Hide structure definitions and add explicit API instead, to keep an
eye on the scope of the shared fields.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-10-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Currently, block_copy operation lock the whole requested region. But
there is no reason to lock clusters, which are already copied, it will
disturb other parallel block_copy requests for no reason.
Let's instead do the following:
Lock only sub-region, which we are going to operate on. Then, after
copying all dirty sub-regions, we should wait for intersecting
requests block-copy, if they failed, we should retry these new dirty
clusters.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200311103004.7649-9-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
offset/bytes pair is more usual naming in block layer, let's use it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-8-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
We have a lot of "chunk_end - start" invocations, let's switch to
bytes/cur_bytes scheme instead.
While being here, improve check on block_copy_do_copy parameters to not
overflow when calculating nbytes and use int64_t for bytes in
block_copy for consistency.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-7-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split find_conflicting_inflight_req to be used separately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-6-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Use bdrv_block_status_above to chose effective chunk size and to handle
zeroes effectively.
This substitutes checking for just being allocated or not, and drops
old code path for it. Assistance by backup job is dropped too, as
caching block-status information is more difficult than just caching
is-allocated information in our dirty bitmap, and backup job is not
good place for this caching anyway.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-5-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
In block_copy_do_copy we fallback to read+write if copy_range failed.
In this case copy_size is larger than defined for buffered IO, and
there is corresponding commit. Still, backup copies data cluster by
cluster, and most of requests are limited to one cluster anyway, so the
only source of this one bad-limited request is copy-before-write
operation.
Further patch will move backup to use block_copy directly, than for
cases where copy_range is not supported, first request will be
oversized in each backup. It's not good, let's change it now.
Fix is simple: just limit first copy_range request like buffer-based
request. If it succeed, set larger copy_range limit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200311103004.7649-4-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Assume we have two regions, A and B, and region B is in-flight now,
region A is not yet touched, but it is unallocated and should be
skipped.
Correspondingly, as progress we have
total = A + B
current = 0
If we reset unallocated region A and call progress_reset_callback,
it will calculate 0 bytes dirty in the bitmap and call
job_progress_set_remaining, which will set
total = current + 0 = 0 + 0 = 0
So, B bytes are actually removed from total accounting. When job
finishes we'll have
total = 0
current = B
, which doesn't sound good.
This is because we didn't considered in-flight bytes, actually when
calculating remaining, we should have set (in_flight + dirty_bytes)
as remaining, not only dirty_bytes.
To fix it, let's refactor progress calculation, moving it to block-copy
itself instead of fixing callback. And, of course, track in_flight
bytes count.
We still have to keep one callback, to maintain backup job bytes_read
calculation, but it will go on soon, when we turn the whole backup
process into one block_copy call.
Cc: qemu-stable@nongnu.org
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Message-Id: <20200311103004.7649-3-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
On success path we return what inflate() returns instead of 0. And it
most probably works for Z_STREAM_END as it is positive, but is
definitely broken for Z_BUF_ERROR.
While being here, switch to errno return code, to be closer to
qcow2_compress API (and usual expectations).
Revert condition in if to be more positive. Drop dead initialization of
ret.
Cc: qemu-stable@nongnu.org # v4.0
Fixes: 341926ab83
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200302150930.16218-1-vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
'crypto_opts' forgot to free in qcow2_close(), this patch fix the bellow leak stack:
Direct leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f0edd81f970 in __interceptor_calloc (/lib64/libasan.so.5+0xef970)
#1 0x7f0edc6d149d in g_malloc0 (/lib64/libglib-2.0.so.0+0x5249d)
#2 0x55d7eaede63d in qobject_input_start_struct /mnt/sdb/qemu-new/qemu_test/qemu/qapi/qobject-input-visitor.c:295
#3 0x55d7eaed78b8 in visit_start_struct /mnt/sdb/qemu-new/qemu_test/qemu/qapi/qapi-visit-core.c:49
#4 0x55d7eaf5140b in visit_type_QCryptoBlockOpenOptions qapi/qapi-visit-crypto.c:290
#5 0x55d7eae43af3 in block_crypto_open_opts_init /mnt/sdb/qemu-new/qemu_test/qemu/block/crypto.c:163
#6 0x55d7eacd2924 in qcow2_update_options_prepare /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1148
#7 0x55d7eacd33f7 in qcow2_update_options /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1232
#8 0x55d7eacd9680 in qcow2_do_open /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1512
#9 0x55d7eacdc55e in qcow2_open_entry /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1792
#10 0x55d7eacdc8fe in qcow2_open /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:1819
#11 0x55d7eac3742d in bdrv_open_driver /mnt/sdb/qemu-new/qemu_test/qemu/block.c:1317
#12 0x55d7eac3e990 in bdrv_open_common /mnt/sdb/qemu-new/qemu_test/qemu/block.c:1575
#13 0x55d7eac4442c in bdrv_open_inherit /mnt/sdb/qemu-new/qemu_test/qemu/block.c:3126
#14 0x55d7eac45c3f in bdrv_open /mnt/sdb/qemu-new/qemu_test/qemu/block.c:3219
#15 0x55d7ead8e8a4 in blk_new_open /mnt/sdb/qemu-new/qemu_test/qemu/block/block-backend.c:397
#16 0x55d7eacde74c in qcow2_co_create /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:3534
#17 0x55d7eacdfa6d in qcow2_co_create_opts /mnt/sdb/qemu-new/qemu_test/qemu/block/qcow2.c:3668
#18 0x55d7eac1c678 in bdrv_create_co_entry /mnt/sdb/qemu-new/qemu_test/qemu/block.c:485
#19 0x55d7eb0024d2 in coroutine_trampoline /mnt/sdb/qemu-new/qemu_test/qemu/util/coroutine-ucontext.c:115
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200227012950.12256-2-pannengyuan@huawei.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
RFC 7230 section 3.2 indicates that HTTP header field names are case
insensitive.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20200224101310.101169-3-david.edmondson@oracle.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
RFC 7230 section 3.2 indicates that whitespace is permitted between
the field name and field value and after the field value.
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20200224101310.101169-2-david.edmondson@oracle.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add qemu-img measure support in the "luks" block driver.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200221112522.1497712-3-stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The qcow2 .bdrv_measure() code calculates the crypto payload offset.
This logic really belongs in crypto/block.c where it can be reused by
other image formats.
The "luks" block driver will need this same logic in order to implement
.bdrv_measure(), so extract the qcrypto_block_calculate_payload_offset()
function now.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200221112522.1497712-2-stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-12-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-11-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-10-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-9-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
hmp_snapshot_blkdev is from GPLv2 version of the hmp-cmds.c thus
have to change the licence to GPLv2
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-8-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-7-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Moved code was added after 2012-01-13, thus under GPLv2+
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-6-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixed commit message
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20200308092440.23564-5-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
These days device-hotplug.c only contains the hmp_drive_add
In the next patch, rest of hmp_drive* functions will be moved
there.
Also add block-hmp-cmds.h to contain prototypes of these
functions
License for block-hmp-cmds.h since it contains the code
moved from sysemu.h which lacks license and thus according
to LICENSE is under GPLv2+
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200308092440.23564-4-mlevitsk@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Clang static code analyzer show warning:
block/file-posix.c:891:9: warning: Value stored to 'op' is never read
op = RAW_PL_ABORT;
^ ~~~~~~~~~~~~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200302130715.29440-5-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Clang static code analyzer show warning:
block/stream.c:186:9: warning: Value stored to 'ret' is never read
ret = 0;
^ ~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200302130715.29440-3-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Starting from ceph Nautilus, RBD has support for namespaces, allowing
for finer grain ACLs on images inside a pool, and tenant isolation.
In the rbd cli tool documentation, the new image-spec and snap-spec are :
- [pool-name/[namespace-name/]]image-name
- [pool-name/[namespace-name/]]image-name@snap-name
When using an non namespace's enabled qemu, it complains about not
finding the image called namespace-name/image-name, thus we only need to
parse the image once again to find if there is a '/' in its name, and if
there is, use what is before it as the name of the namespace to later
pass it to rados_ioctx_set_namespace.
rados_ioctx_set_namespace if called with en empty string or a null
pointer as the namespace parameters pretty much does nothing, as it then
defaults to the default namespace.
The namespace is extracted inside qemu_rbd_parse_filename, stored in the
qdict, and used in qemu_rbd_connect to make it work with both qemu-img,
and qemu itself.
Signed-off-by: Florian Florensa <fflorensa@online.net>
Message-Id: <20200110111513.321728-2-fflorensa@online.net>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds a --blockdev option to the storage daemon that works the same
as the -blockdev option of the system emulator.
In order to be able to link with blockdev.o, we also need to change
stream.o from common-obj to block-obj, which is where all other block
jobs already are.
In contrast to the system emulator, qemu-storage-daemon options will be
processed in the order they are given. The user needs to take care to
refer to other objects only after defining them.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200224143008.13362-7-kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These commands make only sense for system emulators and their
implementations call functions that don't exist in tools (e.g. to
resolve qdev IDs). Move them out so that blockdev.c can be linked to
qemu-storage-daemon.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200224143008.13362-4-kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bitmap code requires writing the 'file' child when the qcow2 driver
is reopened in read-write mode.
If the 'file' child is being reopened due to a permissions change, the
modification is commited yet when qcow2_reopen_commit is called. This
means that any attempt to write the 'file' child will end with EBADFD
as the original fd was already closed.
Moving bitmap reopening to the new callback which is called after
permission modifications are commited fixes this as the file descriptor
will be replaced with the correct one.
The above problem manifests itself when reopening 'qcow2' format layer
which uses a 'file-posix' file child which was opened with the
'auto-read-only' property set.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Message-Id: <db118dbafe1955afbc0a18d3dd220931074ce349.1582893284.git.pkrempa@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
handle_alloc() reuses preallocated zero clusters. If anything goes
wrong during the data write, we do not change their L2 entry, so we
must not let qcow2_alloc_cluster_abort() free them.
Fixes: 8b24cd1415
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200225143130.111267-2-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
After failover the Secondary side of replication shouldn't change state, because
it now functions as our primary disk.
In replication_start, replication_do_checkpoint, replication_stop, ignore
the request if current state is BLOCK_REPLICATION_DONE (sucessful failover) or
BLOCK_REPLICATION_FAILOVER (failover in progres i.e. currently merging active
and hidden images into the base image).
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Zhang Chen <chen.zhang@intel.com>
Acked-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
In currently implementation there will be a memory leak when
nbd_client_connect() returns error status. Here is an easy way to
reproduce:
1. run qemu-iotests as follow and check the result with asan:
./check -raw 143
Following is the asan output backtrack:
Direct leak of 40 byte(s) in 1 object(s) allocated from:
#0 0x7f629688a560 in calloc (/usr/lib64/libasan.so.3+0xc7560)
#1 0x7f6295e7e015 in g_malloc0 (/usr/lib64/libglib-2.0.so.0+0x50015)
#2 0x56281dab4642 in qobject_input_start_struct /mnt/sdb/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:295
#3 0x56281dab1a04 in visit_start_struct /mnt/sdb/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:49
#4 0x56281dad1827 in visit_type_SocketAddress qapi/qapi-visit-sockets.c:386
#5 0x56281da8062f in nbd_config /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1716
#6 0x56281da8062f in nbd_process_options /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1829
#7 0x56281da8062f in nbd_open /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1873
Direct leak of 15 byte(s) in 1 object(s) allocated from:
#0 0x7f629688a3a0 in malloc (/usr/lib64/libasan.so.3+0xc73a0)
#1 0x7f6295e7dfbd in g_malloc (/usr/lib64/libglib-2.0.so.0+0x4ffbd)
#2 0x7f6295e96ace in g_strdup (/usr/lib64/libglib-2.0.so.0+0x68ace)
#3 0x56281da804ac in nbd_process_options /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1834
#4 0x56281da804ac in nbd_open /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1873
Indirect leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f629688a3a0 in malloc (/usr/lib64/libasan.so.3+0xc73a0)
#1 0x7f6295e7dfbd in g_malloc (/usr/lib64/libglib-2.0.so.0+0x4ffbd)
#2 0x7f6295e96ace in g_strdup (/usr/lib64/libglib-2.0.so.0+0x68ace)
#3 0x56281dab41a3 in qobject_input_type_str_keyval /mnt/sdb/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:536
#4 0x56281dab2ee9 in visit_type_str /mnt/sdb/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:297
#5 0x56281dad0fa1 in visit_type_UnixSocketAddress_members qapi/qapi-visit-sockets.c:141
#6 0x56281dad17b6 in visit_type_SocketAddress_members qapi/qapi-visit-sockets.c:366
#7 0x56281dad186a in visit_type_SocketAddress qapi/qapi-visit-sockets.c:393
#8 0x56281da8062f in nbd_config /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1716
#9 0x56281da8062f in nbd_process_options /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1829
#10 0x56281da8062f in nbd_open /mnt/sdb/qemu-4.2.0-rc0/block/nbd.c:1873
Fixes: 8f071c9db5
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Cc: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <1575517528-44312-3-git-send-email-pannengyuan@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The BDRVNBDState cleanup code is common in two places, add
nbd_clear_bdrvstate() function to do these cleanups.
Suggested-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <1575517528-44312-2-git-send-email-pannengyuan@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: fix compilation error and commit message]
Signed-off-by: Eric Blake <eblake@redhat.com>
The NBD URI specification [1] states that only one leading slash at
the beginning of the URI path component is stripped, not all such
slashes. This becomes important to a patch I just proposed to nbdkit
[2], which would allow the exportname to select a file embedded within
an ext2 image: ext2fs demands an absolute pathname beginning with '/',
and because qemu was inadvertantly stripping it, my nbdkit patch had
to work around the behavior.
[1] https://github.com/NetworkBlockDevice/nbd/blob/master/doc/uri.md
[2] https://www.redhat.com/archives/libguestfs/2020-February/msg00109.html
Note that the qemu bug only affects handling of URIs such as
nbd://host:port//abs/path (where '/abs/path' should be the export
name); it is still possible to use --image-opts and pass the desired
export name with a leading slash directly through JSON even without
this patch.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200212023101.1162686-1-eblake@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
When printing the snapshot list (e.g. with qemu-img snapshot -l), the VM
size field is only seven characters wide. As of de38b5005e, this is
not necessarily sufficient: We generally print three digits, and this
may require a decimal point. Also, the unit field grew from something
as plain as "M" to " MiB". This means that number and unit may take up
eight characters in total; but we also want spaces in front.
Considering previously the maximum width was four characters and the
field width was chosen to be three characters wider, let us adjust the
field width to be eleven now.
Fixes: de38b5005e
Buglink: https://bugs.launchpad.net/qemu/+bug/1859989
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200117105859.241818-2-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The generic fallback implementation effectively does the same.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200122164532.178040-5-mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The generic fallback implementation effectively does the same.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200122164532.178040-4-mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When nbd_close() is called from a coroutine, the connection_co never
gets to run, and thus nbd_teardown_connection() hangs.
This is because aio_co_enter() only puts the connection_co into the main
coroutine's wake-up queue, so this main coroutine needs to yield and
wait for connection_co to terminate.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200122164532.178040-2-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
backup-top "supports" write-unchanged, by skipping CBW operation in
backup_top_co_pwritev. But it forgets to do the same in
backup_top_co_pwrite_zeroes, as well as declare support for
BDRV_REQ_WRITE_UNCHANGED.
Fix this, and, while being here, declare also support for flags
supported by source child.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200207161231.32707-1-vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When initializing the LUKS header the size with default encryption
parameters will currently be 2068480 bytes. This is rounded up to
a multiple of the cluster size, 2081792, with 64k sectors. If the
end of the header is not the same as the end of the cluster we fill
the extra space with zeros. This was forgetting that not even the
space allocated for the header will be fully initialized, as we
only write key material for the first key slot. The space left
for the other 7 slots is never written to.
An optimization to the ref count checking code:
commit a5fff8d4b4 (refs/bisect/bad)
Author: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Date: Wed Feb 27 16:14:30 2019 +0300
qcow2-refcount: avoid eating RAM
made the assumption that every cluster which was allocated would
have at least some data written to it. This was violated by way
the LUKS header is only partially written, with much space simply
reserved for future use.
Depending on the cluster size this problem was masked by the
logic which wrote zeros between the end of the LUKS header and
the end of the cluster.
$ qemu-img create --object secret,id=cluster_encrypt0,data=123456 \
-f qcow2 -o cluster_size=2k,encrypt.iter-time=1,\
encrypt.format=luks,encrypt.key-secret=cluster_encrypt0 \
cluster_size_check.qcow2 100M
Formatting 'cluster_size_check.qcow2', fmt=qcow2 size=104857600
encrypt.format=luks encrypt.key-secret=cluster_encrypt0
encrypt.iter-time=1 cluster_size=2048 lazy_refcounts=off refcount_bits=16
$ qemu-img check --object secret,id=cluster_encrypt0,data=redhat \
'json:{"driver": "qcow2", "encrypt.format": "luks", \
"encrypt.key-secret": "cluster_encrypt0", \
"file.driver": "file", "file.filename": "cluster_size_check.qcow2"}'
ERROR: counting reference for region exceeding the end of the file by one cluster or more: offset 0x2000 size 0x1f9000
Leaked cluster 4 refcount=1 reference=0
...snip...
Leaked cluster 130 refcount=1 reference=0
1 errors were found on the image.
Data may be corrupted, or further writes to the image may corrupt it.
127 leaked clusters were found on the image.
This means waste of disk space, but no harm to data.
Image end offset: 268288
The problem only exists when the disk image is entirely empty. Writing
data to the disk image payload will solve the problem by causing the
end of the file to be extended further.
The change fixes it by ensuring that the entire allocated LUKS header
region is fully initialized with zeros. The qemu-img check will still
fail for any pre-existing disk images created prior to this change,
unless at least 1 byte of the payload is written to.
Fully writing zeros to the entire LUKS header is a good idea regardless
as it ensures that space has been allocated on the host filesystem (or
whatever block storage backend is used).
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20200207135520.2669430-1-berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When a management application manages node names there's no reason to
recurse into backing images in the output of query-named-block-nodes.
Add a parameter to the command which will return just the top level
structs.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Message-Id: <4470f8c779abc404dcf65e375db195cd91a80651.1579509782.git.pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[mreitz: Fixed coding style]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Quorum is not a filter, for example because it cannot guarantee which of
its children will serve the next request. Thus, any of its children may
differ from the data visible to quorum's parents.
We have other filters with multiple children, but they differ in this
aspect:
- blkverify quits the whole qemu process if its children differ. As
such, we can always skip it when we want to skip it (as a filter node)
by going to any of its children. Both have the same data.
- replication generally serves requests from bs->file, so this is its
only actually filtered child.
- Block job filters currently only have one child, but they will
probably get more children in the future. Still, they will always
have only one actually filtered child.
Having "filters" as a dedicated node category only makes sense if you
can skip them by going to a one fixed child that always shows the same
data as the filter node. Quorum cannot fulfill this, so it is not a
filter.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-13-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There is no guarantee that we can still replace the node we want to
replace at the end of the mirror job. Double-check by calling
bdrv_recurse_can_replace().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-12-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It no longer has any users.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-11-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-8-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Quorum cannot share WRITE or RESIZE on its children. Presumably, it
only does so because as a filter, it seemed intuitively correct to point
its .bdrv_child_perm to bdrv_filter_default_perm().
However, it is not really a filter, and bdrv_filter_default_perm() does
not work for it, so we have to provide a custom .bdrv_child_perm
implementation.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200218103454.296704-6-mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fixes: 6663a0a337
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200218094402.26625-5-philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
block_job_error_action() needs to know if reading from the top node or
writing to the base node failed so that it can set the right 'operation'
in the BLOCK_JOB_ERROR QMP event.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-6-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
commit_populate() is a very short function and only called in a single
place. Its return value doesn't tell us whether an error happened while
reading or writing, which would be necessary for sending the right data
in the BLOCK_JOB_ERROR QMP event.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-5-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The block_job_error_action() error call in the commit job gives the
on_err and is_read arguments in the wrong order. Fix this.
(Of course, hard-coded is_read = false is wrong, too, but that's a
separate problem for a separate patch.)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-4-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The bytes_written variable is only ever written to, it serves no
purpose. This has actually been the case since the commit job was first
introduced in commit 747ff60263.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200214200812.28180-3-kwolf@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Fix warning reported by Clang static code analyzer:
CC block/qcow2-bitmap.o
block/qcow2-bitmap.c:650:5: warning: Value stored to 'ret' is never read
ret = -EINVAL;
^ ~~~~~~~
Fixes: 88ddffae8
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200215161557.4077-2-philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
For external data file, cluster allocations return an offset in the data
file and are not refcounted. In this case, there is nothing to do for
qcow2_alloc_cluster_abort(). Freeing the same offset in the qcow2 file
is wrong and causes crashes in the better case or image corruption in
the worse case.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200211094900.17315-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the case that update_refcount() frees a refcount block, it evicts it
from the metadata cache. Before doing so, however, it returns the
currently used refcount block to the cache because it might be the same.
Returning the refcount block early means that we need to reset
old_table_index so that we reload the refcount block in the next
iteration if it is actually still in use.
Fixes: f71c08ea8e
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200211094900.17315-2-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before this commit, BDRVVVFATState.qcow is unrefed in write_target_close
on closing backing bdrv of vvfat. However, qcow bdrv is opend as a child
of vvfat in enable_write_target() so it will be also unrefed on closing
vvfat itself. This causes use-after-free of qcow on freeing vvfat which
has backing bdrv and qcow bdrv as children in this order because
bdrv_close(vvfat) tries to free qcow bdrv after freeing backing bdrv
as QLIST_FOREACH_SAFE() loop keeps next pointer, but BdrvChild of qcow
is already freed in bdrv_close(backing bdrv).
Signed-off-by: Hikaru Nishida <hikarupsp@gmail.com>
Message-Id: <20200209175156.85748-1-hikarupsp@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I/O requests to encrypted media should be aligned to the sector size
used by the underlying encryption method, not to BDRV_SECTOR_SIZE.
Fortunately this doesn't break anything at the moment because
both existing QCRYPTO_BLOCK_*_SECTOR_SIZE have the same value as
BDRV_SECTOR_SIZE.
The checks in qcow2_co_preadv_encrypted() are also unnecessary because
they are repeated immediately afterwards in qcow2_co_encdec().
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20200213171646.15876-1-berto@igalia.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
mirror_wait_for_free_in_flight_slot() just picks a random operation to
wait for. However, when mirror_co_read() waits for free slots, its
MirrorOp is already in s->ops_in_flight, so if not enough slots are
immediately available, an operation can end up waiting for itself to
complete, which results in a hang.
Fix this by passing the current MirrorOp and skipping this operation
when picking an operation to wait for.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1794692
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
If a coroutine is launched, but the coroutine pointer isn't stored
anywhere, debugging any problems inside the coroutine is quite hard.
Let's store the coroutine pointer of a mirror operation in MirrorOp to
have it available in the debugger.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Commit 7a3f542fbd "block/io: refactor padding" occasionally dropped
aligning for zero-length request: bdrv_init_padding() blindly return
false if bytes == 0, like there is nothing to align.
This leads the following command to crash:
./qemu-io --image-opts -c 'write 1 0' \
driver=blkdebug,align=512,image.driver=null-co,image.size=512
>> qemu-io: block/io.c:1955: bdrv_aligned_pwritev: Assertion
`(offset & (align - 1)) == 0' failed.
>> Aborted (core dumped)
Prior to 7a3f542fbd we does aligning of such zero requests. Instead of
recovering this behavior let's just do nothing on such requests as it
is useless.
Note that driver may have special meaning of zero-length reqeusts, like
qcow2_co_pwritev_compressed_part, so we can't skip any zero-length
operation. But for unaligned ones, we can't pass it to driver anyway.
This commit also fixes crash in iotest 80 running with -nocache:
./check -nocache -qcow2 80
which crashes on same assertion due to trying to read empty extra data
in qcow2_do_read_snapshots().
Cc: qemu-stable@nongnu.org # v4.2
Fixes: 7a3f542fbd
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20200206164245.17781-1-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We can't access top after call bdrv_backup_top_drop, as it is already
freed at this time.
Also, no needs to unref target child by hand, it will be unrefed on
bdrv_close() automatically.
So, just do bdrv_backup_top_drop if append succeed and one bdrv_unref
otherwise.
Note, that in !appended case bdrv_unref(top) moved into drained section
on source. It doesn't really matter, but just for code simplicity.
Fixes: 7df7868b96
Cc: qemu-stable@nongnu.org # v4.2.0
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20200121142802.21467-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qemu-img's convert_co_copy_range() operates at the sector level and
block_copy() operates at the cluster level so this condition is always
true, but it is not necessary to restrict this here, so let's leave it
to the driver implementation return an error if there is any.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: a4264aaee656910c84161a2965f7a501437379ca.1579374329.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When updating an L1 entry the qcow2 driver writes a (512-byte) sector
worth of data to avoid a read-modify-write cycle. Instead of always
writing 512 bytes we should follow the alignment requirements of the
storage backend.
(the only exception is when the alignment is larger than the cluster
size because then we could be overwriting data after the L1 table)
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 71f34d4ae4b367b32fb36134acbf4f4f7ee681f4.1579374329.git.berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_alloc_cluster_offset() and qcow2_get_cluster_offset() always
return offsets that are cluster-aligned so don't just check that they
are sector-aligned.
The check in qcow2_co_preadv_task() is also replaced by an assertion
for the same reason.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 558ba339965f858bede4c73ce3f50f0c0493597d.1579374329.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The L1 table is read from disk using the byte-based bdrv_pread() and
is never accessed beyond its last element, so there's no need to
allocate more memory than that.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: b2e27214ec7b03a585931bcf383ee1ac3a641a10.1579374329.git.berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This is a bit more efficient than having to allocate and free memory
for each item.
The default size (60) is enough for all the existing incompatible
features or the "Unknown incompatible feature" message.
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20200115135626.19442-1-berto@igalia.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The standard cluster descriptor in L2 table entries has a field to
store the host cluster offset. When we need to get that offset from an
entry we use L2E_OFFSET_MASK to ensure that we only use the bits that
belong to that field.
But while that mask is used every time we read from an L2 entry, it
is never used when we write to it. Due to the QCOW_MAX_CLUSTER_OFFSET
limit set in the cluster allocation code QEMU can never produce
offsets that don't fit in that field so any such offset would indicate
a bug in QEMU.
Compressed cluster descriptors contain two fields (host cluster offset
and size of the compressed data) and the situation with them is
similar. In this case the masks are not constant but are stored in the
csize_mask and cluster_offset_mask fields of BDRVQcow2State.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20200113161146.20099-1-berto@igalia.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Aborts when sqe fails to be set as sqes cannot be returned to the
ring. Adds slow path for short reads for older kernels
Signed-off-by: Aarushi Mehta <mehta.aaru20@gmail.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20200120141858.587874-5-stefanha@redhat.com
Message-Id: <20200120141858.587874-5-stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
bdrv_mark_request_serialising is writing the overlap_offset and
overlap_bytes fields of BdrvTrackedRequest. Take bs->reqs_lock
for the whole duration of it, and not just when waiting for
serialising requests, so that tracked_request_overlaps does not
look at a half-updated request.
The new code does not unlock/relock around retries. This is unnecessary
because a retry is always preceded by a CoQueue wait, which already
releases and reacquires bs->reqs_lock.
Reported-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1578495356-46219-4-git-send-email-pbonzini@redhat.com
Message-Id: <1578495356-46219-4-git-send-email-pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Marking without waiting would not result in actual serialising behavior.
Thus, make a call bdrv_mark_request_serialising sufficient for
serialisation to happen.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1578495356-46219-3-git-send-email-pbonzini@redhat.com
Message-Id: <1578495356-46219-3-git-send-email-pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is unused since commit 00e30f0 ("block/backup: use backup-top instead
of write notifiers", 2019-10-01), drop it to simplify the code.
While at it, drop redundant assertions on flags.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1578495356-46219-2-git-send-email-pbonzini@redhat.com
Message-Id: <1578495356-46219-2-git-send-email-pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In iscsi_co_block_status(), we may have received num_descriptors == 0
from the iscsi server. Therefore, we can't unconditionally access
lbas->descriptors[0]. Add the missing check.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Peter Lieven <pl@kamp.de>
When querying an iSCSI server for the provisioning status of blocks (via
GET LBA STATUS), Qemu only validates that the response descriptor zero's
LBA matches the one requested. Given the SCSI spec allows servers to
respond with the status of blocks beyond the end of the LUN, Qemu may
have its heap corrupted by clearing/setting too many bits at the end of
its allocmap for the LUN.
A malicious guest in control of the iSCSI server could carefully program
Qemu's heap (by selectively setting the bitmap) and then smash it.
This limits the number of bits that iscsi_co_block_status() will try to
update in the allocmap so it can't overflow the bitmap.
Fixes: CVE-2020-1711
Cc: qemu-stable@nongnu.org
Signed-off-by: Felipe Franciosi <felipe@nutanix.com>
Signed-off-by: Peter Turschmid <peter.turschm@nutanix.com>
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_open_driver() allocates bs->opaque according to drv->instance_size.
There is no need to allocate it and overwrite opaque in
bdrv_backup_top_append().
Reproducer:
$ QTEST_QEMU_BINARY=./x86_64-softmmu/qemu-system-x86_64 valgrind -q --leak-check=full tests/test-replication -p /replication/secondary/start
==29792== 24 bytes in 1 blocks are definitely lost in loss record 52 of 226
==29792== at 0x483AB1A: calloc (vg_replace_malloc.c:762)
==29792== by 0x4B07CE0: g_malloc0 (in /usr/lib64/libglib-2.0.so.0.6000.7)
==29792== by 0x12BAB9: bdrv_open_driver (block.c:1289)
==29792== by 0x12BEA9: bdrv_new_open_driver (block.c:1359)
==29792== by 0x1D15CB: bdrv_backup_top_append (backup-top.c:190)
==29792== by 0x1CC11A: backup_job_create (backup.c:439)
==29792== by 0x1CD542: replication_start (replication.c:544)
==29792== by 0x1401B9: replication_start_all (replication.c:52)
==29792== by 0x128B50: test_secondary_start (test-replication.c:427)
...
Fixes: 7df7868b96 ("block: introduce backup-top filter driver")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All paths that lead to bdrv_backup_top_drop(), except for the call
from backup_clean(), imply that the BDS AioContext has already been
acquired, so doing it there too can potentially lead to QEMU hanging
on AIO_WAIT_WHILE().
An easy way to trigger this situation is by issuing a two actions
transaction, with a proper and a bogus blockdev-backup, so the second
one will trigger a rollback. This will trigger a hang with an stack
trace like this one:
#0 0x00007fb680c75016 in __GI_ppoll (fds=0x55e74580f7c0, nfds=1, timeout=<optimized out>,
timeout@entry=0x0, sigmask=sigmask@entry=0x0) at ../sysdeps/unix/sysv/linux/ppoll.c:39
#1 0x000055e743386e09 in ppoll (__ss=0x0, __timeout=0x0, __nfds=<optimized out>, __fds=<optimized out>)
at /usr/include/bits/poll2.h:77
#2 0x000055e743386e09 in qemu_poll_ns
(fds=<optimized out>, nfds=<optimized out>, timeout=<optimized out>) at util/qemu-timer.c:336
#3 0x000055e743388dc4 in aio_poll (ctx=0x55e7458925d0, blocking=blocking@entry=true)
at util/aio-posix.c:669
#4 0x000055e743305dea in bdrv_flush (bs=bs@entry=0x55e74593c0d0) at block/io.c:2878
#5 0x000055e7432be58e in bdrv_close (bs=0x55e74593c0d0) at block.c:4017
#6 0x000055e7432be58e in bdrv_delete (bs=<optimized out>) at block.c:4262
#7 0x000055e7432be58e in bdrv_unref (bs=bs@entry=0x55e74593c0d0) at block.c:5644
#8 0x000055e743316b9b in bdrv_backup_top_drop (bs=bs@entry=0x55e74593c0d0) at block/backup-top.c:273
#9 0x000055e74331461f in backup_job_create
(job_id=0x0, bs=bs@entry=0x55e7458d5820, target=target@entry=0x55e74589f640, speed=0, sync_mode=MIRROR_SYNC_MODE_FULL, sync_bitmap=sync_bitmap@entry=0x0, bitmap_mode=BITMAP_SYNC_MODE_ON_SUCCESS, compress=false, filter_node_name=0x0, on_source_error=BLOCKDEV_ON_ERROR_REPORT, on_target_error=BLOCKDEV_ON_ERROR_REPORT, creation_flags=0, cb=0x0, opaque=0x0, txn=0x0, errp=0x7ffddfd1efb0) at block/backup.c:478
#10 0x000055e74315bc52 in do_backup_common
(backup=backup@entry=0x55e746c066d0, bs=bs@entry=0x55e7458d5820, target_bs=target_bs@entry=0x55e74589f640, aio_context=aio_context@entry=0x55e7458a91e0, txn=txn@entry=0x0, errp=errp@entry=0x7ffddfd1efb0)
at blockdev.c:3580
#11 0x000055e74315c37c in do_blockdev_backup
(backup=backup@entry=0x55e746c066d0, txn=0x0, errp=errp@entry=0x7ffddfd1efb0)
at /usr/src/debug/qemu-kvm-4.2.0-2.module+el8.2.0+5135+ed3b2489.x86_64/./qapi/qapi-types-block-core.h:1492
#12 0x000055e74315c449 in blockdev_backup_prepare (common=0x55e746a8de90, errp=0x7ffddfd1f018)
at blockdev.c:1885
#13 0x000055e743160152 in qmp_transaction
(dev_list=<optimized out>, has_props=<optimized out>, props=0x55e7467fe2c0, errp=errp@entry=0x7ffddfd1f088) at blockdev.c:2340
#14 0x000055e743287ff5 in qmp_marshal_transaction
(args=<optimized out>, ret=<optimized out>, errp=0x7ffddfd1f0f8)
at qapi/qapi-commands-transaction.c:44
#15 0x000055e74333de6c in do_qmp_dispatch
(errp=0x7ffddfd1f0f0, allow_oob=<optimized out>, request=<optimized out>, cmds=0x55e743c28d60 <qmp_commands>) at qapi/qmp-dispatch.c:132
#16 0x000055e74333de6c in qmp_dispatch
(cmds=0x55e743c28d60 <qmp_commands>, request=<optimized out>, allow_oob=<optimized out>)
at qapi/qmp-dispatch.c:175
#17 0x000055e74325c061 in monitor_qmp_dispatch (mon=0x55e745908030, req=<optimized out>)
at monitor/qmp.c:145
#18 0x000055e74325c6fa in monitor_qmp_bh_dispatcher (data=<optimized out>) at monitor/qmp.c:234
#19 0x000055e743385866 in aio_bh_call (bh=0x55e745807ae0) at util/async.c:117
#20 0x000055e743385866 in aio_bh_poll (ctx=ctx@entry=0x55e7458067a0) at util/async.c:117
#21 0x000055e743388c54 in aio_dispatch (ctx=0x55e7458067a0) at util/aio-posix.c:459
#22 0x000055e743385742 in aio_ctx_dispatch
(source=<optimized out>, callback=<optimized out>, user_data=<optimized out>) at util/async.c:260
#23 0x00007fb68543e67d in g_main_dispatch (context=0x55e745893a40) at gmain.c:3176
#24 0x00007fb68543e67d in g_main_context_dispatch (context=context@entry=0x55e745893a40) at gmain.c:3829
#25 0x000055e743387d08 in glib_pollfds_poll () at util/main-loop.c:219
#26 0x000055e743387d08 in os_host_main_loop_wait (timeout=<optimized out>) at util/main-loop.c:242
#27 0x000055e743387d08 in main_loop_wait (nonblocking=<optimized out>) at util/main-loop.c:518
#28 0x000055e74316a3c1 in main_loop () at vl.c:1828
#29 0x000055e743016a72 in main (argc=<optimized out>, argv=<optimized out>, envp=<optimized out>)
at vl.c:4504
Fix this by not acquiring the AioContext there, and ensuring all paths
leading to it have it already acquired (backup_clean()).
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1782111
Signed-off-by: Sergio Lopez <slp@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since commit 6040aedddb "virtio-blk:
make queue size configurable",if the user set the queue size to
more than 128 ,it will not take effect. That's because linux aio's
maximum outstanding requests at a time is always less than or equal
to 128.
This patch simply increase MAX_EVENTS to a larger hardcoded value of
1024 as a shortterm fix.
Signed-off-by: wangyong <wang.yongD@h3c.com>
Message-id: faa5781afd354a96a0be152b288f636f@h3c.com
Message-Id: <faa5781afd354a96a0be152b288f636f@h3c.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When dropping backup-top, we need to drain the node before freeing the
BlockCopyState. Otherwise, requests may still be in flight and then the
assertion in shres_destroy() will fail.
(This becomes visible in intermittent failure of 056.)
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191219182638.104621-1-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
QEMU currently supports writing compressed data of the size equal to
one cluster. This patch allows writing QCOW2 compressed data that
exceed one cluster. Now, we split buffered data into separate clusters
and write them compressed using the block/aio_task API.
Suggested-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 1575288906-551879-3-git-send-email-andrey.shinkevich@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Allow writing all the data compressed through the filter driver.
The written data will be aligned by the cluster size.
Based on the QEMU current implementation, that data can be written to
unallocated clusters only. May be used for a backup job.
Suggested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 1575288906-551879-2-git-send-email-andrey.shinkevich@virtuozzo.com
[mreitz: Replace NULL bdrv_get_format_name() by "(no format)"]
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_can_store_new_dirty_bitmap works wrong, as it considers only
bitmaps already stored in the qcow2 image and ignores persistent
BdrvDirtyBitmap objects.
So, let's instead count persistent BdrvDirtyBitmaps. We load all qcow2
bitmaps on open, so there should not be any bitmap in the image for
which we don't have BdrvDirtyBitmaps version. If it is - it's a kind of
corruption, and no reason to check for corruptions here (open() and
close() are better places for it).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191014115126.15360-2-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
This avoid a memory leak when qom-set is called to set throttle_group
limits, here is an easy way to reproduce:
1. run qemu-iotests as follow and check the result with asan:
./check -qcow2 184
Following is the asan output backtrack:
Direct leak of 912 byte(s) in 3 object(s) allocated from:
#0 0xffff8d7ab3c3 in __interceptor_calloc (/lib64/libasan.so.4+0xd33c3)
#1 0xffff8d4c31cb in g_malloc0 (/lib64/libglib-2.0.so.0+0x571cb)
#2 0x190c857 in qobject_input_start_struct /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qapi/qobject-input-visitor.c:295
#3 0x19070df in visit_start_struct /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qapi/qapi-visit-core.c:49
#4 0x1948b87 in visit_type_ThrottleLimits qapi/qapi-visit-block-core.c:3759
#5 0x17e4aa3 in throttle_group_set_limits /mnt/sdc/qemu-master/qemu-4.2.0-rc0/block/throttle-groups.c:900
#6 0x1650eff in object_property_set /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/object.c:1272
#7 0x1658517 in object_property_set_qobject /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/qom-qobject.c:26
#8 0x15880bb in qmp_qom_set /mnt/sdc/qemu-master/qemu-4.2.0-rc0/qom/qom-qmp-cmds.c:74
#9 0x157e3e3 in qmp_marshal_qom_set qapi/qapi-commands-qom.c:154
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: PanNengyuan <pannengyuan@huawei.com>
Message-id: 1574835614-42028-1-git-send-email-pannengyuan@huawei.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Sometimes it is useful to be able to add a node to the block graph that
takes or unshare a certain set of permissions for debugging purposes.
This patch adds this capability to blkdebug.
(Note that you cannot make blkdebug release or share permissions that it
needs to take or cannot share, because this might result in assertion
failures in the block layer. But if the blkdebug node has no parents,
it will not take any permissions and share everything by default, so you
can then freely choose what permissions to take and share.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191108123455.39445-4-mreitz@redhat.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
- qemu-img: fix info --backing-chain --image-opts
- Error out on image creation with conflicting size options
- Fix external snapshot with VM state
- hmp: Allow using qdev ID for qemu-io command
- Misc code cleanup
- Many iotests improvements
-----BEGIN PGP SIGNATURE-----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=laVP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- qemu-img: fix info --backing-chain --image-opts
- Error out on image creation with conflicting size options
- Fix external snapshot with VM state
- hmp: Allow using qdev ID for qemu-io command
- Misc code cleanup
- Many iotests improvements
# gpg: Signature made Thu 19 Dec 2019 17:23:11 GMT
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (30 commits)
iotests: Test external snapshot with VM state
hmp: Allow using qdev ID for qemu-io command
block: Activate recursively even for already active nodes
iotests: 211: Remove duplication with VM.blockdev_create()
iotests: 207: Remove duplication with VM.blockdev_create()
iotests: 266: Convert to VM.blockdev_create()
iotests: 237: Convert to VM.blockdev_create()
iotests: 213: Convert to VM.blockdev_create()
iotests: 212: Convert to VM.blockdev_create()
iotests: 210: Convert to VM.blockdev_create()
iotests: 206: Convert to VM.blockdev_create()
iotests: 255: Drop blockdev_create()
iotests: Create VM.blockdev_create()
qcow2: Move error check of local_err near its assignment
iotests: Fix IMGOPTSSYNTAX for nbd
iotests/273: Filter format-specific information
iotests: Add more "_require_drivers" checks to the shell-based tests
MAINTAINERS: fix qcow2-bitmap.c under Dirty Bitmaps header
qcow2: Use offset_into_cluster()
iotests: Support job-complete in run_job()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The local_err check outside of the if block was necessary
when it was introduced in commit d1258dd0c8 because it needed to be
executed even if qcow2_load_autoloading_dirty_bitmaps() returned false.
After some modifications that all required the error check to remain
where it is, commit 9c98f145df finally moved the
qcow2_load_dirty_bitmaps() call into the if block, so now the error
check should be there, too.
Signed-off-by: Guoyi Tu <tu.guoyi@h3c.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There's a couple of places left in the qcow2 code that still do the
calculation manually, so let's replace them.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In the common case, qcow2_co_pwrite_zeroes() already only modifies
metadata case, so we're fine with or without BDRV_REQ_NO_FALLBACK set.
The only exception is when using an external data file, where the
request is passed down to the block driver of the external data file. We
are forwarding the BDRV_REQ_NO_FALLBACK flag there, though, so this is
fine, too.
Declare the flag supported therefore.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
All callers of nbd_iter_channel_error() pass the address of a
local_err variable, and only call this function if an error has
already occurred, using this function to propagate that error.
This is already implied by its name (local_err instead of the classic
errp), but it is worth additionally stressing this by adding an
assertion to make it part of the function contract.
The local_err parameter is not here to return information about
nbd_iter_channel_error failure. Instead it's assumed to be filled when
passed to the function. This is already stressed by its name
(local_err, instead of classic errp). Stress it additionally by
assertion.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205174635.18758-22-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@Redhat.com>
Message-Id: <20191205174635.18758-11-vsementsov@virtuozzo.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Here is double bug:
First, return error but not set errp. This may lead to:
qmp block-dirty-bitmap-remove may report success when actually failed
block-dirty-bitmap-remove used in a transaction will crash, as
qmp_transaction will think that it returned success and will call
block_dirty_bitmap_remove_commit which will crash, as state->bitmap is
NULL
Second (like in anecdote), this case is not an error at all. As it is
documented in the comment above bdrv_co_remove_persistent_dirty_bitmap
definition, absence of bitmap is not an error, and similar case handled
at start of qcow2_co_remove_persistent_dirty_bitmap, it returns 0 when
there is no bitmaps at all.
But when there are some bitmaps, but not the requested one, it return
error with errp unset.
Fix that.
Trigger:
1. create persistent bitmap A
2. shutdown vm (bitmap A is synced)
3. start vm
4. create persistent bitmap B
5. remove bitmap B - it fails (and crashes if in transaction)
Potential workaround (rather invasive to ask clients to implement it):
1. create persistent bitmap A
2. shutdown vm
3. start vm
4. create persistent bitmap B
5. remember, that we want to remove bitmap B after vm shutdown
...
some other operations
...
6. vm shutdown
7. start vm in stopped mode, and remove all bitmaps marked for removing
8. stop vm
Fixes: b56a1e3175
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191205193049.30666-1-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
[eblake: commit message tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
raw_aio_attach_aio_context() passes uninitialized Error *local_err by
reference to laio_init() via aio_setup_linux_aio(). When laio_init()
fails, it passes it on to error_setg_errno(), tripping error_setv()'s
assertion unless @local_err is null by dumb luck.
Fix by initializing @local_err properly.
Fixes: ed6e216171
Cc: Nishanth Aravamudan <naravamudan@digitalocean.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20191130194240.10517-4-armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Fix bitmap migration with dirty-bitmaps capability enabled and shared
storage. We should ignore IN_USE bitmaps in the image on target, when
migrating bitmaps through migration channel, see new comment below.
Fixes: 74da6b9435
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191125125229.13531-2-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Qemu as server currently won't accept export names larger than 256
bytes, nor create dirty bitmap names longer than 1023 bytes, so most
uses of qemu as client or server have no reason to get anywhere near
the NBD spec maximum of a 4k limit per string.
However, we weren't actually enforcing things, ignoring when the
remote side violates the protocol on input, and also having several
code paths where we send oversize strings on output (for example,
qemu-nbd --description could easily send more than 4k). Tighten
things up as follows:
client:
- Perform bounds check on export name and dirty bitmap request prior
to handing it to server
- Validate that copied server replies are not too long (ignoring
NBD_INFO_* replies that are not copied is not too bad)
server:
- Perform bounds check on export name and description prior to
advertising it to client
- Reject client name or metadata query that is too long
- Adjust things to allow full 4k name limit rather than previous
256 byte limit
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-4-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
We document that for qcow2 persistent bitmaps, the name cannot exceed
1023 bytes. It is inconsistent if transient bitmaps do not have to
abide by the same limit, and it is unlikely that any existing client
even cares about using bitmap names this long. It's time to codify
that ALL bitmaps managed by qemu (whether persistent in qcow2 or not)
have a documented maximum length.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20191114024635.11363-3-eblake@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
There are two issues in In check_constraints_on_bitmap(),
1) The sanity check on the granularity will cause uint64_t
integer left-shift overflow when cluster_size is 2M and the
granularity is BIGGER than 32K.
2) The way to calculate image size that the maximum bitmap
supported can map to is a bit incorrect.
This patch fix it by add a helper function to calculate the
number of bytes needed by a normal bitmap in image and compare
it to the maximum bitmap bytes supported by qemu.
Fixes: 5f72826e7f
Signed-off-by: Guoyi Tu <tu.guoyi@h3c.com>
Message-id: 4ba40cd1e7ee4a708b40899952e49f22@h3c.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
The XFS kernel driver has a bug that may cause data corruption for qcow2
images as of qemu commit c8bb23cbdb. We can work around it by
treating post-EOF fallocates as serializing up until infinity (INT64_MAX
in practice).
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191101152510.11719-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Make both bdrv_mark_request_serialising() and
bdrv_wait_serialising_requests() public so they can be used from block
drivers.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191101152510.11719-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
0e2402452f allowed writes larger than cluster, but that's
unsupported for compressed write. Fix it.
Fixes: 0e2402452f
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191029150934.26416-1-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEkb62CjDbPohX0Rgp9AfbAGHVz0AFAl2224ESHG1yZWl0ekBy
ZWRoYXQuY29tAAoJEPQH2wBh1c9AeXMH/RXKEX4BZYMRKCe41P18tJC9Bl2x0T20
YeOsZVvpARlr7o/36BF2kGFF4MnL0OQ+9ELuyROX865rk/VL2rWqnHDE5oQM889a
dFwMs+0zvNbig3iLNcw0H5OkE2mrdM+a1EUdn/lBe/39Z8dPqPxRGqIYHq38Ugdu
emwSy1nWen7o0f71HRJfyVtI3KcrzXx71FrA/FY2yL/eHz+zRYGZj2SpAdFPkXP/
lgaz+m0tWhnSW1QzEOXB0Gh69ULt/DczCinYmv5qUY1noW5TPPtiDNCQTts5O4ba
oJsR3AJv5/l9m65JTmiyQSqnQfPcstrQ5FqOcSnP637cfqUFyWsvdks=
=L7v1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2019-10-28' into staging
Block patches for softfreeze:
- iotest patches
- Improve performance of the mirror block job in write-blocking mode
- Limit memory usage for the backup block job
- Add discard and write-zeroes support to the NVMe host block driver
- Fix a bug in the mirror job
- Prevent the qcow2 driver from creating technically non-compliant qcow2
v3 images (where there is not enough extra data for snapshot table
entries)
- Allow callers of bdrv_truncate() (etc.) to determine whether the file
must be resized to the exact given size or whether it is OK for block
devices not to shrink
# gpg: Signature made Mon 28 Oct 2019 12:13:53 GMT
# gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40
# gpg: issuer "mreitz@redhat.com"
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2019-10-28: (69 commits)
qemu-iotests: restrict 264 to qcow2 only
Revert "qemu-img: Check post-truncation size"
block: Pass truncate exact=true where reasonable
block: Let format drivers pass @exact
block: Evaluate @exact in protocol drivers
block: Add @exact parameter to bdrv_co_truncate()
block: Do not truncate file node when formatting
block/cor: Drop cor_co_truncate()
block: Handle filter truncation like native impl.
iotests: Test qcow2's snapshot table handling
iotests: Add peek_file* functions
qcow2: Fix v3 snapshot table entry compliancy
qcow2: Repair snapshot table with too many entries
qcow2: Fix overly long snapshot tables
qcow2: Keep track of the snapshot table length
qcow2: Fix broken snapshot table entries
qcow2: Add qcow2_check_fix_snapshot_table()
qcow2: Separate qcow2_check_read_snapshot_table()
qcow2: Write v3-compliant snapshot list on upgrade
qcow2: Put qcow2_upgrade() into its own function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a change in behavior, so all instances need a good
justification. The comments added here should explain my reasoning.
qed already had a comment that suggests it always expected
bdrv_truncate()/blk_truncate() to behave as if exact=true were passed
(c743849bee came eight months before 55b949c847), so it was simply
broken until now.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-8-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
[mreitz: Changed comment in qed.c to explain why a new QED file must be
empty, as requested and suggested by Maxim]
Signed-off-by: Max Reitz <mreitz@redhat.com>
When truncating a format node, the @exact parameter is generally handled
simply by virtue of the format storing the new size in the image
metadata. Such formats do not need to pass on the parameter to their
file nodes.
There are exceptions, though:
- raw and crypto cannot store the image size, and thus must pass on
@exact.
- When using qcow2 with an external data file, it just makes sense to
keep its size in sync with the qcow2 virtual disk (because the
external data file is the virtual disk). Therefore, we should pass
@exact when truncating it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-7-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
We have two protocol drivers that return success when trying to shrink a
block device even though they cannot shrink it. This behavior is now
only allowed with exact=false, so they should return an error with
exact=true.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-6-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
We have two drivers (iscsi and file-posix) that (in some cases) return
success from their .bdrv_co_truncate() implementation if the block
device is larger than the requested offset, but cannot be shrunk. Some
callers do not want that behavior, so this patch adds a new parameter
that they can use to turn off that behavior.
This patch just adds the parameter and lets the block/io.c and
block/block-backend.c functions pass it around. All other callers
always pass false and none of the implementations evaluate it, so that
this patch does not change existing behavior. Future patches take care
of that.
Suggested-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-5-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
There is no reason why the format drivers need to truncate the protocol
node when formatting it. When using the old .bdrv_co_create_ops()
interface, the file will be created with no size option anyway, which
generally gives it a size of 0. (Exceptions are block devices, which
cannot be truncated anyway.)
When using blockdev-create, the user must have given the file node some
size anyway, so there is no reason why we should override that.
qed is an exception, it needs the file to start completely empty (as
explained by c743849bee).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-4-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
No other filter driver has a .bdrv_co_truncate() implementation, and
there is no need to because the general block layer code can handle it
just as well.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-3-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Make the filter truncation (passing it through to bs->file) a
first-class citizen and handle it exactly as if it was the filter
driver's native implementation of .bdrv_co_truncate().
I do not see a reason not to, it makes the code a bit shorter, and may
be even more correct because this gets us to finish the write_req that
we prepared before (may be important to e.g. bring dirty bitmaps to the
correct size).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-2-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2 v3 images require every snapshot table entry to have at least 16
bytes of extra data. If they do not, let qemu-img check -r all fix it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-15-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The user cannot choose which snapshots are removed. This is fine
because we have chosen the maximum snapshot table size to be so large
(65536 entries) that it cannot be reasonably reached. If the snapshot
table exceeds this size, the image has probably been corrupted in some
way; in this case, it is most important to just make the image usable
such that the user can copy off at least the active layer.
(Also note that the snapshots will be removed only with "-r all", so a
plain "check" or "check -r leaks" will not delete any data.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-14-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We currently refuse to open qcow2 images with overly long snapshot
tables. This patch makes qemu-img check -r all drop all offending
entries past what we deem acceptable.
The user cannot choose which snapshots are removed. This is fine
because we have chosen the maximum snapshot table size to be so large
(64 MB) that it cannot be reasonably reached. If the snapshot table
exceeds this size, the image has probably been corrupted in some way; in
this case, it is most important to just make the image usable such that
the user can copy off at least the active layer.
(Also note that the snapshots will be removed only with "-r all", so a
plain "check" or "check -r leaks" will not delete any data.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-13-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When repairing the snapshot table, we truncate entries that have too
much extra data. This frees up space that we do not have to count
towards the snapshot table size.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-12-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The only case where we currently reject snapshot table entries is when
they have too much extra data. Fix them with qemu-img check -r all by
counting it as a corruption, reducing their extra_data_size, and then
letting qcow2_check_fix_snapshot_table() do the rest.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-11-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2_check_read_snapshot_table() can perform consistency checks, but it
cannot fix everything. Specifically, it cannot allocate new clusters,
because that should wait until the refcount structures are known to be
consistent (i.e., after qcow2_check_refcounts()). Thus, it cannot call
qcow2_write_snapshots().
Do that in qcow2_check_fix_snapshot_table(), which is called after
qcow2_check_refcounts().
Currently, there is nothing that would set result->corruptions, so this
is a no-op. A follow-up patch will change that.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-10-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reading the snapshot table can fail. That is a problem when we want to
repair the image.
Therefore, stop reading the snapshot table in qcow2_do_open() in check
mode. Instead, add a new function qcow2_check_read_snapshot_table()
that reads the snapshot table at a later point. In the future, we want
to handle errors here and fix them.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-9-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
qcow2 v3 requires every snapshot table entry to have two extra data
fields: The 64-bit VM state size, and the virtual disk size. Both are
optional for v2 images, so they may not be present.
qcow2_upgrade() therefore should update the snapshot table to ensure all
entries have these extra data fields.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1727347
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-8-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This does not make sense right now, but it will make sense once we need
to do more than to just update s->qcow_version.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-7-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Updating the snapshot list will be useful when upgrading a v2 image to
v3, so we will need to call this function in qcow2.c.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-6-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The qcow2 specification says to ignore unknown extra data fields in
snapshot table entries. Currently, we discard it whenever we update the
image, which is a bit different from "ignore".
This patch makes the qcow2 driver keep all unknown extra data fields
when updating an image's snapshot table.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-5-mreitz@redhat.com
[mreitz: Adjusted comments as proposed by Eric]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191011152814.14791-3-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
mirror_exit_common() may be called twice (if it is called from
mirror_prepare() and fails, it will be called from mirror_abort()
again).
In such a case, many of the pointers in the MirrorBlockJob object will
already be freed. This can be seen most reliably for s->target, which
is set to NULL (and then dereferenced by blk_bs()).
Cc: qemu-stable@nongnu.org
Fixes: 737efc1eda
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191014153931.20699-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
No reason to limit buffered copy to one cluster. Let's allow up to 1
MiB.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191022111805.3432-7-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Currently total allocation for parallel requests to block-copy instance
is unlimited. Let's limit it to 128 MiB.
For now block-copy is used only in backup, so actually we limit total
allocation for backup job.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191022111805.3432-6-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Merge copying code into one function block_copy_do_copy, which only
calls bdrv_ io functions and don't do any synchronization (like dirty
bitmap set/reset).
Refactor block_copy() function so that it takes full decision about
size of chunk to be copied and does all the synchronization (checking
intersecting requests, set/reset dirty bitmaps).
It will help:
- introduce parallel processing of block_copy iterations: we need to
calculate chunk size, start async chunk copying and go to the next
iteration
- simplify synchronization improvement (like memory limiting in
further commit and reducing critical section (now we lock the whole
requested range, when actually we need to lock only dirty region
which we handle at the moment))
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191022111805.3432-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Large copy range may imply memory allocation and large io effort, so
using 2G copy range request may be bad idea. Let's limit it to 16 MiB.
It also helps the following patch to refactor copy-with-offload
fallback to copy-with-bounce-buffer.
Note, that total memory usage of backup is still not limited, it will
be fixed in further commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191022111805.3432-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Move bounce_buffer allocation block_copy_with_bounce_buffer. This
commit simplifies further work on implementing copying by larger chunks
(of different size) and further asynchronous handling of block_copy
iterations (with help of block/aio_task API).
Allocation works fast, a lot faster than disk io, so it's not a problem
that we now allocate/free bounce_buffer more times. And we anyway will
have to allocate several bounce_buffers for parallel execution of loop
iterations in future.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191022111805.3432-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This reverts commit 9adc1cb49a.
"mirror: Only mirror granularity-aligned chunks"
Since previous commit unaligned chunks are supported by
do_sync_target_write.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191011090711.19940-6-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Prior 9adc1cb49a do_sync_target_write had a bug: it reset aligned-up
region in the dirty bitmap, which means that we may not copy some bytes
and assume them copied, which actually leads to producing corrupted
target.
So 9adc1cb49a forced dirty bitmap granularity to be
request_alignment for mirror-top filter, so we are not working with
unaligned requests. However forcing large alignment obviously decreases
performance of unaligned requests.
This commit provides another solution for the problem: if unaligned
padding is already dirty, we can safely ignore it, as
1. It's dirty, it will be copied by mirror_iteration anyway
2. It's dirty, so skipping it now we don't increase dirtiness of the
bitmap and therefore don't damage "synchronicity" of the
write-blocking mirror.
If unaligned padding is not dirty, we just write it, no reason to touch
dirty bitmap if we succeed (on failure we'll set the whole region
ofcourse, but we loss "synchronicity" on failure anyway).
Note: we need to disable dirty_bitmap, otherwise we will not be able to
see in do_sync_target_write bitmap state before current operation. We
may of course check dirty bitmap before the operation in
bdrv_mirror_top_do_write and remember it, but we don't need active
dirty bitmap for write-blocking mirror anyway.
New code-path is unused until the following commit reverts
9adc1cb49a.
Suggested-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191011090711.19940-5-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add blk write function with qiov_offset parameter. It's needed for the
following commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191011090711.19940-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
do_sync_target_write is called from bdrv_mirror_top_do_write after
write/discard operation, all inside active_write/active_write_settle
protecting us from mirror iteration. So the whole area is dirty for
sure, no reason to examine dirty bitmap.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191011090711.19940-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
There are three page size in qemu:
real host page size
host page size
target page size
All of them have dedicate variable to represent. For the last two, we
use the same form in the whole qemu project, while for the first one we
use two forms: qemu_real_host_page_size and getpagesize().
qemu_real_host_page_size is defined to be a replacement of
getpagesize(), so let it serve the role.
[Note] Not fully tested for some arch or device.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20191013021145.16011-3-richardw.yang@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qcow2_detect_metadata_preallocation() calls qcow2_get_refcount() which
requires s->lock to be taken to protect its accesses to the refcount
table and refcount blocks. However, nothing in this code path actually
took the lock. This could cause the same cache entry to be used by two
requests at the same time, for different tables at different offsets,
resulting in image corruption.
As it would be preferable to base the detection on consistent data (even
though it's just heuristics), let's take the lock not only around the
qcow2_get_refcount() calls, but around the whole function.
This patch takes the lock in qcow2_co_block_status() earlier and asserts
in qcow2_detect_metadata_preallocation() that we hold the lock.
Fixes: 69f47505ee
Cc: qemu-stable@nongnu.org
Reported-by: Michael Weiser <michael.weiser@gmx.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Michael Weiser <michael.weiser@gmx.de>
Reviewed-by: Michael Weiser <michael.weiser@gmx.de>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
After commit 00e30f05de, there is no more "goto error" points
after job creation, so after "error:" @job is always NULL and we don't
need roll-back job creation.
Reported-by: Coverity (CID 1406402)
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Implement reconnect. To achieve this:
1. add new modes:
connecting-wait: means, that reconnecting is in progress, and there
were small number of reconnect attempts, so all requests are
waiting for the connection.
connecting-nowait: reconnecting is in progress, there were a lot of
attempts of reconnect, all requests will return errors.
two old modes are used too:
connected: normal state
quit: exiting after fatal error or on close
Possible transitions are:
* -> quit
connecting-* -> connected
connecting-wait -> connecting-nowait (transition is done after
reconnect-delay seconds in connecting-wait mode)
connected -> connecting-wait
2. Implement reconnect in connection_co. So, in connecting-* mode,
connection_co, tries to reconnect unlimited times.
3. Retry nbd queries on channel error, if we are in connecting-wait
state.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20191009084158.15614-3-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The only reason I can imagine for this strange code at the very-end of
bdrv_reopen_commit is the fact that bs->read_only updated after
calling drv->bdrv_reopen_commit in bdrv_reopen_commit. And in the same
time, prior to previous commit, qcow2_reopen_bitmaps_rw did a wrong
check for being writable, when actually it only need writable file
child not self.
So, as it's fixed, let's move things to correct place.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190927122355.7344-10-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
- Correct check for write access to file child, and in correct place
(only if we want to write).
- Support reopen rw -> rw (which will be used in following commit),
for example, !bdrv_dirty_bitmap_readonly() is not a corruption if
bitmap is marked IN_USE in the image.
- Consider unexpected bitmap as a corruption and check other
combinations of in-image and in-RAM bitmaps.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190927122355.7344-9-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
qcow2_reopen_bitmaps_ro wants to store bitmaps and then mark them all
readonly. But the latter don't work, as
qcow2_store_persistent_dirty_bitmaps removes bitmaps after storing.
It's OK for inactivation but bad idea for reopen-ro. And this leads to
the following bug:
Assume we have persistent bitmap 'bitmap0'.
Create external snapshot
bitmap0 is stored and therefore removed
Commit snapshot
now we have no bitmaps
Do some writes from guest (*)
they are not marked in bitmap
Shutdown
Start
bitmap0 is loaded as valid, but it is actually broken! It misses
writes (*)
Incremental backup
it will be inconsistent
So, let's stop removing bitmaps on reopen-ro. But don't rejoice:
reopening bitmaps to rw is broken too, so the whole scenario will not
work after this patch and we can't enable corresponding test cases in
260 iotests still. Reopening bitmaps rw will be fixed in the following
patches.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190927122355.7344-7-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
The function is unused, drop it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190927122355.7344-6-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
Firstly, no reason to optimize failure path. Then, function name is
ambiguous: it checks for readonly and similar things, but someone may
think that it will ignore normal bitmaps which was just unchanged, and
this is in bad relation with the fact that we should drop IN_USE flag
for unchanged bitmaps in the image.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190927122355.7344-5-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
bdrv_dirty_bitmap_next is always used in same pattern. So, split it
into _next and _first, instead of combining two functions into one and
add FOR_EACH_DIRTY_BITMAP macro.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190916141911.5255-5-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
mutex field is just a pointer to bs->dirty_bitmap_mutex, so no needs
to store it in BdrvDirtyBitmap when we have bs pointer in it (since
previous patch).
Drop mutex field. Constantly use bdrv_dirty_bitmaps_lock/unlock in
block/dirty-bitmap.c to make it more obvious that it's not per-bitmap
lock. Still, for simplicity, leave bdrv_dirty_bitmap_lock/unlock
functions as an external API.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190916141911.5255-4-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
Add bs field to BdrvDirtyBitmap structure. Drop BlockDriverState
parameter from bitmap APIs where possible.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190916141911.5255-3-vsementsov@virtuozzo.com
[Rebased on top of block-copy. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
Drop meta bitmaps, as they are unused.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190916141911.5255-2-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
qmp_block_dirty_bitmap_add and do_block_dirty_bitmap_remove do acquire
aio context since 0a6c86d024. But this is not enough: we also must
lock qcow2 mutex when access in-image metadata. Especially it concerns
freeing qcow2 clusters.
To achieve this, move qcow2_can_store_new_dirty_bitmap and
qcow2_remove_persistent_dirty_bitmap to coroutine context.
Since we work in coroutines in correct aio context, we don't need
context acquiring in blockdev.c anymore, drop it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190920082543.23444-4-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
It's more comfortable to not deal with local_err.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190920082543.23444-3-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
block/dirty-bitmap.c seems to be more appropriate for it and
bdrv_remove_persistent_dirty_bitmap already in it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190920082543.23444-2-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
When the COW areas are included, the size of an allocation can exceed
INT_MAX. This is kind of limited by handle_alloc() in that it already
caps avail_bytes at INT_MAX, but the number of clusters still reflects
the original length.
This can have all sorts of effects, ranging from the storage layer write
call failing to image corruption. (If there were no image corruption,
then I suppose there would be data loss because the .cow_end area is
forced to be empty, even though there might be something we need to
COW.)
Fix all of it by limiting nb_clusters so the equivalent number of bytes
will not exceed INT_MAX.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The BDRV_REQ_NO_FALLBACK flag means that an operation should only be
performed if it can be offloaded or otherwise performed efficiently.
However a misaligned write request requires a RMW so we should return
an error and let the caller decide how to proceed.
This hits an assertion since commit c8bb23cbdb if the required
alignment is larger than the cluster size:
qemu-img create -f qcow2 -o cluster_size=2k img.qcow2 4G
qemu-io -c "open -o driver=qcow2,file.align=4k blkdebug::img.qcow2" \
-c 'write 0 512'
qemu-io: block/io.c:1127: bdrv_driver_pwritev: Assertion `!(flags & BDRV_REQ_NO_FALLBACK)' failed.
Aborted
The reason is that when writing to an unallocated cluster we try to
skip the copy-on-write part and zeroize it using BDRV_REQ_NO_FALLBACK
instead, resulting in a write request that is too small (2KB cluster
size vs 4KB required alignment).
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Replay is capable of recording normal BH events, but sometimes
there are single use callbacks scheduled with aio_bh_schedule_oneshot
function. This patch enables recording and replaying such callbacks.
Block layer uses these events for calling the completion function.
Replaying these calls makes the execution deterministic.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In record/replay mode bdrv queue is controlled by replay mechanism.
It does not allow saving or loading the snapshots
when bdrv queue is not empty. Stopping the VM is not blocked by nonempty
queue, but flushing the queue is still impossible there,
because it may cause deadlocks in replay mode.
This patch disables bdrv_drain_all and bdrv_flush_all in
record/replay mode.
Stopping the machine when the IO requests are not finished is needed
for the debugging. E.g., breakpoint may be set at the specified step,
and forcing the IO requests to finish may break the determinism
of the execution.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch enables making snapshots with blkreplay used in
block devices.
This function is required to make bdrv_snapshot_goto without
calling .bdrv_open which is not implemented.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
qemu is currently not able to detect truncated vhdx image files.
Add a basic check if all allocated blocks are reachable at open and
report all errors during bdrv_co_check.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Drop write notifiers and use filter node instead.
= Changes =
1. Add filter-node-name argument for backup qmp api. We have to do it
in this commit, as 257 needs to be fixed.
2. There are no more write notifiers here, so is_write_notifier
parameter is dropped from block-copy paths.
3. To sync with in-flight requests at job finish we now have drained
removing of the filter, we don't need rw-lock.
4. Block-copy is now using BdrvChildren instead of BlockBackends
5. As backup-top owns these children, we also move block-copy state
into backup-top's ownership.
= Iotest changes =
56: op-blocker doesn't shoot now, as we set it on source, but then
check on filter, when trying to start second backup.
To keep the test we instead can catch another collision: both jobs will
get 'drive0' job-id, as job-id parameter is unspecified. To prevent
interleaving with file-posix locks (as they are dependent on config)
let's use another target for second backup.
Also, it's obvious now that we'd like to drop this op-blocker at all
and add a test-case for two backups from one node (to different
destinations) actually works. But not in these series.
141: Output changed: prepatch, "Node is in use" comes from bdrv_has_blk
check inside qmp_blockdev_del. But we've dropped block-copy blk
objects, so no more blk objects on source bs (job blk is on backup-top
filter bs). New message is from op-blocker, which is the next check in
qmp_blockdev_add.
257: The test wants to emulate guest write during backup. They should
go to filter node, not to original source node, of course. Therefore we
need to specify filter node name and use it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191001131409.14202-6-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Backup-top filter caches write operations and does copy-before-write
operations.
The driver will be used in backup instead of write-notifiers.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191001131409.14202-5-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split block_copy_set_callbacks out of block_copy_state_new. It's needed
for further commit: block-copy will use BdrvChildren of backup-top
filter, so it will be created from backup-top filter creation function.
But callbacks will still belong to backup job and will be set in
separate.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191001131409.14202-4-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This is logic-less refactoring, which simplifies further patch, as
we'll need write_flags for backup-top filter creation and backup-top
should be created before block job creation.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191001131409.14202-3-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Move synchronization mechanism to block-copy, to be able to use one
block-copy instance from backup job and backup-top filter in parallel.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20191001131409.14202-2-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
A block driver can provide a callback to report driver-specific
statistics.
file-posix driver now reports discard statistics
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190923121737.83281-10-anton.nefedov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This will help to identify how many of the user-issued discard operations
(accounted on a device level) have actually suceeded down on the host file
(even though the numbers will not be exactly the same if non-raw format
driver is used (e.g. qcow2 sending metadata discards)).
Note that these numbers will not include discards triggered by
write-zeroes + MAY_UNMAP calls.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190923121737.83281-9-anton.nefedov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Each block_acct_done/failed call is designed to correspond to a
previous block_acct_start call, which initializes the stats cookie.
However sometimes it is not the case, e.g. some error paths might
report the same cookie twice because it is hard to accurately track if
the cookie was reported yet or not.
This patch cleans the cookie after report.
(Note: block_acct_failed/done without a previous block_acct_start at
all should be avoided. Uninitialized cookie might hold a garbage value
and there is still "< BLOCK_MAX_IOTYPE" assertion for that)
It will be particularly useful in ide code where it's hard to
keep track whether the request done its accounting or not: in the
following patch of the series, trim requests will do the accounting
separately.
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190923121737.83281-4-anton.nefedov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20190923121737.83281-3-anton.nefedov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split block_copy to separate file, to be cleanly shared with backup-top
filter driver in further commits.
It's a clean movement, the only change is drop "static" from interface
functions.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190920142056.12778-8-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We need to fix comment style around block-copy functions before further
moving them to separate file to satisfy checkpatch. But do more: fix
all comments style. Also, seems like doubled first asterisk is not
forbidden, but drop it too for consistency.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190920142056.12778-7-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split copying code part from backup to "block-copy", including separate
state structure and function renaming. This is needed to share it with
backup-top filter driver in further commits.
Notes:
1. As BlockCopyState keeps own BlockBackend objects, remaining
job->common.blk users only use it to get bs by blk_bs() call, so clear
job->commen.blk permissions set in block_job_create and add
job->source_bs to be used instead of blk_bs(job->common.blk), to keep
it more clear which bs we use when introduce backup-top filter in
further commit.
2. Rename s/initializing_bitmap/skip_unallocated/ to sound a bit better
as interface to BlockCopyState
3. Split is not very clean: there left some duplicated fields, backup
code uses some BlockCopyState fields directly, let's postpone it for
further improvements and keep this comment simpler for review.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190920142056.12778-6-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190920142056.12778-5-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Split copying logic which will be shared with backup-top filter.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190920142056.12778-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We shouldn't try to copy bytes beyond EOF. Fix it.
Fixes: 9ded4a0114
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190920142056.12778-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Of course, QEMU_ALIGN_UP is a typo, it should be QEMU_ALIGN_DOWN, as we
are trying to find aligned size which satisfy both source and target.
Also, don't ignore too small max_transfer. In this case seems safer to
disable copy_range.
Fixes: 9ded4a0114
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190920142056.12778-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
It improves performance for fragmented qcow2 images.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190916175324.18478-6-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Similarly to previous commit, prepare for parallelizing write-loop
iterations.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190916175324.18478-5-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Further patch will run partial requests of iterations of
qcow2_co_preadv in parallel for performance reasons. To prepare for
this, separate part which may be parallelized into separate function
(qcow2_co_preadv_task).
While being here, also separate encrypted clusters reading to own
function, like it is done for compressed reading.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190916175324.18478-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Common interface for aio task loops. To be used for improving
performance of synchronous io loops in qcow2, block-stream,
copy-on-read, and may be other places.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190916175324.18478-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
We must not write data to inactive nodes, and a COR is certainly
something we can simply not do without upsetting anyone. So skip COR
operations on inactive nodes.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20191001174827.11081-2-mreitz@redhat.com
Message-Id: <20191001174827.11081-2-mreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Nodes involved in internal snapshots were those that were returned by
bdrv_next(), inserted and not read-only. bdrv_next() in turn returns all
nodes that are either the root node of a BlockBackend or monitor-owned
nodes.
With the typical -drive use, this worked well enough. However, in the
typical -blockdev case, the user defines one node per option, making all
nodes monitor-owned nodes. This includes protocol nodes etc. which often
are not snapshottable, so "savevm" only returns an error.
Change the conditions so that internal snapshot still include all nodes
that have a BlockBackend attached (we definitely want to snapshot
anything attached to a guest device and probably also the built-in NBD
server; snapshotting block job BlockBackends is more of an accident, but
a preexisting one), but other monitor-owned nodes are only included if
they have no parents.
This makes internal snapshots usable again with typical -blockdev
configurations.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
Tested-by: Peter Krempa <pkrempa@redhat.com>
"qemu/cutils.h" contains various qemu_strtosz_*() functions
useful to convert strings to size. It seems natural to have
the opposite usage (from size to string) there too.
The function definition is already in util/cutils.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190903120555.7551-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
* Change the qcow2_co_{encrypt|decrypt} to just receive full host and
guest offsets and use this function directly instead of calling
do_perform_cow_encrypt (which is removed by that patch).
* Adjust qcow2_co_encdec to take full host and guest offsets as well.
* Document the qcow2_co_{encrypt|decrypt} arguments
to prevent the bug fixed in former commit from hopefully
happening again.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20190915203655.21638-3-mlevitsk@redhat.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[mreitz: Let perform_cow() return the error value returned by
qcow2_co_encrypt(), as proposed by Vladimir]
Signed-off-by: Max Reitz <mreitz@redhat.com>
This fixes subtle corruption introduced by luks threaded encryption
in commit 8ac0f15f33
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1745922
The corruption happens when we do a write that
* writes to two or more unallocated clusters at once
* doesn't fully cover the first sector
* doesn't fully cover the last sector
* uses luks encryption
In this case, when allocating the new clusters we COW both areas
prior to the write and after the write, and we encrypt them.
The above mentioned commit accidentally made it so we encrypt the
second COW area using the physical cluster offset of the first area.
The problem is that offset_in_cluster in do_perform_cow_encrypt
can be larger that the cluster size, thus cluster_offset
will no longer point to the start of the cluster at which encrypted
area starts.
Next patch in this series will refactor the code to avoid all these
assumptions.
In the bugreport that was triggered by rebasing a luks image to new,
zero filled base, which lot of such writes, and causes some files
with zero areas to contain garbage there instead.
But as described above it can happen elsewhere as well
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20190915203655.21638-2-mlevitsk@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
If we had done that all along, debugging would have been much simpler.
(Also, I/O errors are better than hangs.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190910124136.10565-8-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Background: As of cURL 7.59.0, it verifies that several functions are
not called from within a callback. Among these functions is
curl_multi_add_handle().
curl_read_cb() is a callback from cURL and not a coroutine. Waking up
acb->co will lead to entering it then and there, which means the current
request will settle and the caller (if it runs in the same coroutine)
may then issue the next request. In such a case, we will enter
curl_setup_preadv() effectively from within curl_read_cb().
Calling curl_multi_add_handle() will then fail and the new request will
not be processed.
Fix this by not letting curl_read_cb() wake up acb->co. Instead, leave
the whole business of settling the AIOCB objects to
curl_multi_check_completion() (which is called from our timer callback
and our FD handler, so not from any cURL callbacks).
Reported-by: Natalie Gavrielov <ngavrilo@redhat.com>
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1740193
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190910124136.10565-7-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Instead of reporting all sockets to cURL, only report the one that has
caused curl_multi_do_locked() to be called. This lets us get rid of the
QLIST_FOREACH_SAFE() list, which was actually wrong: SAFE foreaches are
only safe when the current element is removed in each iteration. If it
possible for the list to be concurrently modified, we cannot guarantee
that only the current element will be removed. Therefore, we must not
use QLIST_FOREACH_SAFE() here.
Fixes: ff5ca1664a
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190910124136.10565-6-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
curl_multi_do_locked() currently marks all sockets as ready. That is
not only inefficient, but in fact unsafe (the loop is). A follow-up
patch will change that, but to do so, curl_multi_do_locked() needs to
know exactly which socket is ready; and that is accomplished by this
patch here.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190910124136.10565-5-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
While it is more likely that transfers complete after some file
descriptor has data ready to read, we probably should not rely on it.
Better be safe than sorry and call curl_multi_check_completion() in
curl_multi_do(), too, just like it is done in curl_multi_read().
With this change, curl_multi_do() and curl_multi_read() are actually the
same, so drop curl_multi_read() and use curl_multi_do() as the sole FD
handler.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190910124136.10565-4-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This does not really change anything, but it makes the code a bit easier
to follow once we use @socket as the opaque pointer for
aio_set_fd_handler().
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190910124136.10565-3-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
A follow-up patch will make curl_multi_do() and curl_multi_read() take a
CURLSocket instead of the CURLState. They still need the latter,
though, so add a pointer to it to the former.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190910124136.10565-2-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Replace instances of:
(n & (BDRV_SECTOR_SIZE - 1)) == 0
And:
(n & ~BDRV_SECTOR_MASK) == 0
With:
QEMU_IS_ALIGNED(n, BDRV_SECTOR_SIZE)
Which reveals the intent of the code better, and makes it easier to
locate the code checking alignment.
Signed-off-by: Nir Soffer <nsoffer@redhat.com>
Message-id: 20190827185913.27427-2-nsoffer@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
handle_alloc() tries to find as many contiguous clusters that need
copy-on-write as possible in order to allocate all of them at the same
time.
However, compressed clusters are only overwritten one by one, so let's
say that we have an image with 1024 consecutive compressed clusters:
qemu-img create -f qcow2 hd.qcow2 64M
for f in `seq 0 64 65472`; do
qemu-io -c "write -c ${f}k 64k" hd.qcow2
done
In this case trying to overwrite the whole image with one large write
request results in 1024 separate allocations:
qemu-io -c "write 0 64M" hd.qcow2
This restriction comes from commit 095a9c58ce from 2008.
Nowadays QEMU can overwrite multiple compressed clusters just fine,
and in fact it already does: as long as the first cluster that
handle_alloc() finds is not compressed, all other compressed clusters
in the same batch will be overwritten in one go:
qemu-img create -f qcow2 hd.qcow2 64M
qemu-io -c "write -z 0 64k" hd.qcow2
for f in `seq 64 64 65472`; do
qemu-io -c "write -c ${f}k 64k" hd.qcow2
done
Compared to the previous one, overwriting this image on my computer
goes from 8.35s down to 230ms.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: John Snow <jsnow@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The 'blockdev-create' QMP command was introduced as experimental
feature in commit b0292b851b, using the assert() debug call.
It got promoted to 'stable' command in 3fb588a0f2, but the
assert call was not removed.
Some block drivers are optional, and bdrv_find_format() might
return a NULL value, triggering the assertion.
Stable code is not expected to abort, so return an error instead.
This is easily reproducible when libnfs is not installed:
./configure
[...]
module support no
Block whitelist (rw)
Block whitelist (ro)
libiscsi support yes
libnfs support no
[...]
Start QEMU:
$ qemu-system-x86_64 -S -qmp unix:/tmp/qemu.qmp,server,nowait
Send the 'blockdev-create' with the 'nfs' driver:
$ ( cat << 'EOF'
{'execute': 'qmp_capabilities'}
{'execute': 'blockdev-create', 'arguments': {'job-id': 'x', 'options': {'size': 0, 'driver': 'nfs', 'location': {'path': '/', 'server': {'host': '::1', 'type': 'inet'}}}}, 'id': 'x'}
EOF
) | socat STDIO UNIX:/tmp/qemu.qmp
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 1, "major": 4}, "package": "v4.1.0-733-g89ea03a7dc"}, "capabilities": ["oob"]}}
{"return": {}}
QEMU crashes:
$ gdb qemu-system-x86_64 core
Program received signal SIGSEGV, Segmentation fault.
(gdb) bt
#0 0x00007ffff510957f in raise () at /lib64/libc.so.6
#1 0x00007ffff50f3895 in abort () at /lib64/libc.so.6
#2 0x00007ffff50f3769 in _nl_load_domain.cold.0 () at /lib64/libc.so.6
#3 0x00007ffff5101a26 in .annobin_assert.c_end () at /lib64/libc.so.6
#4 0x0000555555d7e1f1 in qmp_blockdev_create (job_id=0x555556baee40 "x", options=0x555557666610, errp=0x7fffffffc770) at block/create.c:69
#5 0x0000555555c96b52 in qmp_marshal_blockdev_create (args=0x7fffdc003830, ret=0x7fffffffc7f8, errp=0x7fffffffc7f0) at qapi/qapi-commands-block-core.c:1314
#6 0x0000555555deb0a0 in do_qmp_dispatch (cmds=0x55555645de70 <qmp_commands>, request=0x7fffdc005c70, allow_oob=false, errp=0x7fffffffc898) at qapi/qmp-dispatch.c:131
#7 0x0000555555deb2a1 in qmp_dispatch (cmds=0x55555645de70 <qmp_commands>, request=0x7fffdc005c70, allow_oob=false) at qapi/qmp-dispatch.c:174
With this patch applied, QEMU returns a QMP error:
{'execute': 'blockdev-create', 'arguments': {'job-id': 'x', 'options': {'size': 0, 'driver': 'nfs', 'location': {'path': '/', 'server': {'host': '::1', 'type': 'inet'}}}}, 'id': 'x'}
{"id": "x", "error": {"class": "GenericError", "desc": "Block driver 'nfs' not found or not supported"}}
Cc: qemu-stable@nongnu.org
Reported-by: Xu Tian <xutian@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
libnfs recently added support for unmounting. Add support
in Qemu too.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
nfs_close is a sync call from libnfs and has its own event
handler polling on the nfs FD. Avoid that both QEMU and libnfs
are intefering here.
CC: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
blockdev_create_run() directly uses .bdrv_co_create()'s return value as
the job's return value. Jobs must return 0 on success, not just any
nonnegative value. Therefore, using blockdev-create for VPC images may
currently fail as the vpc driver may return a positive integer.
Because there is no point in returning a positive integer anywhere in
the block layer (all non-negative integers are generally treated as
complete success), we probably do not want to add more such cases.
Therefore, fix this problem by making the vpc driver always return 0 in
case of success.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If QEMU_AIO_NO_FALLBACK is given, we always return failure and don't
even try to use the BLKZEROOUT ioctl. In this failure case, we shouldn't
disable has_write_zeroes because we didn't learn anything about the
ioctl. The next request might not set QEMU_AIO_NO_FALLBACK and we can
still use the ioctl then.
Fixes: 738301e117
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This patch removes xfs_write_zeroes() and xfs_discard(). Both functions
have been added just before the same feature was present through
fallocate():
- fallocate() has supported PUNCH_HOLE for XFS since Linux 2.6.38 (March
2011); xfs_discard() was added in December 2010.
- fallocate() has supported ZERO_RANGE for XFS since Linux 3.15 (June
2014); xfs_write_zeroes() was added in November 2013.
Nowadays, all systems that qemu runs on should support both fallocate()
features (RHEL 7's kernel does).
xfsctl() is still useful for getting the request alignment for O_DIRECT,
so this patch does not remove our dependency on it completely.
Note that xfs_write_zeroes() had a bug: It calls ftruncate() when the
file is shorter than the specified range (because ZERO_RANGE does not
increase the file length). ftruncate() may yield and then discard data
that parallel write requests have written past the EOF in the meantime.
Dropping the function altogether fixes the bug.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Fixes: 50ba5b2d99
Reported-by: Lukáš Doktor <ldoktor@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Tested-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
In job_finish_sync job_enter should be enough for a job to make some
progress and draining is a wrong tool for it. So use job_enter directly
here and drop job_drain with all related staff not used more.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The size of the qcow2 L2 cache defaults to 32 MB, which can be easily
larger than the maximum amount of L2 metadata that the image can have.
For example: with 64 KB clusters the user would need a qcow2 image
with a virtual size of 256 GB in order to have 32 MB of L2 metadata.
Because of that, since commit b749562d98
we forbid the L2 cache to become larger than the maximum amount of L2
metadata for the image, calculated using this formula:
uint64_t max_l2_cache = virtual_disk_size / (s->cluster_size / 8);
The problem with this formula is that the result should be rounded up
to the cluster size because an L2 table on disk always takes one full
cluster.
For example, a 1280 MB qcow2 image with 64 KB clusters needs exactly
160 KB of L2 metadata, but we need 192 KB on disk (3 clusters) even if
the last 32 KB of those are not going to be used.
However QEMU rounds the numbers down and only creates 2 cache tables
(128 KB), which is not enough for the image.
A quick test doing 4KB random writes on a 1280 MB image gives me
around 500 IOPS, while with the correct cache size I get 16K IOPS.
Cc: qemu-stable@nongnu.org
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The client side is fairly straightforward: if the server advertised
fast zero support, then we can map that to BDRV_REQ_NO_FALLBACK
support. A server that advertises FAST_ZERO but not WRITE_ZEROES
is technically broken, but we can ignore that situation as it does
not change our behavior.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190823143726.27062-4-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Revert the commit 118f99442d 'block/io.c: fix for the allocation failure'
and use better error handling for file systems that do not support
fallocate() for an unaligned byte range. Allow falling back to pwrite
in case fallocate() returns EINVAL.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Andrey Shinkevich <andrey.shinkevich@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Message-Id: <1566913973-15490-1-git-send-email-andrey.shinkevich@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Thanks to our recent move to use glib's g_autofree, I can join the
bandwagon. Getting rid of gotos is fun ;)
There are probably more places where we could register cleanup
functions and get rid of more gotos; this patch just focuses on the
labels that existed merely to call g_free.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20190824172813.29720-2-eblake@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Compressed writes generally have to write full clusters, not just in
theory but also in practice when it comes to vmdk's streamOptimized
subformat. It currently is just silently broken for writes with
non-zero in-cluster offsets:
$ qemu-img create -f vmdk -o subformat=streamOptimized foo.vmdk 1M
$ qemu-io -c 'write 4k 4k' -c 'read 4k 4k' foo.vmdk
wrote 4096/4096 bytes at offset 4096
4 KiB, 1 ops; 00.01 sec (443.724 KiB/sec and 110.9309 ops/sec)
read failed: Invalid argument
(The technical reason is that vmdk_write_extent() just writes the
incomplete compressed data actually to offset 4k. When reading the
data, vmdk_read_extent() looks at offset 0 and finds the compressed data
size to be 0, because that is what it reads from there. This yields an
error.)
For incomplete writes with zero in-cluster offsets, the error path when
reading the rest of the cluster is a bit different, but the result is
the same:
$ qemu-img create -f vmdk -o subformat=streamOptimized foo.vmdk 1M
$ qemu-io -c 'write 0k 4k' -c 'read 4k 4k' foo.vmdk
wrote 4096/4096 bytes at offset 0
4 KiB, 1 ops; 00.01 sec (362.641 KiB/sec and 90.6603 ops/sec)
read failed: Invalid argument
(Here, vmdk_read_extent() finds the data and then sees that the
uncompressed data is short.)
It is better to reject invalid writes than to make the user believe they
might have succeeded and then fail when trying to read it back.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20190815153638.4600-5-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This makes iotest 033 pass with e.g. subformat=monolithicFlat. It also
turns a former error in 059 into success.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190815153638.4600-3-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When creating an image with preallocation "off" or "falloc", the first
block of the image is typically not allocated. When using Gluster
storage backed by XFS filesystem, reading this block using direct I/O
succeeds regardless of request length, fooling alignment detection.
In this case we fallback to a safe value (4096) instead of the optimal
value (512), which may lead to unneeded data copying when aligning
requests. Allocating the first block avoids the fallback.
Since we allocate the first block even with preallocation=off, we no
longer create images with zero disk size:
$ ./qemu-img create -f raw test.raw 1g
Formatting 'test.raw', fmt=raw size=1073741824
$ ls -lhs test.raw
4.0K -rw-r--r--. 1 nsoffer nsoffer 1.0G Aug 16 23:48 test.raw
And converting the image requires additional cluster:
$ ./qemu-img measure -f raw -O qcow2 test.raw
required size: 458752
fully allocated size: 1074135040
When using format like vmdk with multiple files per image, we allocate
one block per file:
$ ./qemu-img create -f vmdk -o subformat=twoGbMaxExtentFlat test.vmdk 4g
Formatting 'test.vmdk', fmt=vmdk size=4294967296 compat6=off hwversion=undefined subformat=twoGbMaxExtentFlat
$ ls -lhs test*.vmdk
4.0K -rw-r--r--. 1 nsoffer nsoffer 2.0G Aug 27 03:23 test-f001.vmdk
4.0K -rw-r--r--. 1 nsoffer nsoffer 2.0G Aug 27 03:23 test-f002.vmdk
4.0K -rw-r--r--. 1 nsoffer nsoffer 353 Aug 27 03:23 test.vmdk
I did quick performance test for copying disks with qemu-img convert to
new raw target image to Gluster storage with sector size of 512 bytes:
for i in $(seq 10); do
rm -f dst.raw
sleep 10
time ./qemu-img convert -f raw -O raw -t none -T none src.raw dst.raw
done
Here is a table comparing the total time spent:
Type Before(s) After(s) Diff(%)
---------------------------------------
real 530.028 469.123 -11.4
user 17.204 10.768 -37.4
sys 17.881 7.011 -60.7
We can see very clear improvement in CPU usage.
Signed-off-by: Nir Soffer <nsoffer@redhat.com>
Message-id: 20190827010528.8818-2-nsoffer@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Implement and use new interface to get rid of hd_qiov.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-13-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-13-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Implement and use new interface to get rid of hd_qiov.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-12-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-12-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Use buffer based io in encrypted case.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-11-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-11-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Introduce extended variants of bdrv_co_preadv and bdrv_co_pwritev
with qiov_offset parameter.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-10-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-10-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Use and support new API in bdrv_aligned_pwritev.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-9-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-9-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Use and support new API in bdrv_co_do_copy_on_readv.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-8-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-8-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allocate bounce_buffer only if it is really needed. Also, sub-optimize
allocation size (why not?).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-7-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-7-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Use and support new API in bdrv_co_do_copy_on_readv. Note that in case
of allocated-in-top we need to shrink read size to MIN(..) by hand, as
pre-patch this was actually done implicitly by qemu_iovec_concat (and
we used local_qiov.size).
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-6-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-6-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add handlers supporting qiov_offset parameter:
bdrv_co_preadv_part
bdrv_co_pwritev_part
bdrv_co_pwritev_compressed_part
This is used to reduce need of defining local_qiovs and hd_qiovs in all
corners of block layer code. The following patches will increase usage
of this new API part by part.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-5-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-5-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We have similar padding code in bdrv_co_pwritev,
bdrv_co_do_pwrite_zeroes and bdrv_co_preadv. Let's combine and unify
it.
[Squashed in Vladimir's qemu-iotests 077 fix
--Stefan]
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-4-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-4-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We'll need to check a part of qiov soon, so implement it now.
Optimization with align down to 4 * sizeof(long) is dropped due to:
1. It is strange: it aligns length of the buffer, but where is a
guarantee that buffer pointer is aligned itself?
2. buffer_is_zero() is a better place for optimizations and it has
them.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190604161514.262241-3-vsementsov@virtuozzo.com
Message-Id: <20190604161514.262241-3-vsementsov@virtuozzo.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
vpc is not really a passthrough driver, even when using the fixed
subformat (where host and guest offsets are equal). It should handle
preallocation like all other drivers do, namely by returning
DATA | RECURSE instead of RAW.
There is no tangible difference but the fact that bdrv_is_allocated() no
longer falls through to the protocol layer.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190725155512.9827-4-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Fixes: 69f47505ee
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190725155512.9827-3-mreitz@redhat.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Fixes: 69f47505ee
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190725155512.9827-2-mreitz@redhat.com
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Fixed VHDX images cannot guarantee to be zero-initialized. If the image
has the "fixed" subformat, forward the call to the underlying storage
node.
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190724171239.8764-9-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Static VDI images cannot guarantee to be zero-initialized. If the image
has been statically allocated, forward the call to the underlying
storage node.
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Tested-by: Stefano Garzarella <sgarzare@redhat.com>
Message-id: 20190724171239.8764-8-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
If a qcow2 file is preallocated, it can no longer guarantee that it
initially appears as filled with zeroes.
So implement .bdrv_has_zero_init() by checking whether the file is
preallocated; if so, forward the call to the underlying storage node,
except for when it is encrypted: Encrypted preallocated images always
return effectively random data, so .bdrv_has_zero_init() must always
return 0 for them.
.bdrv_has_zero_init_truncate() can remain bdrv_has_zero_init_1(),
because it presupposes PREALLOC_MODE_OFF.
Reported-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190724171239.8764-7-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
vhdx and parallels call bdrv_has_zero_init() when they do not really
care about an image's post-create state but only about what happens when
you grow an image. That is a bit ugly, and also overly safe when
growing preallocated images without preallocating the new areas.
Let them use bdrv_has_zero_init_truncate() instead.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190724171239.8764-6-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
[mreitz: Added commit message]
Signed-off-by: Max Reitz <mreitz@redhat.com>
We need to implement .bdrv_has_zero_init_truncate() for every block
driver that supports truncation and has a .bdrv_has_zero_init()
implementation.
Implement it the same way each driver implements .bdrv_has_zero_init().
This is at least not any more unsafe than what we had before.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190724171239.8764-5-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
bdrv_has_zero_init() only has meaning for newly created images or image
areas. If the mirror job itself did not create the image, it cannot
rely on bdrv_has_zero_init()'s result to carry any meaning.
This is the case for drive-mirror with mode=existing and always for
blockdev-mirror.
Note that we only have to zero-initialize the target with sync=full,
because other modes actually do not promise that the target will contain
the same data as the source after the job -- sync=top only promises to
copy anything allocated in the top layer, and sync=none will only copy
new I/O. (Which is how mirror has always handled it.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190724171239.8764-3-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Opening a block device on NetBSD has an additional step compared to other OSes,
corresponding to raw_normalize_devicepath. The error message in that function
is slightly different from that in raw_open_common and this was causing spurious
failures in qemu-iotests. However, in general it is not important to know what
exact step was failing, for example in the qemu-iotests case the error message
contains the fairly unequivocal "No such file or directory" text from strerror.
We can thus fix the failures by standardizing on a single error message for
both raw_open_common and raw_normalize_devicepath; in fact, we can even
use error_setg_file_open to make sure the error message is the same as in
the rest of QEMU.
Message-Id: <20190725095920.28419-1-pbonzini@redhat.com>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
write flags are constant, let's store it in BackupBlockJob instead of
recalculating. It also makes two boolean fields to be unused, so,
drop them.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190730163251.755248-4-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
We have detect_zeroes option, so at least for blockdev-backup user
should define it if zero-detection is needed. For drive-backup leave
detection enabled by default but do it through existing option instead
of open-coding.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190730163251.755248-2-vsementsov@virtuozzo.com
Signed-off-by: John Snow <jsnow@redhat.com>
Let's add a possibility to query dirty-bitmaps not only on root nodes.
It is useful when dealing both with snapshots and incremental backups.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20190717173937.18747-1-jsnow@redhat.com
[Added deprecation information. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
[Fixed spelling --js]
Accept bitmaps and sync policies for the other backup modes.
This allows us to do things like create a bitmap synced to a full backup
without a transaction, or start a resumable backup process.
Some combinations don't make sense, though:
- NEVER policy combined with any non-BITMAP mode doesn't do anything,
because the bitmap isn't used for input or output.
It's harmless, but is almost certainly never what the user wanted.
- sync=NONE is more questionable. It can't use on-success because this
job never completes with success anyway, and the resulting artifact
of 'always' is suspect: because we start with a full bitmap and only
copy out segments that get written to, the final output bitmap will
always be ... a fully set bitmap.
Maybe there's contexts in which bitmaps make sense for sync=none,
but not without more severe changes to the current job, and omitting
it here doesn't prevent us from adding it later.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190716000117.25219-11-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Presently, If sync=TOP is selected, we mark the entire bitmap as dirty.
In the write notifier handler, we dutifully copy out such regions.
Fix this in three parts:
1. Mark the bitmap as being initialized before the first yield.
2. After the first yield but before the backup loop, interrogate the
allocation status asynchronously and initialize the bitmap.
3. Teach the write notifier to interrogate allocation status if it is
invoked during bitmap initialization.
As an effect of this patch, the job progress for TOP backups
now behaves like this:
- total progress starts at bdrv_length.
- As allocation status is interrogated, total progress decreases.
- As blocks are copied, current progress increases.
Taken together, the floor and ceiling move to meet each other.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 20190716000117.25219-10-jsnow@redhat.com
[Remove ret = -ECANCELED change. --js]
[Squash in conflict resolution based on Max's patch --js]
Message-id: c8b0ab36-79c8-0b4b-3193-4e12ed8c848b@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Modify bdrv_is_unallocated_range to utilize the pnum return from
bdrv_is_allocated, and in the process change the semantics from
"is unallocated" to "is allocated."
Optionally returns a full number of clusters that share the same
allocation status.
This will be used to carefully toggle bits in the bitmap for sync=top
initialization in the following commits.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190716000117.25219-9-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Just a few housekeeping changes that keeps the following commit easier
to read; perform the initial copy_bitmap initialization in one place.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190716000117.25219-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
When making backups based on bitmaps, the work estimate can be more
accurate. Update iotests to reflect the new strategy.
TOP work estimates are broken, but do not get worse with this commit.
That issue is addressed in the following commits instead.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190716000117.25219-7-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This is nicer to do in the unified QMP interface that we have now,
because it lets us use the right terminology back at the user.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190716000117.25219-5-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
It is used to do transactional movement of the bitmap (which is
possible in conjunction with merge command). Transactional bitmap
movement is needed in scenarios with external snapshot, when we don't
want to leave copy of the bitmap in the base image.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190708220502.12977-3-jsnow@redhat.com
[Edited "since" version to 4.2 --js]
Signed-off-by: John Snow <jsnow@redhat.com>
With the "never" sync policy, we actually can utilize readonly bitmaps
now. Loosen the check at the QMP level, and tighten it based on
provided arguments down at the job creation level instead.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-19-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This adds an "always" policy for bitmap synchronization. Regardless of if
the job succeeds or fails, the bitmap is *always* synchronized. This means
that for backups that fail part-way through, the bitmap retains a record of
which sectors need to be copied out to accomplish a new backup using the
old, partial result.
In effect, this allows us to "resume" a failed backup; however the new backup
will be from the new point in time, so it isn't a "resume" as much as it is
an "incremental retry." This can be useful in the case of extremely large
backups that fail considerably through the operation and we'd like to not waste
the work that was already performed.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-13-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This simplifies some interface matters; namely the initialization and
(later) merging the manifest back into the sync_bitmap if it was
provided.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-12-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Add a public interface for get. While we're at it,
rename "bdrv_get_dirty_bitmap_locked" to "bdrv_dirty_bitmap_get_locked".
(There are more functions to rename to the bdrv_dirty_bitmap_VERB form,
but they will wait until the conclusion of this series.)
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-11-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
I'm surprised it didn't come up sooner, but sometimes we have a +busy
bitmap as a source. This is dangerous from the QMP API, but if we are
the owner that marked the bitmap busy, it's safe to merge it using it as
a read only source.
It is not safe in the general case to allow users to read from in-use
bitmaps, so create an internal variant that foregoes the safety
checking.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-10-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This adds a "never" policy for bitmap synchronization. Regardless of if
the job succeeds or fails, we never update the bitmap. This can be used
to perform differential backups, or simply to avoid the job modifying a
bitmap.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-7-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
We don't need or want a new sync mode for simple differences in
semantics. Create a new mode simply named "BITMAP" that is designed to
make use of the new Bitmap Sync Mode field.
Because the only bitmap sync mode is 'on-success', this adds no new
functionality to the backup job (yet). The old incremental backup mode
is maintained as a syntactic sugar for sync=bitmap, mode=on-success.
Add all of the plumbing necessary to support this new instruction.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190709232550.10724-6-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
- file-posix: Fix O_DIRECT alignment detection
- Fixes for concurrent block jobs
- block-backend: Queue requests while drained (fix IDE vs. job crashes)
- qemu-img convert: Deprecate using -n and -o together
- iotests: Migration tests with filter nodes
- iotests: More media change tests
-----BEGIN PGP SIGNATURE-----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=T7L5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- file-posix: Fix O_DIRECT alignment detection
- Fixes for concurrent block jobs
- block-backend: Queue requests while drained (fix IDE vs. job crashes)
- qemu-img convert: Deprecate using -n and -o together
- iotests: Migration tests with filter nodes
- iotests: More media change tests
# gpg: Signature made Fri 16 Aug 2019 10:29:18 BST
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
file-posix: Handle undetectable alignment
qemu-img convert: Deprecate using -n and -o together
block-backend: Queue requests while drained
mirror: Keep mirror_top_bs drained after dropping permissions
block: Remove blk_pread_unthrottled()
iotests: Add test for concurrent stream/commit
tests: Test mid-drain bdrv_replace_child_noperm()
tests: Test polling in bdrv_drop_intermediate()
block: Reduce (un)drains when replacing a child
block: Keep subtree drained in drop_intermediate
block: Simplify bdrv_filter_default_perms()
iotests: Test migration with all kinds of filter nodes
iotests: Move migration helpers to iotests.py
iotests/118: Add -blockdev based tests
iotests/118: Create test classes dynamically
iotests/118: Test media change for scsi-cd
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
