too much damange. everything else here is the same in a 64bit vs. 32bit
world, so keep it all simple. the alpha was the only port to have any real
affect for this, and it only very recently begun to support some audio
devices so it doesn't really apply here. 1.3/alpha did not support audio..
properly! Work around this by determing current active media by taking
the highest-order common bit of our advertised capabilites and the link
partner's.
If the link partner doens't do autonegotiation, then parallel detection will
pick up the media type, which will never be full-duplex, so reading the PAR
is ok in this case.
Bug pointed out by Matthias Drochner, work-around inspired by reading
the dp83840 manual, section 3.9 (IEEE 802.3u auto-negotiation).
Replace it by a variable, which is initialized in amiga_init.c.
This will make the kernel actually work even if we have lots of Zorro-III
(or DraCo direct bus) i/o space.
the 3Com 3c905-TX and 3c905-T4. Fix handling of the MII on the
3c595-MII and 3c597-MII (can't talk to the PHYs on these cards; just
use "manual" for the external MII port).
Fixes kern/4782 (Chris Demetriou).
the hp300 port.
- Interrupts 3-6 use this immediately. Interrupt 7 is a special case,
and the VIA interrupts (1 and 2) will be addressed when that code is
rototilled.
- Modify the zs front end to register with the appropriate interrupt
controller: through the PSC on the AV Quadras, and direct to
interrupt 4 on the rest. Arrange to have the appropriate zsc_softc
supplied to us at interrupt time.
- Modify the direct ADB driver (and its PowerManager cousin) to call
intr_dispatch(), rather than zshard(). XXX This is a kludge, but at
least limits the brokenness to the ADB drivers, now.
As a side effect, this should fix PR 5590. Thanks to Bill Studenmund for
correctly determining the cause of the problem reported there.
the hp300 port.
- Interrupts 3-6 use this immediately. Interrupt 7 is a special case,
and the VIA interrupts (1 and 2) will be addressed when that code is
rototilled.
- Modify the zs front end to register with the appropriate interrupt
controller: through the PSC on the AV Quadras, and direct to
interrupt 4 on the rest. Arrange to have the appropriate zsc_softc
supplied to us at interrupt time.
- Modify the direct ADB driver (and its PowerManager cousin) to call
intr_dispatch(), rather than zshard(). XXX This is a kludge, but at
least limits the brokenness to the ADB drivers, now.
As a side effect, this should fix PR 5590. Thanks to Bill Studenmund for
correctly determining the cause of the problem reported there.
the hp300 port.
- Interrupts 3-6 use this immediately. Interrupt 7 is a special case,
and the VIA interrupts (1 and 2) will be addressed when that code is
rototilled.
- Modify the zs front end to register with the appropriate interrupt
controller: through the PSC on the AV Quadras, and direct to
interrupt 4 on the rest. Arrange to have the appropriate zsc_softc
supplied to us at interrupt time.
- Modify the direct ADB driver (and its PowerManager cousin) to call
intr_dispatch(), rather than zshard(). XXX This is a kludge, but at
least limits the brokenness to the ADB drivers, now.
As a side effect, this should fix PR 5590. Thanks to Bill Studenmund for
correctly determining the cause of the problem reported there.
resolves a great many issues, including Performa 58x interrupt handling
and offset displays on some models.
Programs that depend on the old (pre-NetBSD 1.1) grf interface may break.
That's actually a separate issue uncovered by this code, not caused by it.
if_tlvar.h, since the ThunderLAN PHY driver needs to know some things
about it's parent (and since it can only attach to a ThunderLAN chip,
this is the easiest way).
802.3u autonegotiation, and will report the precise media selected
by autonegotiation by reading PHY-specific registers.
XXX There is still some work to do wrt. autonegotiation and the
BNC/AUI support in the ThunderLAN PHY.
opened norewind and 2 filemarks are written at the end a phantom file
is left (just what I was afraid of, but I didn't think about it in
the last delta because somehow I had managed to convince myself that
this was a nonissue. It's not.).
So- in stdone clear ST_WRITTEN for regular reads. In st_close, preserve
the state of ST_WRITTEN, and if no error and 2FM@EOD for this device and
this is a no-rewind open, backspace one filemark. This should preserve
(for this mount session) FILE - FMK - FILE - FMK - FILE ... FILE FMK FMK EOD
sequencing.
This doesn't clean up the case of EOM appends- in this case you *will* still
get (after an MTEOM operation and a write of a file) a phantom empty file,
e.g. FILE - FMK FMK - FILE - FMK FMK EOD *unless* you follow the EOM operation
with an explicit backspace. The trouble is that this makes it difficult for
seamless interchange with other systems which don't necessarily follow.
The preferrable alternative would be to eliminate the 2FM@EOD except for
1/2" Reel tapes, but that has been pretty much nixed within developers.
associated with any observed lossage...it was just noticed while reading
ncr_start().
g/c some now-unreachable code produced by the earlier race condition fix.
Also, even on the SB1, we can leave the DMA controller in auto-initalize
mode and just send a command to the board for each block. This may help
prevent FIFO underruns.
kleink