SMAP will generated page faults when the kernel tries to access user pages unless overriden.
If SMAP is enabled, the override instructions are written where needed in memory with
binary "altcodepatches".
Support is enabled by default, might be disabled per safemode setting.
Change-Id: Ife26cd765056aeaf65b2ffa3cadd0dcf4e273a96
* New Intel SkyLake seems to have 9 mapped ranges
at boot. It seems like this define has been creeping
up for a while.
* Resolves the inital issue reported in #11377 on SkyLake
as well. Bonefish mentioned it might need to be raised
again... he had some good foresight there :-)
* I'm seeing the same no bootable partitions issue though
via USB after this raise. (maybe a USB 3.1 thing?)
The BOOT_GDT_SEGMENT_COUNT was based on USER_DATA_SEGMENT on both
x86 and x86_64. However, on x86_64 the order of the segments is
different, leading to a too small gBootGDT array. Move the define to
the arch specific headers so they can be setup correctly in either case.
Also add a STATIC_ASSERT() to check that the descriptors fit into the
array.
Pointed out by CID 1210898.
The kernel is allowed to use fpu anywhere so we must make sure that
user state is not clobbered by saving fpu state at interrupt entry.
There is no need to do that in case of system calls since all fpu
data registers are caller saved.
We do not need, though, to save the whole fpu state at task swich
(again, thanks to calling convention). Only status and control
registers are preserved. This patch actually adds xmm0-15 register
to clobber list of task swich code, but the only reason of that is
to make sure that nothing bad happens inside the function that
executes that task swich. Inspection of the generated code shows
that no xmm registers are actually saved.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
Enable SSE as a part of the "preparation of the environment to run any
C or C++ code" in the entry points of stage2 bootloader.
SSE2 is going to be used by memset() and memcpy().
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
The possibility to specify custom memcpy and memset implementations
in cpu modules is currently unused and there is generally no point
in such feature.
There are only 2 x86 vendors that really matter and there isn't
very big difference in performance of the generic optmized versions
of these funcions across different models. Even if we wanted different
versions of memset and memcpy depending on the processor model or
features much better solution would be to use STT_GNU_IFUNC and save
one indirect call.
Long story short, we don't really benefit in any way from
get_optimized_functions and the feature it implements and it only adds
unnecessary complexity to the code.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
If GCC knows what these functions are actually doing the resulting
code can be optimized better what is especially noticeable in case of
invocations of atomic_{or,and}() that ignore the result. Obviously,
everything is inlined what also improves performance.
Signed-off-by: Paweł Dziepak <pdziepak@quarnos.org>
This patch makes it possible to inline rdmsr and wrmsr instruction. The
performance impact shouldn't be significant since they are used relatively
rarely and wrmsr is usually a serializing instruction, but there is no reason
not to do so.
The goal of this patch is to amortize the cost of context switch by making
the compiler aware that context switch clobbers all registers. Because all
register need to be saved anyway there is no additional cost of using
callee saved register in the function that does the context switch.
Similarly to previous patch regarding GDT this is mostly a rewrite of
IDT handling code from C to C++. Thanks to constexpr IDT is now entirely
generated at compile-time.
Virtually no functional change, just rewriting the code from
"C in *.cpp files" to C++. Use of constexpr may be advantageous but
that code is not performance critical anyway.
Apparently, reading from dr3 is slower than reading from memory
with cache hit.
Also, depending on hypervisor configuration, accessing dr3 may cause
a VM exit (and, at least on kvm, it does), what makes it much slower
than a memory access even when there is a cache miss.
* Create new interface for cpuidle modules (similar to the cpufreq
interface)
* Generic cpuidle module is no longer needed
* Fix and update Intel C-State module
* Mostly useful for virtualization at the moment. Works in QEmu.
* Can be enabled by safemode settings/menu.
* Please note that x2APIC normally requires use of VT-d interrupt remapping feature
on real hardware, which we don't support yet.
Placing commpage and team user data somewhere at the top of the user accessible
virtual address space prevents these areas from conflicting with elf images
that require to be mapped at exact address (in most cases: runtime_loader).
Set execute disable bit for any page that belongs to area with neither
B_EXECUTE_AREA nor B_KERNEL_EXECUTE_AREA set.
In order to take advanage of NX bit in 32 bit protected mode PAE must be
enabled. Thus, from now on it is also enabled when the CPU supports NX bit.
vm_page_fault() takes additional argument which indicates whether page fault
was caused by an illegal instruction fetch.
The physical memory map area was not included in the kernel virtual
address space range (it was below KERNEL_BASE). This caused problems
if an I/O operation took place on physical memory mapped there (the
bad address error seen in #9547 was occurring in lock_memory_etc()).
Changed KERNEL_BASE and KERNEL_SIZE to cover the area and add a null
area that covers all of it. Also changed X86VMTranslationMap64Bit to
handle large pages in Query(), as the physical map area uses large
pages.
The lowest 4 bits of the MSR serves as a hint to the hardware to
favor performance or energy saving. 0 means a hint preference for
highest performance while 15 corresponds to the maximum energy
savings. A value of 7 translates into a hint to balance performance
with energy savings.
The default reset value of the MSR is 0. If BIOS doesn't intialize
the MSR, the hardware will run in performance state. This patch
initialize the MSR with value of 7 for balance between performance
and energy savings
Signed-off-by: Fredrik Holmqvist <fredrik.holmqvist@gmail.com>
Renamed {32,64}/int.cpp to {32,64}/descriptors.cpp, which now contain
functions for GDT and TSS setup that were previously in arch_cpu.cpp,
as well as the IDT setup code. These get called from the init functions
in arch_cpu.cpp, rather than having a bunch of ifdef'd chunks of code
for 32/64.
Reused x86 arch_user_debugger.cpp, with a few minor changes to make
the code work for both 32 and 64 bit. Something isn't quite working
right, if a breakpoint is hit the kernel will hang. Other than that
everything appears to work correctly.
