- 'flat' mode: disk image size must be multiple of sector size.
- 'concat' mode: each disk image size and lseek() offset must be multiple of
sector size.
- 'sparse' mode: page size and lseek() offset must be multiple of sector size.
- TODO: 'growing', 'undoable' and 'volatile' mode: redolog_t class is still
based on 512-byte blocks.
- TODO: 'vbox', 'vmware3', 'vmware4', 'vpc' and 'vvfat' mode have a builtin
geometry. If other sector sizes are supported, it should be handled correctly.
- harddrv code now reports current sector size, but still panics for now.
- TODO: harrdrv and USB disk code, bximage, BIOS.
This code is based on the initial patch by Ben Lunt with some modifications:
using enum parameter, extra parser handler and cdrom handling not necessary,
TODO: hdimage and bximage code, harddrv and USB disk emulation, BIOS.
- Fixed PCI BAR initialization (now using memset()).
- Fixed reset failure (set all PAM memory types to ROM).
- Added stub for the AGP aperture (register BAR #0, handle APSIZE and read
GART entry in read/write handlers).
- Added some more PCI register defaults and write masks.
- Fixed a warning in the ES1370 code.
- Voodoo Banshee: set up PCI subsystem ID depending on bus and model.
- Volatile BIOS write support must also be present in ISA BIOS memory.
- Added new PCI chipset choice for the i440BX AGPset. Some basic work is done,
but AGP support is not present yet.
- Added new class for the "virtual" PCI-to-PCI bridge that should manage the
secondary bus (AGP). Since this device must appear with device number #1 at
the primary bus, it was required to change the PCI device numbers for the
i440BX case. Moved the PIIX4 module to device number #7. The presence of the
PCI base address regions now depends on the header type as expected.
- Since the Bochs BIOS cannot handle the modified PCI device layout, all tests
continued with an external BIOS designed for this chipset (GA-6BA_F1.bin).
This BIOS requires additional changes in some devices.
- ACPI: Return value 0 for some status registers and the GPI registers.
- CMOS: Since the PIIX4 supports a 256 byte CMOS RAM, prepared support for it
and enable it in case a 256 byte CMOS image is used.
- PCI: The device numbers for 4 slots starting at #8. The 5th slot could be
used for AGP when available.
Using a temporary subsystem ID, since I haven't found a VGABIOS ROM image for
the PCI version and Bochs doesn't support AGP yet. After modifying Voodoo3.inf
the driver could be installed successfully in Win95/98 and the Voodoo3 works as
expected (same issues as the Banshee model).
Removed BX_ERROR message about setting undocumented srcXY register bits. They
seem to have no effect on the emulation and could be ignored.
- Screen-to-screen blt: added support for expanding monochrome source data.
- Fixed calculation of the pitch for packed source data.
- Fixed repeated execution of some commands in non-immediate mode.
- PCI devices: fixed and improved BX_INFO / BX_DEBUG messages.
- Added INT pin init to method init_pci_conf().
- Moved readonly register handling to the common PCI write handler.
- Moved IRQ line reporting to the common PCI write handler.
- Added new structure bx_pci_bar_t that contains all parameters related to the
PCI BARs (type, size, address and r/w handlers).
- Added new methods init_bar_io() and init_bar_mem() to set up the new structure
in the pci device init code.
- Added new method pci_write_handler_common() to handle writes to the normal
BARs and the ROM BAR. Writes to other registers are forwarded to the device
specific PCI write handlers. Removed BAR and ROM BAR handling from the
specific code.
- Added new method pci_bar_change_notify() to execute specific code after BAR
update (vga, ne2k).
- Moved normal BAR handling to method after_restore_pci_state().
- Store pointer to PCI device name in bx_pci_device_c and use it for i/o setup.
- Added support for stippled lines.
- Fixed return values of the I2C interface with no VMI/decoder connected.
- Added some comments about current status of the Banshee code.
take RAW_BYTES string out of bx_param_string_c into new param type bx_param_bytestring_c (better name, anybody?)
this is intermediate step, later it would be better to merge bx_param_string into generic template bx_param<type>
but bx_param_bytestring_cis not matching that concept (or probably will continue to inherit from bx_param<string>)
- Basic I2C implementation for DDC2B support.
- Added VESA EDID structure (values from a patch for the LGPL'd VGABIOS).
- Windows now detecting plug&play monitor "Bochs Screen" if an original VGABIOS
image is used (Cirrus PCI / Voodoo Banshee).
- TODO: Add this feature in the Cirrus version of the LGPL'd VGABIOS.
use new method do dump param tree during save/restore, GUI and text debugger and other places
significantly reduce code duplication over multiple modules
the method dumps param to the FILE
use new method do dump param tree during save/restore
also make more use of parse_param methods which initialize param from a string