ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35)
and the base address of dram is "0x4 00000000" which
is 64bits address.
The AST2700 support the maximum DRAM size is 8 GB.
The DRAM physical address range is from "0x4_0000_0000" to
"0x5_FFFF_FFFF".
The DRAM offset range is from "0x0_0000_0000" to
"0x1_FFFF_FFFF" and it is enough to use bits [33:0]
saving the dram offset.
Therefore, save the high part physical address bit[1:0]
of Tx/Rx buffer address as dma_dram_offset bit[33:32].
It does not need to decrease the dram physical
high part address for DMA operation.
(high part physical address bit[7:0] – 4)
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35)
and the base address of dram is "0x4 00000000" which
is 64bits address.
It has "Master DMA Mode Tx Buffer Base Address[39:32](0x60)"
and "Master DMA Mode Rx Buffer Base Address[39:32](0x64)"
registers to save the high part physical address of Tx/Rx
buffer address for master mode.
It has "Slave DMA Mode Tx Buffer Base Address[39:32](0x68)" and
"Slave DMA Mode Rx Buffer Base Address[39:32](0x6C)" registers
to save the high part physical address of Tx/Rx buffer address
for slave mode.
Ex: Tx buffer address for master mode [39:0]
The "Master DMA Mode Tx Buffer Base Address[39:32](0x60)"
bits [7:0] which corresponds the bits [39:32] of the 64 bits address of
the Tx buffer address.
The "Master DMA Mode Tx Buffer Base Address(0x30)" bits [31:0]
which corresponds the bits [31:0] of the 64 bits address
of the Tx buffer address.
Introduce a new has_dma64 class attribute and new registers for the
new mode to support DMA 64 bits dram address.
Update new mode register number to 28.
The aspeed_i2c_bus_vmstate is changed again and
version is not increased because it was done earlier in the same series.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Introduce a new ast2700 class to support AST2700.
The I2C bus register memory regions and
I2C bus pool buffer memory regions are discontinuous
and they do not back compatible AST2600.
Add a new ast2700 i2c class init function to match the
address of I2C bus register and pool buffer from the datasheet.
An I2C controller registers owns 8KB address space.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
The "Current DMA Operating Address Status(0x50)" register of
I2C new mode has been removed in AST2700.
This register is used for debugging and it is a read only register.
To support AST2700 DMA mode, introduce a new
dma_dram_offset class attribute in AspeedI2Cbus to save the
current DMA operating address.
ASPEED AST2700 SOC is a 64 bits quad core CPUs (Cortex-a35)
And the base address of dram is "0x4 00000000" which
is 64bits address.
Set the dma_dram_offset data type to uint64_t for
64 bits dram address DMA support.
Both "DMA Mode Buffer Address Register(I2CD24 old mode)" and
"DMA Operating Address Status (I2CC50 new mode)" are used for showing the
low part dram offset bits [31:0], so change to read/write both register bits [31:0] in
bus register read/write functions.
The aspeed_i2c_bus_vmstate is changed again and version is not increased
because it was done earlier in the same series.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
It only support continuous pool buffer memory region for all I2C bus.
However, the pool buffer address of all I2c bus are discontinuous
for AST2700.
Ex: the pool buffer address of I2C bus for ast2700 as following.
0x1A0 - 0x1BF: Device 0 buffer
0x2A0 - 0x2BF: Device 1 buffer
0x3A0 - 0x3BF: Device 2 buffer
0x4A0 - 0x4BF: Device 3 buffer
0x5A0 - 0x5BF: Device 4 buffer
0x6A0 - 0x6BF: Device 5 buffer
0x7A0 - 0x7BF: Device 6 buffer
0x8A0 - 0x8BF: Device 7 buffer
0x9A0 - 0x9BF: Device 8 buffer
0xAA0 - 0xABF: Device 9 buffer
0xBA0 - 0xBBF: Device 10 buffer
0xCA0 - 0xCBF: Device 11 buffer
0xDA0 - 0xDBF: Device 12 buffer
0xEA0 - 0xEBF: Device 13 buffer
0xFA0 – 0xFBF: Device 14 buffer
0x10A0 – 0x10BF: Device 15 buffer
Introduce a new class attribute to make user set each I2C bus
pool buffer gap size. Update formula to create all I2C bus
pool buffer memory regions.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
According to the datasheet of ASPEED SOCs,
each I2C bus has their own pool buffer since AST2500.
Only AST2400 utilized a pool buffer share to all I2C bus.
Besides, using a share pool buffer only support
pool buffer memory regions are continuous for all I2C bus.
To make this model more readable and support discontinuous
bus pool buffer memory regions, changes to introduce
a new bus pool buffer attribute in AspeedI2Cbus and
new memops. So, it does not need to calculate
the pool buffer offset for different I2C bus.
Introduce a new has_share_pool class attribute in AspeedI2CClass and
use it to create either a share pool buffer or bus pool buffers
in aspeed_i2c_realize. Update each pull buffer size to 0x10 for AST2500
and 0x20 for AST2600 and AST1030.
Incrementing the version of aspeed_i2c_bus_vmstate to 6.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
It only support continuous register memory region for all I2C bus.
However, the register address of all I2c bus are discontinuous
for AST2700.
Ex: the register address of I2C bus for ast2700 as following.
0x100 - 0x17F: Device 0
0x200 - 0x27F: Device 1
0x300 - 0x37F: Device 2
0x400 - 0x47F: Device 3
0x500 - 0x57F: Device 4
0x600 - 0x67F: Device 5
0x700 - 0x77F: Device 6
0x800 - 0x87F: Device 7
0x900 - 0x97F: Device 8
0xA00 - 0xA7F: Device 9
0xB00 - 0xB7F: Device 10
0xC00 - 0xC7F: Device 11
0xD00 - 0xD7F: Device 12
0xE00 - 0xE7F: Device 13
0xF00 – 0xF7F: Device 14
0x1000 – 0x107F: Device 15
Introduce a new class attribute to make user set each I2C bus gap size.
Update formula to create all I2C bus register memory regions.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Use device_class_set_legacy_reset() instead of opencoding an
assignment to DeviceClass::reset. This change was produced
with:
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/device-reset.cocci \
--keep-comments --smpl-spacing --in-place --dir hw
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240830145812.1967042-8-peter.maydell@linaro.org
The last register of this device is at offset 0x14 occupying 8 bits so
to cover it the mmio region needs to be 0x15 bytes long. Also correct
the name of the field storing this register value to match the
register name.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Fixes: 7abb479c7a ("PPC: E500: Add FSL I2C controller")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240721225506.B32704E6039@zero.eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
According to the datasheet of ASPEED SOCs,
each I2C bus has their own pool buffer since AST2500.
Only AST2400 utilized a pool buffer share to all I2C bus.
And firmware required to set the offset of pool buffer
by writing "Function Control Register(I2CD 00)"
To make this model more readable, will change to introduce
a new bus pool buffer attribute in AspeedI2Cbus.
So, it does not need to calculate the pool buffer offset
for different I2C bus.
This patch rename the I2C class pool attribute to share_pool.
It make user more understand share pool and bus pool
are different.
Incrementing the version of aspeed_i2c_vmstate to 3.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
According to the datasheet of ASPEED SOCs,
an I2C controller owns 8KB of register space for AST2700,
owns 4KB of register space for AST2600, AST2500 and AST2400,
and owns 64KB of register space for AST1030.
It set the memory region size 4KB by default and it does not compatible
register space for AST2700.
Introduce a new class attribute to set the I2C controller memory size
for different ASPEED SOCs.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.
Commit created with
for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done
and no manual edits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org
Rather than directly calling the device's implementation of its 'hold'
reset phase, call device_cold_reset(). This means we don't have to
adjust this callsite when we add another argument to the function
signature for the hold and exit reset methods.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-3-peter.maydell@linaro.org
A few deficiencies in the current device model need to be noted.
1. FIFOs are not used. All sends and receives are done directly.
2. Repeated starts are not emulated. Repeated starts can be triggered in real
hardware by sending a new read transfer request in the window time between
transfer active set of write transfer request and done bit set of the same.
Signed-off-by: Rayhan Faizel <rayhan.faizel@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240224191038.2409945-2-rayhan.faizel@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current logging doesn't tell us which specific smbus device is an
error state.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240202204847.2062798-3-komlodi@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The linux pmbus driver scans all possible pages and does not reset the
current page after the scan, making all future page reads fail as out of range
on devices with a single page.
This change resets out of range pages immediately on write.
Also added a qtest for simultaneous writes to all pages.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-8-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The probing process of the generic pmbus driver generates
faults to determine if functions are available. These faults
were not always cleared resulting in probe failures.
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-7-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
VCAP is a register for devices with energy storage capacitors.
Reviewed-by: Benjamin Streb <bstreb@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-4-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PMBus devices may integrate fans whose operation is configurable
over PMBus. This commit allows the driver to read and write the
fan control registers but does not model the operation of fans.
Reviewed-by: Stephen Longfield <slongfield@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-3-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PMBus devices can send and receive variable length data using the
block read and write format, with the first byte in the payload
denoting the length.
This is mostly used for strings and on-device logs. Devices can
respond to a block read with an empty string.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-1-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
* linux-user/elfload: Add missing arm64 hwcap values
* stellaris-gamepad: Convert to qdev
* docs/specs: Convert various txt docs to rST
* MAINTAINERS: Make sure that gicv3_internal.h is covered, too
* hw/arm/pxa2xx_gpio: Pass CPU using QOM link property
* hw/watchdog/wdt_imx2: Trace MMIO access and timer activity
* hw/misc/imx7_snvs: Trace MMIO access
* hw/misc/imx6_ccm: Convert DPRINTF to trace events
* hw/i2c/pm_smbus: Convert DPRINTF to trace events
* target/arm: Enable FEAT_MOPS insns in user-mode emulation
* linux-user: Report AArch64 hwcap2 fields above bit 31
* target/arm: Make FEAT_MOPS SET* insns handle Xs == XZR correctly
* target/arm: Fix SVE STR increment
* hw/char/stm32f2xx_usart: implement TX interrupts
* target/arm: Correctly propagate stage 1 BTI guarded bit in a two-stage walk
* xlnx-versal-virt: Add AMD/Xilinx TRNG device
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmVD3hEZHHBldGVyLm1h
eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3kuRD/4mLL2DB+yvQJrzSvUlrjfi
/orPDrY9xEQ7ln2YpNqc2BZ4wAgh947yk/ae5+lyACQcBhCPiwMyVK1bBscNxkgA
8YPmuugNem/64+IHiKkz6aroqjvC83dUzJ9R5O9ctV70mgrX32YnhXNkkYVI81Ar
bEwBznyYeCiy8ZafVxc2m70fiBOlurb6htYYdt7VHsgB0ozK/80UmuFI6exOKt1r
oVyYouMaidNV/AoqZBGSKT2UFvFmI57PWN0YQD8CMECLsB/mBE9TEzSvLRdlOB4G
qI5hgEJks61qDL6+YMJ+hskxW+D3g3I1WjuyqhKfiAzcKmmTAp1NsiiDtva8yBzX
lDUXc6bPomalrKo1SPsooJv9r4uE3hCayDOlR+qM38DL4j2soSd3QIP7dCzERbZx
snrD+ZTtgXtomUN8ojbnOK+kClEfURZ+wALbUEXwAh1sBwrKBxaD4ss4lA2esq10
HJPjBJzAWoSmK2DY6GWt2xIa+GvQwdPnxMpHbp3yAddGP7i/lHM0x60q5YpjHV++
DHaZmLBA7L9wcvT1VrwmieJaB+ADcSfkzBz2KznC4usdEY8BiJhjdRAzkqdGZWV5
HKEg8QwMYHg4QRUoZxW/XdtVzdqcjO5pTSUr3HUE+85sum2e9Yee6rybg1W/EWYv
7SnVkD5zG1BU268/p5k6UA==
=OgfH
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20231102' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* linux-user/elfload: Add missing arm64 hwcap values
* stellaris-gamepad: Convert to qdev
* docs/specs: Convert various txt docs to rST
* MAINTAINERS: Make sure that gicv3_internal.h is covered, too
* hw/arm/pxa2xx_gpio: Pass CPU using QOM link property
* hw/watchdog/wdt_imx2: Trace MMIO access and timer activity
* hw/misc/imx7_snvs: Trace MMIO access
* hw/misc/imx6_ccm: Convert DPRINTF to trace events
* hw/i2c/pm_smbus: Convert DPRINTF to trace events
* target/arm: Enable FEAT_MOPS insns in user-mode emulation
* linux-user: Report AArch64 hwcap2 fields above bit 31
* target/arm: Make FEAT_MOPS SET* insns handle Xs == XZR correctly
* target/arm: Fix SVE STR increment
* hw/char/stm32f2xx_usart: implement TX interrupts
* target/arm: Correctly propagate stage 1 BTI guarded bit in a two-stage walk
* xlnx-versal-virt: Add AMD/Xilinx TRNG device
* tag 'pull-target-arm-20231102' of https://git.linaro.org/people/pmaydell/qemu-arm: (33 commits)
tests/qtest: Introduce tests for AMD/Xilinx Versal TRNG device
hw/arm: xlnx-versal-virt: Add AMD/Xilinx TRNG device
hw/misc: Introduce AMD/Xilix Versal TRNG device
target/arm: Correctly propagate stage 1 BTI guarded bit in a two-stage walk
hw/char/stm32f2xx_usart: Add more definitions for CR1 register
hw/char/stm32f2xx_usart: Update IRQ when DR is written
hw/char/stm32f2xx_usart: Extract common IRQ update code to update_irq()
target/arm: Fix SVE STR increment
target/arm: Make FEAT_MOPS SET* insns handle Xs == XZR correctly
linux-user: Report AArch64 hwcap2 fields above bit 31
target/arm: Enable FEAT_MOPS insns in user-mode emulation
hw/i2c/pm_smbus: Convert DPRINTF to trace events
hw/misc/imx6_ccm: Convert DPRINTF to trace events
hw/misc/imx7_snvs: Trace MMIO access
hw/watchdog/wdt_imx2: Trace timer activity
hw/watchdog/wdt_imx2: Trace MMIO access
hw/arm/pxa2xx_gpio: Pass CPU using QOM link property
MAINTAINERS: Make sure that gicv3_internal.h is covered, too
docs/specs/vmgenid: Convert to rST
docs/specs/vmcoreinfo: Convert to rST
...
Conflicts:
hw/input/stellaris_input.c
The qdev conversion in this pull request ("stellaris-gamepad: Convert
to qdev") eliminates the vmstate_register() call that was converted to
vmstate_register_any() in the conflicting migration pull request.
vmstate_register_any() is no longer necessary now that this device has
been converted to qdev, so take this pull request's version of
stellaris_gamepad.c over the previous pull request's
stellaris_input.c (the file was renamed).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Let the trace messages slightly deviate from the function names
("smb" -> "smbus") being traced in order to avoid conflights with the SMB
protocol.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20231028122415.14869-6-shentey@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This are the easiest cases, where we were already using
VMSTATE_INSTANCE_ID_ANY.
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231020090731.28701-3-quintela@redhat.com>
Remove superfluous local 'data' variable and use the one define at the
top of the routine. This fixes :
../hw/i2c/aspeed_i2c.c: In function ‘aspeed_i2c_bus_recv’:
../hw/i2c/aspeed_i2c.c:315:17: warning: declaration of ‘data’ shadows a previous local [-Wshadow=compatible-local]
315 | uint8_t data;
| ^~~~
../hw/i2c/aspeed_i2c.c:288:13: note: shadowed declaration is here
288 | uint8_t data;
| ^~~~
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230922155924.1172019-2-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
-----BEGIN PGP SIGNATURE-----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=ymmX
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu into staging
aspeed queue:
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmTxsaQACgkQUaNDx8/7
# 7KGXmg//XJNisscl/VWSBaGmH5MbQUAg/QCRalXx1V/lJ8rhE/JqwnWKuoPFd4EN
# iDlh3ufpzxPhHFc9boechuM5ytlrJxpLJoCIJ4sw/4qnO3Dy3Q6BCy1t8Ma62D1u
# oE7cAMHsriJ1uTJNHUTFo72VapTaH2XwFN9lFDuQW45d+WWAXtVJsqvRgFETNmw6
# YYnTTpH2gLTZZFEgOixhWpGLh4Ibc/l8U1VzL0ctQmC11xng0bqk3PAqU9NGzcM5
# MJmEGAxg43CnFu9NJI1nMqC/coi/8PFtrM7HprSwE3H8Jkwncs4ePVT+kZQC+VNQ
# 7EaVkksfEGHlN8XP5+eQDrQ5yT6ve+fbHTLQhwULfeyt0GlQ8h1yewvHCDWo/zw3
# XI1ZyOcNZ2yiaenSUrTPzu0LiqZEJQnzRjPCpgTi1fU08ryEMEaPtr176YDLCguQ
# cpRj4QSZHCrGl/Eo9NlkFP/2rQDKTvCcedKPkYLQtsurSiH/36Oj9YvZycNtZ574
# ortKAtru4YV/rglNX4L8JDhdI+nqvy1liifpJsiS/2KBZDpVFaP8PzGIV40HNy3G
# 8/LVTnaggZaScF3ftHhkg84uQumELS9l2dhsNCL9HqdlrNXLQrVAIR6iuQlpOKBa
# 5S/6h7ZXGOb1qNVQjYp4HCrB7X1KIJYksZ3GdUREf8ot5Ds1FhE=
# =ymmX
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Sep 2023 05:40:52 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu: (26 commits)
hw/sd: Introduce a "sd-card" SPI variant model
hw/sd: Add sd_cmd_SET_BLOCK_COUNT() handler
hw/sd: Add sd_cmd_SEND_TUNING_BLOCK() handler
hw/sd: Add sd_cmd_SEND_RELATIVE_ADDR() handler
hw/sd: Add sd_cmd_ALL_SEND_CID() handler
hw/sd: Add sd_cmd_SEND_OP_CMD() handler
hw/sd: Add sd_cmd_GO_IDLE_STATE() handler
hw/sd: Add sd_cmd_unimplemented() handler
hw/sd: Add sd_cmd_illegal() handler
hw/sd: Introduce sd_cmd_handler type
hw/sd: Move proto_name to SDProto structure
hw/sd: When card is in wrong state, log which spec version is used
hw/sd: When card is in wrong state, log which state it is
hw/sd/sdcard: Return ILLEGAL for CMD19/CMD23 prior SD spec v3.01
aspeed: Get the BlockBackend of FMC0 from the flash device
m25p80: Introduce an helper to retrieve the BlockBackend of a device
aspeed: Create flash devices only when defaults are enabled
hw/ssi: Check for duplicate CS indexes
aspeed/smc: Wire CS lines at reset
hw/ssi: Introduce a ssi_get_cs() helper
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Added support for the buffer organization option in pool buffer control
register.when set to 1,The buffer is split into two parts: Lower 16 bytes
for Tx and higher 16 bytes for Rx.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to the ast2600 datasheet and the linux aspeed i2c driver,
the TXBUF transmission start position should be TXBUF[0] instead
of TXBUF[1],so the arg pool_start is useless,and the address is not
included in TXBUF.So even if Tx Count equals zero,there is at least
1 byte data needs to be transmitted,and M_TX_CMD should not be cleared
at this condition.The driver url is:
https://github.com/AspeedTech-BMC/linux/blob/aspeed-master-v5.15/drivers/i2c/busses/i2c-ast2600.c
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 6054fc73e8 ("aspeed/i2c: Add support for pool buffer transfers")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
QOM object instance should not modify its class state (because
all other objects instanciated from this class get affected).
Instead of modifying the PMBusDeviceClass 'device_num_pages' field
the first time a instance is initialized (in pmbus_pages_alloc),
introduce a new pmbus_pages_num() helper which returns the page
number from the class without modifying the class state.
The code logic become slighly simplified.
Inspired-by: Bernhard Beschow <shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230523064408.57941-4-philmd@linaro.org>
The clock and data values were logged swapped. Correct the trace event
text to match what is logged. Also fix a typo in a comment nearby.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This allows the devices to be more readily found and specified.
Without setting the name field, they can only be found by device type
name, which doesn't let you specify the second of the same device type
behind a bus.
Tested: Verified that by default the device was findable with the name
'pca954x[77]', for an instance attached at that address.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20230322172136.48010-1-venture@google.com>
[PMD: Fix typo in property name]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In commit 8461bfdca9 we added the TYPE_AW_I2C_SUN6I, which is a
minor variant of the TYPE_AW_I2C device. However, we didn't quite
get the class hierarchy right. We made the new TYPE_AW_I2C_SUN6I a
subclass of TYPE_SYS_BUS_DEVICE, which means that you can't validly
use a pointer to this object via the AW_I2C() cast macro, which
insists on having something that is an instance of TYPE_AW_I2C or
some subclass of that type.
This only causes a problem if QOM cast macro debugging is enabled;
that is supposed to be on by default, but a mistake in the meson
conversion in commit c55cf6ab03 meant that it ended up disabled by
default, and we didn't catch this bug.
Fix the problem by arranging the classes in the same way we do for
TYPE_PL011 and TYPE_PL011_LUMINARY in hw/char/pl011.c -- make the
variant class be a subclass of the "normal" version of the device.
This was reported in
https://gitlab.com/qemu-project/qemu/-/issues/1586 but this fix alone
isn't sufficient, as there is a separate cast-related issue in the
CXL code in pci_expander_bridge.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Devices models calling pmbus_send_string can't be relied upon to
send a non-zero pointer. This logs an error and doesn't segfault.
Reviewed-by: Patrick Venture <venture@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230322175513.1550412-5-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
It is not given that the current master will release the bus after a
transfer ends. Only schedule a pending master if the bus is idle.
Fixes: 37fa5ca426 ("hw/i2c: support multiple masters")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20221116084312.35808-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
ICH9 is a south bridge which doesn't necessarily depend on x86, so move
it into the southbridge folder, analoguous to PIIX.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-13-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
ich9_smb_init() is a legacy init function, so modernize the code.
Note that the smb_io_base parameter was unused.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This is a preparation for the next commit to make it cleaner.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230213173033.98762-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
This commit was created with scripts/clean-includes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20230202133830.2152150-19-armbru@redhat.com>
Frees isa-bus.c from implicit ACPI dependency.
While at it, resolve open coding of qbus_build_aml() in piix3 and ich9.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230121151941.24120-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ARM_SBCON_I2C() macro and ArmSbconI2CState typedef are
already declared via the QOM DECLARE_INSTANCE_CHECKER()
macro in "hw/i2c/arm_sbcon_i2c.h". Drop the VERSATILE_I2C
declarations from versatile_i2c.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
