we reallocate the pixmaps in virtio_gpu_load().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1483969123-14839-2-git-send-email-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 4299b90 added a check which is too broad, given that the source
pitch value is not required to be initialized for solid fill operations.
This patch refines the blit_is_unsafe() check to ignore source pitch in
that case. After applying the above commit as a security patch, we
noticed the SLES 11 SP4 guest gui failed to initialize properly.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Message-id: 20170109203520.5619-1-brogers@suse.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In virgl_cmd_get_capset function, it uses g_malloc to allocate
a response struct to the guest. As the 'resp'struct hasn't been full
initialized it will lead the 'resp->padding' field to the guest.
Use g_malloc0 to avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 58188cae.4a6ec20a.3d2d1.aff2@mx.google.com
[ kraxel: resolved conflict ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the resource attach backing function, everytime it will
allocate 'res->iov' thus can leading a memory leak. This
patch avoid this.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Message-id: 1483003721-65360-1-git-send-email-liq3ea@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the virgl_renderer_resource_attach_iov function fails the
'res_iovs' will be leaked. Add check of the return value to
free the 'res_iovs' when failing.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1482999086-59795-1-git-send-email-liq3ea@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the guest destroy the resource before detach banking, the 'iov'
and 'addrs' field in resource is not freed thus leading memory
leak issue. This patch avoid this.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1480386565-10077-1-git-send-email-liq3ea@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch makes virtio-gpu track host memory allocations for ressources
and applies a limit (configurable 256M by default). When exceeding the
limit virtio-gpu throws VIRTIO_GPU_RESP_ERR_OUT_OF_MEMORY errors (like
it already does today when pixman image allocations fail).
This patch covers 2d mode only. For 3d mode we have to figure how we
are going to handle this best. qemu doesn't track resources in case
virglrenderer is used, so I guess we should extend virglrenderer to
allow setting a limit, then let qemu set the limit and catch
virgl_renderer_resource_create failures.
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: 李强 <liqiang6-s@360.cn>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1480423356-22255-1-git-send-email-kraxel@redhat.com
Virtio GPU device while processing 'VIRTIO_GPU_CMD_GET_CAPSET'
command, retrieves the maximum capabilities size to fill in the
response object. It continues to fill in capabilities even if
retrieved 'max_size' is zero(0), thus resulting in OOB access.
Add check to avoid it.
Reported-by: Zhenhao Hong <zhenhaohong@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20161214070156.23368-1-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In Cirrus CLGD 54xx VGA Emulator, if cirrus graphics mode is VGA,
'cirrus_get_bpp' returns zero(0), which could lead to a divide
by zero error in while copying pixel data. The same could occur
via blit pitch values. Add check to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476776717-24807-1-git-send-email-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In update_cursor_data_virgl function, if the 'width'/ 'height'
is not equal to current cursor's width/height it will return
without free the 'data' allocated previously. This will lead
a memory leak issue. This patch fix this issue.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-id: 58187760.41d71c0a.cca75.4cb9@mx.google.com
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In virgl_cmd_get_capset_info dispatch function, the 'resp' hasn't
been full initialized before writing to the guest. This will leak
the 'resp.padding' and 'resp.hdr.padding' fieds to the guest. This
patch fix this issue.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Message-id: 5818661e.0860240a.77264.7a56@mx.google.com
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Currently if the client keeps sending the same monitor config to
QEMU/spice-server, QEMU will always raise
a QXL_INTERRUPT_CLIENT_MONITORS_CONFIG regardless of whether there was a
change or not.
Guest-side (with fedora 25), the kernel QXL KMS driver will also forward the
event to user-space without checking if there were actual changes.
Next in line are gnome-shell/mutter (on a default f25 install), which
will try to reconfigure everything without checking if there is anything
to do.
Where this gets ugly is that when applying the resolution changes,
gnome-shell/mutter will call drmModeRmFB, drmModeAddFB, and
drmModeSetCrtc, which will cause the primary surface to be destroyed and
recreated by the QXL KMS driver. This in turn will cause the client to
resend a client monitors config message, which will cause QEMU to reemit
an interrupt with an unchanged monitors configuration, ...
This causes https://bugzilla.redhat.com/show_bug.cgi?id=1266484
This commit makes sure that we only emit
QXL_INTERRUPT_CLIENT_MONITORS_CONFIG when there are actual configuration
changes the guest should act on.
Signed-off-by: Christophe Fergeau <cfergeau@redhat.com>
Message-id: 20161028144840.18326-1-cfergeau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Prepare xen_be_find_xendev to be shared with frontends:
* xen_be_find_xendev -> xen_pv_find_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_send_notify to be shared with frontends:
* xen_be_send_notify -> xen_pv_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_unbind_evtchn to be shared with frontends:
* xen_be_unbind_evtchn -> xen_pv_unbind_evtchn
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_printf to be used by both backend and frontends:
* xen_be_printf -> xen_pv_printf
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Fixes:
* WARNING: line over 80 characters
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Fixes the following errors:
* ERROR: line over 90 characters
* ERROR: code indent should never use tabs
* ERROR: space prohibited after that open square bracket '['
* ERROR: do not initialise statics to 0 or NULL
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Don't truncate the multiplication and do a 64 bit one instead because
because the result is stored in a 64 bit variable.
Spotted by coverity, CID 1167561.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
In virtio gpu resource create dispatch, if the pixman format is zero
it doesn't free the resource object allocated previously. Thus leading
a host memory leak issue. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 57df486e.8379240a.c3620.ff81@mx.google.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Drop the old Sysbus init and use instance_init and
DeviceClass::realize instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 20161023091816.3839-5-zxq_yx_007@163.com
[PMM: added accidentally dropped blank line]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now all the usages of the old version of VMSTATE_VIRTIO_DEVICE are gone,
so we can get rid of the conditionals, and the old macro.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use the new VMSTATE_VIRTIO_DEVICE macro. The device virtio-gpu is
special because it actually does not adhere to the virtio migration
schema, because device state is last.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
