- Don't trust HA_ST_MORE again if the above situation occurs.
- Nuke bitfields in 'struct eata_sp'.
- Don't bother using scatter-gather if DMA map contains only 1 segment.
- Return TRY_AGAIN_LATER and not COMPLETE if an EATA command times out.
- Check SCSI status in dpt_inquire(), not just HBA status.
- Some cosmetic changes and sanity checks.
CardBus bus stub, YENTA PCI-CardBus bridge (cbb), 3Com 3C575TX driver
(ex) and Intel fxp driver.
TODO:
o Conform to the KNF more strictly.
o Be unified with pcmcia code as much as possible.
o Add more drivers for CardBus card, such as APA-1480 or USB card.
The affected files are listed below.
sys/arch/i386/conf/files.i386
sys/arch/macppc/conf/files.macppc
sys/conf/files
sys/dev/ic/elinkxl.c
sys/dev/ic/elinkxlvar.h
sys/dev/ic/i82365.c
sys/dev/ic/i82365var.h
sys/dev/isa/i82365_isasubr.c
sys/dev/pci/files.pci
sys/dev/pcmcia/pcmcia.c
sys/dev/pcmcia/pcmciachip.h
The added files are listed below.
sys/arch/i386/conf/CARDBUS
sys/arch/i386/include/rbus_machdep.h
sys/arch/i386/i386/rbus_machdep.c
sys/arch/macppc/include/rbus_machdep.h
sys/arch/macppc/macppc/rbus_machdep.c
sys/dev/cardbus/if_ex_cardbus.c
sys/dev/cardbus/Makefile.cardbusdevs
sys/dev/cardbus/cardbus.c
sys/dev/cardbus/cardbus_map.c
sys/dev/cardbus/cardbusdevs
sys/dev/cardbus/cardbusdevs.h
sys/dev/cardbus/cardbusdevs_data.h
sys/dev/cardbus/cardbusvar.h
sys/dev/cardbus/cardslot.c
sys/dev/cardbus/cardslotvar.h
sys/dev/cardbus/devlist2h.awk
sys/dev/cardbus/files.cardbus
sys/dev/cardbus/if_fxp_cardbus.c
sys/dev/cardbus/pccardcis.h
sys/dev/cardbus/rbus.c
sys/dev/cardbus/rbus.h
sys/dev/pci/pccbb.c
sys/dev/pci/pccbbreg.h
sys/dev/pci/pccbbvar.h
so we'll know when it's time to switch from 'slow' command mode to normal.
Change some settings for configuration printfs and debug levels. Redo the
internal ispscsicmd return definitions and let isp_cmd translate them as
approrpriate to NetBSD values. Remove the inline functions from here- they're
now in isp_inline.h. Put in the start of the correct SWIZZLE/UNSWIZZLE
functions.
Redo how we start commands- do a 'slow' start function which then
looks to see when we're done the configuration process at which point
it *then* enables sync/wide mode. Set the max openings amount to the
true max openings- not a synthetic. Add a timeout driven command requeue
function so that Loop Down events well freeze things until a later point
in time where they might be restarted.
isp_fastpost_complete function to include a handle. Do some
isr register debouncing. Use new inline functions for xflist
handle storage. Remove isp_dumpxflist function. Do some fixups
of NVRAM from some broken cards. Use Full Login after LIP option
for FC cards if f/w < 1.17 - there's a f/w bug that causes the
port database to not be actually refreshed for local loop devices!
Do the appropriate endian swizzling for the ICB. Ditto for SNS structures
(these are no-ops until UltraSparc PCI needs them).
defines to get max luns for a card. Make sure the RESULT_QUEUE_LEN is not less
than 64- I've seen breakage with that. Move the temp port database stuff
into the softc (ick). Remove most of the target mode stuff. Make xflist
storage an external outer layer thing (since it will now be allocated based
upon the maximum commands that this HBA can support rather than request
queue size).
the correct "read eeprom" opcode on the RoadRunner (which has a larger
EEPROM, and thus needs a different opcode to make room for the larger
offsets).
- Reset and enable the MII before probing for PHYs, and reset and enable
the MII in epinit().
- Be more conservative when resetting the interface after a transmit error.
Based on PR #8331, from Ryoji KATO.
Closer on 3c574, probably will work fine with the 3CCFEM556BI (which
won't have an older rev TDK Semi PHY, and which was tested by the author
of the PR).
- Mute wave output, not the mixer output, on changing CODEC settings.
- Add support for muting wave output while playback or monitoring is inactive.
- Change formula of calculating gain so that all the levels should be
used equally (the old code uses the min/max gain only at 0/255).
- Cleanup
- In dpt_intr(), if no interrupt is signalled but the HBA has indicated
that more data will be available soon (HA_ST_MORE), save a context switch
and wait for the data.
to the SCSIPI subsystem.
- Determine more characteristics about the board, including the number
of concurrent commands that the processor can execute at a time.
- Rework memory allocation strategy so that we can do dynamic pre-allocation
of resources according to workload.
Thanks to the Linux Buslogic driver for having some useful comments.
until Matt Jacob has a change to update the driver for the latest
firmware, etc. since update device parameters seems to fail once the
system is really up and running, and eventually causes the controller
to wedge. This may be due to a firmware bug.
Per discussion with Matt.
- 82C115 has a 128-bit multicast hash table, not 512-bit.
- Correct the way the MAC address is read from the SROM, after re-reading
the MX98715A Application Note.
Other semi-related changes:
- Differentiate between MX98715 and MX98715A.
- Improve the Macronix link-up/link-down detection.
this by frobbing the 10TCTL register minimally, toggling only the bit we
care about (and hoping that link-capability advertisement happens correctly).
MX98715 can talk to the network now.
- Add a comment about the Macronix MX98713 -- it's almost exactly like
a 21140A, and doens't have the Nway registers that the other Macronix
chips have.
- Bus specific front-end is now responsible for reading EATA configuration
- EATA configuration data is now saved in the softc
- Make synchronous writes work properly
- Don't ignore HBA timeouts in dpt_cmd()
- Prefix eata_cfg's members with `ec_', not `dc_'
boards which use MII for media attachment.
ISV SROM format information lifted from Matt Thomas's `de' driver.
Thanks to Dave Sainty for experimenting w/ his 21140A MII boards, and
for supplying a fix to the MII bit-bang code (PR #8382).
- Only use 16 longword bursts.
- Reset the interface for receive filter setups that don't come from
the reset path.
Hi, Jason is getting really tired of broken clone chips, and really wishes
real 21140 boards were still available, because the DEC chips seem to work
Just Dandy.
support for the ISV SROM format used in the 2114{1,1A,2,3}. Note, like
the 21040, auto-sense is not yet supported for the 21041.
Add a "pre-init" hook, which will be used for the 2114x and PNIC (currently)
which allows chip-specific code to set up and write OPMODE before the
chip is reset. This is necessary in order for the chip's internal
pathways to get initialized properly for MII/SYM/PCS/SIA media attachments.
Thanks to Dave Sainty for the hint from the `de' driver that inspired the
pre-init hook.
- Fix the SROM checksum routine.
- Add code to parse the old DEC Address ROM SROM format.
- Rearrange the statchg routines a bit, to make them consistent with one
another.
- Add support for the DECchip 21040. XXX No support for media autosense
yet, and no support for any of the multi-port boards yet.
Tree structure:
- sys/arch/sh3: sh3 generic code
As commented, in-chip device drivers are put into sys/arch/sh3/dev.
- sys/arch/evbsh3: sh3 evaluation boards (pure sh3 CPU, no fancy external HW)
- sys/arch/mmeye: Brains mmEye, www.brains.co.jp
MI source code includes couple of #ifdef for sh3-coff support.
(sh3 uses coff or elf)
Needs some more improvements, especialy in sys/arch/sh3/conf/files.sh3,
to compile the tree (due to last minute tree structure change).
Drop multicast/broadcast packet looped back from myself.
This is to cope with SMC91C92 (Megahertz XJ10BT), which
loops back multicast packet to itself on promiscuous mode.
(should be ensured by chipset configuration)
Reviewed by: thorpej
put it in Store-and-Forward mode right from the get-go. This eliminates
the DMA underrun errors that prevented the receive filter setup from working
and caused smashed packets to go out onto the wire.
My NetGear FA310-TX board now works.
There are still "filter setup failed to complete" messages, however they
don't appear to indicate that the filter setup actually failed, since
unicast and multicast packet reception work fine. I will address this
problem shortly.
Reading the log for the FreeBSD `pn' driver suggests that these chips are,
in fact, pretty crappy, riddled with hardware bugs (for which more workarounds
are coming).
rewrite of the driver for the DECchip 21x4x Ethernet chips, and a variety
of clones.
Currently, the driver supports the Winbond 89C840F (this works pretty
well), and the Lite-On PNIC (e.g. NetGear PCI boards), however Lite-On
support may be broken [I may simply have a busted test board].
Eventually, support for the Macronix and ASIX chips will filter into
this driver, and then, slowly, support for the genuine DEC chips,
and maybe even the DE-425 EISA model.
and consider it to be like an RCC (receive copy complete). The RCC
code path has always checked for bad received packets.
- Trim the CRC length off the recived packet length; the EPIC/100 always
includes the CRC in the packet.
- Improve fatal error reporting.
- fix printing of Ultra-DMA modes (shows up when the drive supports highther
modes than the controller).
- Don't use C_NEEDDONE anymore. We were setting this flag in a possibly
freed wdc_xfer (this didn't create problems, as it was free'd in the POLL
case only, while IRQs are blocked, but it's not good practice anyway
and pool(9) complains about it ;)
was being initialized to a KVA, when we really wanted a DMA address. Change
the code to allocate the overrun buffer with the control blocks, and
properly initialize overrun_buf.
Note that overrun_buf cannot actually be shared between all boards; DMA safe
memory could vary from bus to bus.
Garbage-collect two functions which are no longer used because of the
above changes.
2 times in the past
- Set up timeout per xfer instead of per interrupt. This helps with
PIO transfer (we would call timeout()/untimout() several times for a
transfer).
- If we missed an interrupt for a PIO transfer, reset and restart it
immedialy, don't try to recover and continue. If we missed an interrupt we
may have lost a read/write cycle on the IDE bus. If this happens 1) we
corrupt data and 2) we enter an interrupt loop at the end of the xfer, as
the drive has some more data to read/write, but the host thinks the xfer is
done.
This last change fix the (or at last some of the) 'lookup after lost interrupt'
some peoples have been experiencing.
anyway, take advantage of this and greatly simplify the programming
of the multicast filter. This solves the last reported "device timeout"
problem with this driver.
to the EPIC/100 driver's (adjusting for the fact that Intel Ethernet chips
are from Pluto):
* Don't allocate receive buffers until the interface is actually brought
up, and release all of them if the interface is taken down.
* Add a knob (defaults to off) which will copy an incoming packet to
a single header mbuf if it is small enough to fit in one, rather than
burning an entire cluster on it. Note that this change will be mostly
moot if/when sbcompress() is changed to handle compressing clusters.
Simplify some of the receive list logic:
* Rather than using a homegrown queue and additional software RX descriptors,
use an ifqueue to queue receive buffers, and M_{GET,SET}CTX() to hook DMA
maps and receive buffers together.
Clean up a bit:
* Macroize a bunch of things to make the code a bit easier to follow.
* Don't allocate receive buffers until the interface is actually brought
up, and release all of them if the interface is taken down.
* Add a knob (defaults to off) which will copy an incoming packet to
a single header mbuf if it is small enough to fit in one, rather than
burning an entire cluster on it. Note that this change will be mostly
moot if/when sbcompress() it changed to handle compressing clusters.
Constantine Sapuntzakis confirmed by Bill Sommerfeld. Although nothing is
supposed to call wakeup on this without setting AT_DONE, it's good practice to
do it this way (the process may be waken up by a setrunnable() call).
(Sorry for a big commit, I can't separate this into several pieces...)
Pls check sys/netinet6/TODO and sys/netinet6/IMPLEMENTATION for details.
- sys/kern: do not assume single mbuf, accept chained mbuf on passing
data from userland to kernel (or other way round).
- "midway" ATM card: ATM PVC pseudo device support, like those done in ALTQ
package (ftp://ftp.csl.sony.co.jp/pub/kjc/).
- sys/netinet/tcp*: IPv4/v6 dual stack tcp support.
- sys/netinet/{ip6,icmp6}.h, sys/net/pfkeyv2.h: IETF document assumes those
file to be there so we patch it up.
- sys/netinet: IPsec additions are here and there.
- sys/netinet6/*: most of IPv6 code sits here.
- sys/netkey: IPsec key management code
- dev/pci/pcidevs: regen
In my understanding no code here is subject to export control so it
should be safe.
false matches on controllers which properly respond to a WDCC_RECAL command.
Should close PR port-i386/7702 (the author tested this patch, and said it
solves his problem).
return 0 instead of EINVAL. In this case, there will only be one media
type, and the upper-level if_media code will ensure that the user is
setting to that type.
This matches changes Jason made a while back to sys/dev/ic/lance.c
between a bug in the receive path (buffer length used instead of actual
received frame length) and the ARP code not correctly setting the length
of the reused mbuf, which all told caused the transmit logic in the chip
to wedge.
Also, make sure to count received packets.
Found and fixed by Zdenek Salvet <salvet@ics.muni.cz>, PR #7809.
which use uvm_vslock() should now test the return value. If it's not
KERN_SUCCESS, wiring the pages failed, so the operation which is using
uvm_vslock() should error out.
XXX We currently just EFAULT a failed uvm_vslock(). We may want to do
more about translating error codes in the future.
enami