b3cf850817
Fix typos in comments.
2000-03-14 01:29:30 +00:00
f91ce51084
Regen.
2000-03-13 17:24:14 +00:00
e22c4b3d1f
Add a bunch of Compaq array controllers.
2000-03-13 17:23:26 +00:00
e750135b5e
A few things:
...
* Initialize PCIC_INTR and PCIC_CSC_INTR on all chips, not just TI.
* Leave card detect interrupts enabled in PCIC_CSC_INTR. (This requires
reading PCIC_CSC in the interrupt handler on some chips, so do that too.)
* Leave PCIC_INTR_ENABLE set, as some chips require this to post card detect
interrupts while in PCMCIA mode.
* Leave PCIC_INTR_RESET (which is inverted) set at all times *except* when
powering up a socket, as some chips will use it to drive RESET# low even
while a CardBus card is in the slot.
This makes PCMCIA and CardBus cards works with some TI chips. Cross-checked
with a Toshiba ToPIC 95B.
2000-03-12 11:31:53 +00:00
30f73f1831
support bus probes a la "badaddr" and VME interrupts, fix error handling
...
after mapping problems
2000-03-12 11:23:06 +00:00
e135f943fa
add support for DMA mapping, bus probes ala "badaddr" and VME interrupts,
...
improve diagnostic output
2000-03-12 11:21:02 +00:00
1203bdcbb3
Bus_space-ify TGA register accesses.
...
(raster operations are still using pointer-based access)
2000-03-12 05:32:29 +00:00
602faa83a8
Do *not* fiddle with the serial/parallel IRQ mode selection on TI chips.
...
Without extensive probing, we cannot possibly know that we're doing the right
thing.
Also some stylistic changes.
2000-03-12 04:34:29 +00:00
781b535703
Revert the previous change.
2000-03-12 04:27:12 +00:00
c7a13f6116
Revert the previous change. It does not match the commit message *and* was
...
incomplete (and probably quite broken).
2000-03-12 04:25:57 +00:00
5c64f2064d
Add missing sc_pil_intr_enable member to pccbb_softc.
...
XXX Double check this, please. The code appears to only use it as a
boolean, but...
2000-03-12 01:15:04 +00:00
27fe6c0aee
regen
2000-03-11 16:13:39 +00:00
d01b78affd
Add id for Alliance AT25, as sent by Dave Sainty in kern/9596.
2000-03-11 16:13:14 +00:00
2d525b16dd
The shortened 1371 reset delay in revision 1.32 doesn't seem to be
...
quite enough for my 1373, so increase it some.
2000-03-11 06:42:37 +00:00
b58bf3c7bb
Don't reset cp->hw_ok ro 0 when cp isn't initialised in cy693_chip_map()
...
(used only in failure case). Pointed out by Wolfgang Solfrank.
While I'm here correct indentation.
2000-03-10 21:21:48 +00:00
173f823e3a
Only apply power on 3.3 V CardBus card (there are no 5 V CardBus card.)
2000-03-10 11:08:49 +00:00
c70220f2a2
Move PCIIDE_CHANNEL_NAME macro to pciidereg.h.
2000-03-09 20:26:31 +00:00
0542cec055
put "#ifdef __alpha__" around "alpha_mb()" calls
...
(I know the driver is useless without console initialisation, but it
should at least compile.)
2000-03-09 18:40:36 +00:00
24ea2caf14
regen
2000-03-09 09:53:03 +00:00
3abb87c0f5
Add Conexant SoftK56 PCI Software Modem, Sony CXD3222 OHCI i.LINK(IEEE 1394)
...
PCI controller, Sony Memory Stick I/F Controller
Ids send by John Hawkinson in kern/9588
2000-03-09 09:50:49 +00:00
5eee9ca94c
Determine the size of the SROM by probing the chip using the standard Microwire
...
protocol. Eliminates the need for srom_quirks and some other trash.
2000-03-07 00:39:17 +00:00
91c44a72b8
Set ifp->if_baudrate as appropriate.
2000-03-06 21:02:37 +00:00
a6f861574a
No longer necessary to futz with ifp->if_baudrate here.
2000-03-06 21:02:00 +00:00
c34cce88c4
Add support for the AMD 756 DMA/UDMA IDE controller, provided in
...
PR kern/9536 by Dave Sainty.
2000-03-06 18:02:26 +00:00
d97becf28e
Make Creative Soundblaster PCI 128's work -- from Masahiro Ishiyama
...
Note that on device close, there's a sharp pop that probably should be fixed.
Note also that the device is hanging the machine at times for brief
periods inside audio.c::audiogetinfo(), but I haven't yet figured out
why.
2000-03-06 03:18:11 +00:00
c74ea28746
Support the W89C940F alternative ID.
2000-03-06 03:07:08 +00:00
9e870c5a88
Regenerate from pcidevs.
2000-03-06 02:32:31 +00:00
1a0eab6fa3
Add SYMPHONY 83C553 PCI-ISA bridge.
...
Add alternative ID for Winbond W89C940F.
2000-03-06 02:31:19 +00:00
23af6e53fd
Moved things around a bit so that TGA2 can be used as a console.
...
Addresses PR: port-alpha/9542
2000-03-05 07:57:52 +00:00
1dfdd10eae
I got the mode sense bits of the monitor wrong they needed a twiddle (~).
2000-03-05 02:30:57 +00:00
c98328e9df
Regen from "pcidevs".
2000-03-04 13:24:24 +00:00
947ec630de
Add AMD Athlon chipset related devices. Patch supplied by Dave Sainty in
...
PR kern/9533.
2000-03-04 13:23:26 +00:00
f939818426
Added basic TGA2 support to the TGA driver. Abstracted the RAMDAC
...
code out into ../ic/bt485.c. Disabled tga_bt463.c, which we don't
currently support.
2000-03-04 10:27:59 +00:00
285a315e99
Simplify the winlist code.
2000-03-01 23:40:26 +00:00
7da6407d04
add (minimal, PIO only) support for the popular "Tundra Universe"
...
PCI-VME interface chip and a frontend for the "Bit3 Mod. 2706"
PCI-VME adapter
2000-02-25 18:22:39 +00:00
c86b7572f9
Cosmetic change.
2000-02-25 00:23:57 +00:00
5ed29fa2d6
Delete a superfluous newline in attach message.
2000-02-24 03:42:44 +00:00
7f8cdf038f
Fix a missing closing parenthesis in an error diagnostic
2000-02-23 08:31:25 +00:00
d94804a788
Pccbb maintains the interrupt handlers for 16-bit PC Cards
...
by itself.
Add some comments.
2000-02-23 07:28:54 +00:00
347823e807
Include dev/isa/isavar.h so that this file compiles again.
2000-02-22 22:46:16 +00:00
3f9cf7572c
Don't use void * for chipset tags. Bad hacker, no biscuit.
2000-02-22 16:04:44 +00:00
b785bb47a0
Establish a powerhook and make sure the card detect interrupt is enabled
...
after resume from suspend, as i82365.c does.
This is a workaround for newer Sony VAIO notebook.
Patch is submitted by Atsushi Onoe (onoe@sm.sony.co.jp ) in PR#9463.
2000-02-22 02:35:26 +00:00
70bbb1b84e
Sync PCMCIA memory mapping with a change from rev 1.47 of i82365.c:
...
always map attr memory 8 bit, since its defined that way. (chopps)
2000-02-21 01:44:36 +00:00
3a76270201
deal with a DELAY vs. delay issue
2000-02-20 22:19:29 +00:00
717d5b1cc3
Support for > 12 byte commands for parallel SCSI.
2000-02-19 01:54:42 +00:00
4331d2bcaa
Regen.
2000-02-16 04:29:32 +00:00
021ff75015
Add Toshiba ISA bridge.
2000-02-16 04:29:20 +00:00
6eba47aa8f
add (untested in NetBSD yet) Qlogic 12160 (Ultra3) suppot
2000-02-12 02:22:37 +00:00
f522d6f1ee
Supports "USR 3CP5609 PCI 16550 Modem", from Kent Polk.
2000-02-08 16:26:23 +00:00
b3cffb232f
regen
2000-02-08 16:24:00 +00:00
b614c6a569
Add US Robotics vendor ID, and USR 3CP5609 PCI 16550 Modem product ID.
...
From Kent Polk.
2000-02-08 16:22:37 +00:00
dbeafc9dbe
clean up some printfs
2000-02-06 08:14:13 +00:00
6d8c9583a7
indent this file
2000-02-05 18:42:37 +00:00
101848d272
run this through indent with some comment cleanup -- more knfing needed.
2000-02-05 18:20:08 +00:00
29be498635
Add a list of all the currently supported boards
2000-02-04 13:16:22 +00:00
cbacaf54d7
Add AdvanSys U2W (LVD) boards support
2000-02-03 20:28:26 +00:00
fd2fd888ef
Add AdvanSys U2W host adapters
2000-02-03 16:56:23 +00:00
787999d9e4
Add AdvanSys U2W boards
2000-02-03 16:51:42 +00:00
5b67628108
regen
2000-02-03 13:58:55 +00:00
1533d39d9e
2 Micro -> O2 Micro
2000-02-03 13:58:28 +00:00
eed75dbc26
Don't dry to diving MIIF_NOISOLATE in the PHY drivers. Instead, pass
...
flags down from the parent to child vi mii_attach().
2000-02-02 17:09:38 +00:00
84dc99fdea
Bring some order to the chaos which was the MII code function naming
...
"conventions".
2000-02-02 08:05:26 +00:00
d8e72e215d
implement probing for available irqs on non-cirrus pcmcia controllers
...
including cardbus controllers running in pcic mode
2000-02-01 22:39:51 +00:00
547bd53f89
Add support for the SiS 7016.
2000-01-31 18:36:12 +00:00
f457f7c969
Regen.
2000-01-31 18:34:51 +00:00
a2efc77ee1
Add SiS 7016 10/100 Ethernet.
2000-01-31 18:34:19 +00:00
b1ec3fa901
Give the ISV filter a chance to verify 21143 pass 4.1 SROMs before running
...
them through the quirk table.
2000-01-26 16:51:11 +00:00
063cb5e5dc
Additional hackery for the Cobalt interfaces. Even though these are
...
pass 4.1 21143s, they have a 128-byte SROM, and thus use a different
SROM address size than all other pass 4.1 21143s.
A plea to hardware designers -- *please* read application notes for
the components you're using before putting your hardware together. Thanks.
2000-01-26 15:50:52 +00:00
639bd74d21
Pccbb manages interrupt handlers by itself for its child device.
2000-01-26 09:02:41 +00:00
4656f0ba52
Remove the FreeBSD support from this file. It hasn't worked in FreeBSD
...
for some time, and only made the code harder to read.
2000-01-26 06:41:11 +00:00
494b4a9ed3
Fix an oversight in the AIC-7xxx SEEPROM split.
2000-01-26 06:27:32 +00:00
8949eab0cb
Split the code that reads the SEEPROM into its own file.
2000-01-26 06:04:37 +00:00
2bd8866643
"i/o" -> "memory"
2000-01-25 23:23:48 +00:00
7360584deb
use BUS_SPACE_MAP_PREFETCHABLE instead BUS_SPACE_MAP_CACHEABLE where the
...
PCI BAR bit is referred to
(XXX is the hack still necessary?)
2000-01-25 22:31:06 +00:00
4f1e715248
use BUS_SPACE_MAP_PREFETCHABLE instead BUS_SPACE_MAP_CACHEABLE where the
...
PCI BAR bit is referred to
2000-01-25 22:30:04 +00:00
6dc0e3435d
IFM_1000_FX -> IFM_1000_SX
2000-01-25 20:19:14 +00:00
02af3f45b6
Clean up the SROM addrbits code a little.
2000-01-25 19:53:34 +00:00
6aca67041c
Add a chip type for the Xircom X3201-3, and centralize the declaration
...
of the chip names array.
2000-01-25 19:29:17 +00:00
492bfe70f3
get the device name from pcidevs instead of having a list here
2000-01-25 14:34:24 +00:00
73ce2abd33
Make sure PIRQD enable bit is set. From FreeBSD.
2000-01-25 11:26:06 +00:00
dccf05f858
Do pccbb_chipinit() after YENTA register space allocation.
...
Add TI PCI 1451 PCI-CardBus entry.
2000-01-25 09:36:43 +00:00
f18e32d670
Regen.
2000-01-25 09:06:50 +00:00
7b4d7aaba1
Add TI PCI 1451 PCI-CardBus bridge.
2000-01-25 09:04:03 +00:00
b50b01e020
Don't enable the interrupt until after we cycle the power, disable
...
interrupt at disable, and make this code look more like the std pcic
code. From Mycroft and I.
2000-01-25 06:16:34 +00:00
c4d8a60bac
Handle Cobalt Networks interfaces, which are 21143 pass 4.1 devices
...
with a simple (MAC address only) SROM format.
From Soren S. Jorvang <soren@wheel.dk>
2000-01-25 03:23:56 +00:00
7ac1ad97ba
The TI 2030 is a PCI-PCI bridge and doesn't belong here
2000-01-24 15:51:59 +00:00
4b45d02e15
regen
2000-01-24 15:50:16 +00:00
a8308ddfd4
TI PCI2030 is a PCI-PCI bridge
2000-01-24 15:49:50 +00:00
1ef6ee50b9
Regen.
2000-01-23 09:55:40 +00:00
9aa167f517
Add Apple KeyLargo and UniNorth.
2000-01-23 09:54:28 +00:00
901082bf1e
Remove code that should not have been added.
2000-01-23 04:02:19 +00:00
75e8c400fa
Add parens so a ?: expression binds correctly.
2000-01-23 00:10:03 +00:00
dc59bc1db3
Update for sys/buf.h/disksort_*() changes.
2000-01-21 23:39:55 +00:00
e716b4ba71
Fix register offset problem. This should make EISA boards work correctly,
...
and is also needed for the ISA frontend (some time this week).
2000-01-18 16:50:38 +00:00
0016706a70
Clean up revision stuff for the sis. Suggested by Chris Cappuccio.
2000-01-18 13:58:07 +00:00
a569e4a38f
Correct URLs.
2000-01-18 13:30:32 +00:00
762741c71d
Fix the size of the playback buffer. Patch from Dave Sainty <dave@dtsp.co.nz>.
2000-01-18 04:48:47 +00:00
2367ad5f3d
add shutdown hook
2000-01-17 12:57:26 +00:00
9156026f0f
From chris@openbsd.org:
...
"Don't enable UDMA modes for revisions of SiS 5513 < 0xd0
The only revisions I know which don't actually support UDMA are 0x09 and below..
But the only revision I know which does support UDMA is 0xd0 (and presumably
above that)"
2000-01-16 21:31:28 +00:00
a9e57ac54d
Fixes for 21143 and MII in full-duplex mode.
2000-01-15 18:39:31 +00:00
a30f6c8ad9
Apply patches from Tatoku Ogaito (the author of the code).
2000-01-14 14:39:13 +00:00
7fcb8a3a8c
minor cosmetic
2000-01-14 13:20:17 +00:00
1ee1632a02
Remove EX_CONF_MII for the 3c980. At least 2 people need this for the card
...
to work.
2000-01-13 23:26:35 +00:00
87414deb1e
remove stale comment
2000-01-13 09:05:41 +00:00
8430609055
(pccbb_pcmcia_do_mem_map): handle 8-bit memory
2000-01-13 09:01:17 +00:00
e8937eb4e5
make this slightly more inline with other code; and while at it, fix
...
some oddities in pccbb_winset
2000-01-13 08:54:20 +00:00
69034619d0
add %b strings for sockevent and sockstate registers
2000-01-13 08:46:46 +00:00
27214a2c93
Add an entry for Toshiba ToPIC100 CardBus-PCI bridge.
...
Maintainance for 3Com multi-function, 16-bit pcmcia card.
2000-01-12 09:23:26 +00:00
d978274ade
Regen.
2000-01-12 09:11:42 +00:00
6a0979928c
Add an entry for Toshiba ToPIC100 CardBus-PCI bridge.
2000-01-12 09:08:36 +00:00
3a0141108b
Regen.
2000-01-11 17:21:02 +00:00
d8c0efec1b
Add CompuModules DVB receiver and transmitter boards.
2000-01-11 17:20:24 +00:00
18bb5846c7
Regen.
2000-01-09 09:20:01 +00:00
2c073c654d
Add MPC105.
2000-01-09 09:19:26 +00:00
8f3fd0d6b3
Spelling.
2000-01-05 16:28:39 +00:00
6f64d1e85f
regen
2000-01-05 11:32:43 +00:00
2abcb85b5f
add some stuff which was mentioned on the mailing lists recently
2000-01-05 11:32:06 +00:00
a4d9bd9484
Add support for setting the clock and adapt the code to the new more
...
generic ic/hd56470.c core which now supports the isa version of the
same card.
2000-01-04 06:31:39 +00:00
e9e9f381a1
Add an entry for the Trident Microsystems CYBER 9525
...
(as found in an Toshiba Satellite 2650 XDVD).
1999-12-31 00:12:41 +00:00
ac50ee0e91
Add an entry for the Trident Microsystems CYBER 9525
...
(as found in an Toshiba Satellite 2650 XDVD).
1999-12-30 23:53:42 +00:00
1e9bb239a3
Off-by-one error in limiting the DMAC buffer size for Audio 2 to 64K (actually
...
64K - 1); from Dave Sainty in PR kern/9064.
1999-12-28 19:26:26 +00:00
f6655d0f7e
Fix a buffer KVA comparison botch in eso_mappage(); from Dave Sainty in
...
PR kern/9062.
1999-12-28 01:39:38 +00:00
841d4966c3
Lower-case Bus-Master for consistency.
1999-12-26 21:46:23 +00:00
f1a6ac445d
Use htole32() and le32toh() instead of SCR_BO().
...
XXX Should we still keep non-NetBSD part?
1999-12-26 10:41:22 +00:00
35a9d47da9
Maintanance for Ricoh RL5C475. VAIO 505TX uses this chip.
1999-12-20 08:11:42 +00:00
2f3ba68db9
Add more SCR_BO(). NCR53c875 now works on macppc.
...
XXX All SCR_BO() macros should be replaced with htole32() or le32toh().
1999-12-20 03:37:06 +00:00
be6fe10ee6
get back to looking at config flags
1999-12-20 00:33:17 +00:00
7374a44f77
Use bswap32() as SCR_BO() macro to avoid unexpected side effects.
...
SCR_BO(*src++) caused some trouble.
1999-12-18 07:57:03 +00:00
5257d9712e
regen
1999-12-17 17:19:11 +00:00
289c969284
add Intel 450NX stuff
1999-12-17 17:18:48 +00:00
b7b9264da6
Regen.
1999-12-17 14:00:12 +00:00
78ba345df3
Change the Galileo entries so the generated code can be compiled.
1999-12-17 13:59:44 +00:00
3017275313
Regen.
1999-12-17 01:04:47 +00:00
fd4557865d
Fix comment.
1999-12-17 01:04:29 +00:00
bf75bd8856
Regen.
1999-12-17 01:03:45 +00:00
fdab32f446
Add Galileo Technology system controllers.
...
Remove obsolete ID database URL.
1999-12-17 01:02:03 +00:00
edf809c8b6
Dual LVD (1280) support.
1999-12-16 05:35:42 +00:00
5dc4b19d4d
Report the Capability List support bit of the SR and, if set, print the
...
the Capability list pointer register as such as well as the capabilities
implemented in the list.
1999-12-15 12:27:26 +00:00
6a318fe223
Regen.
1999-12-15 11:55:35 +00:00
eec28e9605
* Add ESS Maestro2 product ID.
...
* Add TerraTec vendor ID.
1999-12-15 11:52:55 +00:00
3c1b8138f7
Add a device driver for the Cirrus Logic CS4280 sound chip.
...
The code has been contributed by Tatoku Ogaito.
1999-12-13 20:19:23 +00:00
821c7a01f8
As suggested by Jason Thorpe back out revision 1.27 because it broke
...
PHY probing for the ThunderLan driver.
1999-12-12 17:55:21 +00:00
014cd3fcc1
Take a stab at making this work on big-endian systems.
1999-12-12 17:46:36 +00:00
afbb07a0e5
Use htole32() and le32toh().
1999-12-12 02:53:56 +00:00
3716f21b7e
Use htole32().
1999-12-12 02:50:40 +00:00
caae0e1aa1
- Don't try to run the chip in big-endian mode. Not all chips support
...
this consistently, and it doesn't always work even when the chip
supports it.
- Make sure things DMA'd to the chip that the chip interprets are in
little-endian mode.
1999-12-11 00:32:59 +00:00
c88b5146dc
Add support code to have the Hardware Volume Control interact with the
...
software mixer Master Volume state in a defined way by lazily updating the
latter if input from the former was processed.
1999-12-10 19:13:00 +00:00
6d1d09f757
Add a symbolic name for the ES1946 rev. E in this place, too.
1999-12-10 16:50:52 +00:00
546480874c
After reading the 21143 manual again, make sure SNOOZE is cleared in
...
the CFDA register, too.
1999-12-07 07:36:19 +00:00
747d454ffe
Add the PMCSR offset for the 21143, and make sure to bring the 21142
...
and 21143 out of sleep mode. From Masanori Kanaoka.
1999-12-07 07:32:58 +00:00
f773270d0d
If, on the 21143, we find that we don't have an ISV SROM, try reading
...
it again, with 8 address bits. 21143 Pass 4.1 has a larger SROM,
for storing the CIS when used in a CardBus application.
1999-12-07 07:20:17 +00:00
0893832078
update for changed struct wsdisplay_accessops:show_screen signature.
...
no functional changes
1999-12-06 19:25:56 +00:00
9eea13a674
Mark exactly 3 uses of the SCR_BO() macro as being bogus; these 3 uses
...
already involve byte swapping on big-endian systems due to bus_space_*().
However, the use is self-consistent, and the value is not interpreted
by the chip, so it probably does not matter. Leave them in for now; we
can always look at their removal later.
1999-12-05 19:40:18 +00:00
8c1cbdbed5
Slight change to previous, to make it more obvious as to what's going on.
1999-12-05 19:33:13 +00:00
d06db4b7da
I have the feeling that OpenBSD has never tried the 53c825a, 53c875, 53c875j,
...
53c885, 53c895, or 53c896 on big-endian systems.
1999-12-05 18:40:46 +00:00
389c599f35
Changes from the OpenBSD `ncr' driver to byte-swap the script on big-endian
...
systems. Should make this go on e.g. the Apple Network Server.
1999-12-05 18:25:18 +00:00
6aabd4d0c2
CL* discarding.
1999-12-04 12:11:13 +00:00
b8a6774e36
Add support for Lava Computers MFG 2sp-pci and quattro cards.
1999-12-04 05:43:44 +00:00
165dc789fb
Regen
1999-12-04 05:43:02 +00:00
fce37d6113
Add vendor ID for Lava Semiconductor ( http://www.lavalink.com )
1999-12-04 05:41:08 +00:00
111b1dc2ee
Regen.
1999-12-04 04:41:40 +00:00
ddbe03436b
Add some of the Compaq RAID controller IDs.
1999-12-04 04:40:57 +00:00
e5835e36c3
request/response queues now indexed via u_int16_t. Add back in f/w inclusion
...
and clean up it's compilation. get chip rev out of pci header.
1999-12-04 02:54:54 +00:00
eab9ce05b7
A PCI Revision ID of 0x02 is what ESS happens to be calling ES1946 Revision E.
1999-12-03 22:34:28 +00:00
229f631a84
regen
1999-12-01 15:08:17 +00:00
1657f687be
add Cyclades 4Y and 8Y
1999-12-01 15:07:44 +00:00
a7ee57948b
-support 3c905B-COMBO - somewhat preliminary: the chip has both an internal
...
MII PHY capable of NWAY (according to the Linux driver) and plain BNC/
transceiver connectors. The shared code can't handle this yet, so leave
out MII/NWAY for now.
-print out revision number from PCI config header, this has been useful to
identify buggy chips
1999-11-30 19:16:51 +00:00
9faac4111e
regen
1999-11-30 19:10:38 +00:00
b5db34e4d5
add 3c905B-COMBO
1999-11-30 19:09:54 +00:00
0c3ecf8e5e
Improve Ultra/66 support now that I've got some docs from Promise.
1999-11-28 20:05:18 +00:00
7b92ed07bd
Propagate the USB revision number to the usb driver.
1999-11-20 00:57:08 +00:00
7479d29f00
Make the ThunderLAN and VIA Rhine drivers use the common MII bit-bang module.
1999-11-19 18:27:18 +00:00
9ed17102f4
- Use the common MII bit-bang module.
...
- Add support other than 128-byte SROMs.
- Add support for the 21142/21143 MII.
1999-11-19 18:22:42 +00:00
ef8e85f177
Regen.
1999-11-17 00:09:48 +00:00
62058f9f6b
Add the SBLive! joystick device.
1999-11-17 00:09:17 +00:00
a525b9a12a
Commit patch kern/8778
...
Subject: NEC PCI modem support
1999-11-16 03:15:17 +00:00
7463c844a0
Make this file compile again; terminate the continuation line with backslash.
1999-11-16 02:13:02 +00:00
a49d3ecb33
Add a macro to generate a class code given class, subclass, and interface.
...
From UCHIYAMA Yasushi's PCI BIOS patches.
1999-11-15 23:41:10 +00:00
5527afff97
(pccbb_pci_callback): no point in reading the bus number register
...
twice
1999-11-15 16:19:03 +00:00
748b241afb
Export softc.
1999-11-13 13:40:28 +00:00
4bdf6bd731
Call mii_down() as appropriate.
1999-11-12 18:14:17 +00:00
1c37111492
Identification of DOMEX PCI-SCSI board, by Thilo Manske, PR 8772.
1999-11-12 12:03:32 +00:00
b4560adaf2
regen
1999-11-07 07:03:08 +00:00
7867af6cfb
back out rev 1.166:
...
(1) the list added isnt' complete and i'd call it incorrect. (There are
other devices with these names, where were omitted. I've never seen
the devices with these IDs, I _have_ seen the other devices that go
by these names.)
(2) the PR (8754) had not been updated to note that the problem was
fixed, and i'd preiously asked the submitter for more information and/or
a corrected list.
1999-11-07 06:59:46 +00:00
b2a56ee1b9
regen.
1999-11-06 13:50:02 +00:00
080ff79d14
Add vendor/product entry for Auravision VxP524 PCI Video Processor.
1999-11-06 13:48:29 +00:00
34e97b4c65
Regen.
1999-11-06 11:18:00 +00:00
3514a2e115
Add SIIG devices. Closes PR kern/8754 from Andreas Wrede <andreas@planix.com>
1999-11-06 11:17:30 +00:00
4a09180976
Don't pass rd/mult capability though a PCI-PCI bridge. The bridge would
...
have to break it up into mutliple rd/line's anyhow, so why bother letting
the device issue it in the first place.
1999-11-04 19:04:04 +00:00
110ac27449
Make sure devices are told they can use rd/line, rd/mult, and wr/inval.
1999-11-04 19:03:00 +00:00
c0b20561f7
regen
1999-11-04 16:18:41 +00:00
9df6f09e30
Add Aureal AU8820
1999-11-04 16:02:20 +00:00
fb580e3f6e
Regen.
1999-11-04 10:34:40 +00:00
1289659618
Add SBLive!
1999-11-04 10:34:03 +00:00
c8532c3ebe
regen
1999-11-04 09:39:17 +00:00
dbfcb792e1
add Xircom X3201-3 Fast Ethernet Controller
1999-11-04 09:38:38 +00:00
e3f20e8ff1
Use Memory Read Line and Memory Read Multiple on the 21140, 21140A,
...
21142, and 21143, if the PCI bus says its okay.
1999-11-04 01:20:55 +00:00
a4e1bde0b3
Print out if the read {line,multiple} and write/invalidate commands are
...
okay to use.
1999-11-04 01:03:34 +00:00
ca9b9a3b2e
Adapt to mii_phy_probe() change.
1999-11-04 00:24:00 +00:00
4f1f2c6398
Fix silly error that caused the secondary channel to be ignored if the primary
...
channel was disabled.
1999-11-03 14:54:07 +00:00
361b083d4c
Shorten some delay()s. From WITEK Wnuk <witek@atari.org>
1999-11-02 17:48:01 +00:00
b536890c88
Add a mixer control for the Master Volume Mute knob.
1999-11-02 12:11:42 +00:00
72a864f78c
Add the midibus attribute to the fms driver.
1999-11-02 11:58:06 +00:00
09c41837ce
Fix crash when both 1370 and 1371/1373 devices are configured.
...
Update documentation links.
XXX The initial volume of the 1371 mixers is set to 255. Should be ~200.
1999-11-02 05:40:59 +00:00
c8852145bc
Get fms MPU and OPL module inclusion right.
1999-11-02 00:29:20 +00:00
3c40153ea9
Fold some long lines and make it compile with the new auconv functions.
1999-11-01 23:26:58 +00:00
7c8206c662
Add a missing file for the fms driver.
1999-11-01 21:54:12 +00:00
8cd393778b
Regen.
1999-11-01 20:43:51 +00:00
684aa0605c
Add FM801 audio device driver. From Witold J. Wnuk ww181302@zodiac.mimuw.edu.pl
...
Closes PR kern/8729.
1999-11-01 20:43:12 +00:00
860ebb7a92
Make little endian and big endian version of all functions
...
that deal with 16 bit samples. Let the drivers decide which ones
to use.
1999-11-01 18:12:19 +00:00
8553661a5e
Maintainance the name of Ricoh PCI-CardBus bridges.
1999-11-01 08:58:45 +00:00
6346873ea6
Use the right attribute for attaching USB controllers.
...
From MAEKAWA Masahide <bishop@rr.iij4u.or.jp>
1999-10-30 17:03:30 +00:00
db05febdfa
Add enable/disable support and EEPROM size selection, prerequisites
...
for getting the cardbus fxp attachment to work.
Tested on the built-in 82559 in a VAIO Z505S.
From Johan Danielsson / PR8631; changed slightly to KNF.
1999-10-30 16:07:58 +00:00
3d0e8ae9dd
Make this file compile again by using the same names as in pcidevs.
1999-10-30 16:02:28 +00:00
a498fbea5f
Add midibus attribute for eap.
1999-10-30 14:11:16 +00:00
613db45d20
Add MIDI support.
...
Closes PR 8578.
1999-10-29 23:03:18 +00:00
471ab17680
Regen.
1999-10-29 21:31:30 +00:00
c707186f57
Add AHA-1480 (adaptec cardbus scsi)
1999-10-29 21:30:19 +00:00
65c3b4c4c7
Maintainance the name of Ricoh PCI-CardBus bridges.
1999-10-29 07:57:38 +00:00
9d820e6fab
Add some 21142/21143 goo.
1999-10-28 23:32:37 +00:00
44c603dd7b
Remove reference to loadable f/w.
1999-10-28 16:11:19 +00:00
38cae5303b
Remove htopci(). bus_space_write_4() takes care of necessary endian conversions.
1999-10-28 13:49:19 +00:00
8ecf3c7c3e
Add support for ES1371. From OpenBSD and Ezra Story <ezy@panix.com>.
1999-10-27 13:20:34 +00:00
0263d8db3d
Do not stop no matter when pci_mapreg_map fails to map bridge socket
...
registers. When it fails, reset Socket Base Address register and map
registers using rbus.
1999-10-27 00:48:36 +00:00
0021900156
Add a missing '\n' in the cmd0640 attach printfs.
1999-10-25 14:13:12 +00:00
5aa225ed2e
Disable legacy io port before the bridge is probed as a pcic on isa.
...
Comments ware changed to comply the KNF.
Add PCCBB_PCMCIA_16BITONLY to support TI PCI103X series.
1999-10-19 09:29:46 +00:00
cdad48e3b7
Oops- missed a MAXISPREQUEST sized thing- these are all gone now. It's amazing
...
this didn't eat me.
1999-10-17 02:40:26 +00:00
2b4cd26aa4
stylistic cleanups
1999-10-17 01:22:08 +00:00
c175d023d0
Comment out some debug settings.
...
Change attach printing so it looks more standard.
1999-10-15 10:59:56 +00:00
e5cc414836
add NetBSD ID tag.
1999-10-15 06:42:21 +00:00
4eee111127
This is the first check-in of CardBus driver. CardBus driver contains
...
CardBus bus stub, YENTA PCI-CardBus bridge (cbb), 3Com 3C575TX driver
(ex) and Intel fxp driver.
TODO:
o Conform to the KNF more strictly.
o Be unified with pcmcia code as much as possible.
o Add more drivers for CardBus card, such as APA-1480 or USB card.
The affected files are listed below.
sys/arch/i386/conf/files.i386
sys/arch/macppc/conf/files.macppc
sys/conf/files
sys/dev/ic/elinkxl.c
sys/dev/ic/elinkxlvar.h
sys/dev/ic/i82365.c
sys/dev/ic/i82365var.h
sys/dev/isa/i82365_isasubr.c
sys/dev/pci/files.pci
sys/dev/pcmcia/pcmcia.c
sys/dev/pcmcia/pcmciachip.h
The added files are listed below.
sys/arch/i386/conf/CARDBUS
sys/arch/i386/include/rbus_machdep.h
sys/arch/i386/i386/rbus_machdep.c
sys/arch/macppc/include/rbus_machdep.h
sys/arch/macppc/macppc/rbus_machdep.c
sys/dev/cardbus/if_ex_cardbus.c
sys/dev/cardbus/Makefile.cardbusdevs
sys/dev/cardbus/cardbus.c
sys/dev/cardbus/cardbus_map.c
sys/dev/cardbus/cardbusdevs
sys/dev/cardbus/cardbusdevs.h
sys/dev/cardbus/cardbusdevs_data.h
sys/dev/cardbus/cardbusvar.h
sys/dev/cardbus/cardslot.c
sys/dev/cardbus/cardslotvar.h
sys/dev/cardbus/devlist2h.awk
sys/dev/cardbus/files.cardbus
sys/dev/cardbus/if_fxp_cardbus.c
sys/dev/cardbus/pccardcis.h
sys/dev/cardbus/rbus.c
sys/dev/cardbus/rbus.h
sys/dev/pci/pccbb.c
sys/dev/pci/pccbbreg.h
sys/dev/pci/pccbbvar.h
1999-10-15 06:07:17 +00:00
83bb47c85a
F/W version no longer relevant. Only do WWN seed for FC cards.
...
Now we malloc xflist and dma maps in mailbox setup routines.
We also do the appropriate endian swizzling at the end of a dma
map routine.
1999-10-14 02:14:35 +00:00
358756a995
Add declaration for the Adaptec AIC-6915 64-bit 10/100 Ethernet interface.
...
Note: this is a placeholder right now; the driver should be ready in the
next few days.
1999-10-13 18:37:12 +00:00
b14b78dfc9
Deallocate resources (bus space and interrupts) when detaching from
...
the bus.
1999-10-12 11:21:24 +00:00
9d12a71473
Add support for `Adaptec AHA 2940UW Pro'.
...
Behaves like the `Adaptec AHA 2940UW'.
Device info: product id = 0x8778, Chip = AIC7880P.
1999-10-12 08:41:55 +00:00
2f3b72ae59
Regen.
1999-10-11 17:33:51 +00:00
5e63221d99
Add an entry for the Adaptec 2940UW Pro Scsi adapter.
1999-10-11 17:31:52 +00:00
c3703ecfdd
don't print using string pointer one off the end of the eso_rev2model
...
array. pointed out by Kouichi Hashikawa in PR#8601.
1999-10-10 18:52:03 +00:00
c3d5267629
Don't burst into flame when a QUEUE FULL message is received. Also,
...
do a gross hack which allows seemingly-broken quantum drives to function
with this driver. The gross hack is to disable tagged queueing completely
when QUEUE FULL is received. That costs performance on drives which
do tagged queueing properly and which return QUEUE FULL, but given the way
this driver works it's seems to be the only thing short of significant
recoding which will make it function with the quantum drives in question.
1999-10-08 20:43:45 +00:00
0b5c897fd0
1. include headers for NS support
...
2. pull in a fix from FreeBSD:
revision 1.18
date: 1999/09/17 18:04:14; author: wpaul; state: Exp; lines: +3 -3
Remember to account for ETHER_ALIGN when setting the maxmimum packet
length for mini receive ring. The max length was MHLEN, however the mbufs
are actually shortened to MHLEN - ETHER_ALIGN to force payload alignment.
1999-10-06 11:23:33 +00:00
a339b2839b
Have I mentioned how much I love this driver? Fix the code in the tagged
...
queueing support that decreases the number of openings on a device; it
previously assumed that a scsipi_link's `openings' were descreased as
commands were issued, which is not longer the case (`active' is increased).
1999-10-05 17:45:57 +00:00
120e8cac48
Fix a botch when updating for the SCSIPI changes.
1999-10-05 00:29:41 +00:00
63b8530b4e
Update for SCSPI changes.
1999-09-30 23:04:39 +00:00
30e63d853c
Define flags in pci_attach_args which indicate it's okay to use the
...
Memory Read Line, Memory Read Multiple, and Memory Write and Invalidate
PCI commands.
1999-09-30 20:30:06 +00:00
2492ffef4c
Changes to get the Lite-On/Macronix 82C115 working:
...
- 82C115 has a 128-bit multicast hash table, not 512-bit.
- Correct the way the MAC address is read from the SROM, after re-reading
the MX98715A Application Note.
Other semi-related changes:
- Differentiate between MX98715 and MX98715A.
- Improve the Macronix link-up/link-down detection.
1999-09-30 17:48:24 +00:00
e3398d3647
- Get a little closer on the Macronix chips. Still some more work to do.
...
- Add some basic support for the ADMtek AL981 clone (which, unfortunately,
I can't test until my sample boards arrive).
1999-09-29 18:52:19 +00:00
f6e42db75a
- Move initial reset code into dpt_readcfg()
...
- Bus specific front-end is now responsible for reading EATA configuration
- EATA configuration data is now saved in the softc
- Make synchronous writes work properly
- Don't ignore HBA timeouts in dpt_cmd()
- Prefix eata_cfg's members with `ec_', not `dc_'
1999-09-29 17:33:02 +00:00
1cb047331b
Regen.
1999-09-29 00:20:25 +00:00
33f02f24b7
- Add Sundance Technolgy vendor ID.
...
- Add Sundance Technolgy ST201 10/100 Ethernet product ID.
- Add D-Link DFE-550TX product ID (uses ST201 chip).
1999-09-29 00:19:51 +00:00
e2504d1efc
Regen.
1999-09-29 00:07:51 +00:00
8f22cca8ea
Add adaptec AIC-6915 10/100 Ethernet.
1999-09-29 00:07:15 +00:00
df12499646
Add code to take a device out of Power-Down state if it's in such a state,
...
and attempt to attach Macronix chips.
1999-09-28 23:12:23 +00:00
bb54953b63
Since the Audio 1 DMA controller implements the 24 low address bits only,
...
add the gross hack originally implemented by Charles Hannum in the SonicVibes
driver to force allocation of DMA memory for that channel through the Scatter-
Gather Map to get an address range that fits in.
The eso driver now works on Alphas except for DWLPX-based systems, whose owners
are not likely to desire audio or likely can afford slightly less cheap audio
hardware. :-)
1999-09-28 13:57:45 +00:00
f653cce944
Regen.
1999-09-27 23:46:56 +00:00
94367db635
s@SmartCache/Raid@SmartCache/SmartRAID@
1999-09-27 23:45:57 +00:00
a289fc5023
Add glue for 'dpt' driver.
1999-09-27 23:44:27 +00:00
48a0b6237a
A driver for DPT EATA SCSI adapters. dpt.c contains a brief TODO list.
1999-09-27 23:41:47 +00:00
6146ed7db8
add classes/subclasses new in PCI 2.2. Needs a bit of cleanup, but then,
...
so does everything involving configuration space headers and if i don't
get this out of my source tree i'll go insane.
1999-09-27 03:20:47 +00:00
2bc8340297
Add a quirk entry for the Asante 21140[A] boards that don't use the
...
ISV SROM format. For these boards, we provide the GPIO pin direction
info, a separate reset hook, and hard-wire them to MII-on-SIO.
Based on a patch submitted by Luoqi Chen <luoqi@chekov.watermarkgroup.com>.
1999-09-26 05:03:58 +00:00
4d4ddf363f
Some 21140[A] boards don't use the ISV SROM format (e.g. Asante boards),
...
but instead use the older DEC Address ROM format.
From a patch supplied by Luoqi Chen <luoqi@chekov.watermarkgroup.com>.
1999-09-26 04:43:45 +00:00
b76293b895
Add quirk entry support for the 21041 and 21140 chips. Initial quirks
...
for these: extract the spiffy DEC board names (e.g. DE500-AA).
1999-09-26 04:37:29 +00:00
4fa51ba8bd
Make tlp_read_srom() work on big-endian systems.
...
From a patch supplied by Luoqi Chen <luoqi@chekov.watermarkgroup.com>.
1999-09-26 03:39:01 +00:00
c999e3ca1a
Add support for the DECchip 21140[A]. This currently only works with
...
boards which use MII for media attachment.
ISV SROM format information lifted from Matt Thomas's `de' driver.
Thanks to Dave Sainty for experimenting w/ his 21140A MII boards, and
for supplying a fix to the MII bit-bang code (PR #8382 ).
1999-09-25 00:27:00 +00:00
d9abf5e332
Add Game Port definitions.
1999-09-23 11:50:19 +00:00
cef2689773
Oops, we do have to check ourselves whether a given value is valid within an
...
enumeration.
1999-09-23 11:46:12 +00:00
7460a0be93
Set sc_cfg3_fscsi for the AMD53C974 to match the change in ncr53c9x.c.
1999-09-22 03:32:00 +00:00
664d8da4f5
Add support for the DECchip 21041. This also adds some preliminary
...
support for the ISV SROM format used in the 2114{1,1A,2,3}. Note, like
the 21040, auto-sense is not yet supported for the 21041.
Add a "pre-init" hook, which will be used for the 2114x and PNIC (currently)
which allows chip-specific code to set up and write OPMODE before the
chip is reset. This is necessary in order for the chip's internal
pathways to get initialized properly for MII/SYM/PCS/SIA media attachments.
Thanks to Dave Sainty for the hint from the `de' driver that inspired the
pre-init hook.
1999-09-20 19:26:54 +00:00
6961f081e5
Fix packet reception in promiscuous mode: compare the Ethernet destination
...
address against our station address if it's not a multicast packet. Either
the Rhine manual lies about the phys/broadcast/multicast rxstatus bits,
or the Rhine chip is just broken.
Fixes a redirect storm problem reported by Laine Stump on current-users.
1999-09-20 17:40:58 +00:00
79f938f5f8
Fix a few buglets in the multi-port 21040 code. ZNYX ZX314 confirmed
...
working now.
1999-09-17 21:55:01 +00:00
7049e8eb1b
Add preliminary (untested) code for detaching the USB host controller
...
(needed for CardBus based controllers).
1999-09-15 10:25:30 +00:00
f23c7a31b4
Make sure 21040 chips are at least pass 2.0 and that 21140 chips are at
...
least pass 1.1.
1999-09-14 23:43:10 +00:00
70997fd3d5
Move the PCI device number to the base Tulip softc; it will be needed to
...
decode the SROM on 21041 and 2114x multi-port boards.
1999-09-14 23:33:04 +00:00
5c34356d4c
First crack at shared ROM/shared interrupts on 21040 multi-port boards,
...
plus quirk identification for non-multiple-port boards.
1999-09-14 22:25:48 +00:00
a6aa488db9
Don't do IO before we have set the tag and handle.
1999-09-14 09:29:05 +00:00
e2a320f925
Oops, fix Winbond regshift.
1999-09-14 05:59:53 +00:00
12c167b5ca
Change the semantics of `sc_regshift'; it is now the shift required to
...
make a CSR index number into a CSR offset. Introduce a couple of macros
to handle CSR name -> offset conversion.
1999-09-14 05:52:21 +00:00
10d4a4d5fe
And commit two files I forgot in the rearrangement for testing for
...
interrupt context.
1999-09-14 01:07:13 +00:00
a03bd733ca
- More PNIC NWAY stuff. Still more work to do, here.
...
- Fix the SROM checksum routine.
- Add code to parse the old DEC Address ROM SROM format.
- Rearrange the statchg routines a bit, to make them consistent with one
another.
- Add support for the DECchip 21040. XXX No support for media autosense
yet, and no support for any of the multi-port boards yet.
1999-09-14 00:55:38 +00:00
203f000d1a
Regen.
1999-09-11 06:27:36 +00:00
dfbe7449e4
Add ENI SpeedStream.
1999-09-11 06:27:25 +00:00
6a58ae2d93
Regen.
1999-09-10 19:56:51 +00:00
fb9d7d86ae
Add more TI CardBus bridges. Taken from the CardBus patches.
1999-09-10 19:55:54 +00:00
a10045109d
Add chip types for several more Tulip clones (ASIX, ADMtex, PNIC II, Davicom),
...
and match the Compex RL100-ATX; it uses the Winbond 89C840F (RL100-TX is
a Macronix 98713).
1999-09-08 22:29:46 +00:00
e0c4f8ff92
Regen.
1999-09-08 22:25:56 +00:00
dfdd1affb4
Add some more Tulip clones.
1999-09-08 22:25:19 +00:00
ab08b6b863
Update for Lite-On product ID change.
1999-09-08 21:42:44 +00:00
ab7310ed6e
Regen.
1999-09-08 21:39:54 +00:00
9bb30be866
Add Davicom Semiconductor vendor ID, and Davicom DM9102 10/100 Etherent
...
product ID (Yet Another Tulip Clone).
1999-09-08 21:39:24 +00:00
187510560e
Regen.
1999-09-08 21:34:33 +00:00
46e11c9fd8
LITEON_PNIC -> LITEON_82C168
1999-09-08 21:33:59 +00:00
e1766aacfa
Make sure not to use the io handle before it's been initialized.
1999-09-04 22:00:32 +00:00
6a2319b969
Byte swap the EEPROM words on the PNIC. From Stephen Ma.
1999-09-03 00:24:56 +00:00
533b6088cd
Make it compile.
1999-09-02 23:23:03 +00:00
9c10799ac4
Use the approximated sampling rate to compute the filter rate.
1999-09-02 17:26:15 +00:00
a6aa19699f
Don't assume that an -FX card has MII (because it doesn't).
1999-09-01 20:26:43 +00:00
480e8a1a1c
No longer requires mpuvar.h.
1999-09-01 18:03:10 +00:00
ce80d27933
Don't try to unmap unmapped space in case of failure in
...
pciide_mapregs_compat(). From OpenBSD.
1999-09-01 15:17:07 +00:00
7c34574b94
add "ti" - Alteon Gigabit Ethernet
1999-09-01 11:54:32 +00:00
45e5d743af
quick 'n dirty port of FreeBSD's Alteon Gigabit Ethernet driver.
...
todo:
-IPv6
-clean up jumbo buffer allocation - NetBSD provides an opaque argument
to the free function, thus doesn't need the hack done here
-deal correctly with the mapping of the shared memory
1999-09-01 11:47:46 +00:00
7eaa4e57fd
regen
1999-09-01 11:42:32 +00:00
enami