The do_cmd variable is only set for the MESSAGE OUT and COMMAND phases i.e.
those which involve transfers from the host to the SCSI bus, and so the unused
case can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The ultimate aim is to for esp_do_dma() behaviour to be determined by the SCSI
bus phase, in which case it is necessary to have separate to/from device paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Invert the logic so that the end of DMA transfer check becomes one that checks
for TC == 0 in the from device path in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This helps to simplify esp_reg_write() and potentially allows for a 2-level
deep FIFO to be implemented in future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This should be exclusively managed by esp_set_tc() rather than being manually
set in multiple places. Start by removing the occurrences exclusive to PDMA
and command completion which are those that can be currently removed without
affecting any test images.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This flag is set once the transfer counter counts down to zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since the DREQ value depends upon the result of the selection process, add a
workaround to each esp_select() to manually assert DREQ durring the MESSAGE OUT
and COMMAND phases.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The FIFO contents should not be affected by performing SCSI target selection.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The fifo8_pop_buf() function returns a pointer to the FIFO buffer up to the
specified length. Since the FIFO buffer is modelled as an array then once
the FIFO wraps around, only the continuous portion of the buffer can be
returned.
In future the use of continuous and unaligned accesses will advance the
internal FIFO head pointer, so modify esp_fifo_pop_buf() to ensure that
any wraparound content is also returned up to the requested length.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Since get_cmd() can be called multiple times during a mixed FIFO/DMA request,
move the existing request cancel check into esp_select() which always occurs
at the start of new SCSI request.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The FIFO contents should not be affected if the target selection fails.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Add a 'current_lun' check for a null value
to avoid null pointer dereferencing and
recover host if NULL return
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4eb8606560 (esp: store lun coming from the MESSAGE OUT phase)
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Message-ID: <20231229152647.19699-1-adiupina@astralinux.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the case where a SCSI layer transfer is incorrectly terminated, it is
possible for a TI command to cause a SCSI buffer overflow due to the
expected transfer data length being less than the available data in the
FIFO. When this occurs the unsigned async_len variable underflows and
becomes a large offset which writes past the end of the allocated SCSI
buffer.
Restrict the non-DMA transfer length to be the smallest of the expected
transfer length and the available FIFO data to ensure that it is no longer
possible for the SCSI buffer overflow to occur.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1810
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230913204410.65650-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The call to esp_dma_enable() was being made with the SYSBUS_ESP type instead of
the ESP type. This meant that when GPIO 1 was being used to trigger a DMA
request from an external DMA controller, the setting of ESPState's dma_enabled
field would clobber unknown memory whilst the dma_cb callback pointer would
typically return NULL so the DMA request would never start.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20230913204410.65650-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Those typos are in files which are used to generate the QEMU manual.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Message-Id: <20221110190825.879620-1-sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
[thuth: update sentence in can.rst as suggested by Peter]
Signed-off-by: Thomas Huth <thuth@redhat.com>
In the SCSI subsystem we currently use the legacy functions
qdev_reset_all() and qbus_reset_all(). These perform a recursive
reset, starting from either a qbus or a qdev. However they do not
permit any of the devices in the tree to use three-phase reset,
because device reset goes through the device_legacy_reset() function
that only calls the single DeviceClass::reset method.
Switch to using the device_cold_reset() and bus_cold_reset()
functions. These also perform a recursive reset, where first the
children are reset and then finally the parent, but they use the new
(...in 2020...) Resettable mechanism, which supports both the old
style single-reset method and also the new 3-phase reset handling.
Since no devices attached to SCSI buses currently try to use 3-phase
reset, this should be a no-behaviour-change commit which just reduces
the use of a deprecated API.
Commit created with:
sed -i -e 's/qdev_reset_all/device_cold_reset/g;s/qbus_reset_all/bus_cold_reset/g' hw/scsi/*.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20221013160623.1296109-2-peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a SCSI command is received from the guest, the CDB length implied
by the first byte might exceed the number of bytes the guest sent. In
this case scsi_req_new() will read uninitialized data, causing
unpredictable behavior.
Adds the buf_len parameter to scsi_req_new() and plumbs it through the
call stack.
Signed-off-by: John Millikin <john@john-millikin.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1127
Message-Id: <20220817053458.698416-1-john@john-millikin.com>
[Fill in correct length for adapters other than ESP. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per investigation on the linked ticket, SunOS issues a SCSI bus reset
to the ESP as part of its boot sequence. If this ESP command doesn't
cause devices to assert sense flag UNIT ATTENTION, SunOS will consider
the CD-ROM device to be non-compliant with Common Command Set (CCS).
In this condition, the SunOS installer's early userspace doesn't set
the installation source location to sr0 and the miniroot copy fails.
Signed-off-by: John Millikin <john@john-millikin.com>
Suggested-by: Bill Paul <noisetube@gmail.com>
Buglink: https://gitlab.com/qemu-project/qemu/-/issues/1127
Message-Id: <20220817053846.699310-1-john@john-millikin.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since PDMA reads/writes are driven by the guest, it is possible that migration
can occur whilst a SCSIRequest is still active. Fortunately active SCSIRequests
are already included in the migration stream and restarted post migration but
this still leaves the reference in ESPState uninitialised.
Implement the SCSIBusInfo .load_request callback to obtain a reference to the
currently active SCSIRequest and use it to recreate ESPState current_req
after migration.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This involves (re)adding a PDMA-specific subsection to hold the reference to the
current PDMA callback.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This prepares for the inclusion of the current PDMA callback in the migration
stream since the callback is referenced by an integer instead of a function
pointer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This function is to be used to execute the current PDMA callback rather than
dereferencing the ESPState pdma_cb function pointer directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This function is to be used to set the current PDMA callback rather than
accessing the ESPState pdma_cb function pointer directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
If a reset command is sent after data has been transferred into the SCSI buffer
ensure that async_len is reset to 0. Otherwise a subsequent TI command assumes
the SCSI buffer contains data to be transferred to the device causing it to
dereference the stale async_buf pointer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/724
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211118100327.29061-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is currently a check in esp_select() to cancel any in-flight SCSI requests
to ensure that issuing multiple select commands without continuing through the
rest of the ESP state machine ignores all but the last SCSI request. This is
also enforced through the addition of assert()s in esp_transfer_data() and
scsi_read_data().
The get_cmd() function does not call esp_select() when TC == 0 which means it is
possible for a fuzzer to trigger these assert()s by sending a select command when
TC == 0 immediately after a valid SCSI CDB has been submitted.
Since esp_select() is only called from get_cmd(), hoist the check to cancel
in-flight SCSI requests from esp_select() into get_cmd() to ensure it is always
called when executing a select command to initiate a new SCSI request.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Closes: https://gitlab.com/qemu-project/qemu/-/issues/662
Closes: https://gitlab.com/qemu-project/qemu/-/issues/663
Message-Id: <20211101183516.8455-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function scsi_bus_new() creates a new SCSI bus; callers can
either pass in a name argument to specify the name of the new bus, or
they can pass in NULL to allow the bus to be given an automatically
generated unique name. Almost all callers want to use the
autogenerated name; the only exception is the virtio-scsi device.
Taking a name argument that should almost always be NULL is an
easy-to-misuse API design -- it encourages callers to think perhaps
they should pass in some standard name like "scsi" or "scsi-bus". We
don't do this anywhere for SCSI, but we do (incorrectly) do it for
other bus types such as i2c.
The function name also implies that it will return a newly allocated
object, when it in fact does in-place allocation. We more commonly
name such functions foo_init(), with foo_new() being the
allocate-and-return variant.
Replace all the scsi_bus_new() callsites with either:
* scsi_bus_init() for the usual case where the caller wants
an autogenerated bus name
* scsi_bus_init_named() for the rare case where the caller
needs to specify the bus name
and document that for the _named() version it's then the caller's
responsibility to think about uniqueness of bus names.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20210923121153.23754-2-peter.maydell@linaro.org
The LUN is selected with an IDENTIFY message, and persists
until the next message out phase. Instead of passing it to
do_busid_cmd, store it in ESPState. Because do_cmd can simply
skip the message out phase if cmdfifo_cdb_offset is zero, it
can now be used for the S without ATN cases as well.
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 4e78f3bf35 "esp: defer command completion interrupt on incoming data
transfers" added a version check for use with VMSTATE_*_TEST macros to allow
migration from older QEMU versions. Unfortunately the version check fails to
work in its current form since if the VMStateDescription version_id is
incremented, the test returns false and so the fields are not included in the
outgoing migration stream.
Change the version check to use >= rather == to ensure that migration works
correctly when the ESPState VMStateDescription has version_id > 5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 4e78f3bf35 ("esp: defer command completion interrupt on incoming data transfers")
Message-Id: <20210613102614.5438-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 799d90d818 "esp: transition to message out phase after SATN and stop
command" added logic to correctly handle extended messages for DMA requests
but not for PDMA requests.
Apply the same logic in esp_do_dma() to do_dma_pdma_cb() so that extended
messages terminated with a PDMA request are accumulated correctly. This allows
the ESP device to respond correctly to the SDTR negotiation initiated by the
NetBSD ESP driver without causing errors and timeouts on boot.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210519100803.10293-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This commit from nearly 10 years ago is now broken due to the improvements
in esp emulation (or perhaps was never correct). It shows up as a bug
in detecting the CDROM drive under MacOS. The error is caused by the
MacOS CDROM driver sending this CDB with an "S without ATN" command and
without DMA:
0x12 0x00 0x00 0x00 0x05 0x00 (INQUIRY)
This is a valid INQUIRY command, however with this logic present the 3rd
byte (0x0) is copied over the 1st byte (0x12) which silently converts the
INQUIRY command to a TEST UNIT READY command before passing it to the
QEMU SCSI layer. Since the TEST UNIT READY command has a zero length
response the MacOS CDROM driver never receives a response and assumes
the CDROM is not present.
The logic was to ignore the IDENTIFY byte and copy the LUN over from
the CDB, which did store the LUN in bits 5-7 of the second byte in
olden times. This however is all obsolete, so just drop the code.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210519100803.10293-5-mark.cave-ayland@ilande.co.uk>
[Tweaked commit message. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After each PDMA write transfer the MacOS CDROM driver waits until the FIFO is empty
(i.e. its contents have been written out to the SCSI bus) by polling the FIFO count
register until it reads 0. This doesn't work with the current PDMA write
implementation which waits until either the FIFO is full or the transfer is complete
before invoking the PDMA callback to process the FIFO contents.
Change the PDMA write transfer logic so that the PDMA callback is invoked after each
PDMA write to transfer the FIFO contents to the target buffer immediately, and hence
avoid getting stuck in the FIFO count register polling loop.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210519100803.10293-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The initial implementation of non-DMA transfers was based upon analysis of traces
from the MacOS toolbox ROM for handling unaligned reads but missed one key
aspect - during a non-DMA transfer from the target, the bus service interrupt
should be raised for every single byte received from the bus and not just at either
the end of the transfer or when the FIFO is full.
Adjust the non-DMA code accordingly so that esp_do_nodma() is called for every byte
received from the target. This also includes special handling for managing the change
from DATA IN to STATUS phase as this needs to occur when the final byte is read out
from the FIFO, and not at the end of the transfer of the last byte into the FIFO.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210519100803.10293-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current implementation only resumes DMA transfers when incoming data is
received from the target device, but this is also required for non-DMA transfers
with the next set of non-DMA changes.
Rather than duplicate the DMA/non-DMA dispatch logic in the initial transfer
section, update the code so that the initial transfer section can just
fallthrough to the main DMA/non-DMA dispatch logic.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210519100803.10293-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When processing a command to select a target and send a CDB, the ESP device
maintains a sequence step register so that if an error occurs the host can
determine which part of the selection/CDB submission sequence failed.
The old Linux 2.6 driver is really pedantic here: it checks the sequence step
register even if a command succeeds and complains loudly on the console if the
sequence step register doesn't match the expected bus phase and interrupt flags.
This reason this mismatch occurs is because the ESP emulation currently doesn't
update the bus phase until the next TI (Transfer Information) command and so the
cleared sequence step register is considered invalid for the stale bus phase.
Normally this isn't an issue as the host only checks the sequence step register
if an error occurs but the old Linux 2.6 driver does this in several places
causing a large stream of "esp0: STEP_ASEL for tgt 0" messages to appear on the
console during the boot process.
Fix this by not clearing the sequence step register when reading the interrupt
register and clearing the DMA status, so the guest sees a valid sequence step
and bus phase combination at the end of the command phase. No other change is
required since the sequence step register is correctly updated throughout the
selection/CDB submission sequence once one of the select commands is issued.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 1b9e48a5bd ("esp: implement non-DMA transfers in PDMA mode")
Message-Id: <20210518212511.21688-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The datasheet sequence tables confirm that when a target selection fails, only
the INTR_DC interrupt flag should be asserted.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: cf47a41e05 ("esp: latch individual bits in ESP_RINTR register")
Message-Id: <20210518212511.21688-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a CDB has been received and is about to be submitted to the SCSI layer
via one of the ESP select commands, ensure that do_cmd is set to zero before
executing the command.
Otherwise a guest executing 2 valid CDBs in quick sequence can invoke the SCSI
.transfer_data callback again before do_cmd is set to zero by the callback
function triggering an assert at the start of esp_transfer_data().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407195801.685-12-mark.cave-ayland@ilande.co.uk>
Instead let the SCSI layer invoke the .cancel callback itself to cancel and
reset the request state.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407195801.685-11-mark.cave-ayland@ilande.co.uk>
If a guest transfers the message out/command phase data using DMA with a TC
that is larger than the cmdfifo size then the cmdfifo overflows triggering
an assert. Limit the size of the transfer to the free space available in
cmdfifo.
Buglink: https://bugs.launchpad.net/qemu/+bug/1919036
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-10-mark.cave-ayland@ilande.co.uk>
If the guest tries to read a CDB using DMA and cmdfifo is not empty then it is
possible to overflow cmdfifo.
Since this can only occur by issuing deliberately incorrect instruction
sequences, ensure that the maximum length of the CDB transferred to cmdfifo is
limited to the available free space within cmdfifo.
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-9-mark.cave-ayland@ilande.co.uk>
If the guest tries to execute a CDB when cmdfifo is not empty before the start
of the message out phase then clearing the message out phase data will cause
cmdfifo to underflow due to cmdfifo_cdb_offset being larger than the amount of
data within.
Since this can only occur by issuing deliberately incorrect instruction
sequences, ensure that the maximum length of esp_fifo_pop_buf() is limited to
the size of the data within cmdfifo.
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-8-mark.cave-ayland@ilande.co.uk>
When about to execute a SCSI command, ensure that cmdfifo is not empty and
current_dev is non-NULL. This can happen if the guest tries to execute a TI
(Transfer Information) command without issuing one of the select commands
first.
Buglink: https://bugs.launchpad.net/qemu/+bug/1910723
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-7-mark.cave-ayland@ilande.co.uk>
The const pointer returned by fifo8_pop_buf() lies directly within the array used
to model the FIFO. Building with address sanitizers enabled shows that if the
caller expects a minimum number of bytes present then if the FIFO is nearly full,
the caller may unexpectedly access past the end of the array.
Introduce esp_fifo_pop_buf() which takes a destination buffer and performs a
memcpy() in it to guarantee that the caller cannot overwrite the FIFO array and
update all callers to use it. Similarly add underflow protection similar to
esp_fifo_push() and esp_fifo_pop() so that instead of triggering an assert()
the operation becomes a no-op.
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210407195801.685-6-mark.cave-ayland@ilande.co.uk>
Each FIFO currently has its own pop functions with the only difference being
the capacity check. The original reason for this was that the fifo8
implementation doesn't have a formal API for retrieving the FIFO capacity,
however there are multiple examples within QEMU where the capacity field is
accessed directly.
Change esp_fifo_pop() to access the FIFO capacity directly and then consolidate
esp_cmdfifo_pop() into esp_fifo_pop().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-5-mark.cave-ayland@ilande.co.uk>
Each FIFO currently has its own push functions with the only difference being
the capacity check. The original reason for this was that the fifo8
implementation doesn't have a formal API for retrieving the FIFO capacity,
however there are multiple examples within QEMU where the capacity field is
accessed directly.
Change esp_fifo_push() to access the FIFO capacity directly and then consolidate
esp_cmdfifo_push() into esp_fifo_push().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-4-mark.cave-ayland@ilande.co.uk>
The code for write_response() has always used the FIFO to store the data for
the status/message in phases, even for DMA transactions. Switch to using a
separate buffer that can be used directly for DMA transactions and restrict
the FIFO use to the non-DMA case.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407195801.685-3-mark.cave-ayland@ilande.co.uk>
After issuing a SCSI command the SCSI layer can call the SCSIBusInfo .cancel
callback which resets both current_req and current_dev to NULL. If any data
is left in the transfer buffer (async_len != 0) then the next TI (Transfer
Information) command will attempt to reference the NULL pointer causing a
segfault.
Buglink: https://bugs.launchpad.net/qemu/+bug/1910723
Buglink: https://bugs.launchpad.net/qemu/+bug/1909247
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210407195801.685-2-mark.cave-ayland@ilande.co.uk>
If QEMU is launched with the -S option then the ESPState mig_version_id property
is left unset due to the ordering of the VMState fields in the VMStateDescription
for sysbusespscsi and pciespscsi. If the VM is migrated and restored in this
stopped state, the version tests in the vmstate_esp VMStateDescription and
esp_post_load() become confused causing the migration to fail.
Fix the ordering problem by moving the setting of mig_version_id to a common
esp_pre_save() function which is invoked first by both sysbusespscsi and
pciespscsi rather than at the point where ESPState is itself serialised into the
migration stream.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922611
Fixes: 0bd005be78 ("esp: add vmstate_esp version to embedded ESPState")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210407124842.32695-1-mark.cave-ayland@ilande.co.uk>
When the MacOS toolbox ROM transfers data from a target device to an unaligned
memory address, the first/last byte of a 16-bit transfer needs to be handled
separately. This means that the first byte is preloaded into the FIFO before
the transfer, or the last byte remains in the FIFO after the transfer.
The result of this is that the PDMA routines must be updated so that the FIFO
is loaded/unloaded if the last 16-bit word is used (rather than the last byte)
and any remaining byte from a FIFO wraparound is handled correctly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-43-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM uses non-DMA TI commands to handle the first/last byte
of an unaligned 16-bit transfer to memory.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-42-mark.cave-ayland@ilande.co.uk>
The bottom 5 bits contain the number of bytes remaining in the FIFO which is
trivial to implement with Fifo8 (the remaining bits are unimplemented and left
as 0 for now).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-41-mark.cave-ayland@ilande.co.uk>
Rename ESP_CMDBUF_SZ to ESP_CMDFIFO_SZ and cmdbuf_cdb_offset to cmdfifo_cdb_offset
to indicate that the command buffer type has changed from an array to a Fifo8.
This also enables us to remove the ESPState field cmdlen since the command length
is now simply the number of elements used in cmdfifo.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-40-mark.cave-ayland@ilande.co.uk>
Rename TI_BUFSZ to ESP_FIFO_SZ since this constant is really describing the size
of the FIFO and is not directly related to the TI size.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-39-mark.cave-ayland@ilande.co.uk>
The SCSI bus should remain in the message out phase after the SATN and stop
command rather than transitioning to the command phase. A new ESPState variable
cmdbuf_cdb_offset is added which stores the offset of the CDB from the start
of cmdbuf when accumulating extended message out phase data.
Currently any extended message out data is discarded in do_cmd() before the CDB
is processed in do_busid_cmd().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-38-mark.cave-ayland@ilande.co.uk>
Some guests use a mixture of DMA and non-DMA transfers in combination with the
SATN and stop command to transfer message out phase and command phase bytes to
the target. Prepare for the next commit by adding a maxlen parameter to
get_cmd() to allow partial transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-37-mark.cave-ayland@ilande.co.uk>
This matches the description in the datasheet and is required as support for
non-DMA transfers is added.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-36-mark.cave-ayland@ilande.co.uk>
Commit ea84a44250 "scsi: esp: Defer command completion until previous interrupts
have been handled" provided a mechanism to delay the command completion interrupt
until ESP_RINTR is read after the command has completed.
With the previous fixes for latching the ESP_RINTR bits and deferring the setting
of the command completion interrupt for incoming data to the SCSI callback, this
workaround is no longer required and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-35-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM issues a command to the ESP controller as part of its
"FAST" SCSI routines and then proceeds to read the incoming data soon after
receiving the command completion interrupt.
Unfortunately due to SCSI block transfers being asynchronous the incoming data
may not yet be present causing an underflow error. Resolve this by waiting for
the SCSI subsystem transfer_data callback before raising the command completion
interrupt.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-34-mark.cave-ayland@ilande.co.uk>
Currently the ESP_RINTR register is set to a specific value as required within
the ESP state machine. In order to implement the upcoming deferred interrupt
functionality it is necessary to set individual bits within ESP_RINTR so that
a deferred interrupt will not overwrite the value of any other interrupt bits.
This also requires fixing up a few locations where the ESP_RINTR and ESP_RSEQ
registers are set/reset unexpectedly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-33-mark.cave-ayland@ilande.co.uk>
At this point it is now possible to properly implement the FIFO flush command
without causing guest errors.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-32-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM performs 4 byte reads/writes when transferring data to
and from the target. Since the SCSI bus is 16-bits wide, use the memory API
to split a 4 byte access into 2 x 2 byte accesses.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-31-mark.cave-ayland@ilande.co.uk>
Now that all data is transferred via the FIFO (ti_buf) there is no need to track
the source buffer being used for the data transfer. This also eliminates the
need for a separate subsection for PDMA state migration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-30-mark.cave-ayland@ilande.co.uk>
PDMA as implemented on the Quadra 800 uses DREQ to load data into the FIFO
up to a maximum of 16 bytes at a time. The MacOS toolbox ROM requires this
because it mixes FIFO and PDMA transfers whilst checking the FIFO status
and counter registers to ensure success.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-29-mark.cave-ayland@ilande.co.uk>
Currently the target selection for PDMA is done after the SCSI command has been
delivered which is not correct. Perform target selection as part of the initial
get_cmd() call when the command is submitted: if no target is present, don't
raise DRQ.
If the target is present then switch to the command phase since the MacOS toolbox
ROM checks for this before attempting to submit the SCSI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-28-mark.cave-ayland@ilande.co.uk>
This better describes the purpose of the function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-27-mark.cave-ayland@ilande.co.uk>
The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Here the updates to async_len and ti_size are moved into the corresponding
esp_pdma_read()/esp_pdma_write() function to eliminate the reference to
pdma_cur in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-23-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf and buflen
parameters from get_cmd() since these always reference cmdbuf and ESP_CMDBUF_SZ
respectively.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-21-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf parameter
from do_cmd() since this always points to cmdbuf.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-20-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
This is the first step in removing get_pdma_buf() from esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-17-mark.cave-ayland@ilande.co.uk>
The limiting of DMA transfers to the maximum size of the available data is already
handled by esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-15-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
This function simplifies reading the STC register value without having to manually
shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-11-mark.cave-ayland@ilande.co.uk>
These functions simplify reading and writing the TC register value without having to
manually shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-10-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
Move the trace event to the end of the function so that it correctly reports
the returned value if it doesn't come directly from the rregs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-7-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fixes: 74d71ea16b
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200218094402.26625-8-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There is no DMA in Quadra 800, so the CPU reads/writes the data from the
PDMA register (offset 0x100, ESP_PDMA in hw/m68k/q800.c) and copies them
to/from the memory.
There is a nice assembly loop in the kernel to do that, see
linux/drivers/scsi/mac_esp.c:MAC_ESP_PDMA_LOOP().
The start of the transfer is triggered by the DREQ interrupt (see linux
mac_esp_send_pdma_cmd()), the CPU polls on the IRQ flag to start the
transfer after a SCSI command has been sent (in Quadra 800 it goes
through the VIA2, the via2-irq line and the vIFR register)
The Macintosh hardware includes hardware handshaking to prevent the CPU
from reading invalid data or writing data faster than the peripheral
device can accept it.
This is the "blind mode", and from the doc:
"Approximate maximum SCSI transfer rates within a blocks are 1.4 MB per
second for blind transfers in the Macintosh II"
Some references can be found in:
Apple Macintosh Family Hardware Reference, ISBN 0-201-19255-1
Guide to the Macintosh Family Hardware, ISBN-0-201-52405-8
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-4-laurent@vivier.eu>
This will be needed to implement pseudo-DMA
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-3-laurent@vivier.eu>
To prepare following patches move do_cmd and DMA special case
from handle_ti() to esp_do_dma().
This part of the code must be only executed with real DMA, not with
pseudo-DMA. And PDMA is detected in esp_do_dma(), so move this part
of the code in esp_do_dma(). We keep the code in handle_ti_cmd()
in the case no DMA is done.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20191026164546.30020-2-laurent@vivier.eu>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
The guest OS reads RSTAT, RSEQ, and RINTR, and expects those registers
to reflect a consistent state. However, it is possible that the registers
can change after RSTAT was read, but before RINTR is read, when
esp_command_complete() is called.
Guest OS qemu
-------- ----
[handle interrupt]
Read RSTAT
esp_command_complete()
RSTAT = STAT_ST
esp_dma_done()
RSTAT |= STAT_TC
RSEQ = 0
RINTR = INTR_BS
Read RSEQ
Read RINTR RINTR = 0
RSTAT &= ~STAT_TC
RSEQ = SEQ_CD
The guest OS would then try to handle INTR_BS combined with an old
value of RSTAT. This sometimes resulted in lost events, spurious
interrupts, guest OS confusion, and stalled SCSI operations.
A typical guest error log (observed with various versions of Linux)
looks as follows.
scsi host1: Spurious irq, sreg=13.
...
scsi host1: Aborting command [84531f10:2a]
scsi host1: Current command [f882eea8:35]
scsi host1: Queued command [84531f10:2a]
scsi host1: Active command [f882eea8:35]
scsi host1: Dumping command log
scsi host1: ent[15] CMD val[44] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[00] event[0c]
scsi host1: ent[16] CMD val[01] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[17] CMD val[43] sreg[90] seqreg[00] sreg2[00] ireg[20] ss[02] event[0c]
scsi host1: ent[18] EVENT val[0d] sreg[92] seqreg[04] sreg2[00] ireg[18] ss[00] event[0c]
...
Defer handling command completion until previous interrupts have been
handled to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove the legacy esp_init() function now that there are no more remaining
users.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20180613094727.11326-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
As part of plumbing MemTxAttrs down to the IOMMU translate method,
add MemTxAttrs as an argument to the MemoryRegion valid.accepts
callback. We'll need this for subpage_accepts().
We could take the approach we used with the read and write
callbacks and add new a new _with_attrs version, but since there
are so few implementations of the accepts hook we just change
them all.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180521140402.23318-9-peter.maydell@linaro.org
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
This enables them to be used outside of esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
SunOS defines ESP (x86 register) in <sys/regset.h> as 7.
This fixes build on SmartOS (Joyent).
Signed-off-by: Kamil Rytarowski <n54@gmx.com>
Message-Id: <20170909142116.26816-1-n54@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The logic to create frontends for -drive if=scsi is in SCSI HBAs. For
all other interface types, it's in machine initialization code.
A few machine types create the SCSI HBAs necessary for that. That's
also not done for other interface types.
I'm going to deprecate these SCSI eccentricities. In preparation for
that, create the frontends in main() instead of the SCSI HBAs, by
calling new function scsi_legacy_handle_cmdline() there.
Note that not all SCSI HBAs create frontends. Take care not to change
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487161136-9018-2-git-send-email-armbru@redhat.com>
Acked-By: Paolo Bonzini <pbonzini@redhat.com>
This fixes SCSI adapter self-tests done in MIPS Jazz emulation,
broken since ff589551c8.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1479508397-8443-1-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 926cde5 ("scsi: esp: make cmdbuf big enough for maximum CDB size",
2016-06-16) changed the size of a migrated field. Split it in two
parts, and only migrate the second part in a new vmstate version.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While doing DMA read into ESP command buffer 's->cmdbuf', it could
write past the 's->cmdbuf' area, if it was transferring more than 16
bytes. Increase the command buffer size to 32, which is maximum when
's->do_cmd' is set, and add a check on 'len' to avoid OOB access.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid duplicated code between esp_do_dma and handle_ti. esp_do_dma
has the same code that handle_ti contains after the call to esp_do_dma;
but the code in handle_ti is never reached because it is in an "else if".
Remove the else and also the pointless return.
esp_do_dma also has a partially dead assignment of the to_device
variable. Sink it to the point where it's actually used.
Finally, assert that the other caller of esp_do_dma (esp_transfer_data)
only transfers data and not a command. This is true because get_cmd
cancels the old request synchronously before its caller handle_satn_stop
sets do_cmd to 1.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer.
Routine get_cmd() in non-DMA mode, uses 'ti_size' to read scsi
command into a buffer. Add check to validate command length against
buffer size to avoid any overrun.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1464717207-7549-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with internal 16-byte
FIFO buffers. One is used to handle commands and other is for
information transfer. Three control variables 'ti_rptr',
'ti_wptr' and 'ti_size' are used to control r/w access to the
information transfer buffer ti_buf[TI_BUFSZ=16]. In that,
'ti_rptr' is used as read index, where read occurs.
'ti_wptr' is a write index, where write would occur.
'ti_size' indicates total bytes to be read from the buffer.
While reading/writing to this buffer, index could exceed its
size. Add check to avoid OOB r/w access.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1465230883-22303-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer.
Routine get_cmd() uses DMA to read scsi commands into this buffer.
Add check to validate DMA length against buffer size to avoid any
overrun.
Fixes CVE-2016-4441.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Cc: qemu-stable@nongnu.org
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1463654371-11169-3-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 53C9X Fast SCSI Controller(FSC) comes with an internal 16-byte
FIFO buffer. It is used to handle command and data transfer. While
writing to this command buffer 's->cmdbuf[TI_BUFSZ=16]', a check
was missing to validate input length. Add check to avoid OOB write
access.
Fixes CVE-2016-4439.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Cc: qemu-stable@nongnu.org
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1463654371-11169-2-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-24-git-send-email-peter.maydell@linaro.org
After a reset ESP_TCHI should contain the unique ID
of the chip. This value will be overwritten with the
current tranfer count if the transfer count has
previously been set.
So we should always return the chip id if ESP_TCHI
has never been written to.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
To be passed to qbus_create_inplace().
Use DEVICE() casts instead of direct parent field access.
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Let scsi_bus_legacy_add_drive() and scsi_bus_legacy_handle_cmdline()
return an Error**. Prepare qdev initfns for QOM realize error model.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant and avoid DO_UPCAST().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This adds the possibility to create a scsi-bus with a specified name.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1367330931-12994-4-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
