* Rearrange the speed mapping table and adjust the code so that the highest
rate can actually be used. Previously we ended up rounding up slightly
lower speeds and then losing because set_params couldn't set the mode
back to the current one.
* Allow 260 as a valid I/O address, since the SB1 can be jumpered to this.
* Change the MPU-401 code so it can be attached as a separate device.
(XXX Really, the SB code ought to just attach a subdevice itself.)
* Do not attach an OPL on the SB1. Writing to the OPL registers at
SB_base+0 on this card wedges my machine.
(XXX Should we access it at 388 instead? The Creative web site claims
that this board *does* have an OPL2, but I haven't played with this
extensively.)
* Allocate the SB DMA channels at open time, rather than attach time, so
that a single DRQ can be used for multiple cards (if only one is in use
at a given time).
(XXX Let me tell you why this is a horrible hack. If the ISA DMA code
tries to allocate a bounce buffer after boot time, it will generally fail,
because there is no contiguous memory below 16MB and the code to allocate
contiguous pages doesn't know how to move things around. Now, we
shouldn't ever be using bounce buffers here, because we use
isa_dmamem_alloc(). So we just turn off BUS_DMA_ALLOCNOW and we don't
actually try to. That's cool, and it even works, but isa_dmamem_alloc()
has the same problem. It just happens that we allocate the ring buffers
at boot time, and whenever we reallocate them (due to the buffer size
changing), we just deallocated the previous (contiguous) buffer, so we get
lucky. This is absolutely disgusting and needs to be fixed.)
* Improve the midisyn layer a little.
* Add a driver for the Yamaha OPL[23] FM synths.
The opl driver is not finished yet; it sounds pretty awful.
For some strange reason I cannot get any FM sound from my SB64 cards,
but a regular SB16 works fine.
Also, even on the SB1, we can leave the DMA controller in auto-initalize
mode and just send a command to the board for each block. This may help
prevent FIFO underruns.
the /dev/rmidiN devices, or with a sequencer interface via /dev/music.
So far the only supported MIDI device is the MPU401 port on SoundBlaster
(and only on SB on isapnp, since we do not have locators with multiple
values yet).
The changes is to allow some limited mixer manipulation through
the audio device (instead of the mixer device).
This rendered 4 methods in audio_hw_if unused so garbage collect these.
- Change the way attach and open works to allow multiple audio
devices.
- Split the mulaw.c file into two to avoid dragging in mulaw
convertsion when they are not needed. Add 16 bit alaw/mulaw tables.
- Change the way audio properties are gotten.
- Recognize more versions os SoundBlaster.
- It is now possible to handle devices that want "looping" DMA,
e.g. the SoundBlaster correctly. The WSS and SB drivers use this.
To do this several new methods were introduced in audio_hw_if.
- Different silence handling (forced by previous change).
- The audio driver can now be mmap()-ed, but due to problems in
the VM system only for writing for now.
- The OSS (Linux) audio emulation takes advantage of some of the
new features.
Set the encoding parameters slightly differently.
Remove the SW encoding/decodinf functions from this interface
and move them to the audio_parameter struct; this is both more efficient
and flexible.
- split softc size and match/attach out from cfdriver into
a new struct cfattach.
- new "attach" directive for files.*. May specify the name of
the cfattach structure, so that devices may be easily attached
to parents with different autoconfiguration semantics.
'flags 1' on the sb? kernel configuration file line (because it frobs a
noncontiguous IO port to configure the Jazz16 extensions).
Also, remove static sb_device structure and fill in user's buffer on
each request.
