fix 'cd' driver's NCD_SCSI bogosity (was using testing wrong macro!)
clean up in various ways:
* make common atapi_mode_{sense,select}() functions.
* put ATAPI data structures in more sensible headers, split up by
device type.
* include headers a bit more carefully.
* pass flags to attachment-specific cd functions, and use them.
* get rid of SCSI bits in scsipi_base.h's scsipi_make_xs(), move
them into the correct place in scsi_base.c.
* fix minor typo in struct name in scsipiconf.h (which was apparently
never used except in a #define later in the same file).
* use __attribute__ to force 4-byte alignment for xs command store,
so that architectures trying to bus_space_write_multi_N() (where
N > 1) that data to a controller won't lose.
* clean up a few comments in typos, and make a few #defines easier to
understand/maintain.
* rename cd_link.h to cdvar.h (via repository copy). This is exactly
what a 'var' file is supposed to be.
* Fix bug in wdc that would overflow ATAPI transfer length.
* Improve wdc probe code so that 'wdc' is probed in if present
even if there are no drives attached, and so that it works
properly even if the only device is an ATAPI slave.
* bus_space-ify.
* split the ISA attachment from the wdc driver, and remove
ISA dependencies from non-ISA files.
* claim that wd and wdc are now machine-independent (probably not
completely true, but mostly so; they at least work on arm32 and
i386).
* Various other minor fixups and cleanups, some of which were pointed
out by Kazuki Sakamoto.
now lives in dev/ic, wd now lives in dev/ata. there's now a 'ata'
interface attribute defined in conf/files, but wdc can't go there
yet because some ports still use private versions based on the old
ISA version.
- "out of resource" errors cause receive buffer chain corruption
- resets can confuse the interrupt handler
- multi-cast setup causes receive buffer chain corruption
- shared memory setup incomplete
* Enhance effiency by avoiding unnecessary shared memory access,
improved handling of receive frame & buffer descriptors, and
introducing an `asynchronous' option when issuing 82586 commands.
* Exclusively use offsets relative to the bus handle representing the shared
memory area to formulate accesses to the chip's data-structures. The
front-ends provide glue functions that cater to the chip's endian-
sensitivity, to perform the actual device access (note: single-byte
accesses are done here using `bus_space_{read,write}_1()').
This concludes the transformation into a bus-independent driver module.
* Abolish C structures to access chip data-structures; instead use macros
that take indices and offsets relative to the bus handle representing
the chip's resources.
* Include the old version of this file wholesale, until all drivers
have been updated to use the MI 82586 code.
- allow get/set of enums SUNAUDIO_SOURCE and SUNAUDIO_OUTPUT rather
than returning EINVAL
- add missing SUNAUDIO_MONITOR_CLASS case in query_devinfo
- convert SUNAUDIO_MONITOR case from a MIXER_CLASS to a MIXER_VALUE
like it is supposed to be
- the labels for outputs/record class were swapped: fix it
this patch allows "mixerctl" to work properly on a sparc
- Closing the audio device should stop recording.
- Manipulating the pause function could accidentally start playing or recording.
- AUDIO_FLUSH could accidentally start playing or recording.
- guard against synchronous I/O completion
- avoid race conditions
- use bgetvp/brelvp to properly maintain the vnode holdcount
and clean/dirty buffer lists.
the historical link? flags for media select)
XXX No pullup request for this. But if sysinst supports explicit media
XXX selection in 1.3, this should be in 1.3 as well.
does a "restore data pointers" when reselected after disconnecting in
the middle of a DMA transfer). The driver needs a different way to know
which script to continue the DMA transfer. The message-in for the "restore
data pointers" loses the original "resume" script, and the driver would
attempt to continue the DMA transfer at the beginning of the current DMA
chunk, rather than at the point the disconnect occured. The result was a
spurious console message, and a trashed filesystem.
clobbers my SMC. Now I can really use a generic kernel with my SMC @0x300.
This change has been tested on various machines with ne2000 and 3c509 baords.
XXX All these probes sould be reordered after the release, with invasive
XXX probes at the end.
to be reloaded every time it is checked. This avoids a condition where
it can be cached in a register in such a way that updates to the flags in
an interrupt handler to not be noticed, which in turn causes the process
doing the i/o to sleep forever. Bug report and suggested fix from
Hiroshi HORIMOTO <horimoto@cs-yuugao.cs.sist.ac.jp>, PR $4460.
nullbuf (used to pad packets < ETHER_MIN_SIZE) is used for all tl
interfaces. Allocates only once, and never deallocate it (as we can't say
if another instance of the driver is interface is using it).
i/o-mapped space to always be used), we discover that at least one
ThunderLAN interface can't read the EEPROM properly if memory-mapped
access is used. Kludge around this for now by "prefering" i/o space.
to look specifically at the address it was provided *only*, since the
scan isn't safe (it can stomp on cards that will be probed later, like
NE2000 clones).
- Do PCI space configuration like the other drivers. In particular,
don't _disable_ the space we're not using because some lame firmware
implementations might not reenable it on warm boot. Also, prefer
memory space always.
- Make match and info-gathering in attach table-driven.
- Rearrange things a bit to be a bit more visually pleasing during boot.
Also, fixup some #include problems.
- clean up debug code
- Don't check ATAPI signature when probing ATA drives, ATAPI devices were
detected before
- Reset controller after disks probes. The probe, with some combinations of
ATA/ATAPI device keep it in a mostly working, but strange state (with busy
led on)
- The WDCF_IRQ_WAIT flag is now cleared by wdc_ata_intr and wdc_atapi_intr
when appropriate (helps recover from failure conditions)
- In wdcunwedge, send ATAPI_SOFT_RESET to non-ata drives
(helps recover from failure conditions)
- in wdctimeout be a bit more verbose when we missed an interrupt
- Always Increment xfer->c_skip where it should be
- Set the ITSDONE flag when a polled command completed.
for 12-bit addresses. This causes PCMCIA cards mapped at 0x400 and higher
to not function properly. However, the range 0x300-0x3ff causes some
laptops (e.g. the NEC Versa 6030X) to hang if cards are mapped there.
So, after some experimentation, we compromise. If the probe discovers
a 12-bit address bus, don't trust it. Instead, use the range 0x330-0x3ff.
This has been shown to work on the laptops that the 0x300-0x3ff range is
known to fail on.
supports generic SMC91cxx-based ISA cards and the built-in SMC
Ethernet found in some laptop docking stations.
Thanks much to Andrew Gillham <gillhaa@ghost.whirlpool.com> for
making this work!
more robust in resource shortage situations, basically identical to
code I added to the "ahc" driver some time ago.
Thanks to Brad Spencer for the testing help.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
* Carrier detect (TS_CARR_ON) is based on the actual DCD bit, even if it's
being ignored.
* Set TS_WOPEN early on in zsopen().
* Don't disable interrupts on the console during close if we have DDB.
Inert changes:
* Don't handle ZS_HWFLAG_NO_DCD here; the frontend does it.
* Deprecate `register'.
* Use SET(), CLR(), and ISSET().
More performance changes:
* Rototill receive handling; use a backpressure mechanism to prevent livelock.
* Output silo/ibuf overflow warnings at most once per minute, from a callout.
* When we exhaust the current transmit run, turn off transmit interrupts in
zstty_txint(), so we're fairly sure we don't get another one.
* Make the ring buffer size and water marks patchable, and allocate the buffer
separately.
* Do the ttymalloc() at attach time.
* Reorganize the receive buffer so the status and data pair are next to each
other. This is slightly faster.
* Make sure we actually do turn off interrupts in comclose() if we have DDB
configured and it's not the console. (D'oh!!!!)
* When we exhaust the current transmit run, turn off transmit interrupts in
comintr(), so we're fairly sure we don't get another one.
* Nuke the silly lsrmap[] idea; it's slower in the normal case.
* Cache the l_rint pointer in the soft interrupt routine.
Supports changing media with ifconfig's "media" directive.
This splits the 3c503 functionality out of the ISA "ed" driver, much the
same way NE2000 support was split out.
control any more, and the speed of changing DTR isn't really an issue. Also,
the old code created a bug where zsparam() might have failed to set some
registers.
Change the interface to zs_hwiflow(); just have it use zst_rx_blocked.
Make zs_modem() a tiny bit faster.
Do RTS updates immediately; do not allow them to be held.
Stop output as fast as possible when DCD is deasserted.
Do *not* automatically drop DTR when DCD is deasserted.
Only check for rr0 bits that we care about (DTR and DCD).
Make sure we turn on DTR and/or RTS as appropriate during open.
Rearrange close sequence so the tty is flushed before turning off interrupts.
Deal with `softcar' and the console device by silently asserting CLOCAL and
|HUPCL, as in com driver.
Do *not* fiddle with DTR when changing the line speed.
Make sure we update the tty's carrier status when CLOCAL or MDMBUF is changed.
Only change rr1 when we actually need to turn on or off TIE.
intr_alloc_mask) into one place, comment them, and defopt them.
- Rename pcic_intr_alloc_mask to pcic_isa_intr_alloc_mask, since it's
an ISA-specific thing.
- When allocating/establishing the PCIC's interrupt (for card events),
do error checking, and pay attention to the intr_alloc_mask.
for the built-in SCSI on NEC Versa docking stations, and if a card
allocates that IRQ, it will never get interrupts. This caused the
default kernel to not work on these laptops, as IRQ 10 was often the
first free IRQ.
things happen if we are the console.
Restore to the prevoius value (not to hardwired 8N1) because this
could be set by the serial console initialization.
Closed PR kern/4373 (Dave Huang)
in the ISR (from the ISA "ed" driver's generic 8390 probe routine).
Also, add a big comment describing exactly what we're checking when
probing for the dp8390 (also lifted from the ISA "ed" driver).
The RST check should help weed-out non-matches before they get to the
fairly invasive memory check.
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
Also, fix the scb freelist fencepost, like the aha/bha/uha drivers.
should creation/initialization of a ecb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ecb what we can grab, and continue to hobble along.
should creation/initialization of a mscp fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one mscp what we can grab, and continue to hobble along.
Also, fix the mscp freelist fencepost error, similar to aha.c and bha.c
should creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
shoud creation/initialization of a ccb fail. Also, don't panic in
these situations. Instead, simply return an error condition and allow
the caller to deal with it. It may be the case that we were able to
create one ccb what we can grab, and continue to hobble along.
- add a type field to the isapnp_pin struct and set to IST_EDGE or
IST_LEVEL depending on the card configuration data.
- use the irq type field in all the drivers instead of hardcoding it.
Adjust the number of ccbs allocated during initialization.
Every ccb could potentially lock 64k of memory for dma buffers if bounce
buffers are used. Instead of BHA_CCB_MAX ccbs using 2MByte, only
sc_link.openings ccbs per device are allocated. Thus we now use only
256KByte per device present.
(hannken)
Fix a couple of errors in bha_create_ccbs():
- Don't ever let the number of CCBs be creater than BHA_CCB_MAX.
- Fix a fencepost that caused the last CCB allocated to never be put
on the freelist.
(thorpej)
change KEYSYM_HOLE to KEYSYM_NOP most places in those tables.
Map the `R' function keys with KEYSYM_FUNC_R instead of the
arrow key strings so that numlock indirection works.
- at end of attach, explicitely select an existing drive. This fixes hangs
some users reported (such as the one reported in port-i386/4247).
- Some atapi cdrom drives (e.g. Nec 24x) don't enables their registers before
a controller reset is issued. The controller probe routine is changed as
follow: issue a controller reset. If fail, test atapi signature on slave.
If fail, wait 5s and retry a reset. If the second reset fail, return(0).
If the first reset succeed, test presence of a master drive:
atapi signature, and if this fail RO/RW registers test. If no master, test
atapi signature on slave. If no slave, return 0.
"A sequence step of 0 after a select with ATN can be a selection
timeout, or it can also indicate the target did not respond with
a message out phase. The latter will occur on very old SCSI
devices which do not respond to the ATN signal and go directly to
the command phase".
* Make sure all uses of the data pointer are type-cast appropriately.
* Eliminate the super-user check in the KIOCSKEY case (back as it was).
* Return ENOTTY if the ioctl command code is unrecognized.
Instead, print a diagnostic and return. (Some drivers do this already.)
Also, normalize the diagnostic message, and fix some places where the
printfs were getting ugly.
- Work around a bug in the 82557 that causes the receiver to lock up
in certain conditions by kicking the multicast address filter if we
haven't heard anything come down the wire for some period of time.
- Fix a bug that could cause TxCB descriptor chains to cross page boundaries
on the Alpha.
- Remove some unneeded register masking.
- Fix a bug where too much data was copied from the config template, causing
memory corruption.
- Fix handing of if_timer (it was be cleared too early in some cases).
- Attempt to reduce the chances of receiver overrun by doubling the
number of receive DMA segments, and processing receive interrupts
before transmit interrupts.
- Remove a gratuitous assignment.
- Fix a bug where incoming packets were counted twice.
Dave Huang <khym@bga.com>, with added check for broken early versions
of the 16650, taken from the Linux driver.
This should be extended to use, for example, higher trigger levels for
the bigger 16650 FIFO, and its capability for using a smaller divisor
and thus higher speeds. But this patch is very useful for 16650 users
already.
Dave Huang <khym@bga.com>, with added check for broken early versions
of the 16650, taken from the Linux driver.
This should be extended to use, for example, higher trigger levels for
the bigger 16650 FIFO, and its capability for using a smaller divisor
and thus higher speeds. But this patch is very useful for 16650 users
already.
both 16bit id values found in card CIS and special value to indicate
that no value found in CIS. Use that special value for the card that
doesn't have id values. Test that value in ne2000_match().
options RND_COM
in your kernel config file (along with the
pseudo-device rnd
line) to enable this. If results are positive, I will make this enabled
by default.
splsoftclock() instead. This is done with an event queue of raw data,
and the entropy calculation etc. is done at splsoftclock().
o Use a private entropy pool rather than the global one defined in
rndpool.c. That global will probably go away, eventually.
The changes is to allow some limited mixer manipulation through
the audio device (instead of the mixer device).
This rendered 4 methods in audio_hw_if unused so garbage collect these.
> revision 1.1.2.6
> date: 1997/10/18 10:50:21; author: enami; state: Exp; lines: +2 -2
> In the macro ne2000_match(), use its argument `fct' instead of
> using pa->pf->number directly.
cd_scsibus_set_mode, to specifie the real len of "data" we need. These
functions were broken when scsi_cd_write_params_page was added to
scsi_cd_pages, thus changing the len of scsi_cd_mode_data.
adapters, and provide media-selections and status to the parent.
This includes drivers for the Thunderland integrated PHY, and
National Semiconductor's DP83840A.
Note: The interface betweeen network controller and mii is not complete yet,
and will need some minors tweaks to support media auto-selection.
drochner