1ad2891b6d
Don't scrub the environment unless we are going to change it. This should
...
prevent crashes in applications which carefully and manually construct
a temporary environment and later restore the original environment
like Emacs 24.
Problem reported by Thomas Klausner on "pkgsrc-users" mailing list.
2013-09-09 10:21:28 +00:00
be79f6c038
Improvements from jmc@openbsd.
2013-09-09 09:02:25 +00:00
f743a71b8d
Whitespace.
2013-09-09 08:23:54 +00:00
47c1ea4ca3
Remove movw/movt due to linker problems.
...
Check for 0 divisor and __aeabi_idiv0 if needed (EABI && _LIBC only).
2013-09-09 07:33:54 +00:00
4e222a409b
s/__libc/_libc/
2013-09-09 00:34:10 +00:00
6c1cfa38a7
use IPv6 Documentation Prefix (2001:db8::/32) instead of unallocated
...
d000🅰️ :/32 prefix
2013-09-08 19:12:18 +00:00
a50628ca37
Add CUBIEBOARD
2013-09-08 16:34:06 +00:00
8017a004f0
Note the new driver for MPL115A2.
2013-09-08 16:04:21 +00:00
3b7f8b823b
Add mpl115a(4) man page to dist list.
2013-09-08 16:01:47 +00:00
0c3b693fd3
Add mpl115a(4) man page for the new MPL115A2 pressure sensor driver.
2013-09-08 15:57:39 +00:00
c7b0c56c96
Preliminary support for MPL115A2 pressure sensor. It works, but accurracy is
...
awful.
I should add presure as a new type of sensor to envsys at some point...
2013-09-08 14:59:42 +00:00
4640275d2a
revert making smc91cxx_idstrs static, it's referenced from
...
sys/dev/isa/if_sm_isa.c
2013-09-08 14:27:39 +00:00
6fa7c3413b
Fix handling of NAME aliases in /etc/fstab.
2013-09-08 13:26:05 +00:00
0e3a78e197
Support using hwdiv instructions if those are available.
...
But only for EABI.
2013-09-08 13:24:16 +00:00
66ad0cf771
detect whether hw divide is present.
2013-09-08 13:15:53 +00:00
017bf683aa
defparam ATADEBUG_MASK
2013-09-08 12:51:14 +00:00
98efa985ed
Detect presence of hardware divide.
2013-09-08 12:11:56 +00:00
1529b1223b
Set the ACHI port mask since the h/w is broken.
2013-09-08 11:47:50 +00:00
2bf7a125b9
Allow the attachment to override ahci_ports.
...
Keep ACHI_PI cached in the softc.
2013-09-08 11:47:16 +00:00
1efbdaa7a9
If there is only 1 port, don't say "1 ports".
...
Add a debug printf after reading the active ports.
2013-09-08 11:19:47 +00:00
58c506be7c
correct a typo in the reg name polled while waiting for phy calibration
2013-09-08 10:43:51 +00:00
36ad2e17e8
Use correct offset for PLL6 register.
2013-09-08 10:32:56 +00:00
dc76b0b003
Add defaults for pkg_info and pkg_admin variables in case pkgpath.conf
...
is not installed.
2013-09-08 08:19:40 +00:00
c03ab98a67
Add sc->sc_bus.use_polling || to a couple of KASSERTs
...
PR/46826
2013-09-08 06:37:23 +00:00
15344de734
Fool isatty() into thinking we're a tty.
2013-09-08 04:37:17 +00:00
1730fa1769
Fix size of EHCI register space.
2013-09-08 04:10:23 +00:00
45d2ed72c1
Improve phy_init a little. Still doesn't work.
2013-09-08 04:07:45 +00:00
7ff2146a83
Rename awinfe to awe and awinge to awge.
...
Allow properties in awinio0 to disable devices.
Use such a property to disable probing of gige.
2013-09-08 04:06:44 +00:00
10b245faf0
Remove extra debug message.
2013-09-08 03:17:02 +00:00
40fad00f75
Add more nand #define's
2013-09-08 01:29:42 +00:00
79e6364f42
Move interrupts back to IPL_USB
2013-09-08 01:01:33 +00:00
33ff832239
Make sure to actual push the configuration of the GPIO to its registers.
...
With this change, USB now works.
2013-09-08 00:55:25 +00:00
0e738d35fd
Add mii support and some initialization.
2013-09-08 00:05:27 +00:00
b4057f5a8c
Add some comments
2013-09-08 00:04:33 +00:00
2aea4d4a26
Add mii attr to ethernet devices
2013-09-08 00:03:59 +00:00
febe4991a1
Add rlphy
2013-09-08 00:03:40 +00:00
b3d80f01ed
correct a typo in awin_gpio_pin_ctl that would have prevented configuring output pins
2013-09-07 23:47:33 +00:00
3b639577a4
Add a machdep.hwdiv_present sysctl (cortex A7 and A15 have hwdiv instructions)
2013-09-07 23:10:02 +00:00
21dbc4bb59
Reenable OHCI
2013-09-07 22:52:12 +00:00
5c28d99f8a
Simplify USB initialization.
2013-09-07 22:51:41 +00:00
d34a5755d1
start adding NFC registers
...
fix AWIN_AHB_GATING0_USB_OHCI0
2013-09-07 22:51:03 +00:00
e6c711a47f
add KASSERT to make sure softints are not NULL
2013-09-07 19:53:24 +00:00
5df3d4b64c
Add more initialization code for AHCI and USB.
...
Alas, neither still is coming up.
2013-09-07 19:48:57 +00:00
c5a9cb82c0
Finish off GPIO handler. Add hook for other driver to access a named gpio.
...
Add two input gpio's for usb0.
2013-09-07 19:47:28 +00:00
18ec38ea7c
switch to ELF naming for local labels.
2013-09-07 19:06:29 +00:00
c2a70ce464
apply changes from Robert Sprowson in PR 47765 and PR 47788:
...
- make sure we wait long enough after resetting the chip.
- add the necessary delay after changing the FIFO pointer.
- add a missing interrupt ACK.
- fix padding of short and odd-length packets.
and a few more changes from me:
- do 2-byte writes in most places even if SMC91CXX_NO_BYTE_WRITE
is not defined. the only ones still conditionalized are
writing to the interrupt ack/mask registers.
- the only big-endian front-end of this driver (on mac68k) uses
a bus_space that does all the byte-swapping in that layer,
so remove the explicit byte-swapping in the MI part.
tested on mac68k.
2013-09-07 18:55:29 +00:00
fbf90abc10
fix -Wuninitialized
2013-09-07 18:17:35 +00:00
28fc97ca89
Add an initial console device and open fd's 0/1/2 for initproc. This is
...
again useful in standalone-type environments such as Xen, where all
printf/etc calls go through the rump kernel.
2013-09-07 17:58:00 +00:00
45d149c466
Add forgotten xsh device.
2013-09-07 17:23:55 +00:00
b8a293f0ef
Some lock comments.
2013-09-07 16:47:23 +00:00
tron