VCAP is a register for devices with energy storage capacitors.
Reviewed-by: Benjamin Streb <bstreb@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-4-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PMBus devices may integrate fans whose operation is configurable
over PMBus. This commit allows the driver to read and write the
fan control registers but does not model the operation of fans.
Reviewed-by: Stephen Longfield <slongfield@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-3-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The VOUT_MODE command is described in the PMBus Specification,
Part II, Ver 1.3 Section 8.3
VOUT_MODE has a three bit mode and 4 bit parameter, the three bit
mode determines whether voltages are formatted as uint16, uint16,
VID, and Direct modes. VID and Direct modes use the remaining 5 bits
to scale the voltage readings.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-2-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
PMBus devices can send and receive variable length data using the
block read and write format, with the first byte in the payload
denoting the length.
This is mostly used for strings and on-device logs. Devices can
respond to a block read with an empty string.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-ID: <20231023-staging-pmbus-v3-v4-1-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
-----BEGIN PGP SIGNATURE-----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=ymmX
-----END PGP SIGNATURE-----
Merge tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu into staging
aspeed queue:
* Fixes for the Aspeed I2C model
* New SDK image for avocado tests
* blockdev support for flash device definition
* SD refactoring preparing ground for eMMC support
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmTxsaQACgkQUaNDx8/7
# 7KGXmg//XJNisscl/VWSBaGmH5MbQUAg/QCRalXx1V/lJ8rhE/JqwnWKuoPFd4EN
# iDlh3ufpzxPhHFc9boechuM5ytlrJxpLJoCIJ4sw/4qnO3Dy3Q6BCy1t8Ma62D1u
# oE7cAMHsriJ1uTJNHUTFo72VapTaH2XwFN9lFDuQW45d+WWAXtVJsqvRgFETNmw6
# YYnTTpH2gLTZZFEgOixhWpGLh4Ibc/l8U1VzL0ctQmC11xng0bqk3PAqU9NGzcM5
# MJmEGAxg43CnFu9NJI1nMqC/coi/8PFtrM7HprSwE3H8Jkwncs4ePVT+kZQC+VNQ
# 7EaVkksfEGHlN8XP5+eQDrQ5yT6ve+fbHTLQhwULfeyt0GlQ8h1yewvHCDWo/zw3
# XI1ZyOcNZ2yiaenSUrTPzu0LiqZEJQnzRjPCpgTi1fU08ryEMEaPtr176YDLCguQ
# cpRj4QSZHCrGl/Eo9NlkFP/2rQDKTvCcedKPkYLQtsurSiH/36Oj9YvZycNtZ574
# ortKAtru4YV/rglNX4L8JDhdI+nqvy1liifpJsiS/2KBZDpVFaP8PzGIV40HNy3G
# 8/LVTnaggZaScF3ftHhkg84uQumELS9l2dhsNCL9HqdlrNXLQrVAIR6iuQlpOKBa
# 5S/6h7ZXGOb1qNVQjYp4HCrB7X1KIJYksZ3GdUREf8ot5Ds1FhE=
# =ymmX
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 01 Sep 2023 05:40:52 EDT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [unknown]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20230901' of https://github.com/legoater/qemu: (26 commits)
hw/sd: Introduce a "sd-card" SPI variant model
hw/sd: Add sd_cmd_SET_BLOCK_COUNT() handler
hw/sd: Add sd_cmd_SEND_TUNING_BLOCK() handler
hw/sd: Add sd_cmd_SEND_RELATIVE_ADDR() handler
hw/sd: Add sd_cmd_ALL_SEND_CID() handler
hw/sd: Add sd_cmd_SEND_OP_CMD() handler
hw/sd: Add sd_cmd_GO_IDLE_STATE() handler
hw/sd: Add sd_cmd_unimplemented() handler
hw/sd: Add sd_cmd_illegal() handler
hw/sd: Introduce sd_cmd_handler type
hw/sd: Move proto_name to SDProto structure
hw/sd: When card is in wrong state, log which spec version is used
hw/sd: When card is in wrong state, log which state it is
hw/sd/sdcard: Return ILLEGAL for CMD19/CMD23 prior SD spec v3.01
aspeed: Get the BlockBackend of FMC0 from the flash device
m25p80: Introduce an helper to retrieve the BlockBackend of a device
aspeed: Create flash devices only when defaults are enabled
hw/ssi: Check for duplicate CS indexes
aspeed/smc: Wire CS lines at reset
hw/ssi: Introduce a ssi_get_cs() helper
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Added support for the buffer organization option in pool buffer control
register.when set to 1,The buffer is split into two parts: Lower 16 bytes
for Tx and higher 16 bytes for Rx.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Fixed inconsistency between the regisiter bit field definition header file
and the ast2600 datasheet. The reg name is I2CD1C:Pool Buffer Control
Register in old register mode and I2CC0C: Master/Slave Pool Buffer Control
Register in new register mode. They share bit field
[12:8]:Transmit Data Byte Count and bit field
[29:24]:Actual Received Pool Buffer Size according to the datasheet.
According to the ast2600 datasheet,the actual Tx count is
Transmit Data Byte Count plus 1, and the max Rx size is
Receive Pool Buffer Size plus 1, both in Pool Buffer Control Register.
The version before forgot to plus 1, and mistake Rx count for Rx size.
Signed-off-by: Hang Yu <francis_yuu@stu.pku.edu.cn>
Fixes: 3be3d6ccf2 ("aspeed: i2c: Migrate to registerfields API")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Message-ID: <20230823065335.1919380-14-mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add read and write functions for accessing registers of I2C devices
connected to the Aspeed I2C controller.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Ninad Palsule <ninad@linux.ibm.com>
Message-Id: <20230331173051.3857801-2-stefanb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It is not given that the current master will release the bus after a
transfer ends. Only schedule a pending master if the bus is idle.
Fixes: 37fa5ca426 ("hw/i2c: support multiple masters")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20221116084312.35808-2-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to rename TYPE_VERSATILE_I2C as TYPE_ARM_SBCON_I2C
(the formal ARM naming), start renaming its state.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230110082508.24038-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define TYPE_GPIO_I2C in the public "hw/i2c/bitbang_i2c.h"
header and use it in hw/arm/musicpal.c.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20230111085016.44551-2-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NPCM7XX models have been commited after the conversion from
commit 8063396bf3 ("Use OBJECT_DECLARE_SIMPLE_TYPE when possible").
Manually convert them.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20230109140306.23161-11-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Allwinner TWI/I2C controller emulation. Only
master-mode functionality is implemented.
The SPL boot for Cubieboard expects AXP209 PMIC on TWI0/I2C0 bus, so this is
first part enabling the TWI/I2C bus operation.
Since both Allwinner A10 and H3 use the same module, it is added for
both boards.
Docs are also updated for Cubieboard and Orangepi-PC board to indicate
I2C availability.
Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20221226220303.14420-4-strahinja.p.jankovic@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I think when Klaus ported his slave mode changes from the original patch
series to the rewritten I2C module, he changed the behavior of the first
byte that is received by the slave device.
What's supposed to happen is that the AspeedI2CBus's slave device's
i2c_event callback should run, and if the event is "send_async", then it
should populate the byte buffer with the 8-bit I2C address that is being
sent to. Since we only support "send_async", the lowest bit should
always be 0 (indicating that the master is requesting to send data).
This is the code Klaus had previously, for reference. [1]
switch (event) {
case I2C_START_SEND:
bus->buf = bus->dev_addr << 1;
bus->buf &= I2CD_BYTE_BUF_RX_MASK;
bus->buf <<= I2CD_BYTE_BUF_RX_SHIFT;
bus->intr_status |= (I2CD_INTR_SLAVE_ADDR_RX_MATCH | I2CD_INTR_RX_DONE);
aspeed_i2c_set_state(bus, I2CD_STXD);
break;
[1]: https://lore.kernel.org/qemu-devel/20220331165737.1073520-4-its@irrelevant.dk/
Fixes: a8d48f59cd ("hw/i2c/aspeed: add slave device in old register mode")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220820225712.713209-2-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Titus Rwantare <titusr@google.com>
Message-Id: <20220701000626.77395-2-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This commit adds support for DMA RX in slave mode while using the new
register set in the AST2600 and AST1030. This patch also pretty much
assumes packet mode is enabled, I'm not sure if this will work in DMA
step mode.
This is particularly useful for testing IPMB exchanges between Zephyr
and external devices, which requires multi-master I2C support and DMA in
the new register mode, because the Zephyr drivers from Aspeed use DMA in
the new mode by default. The Zephyr drivers are also using packet mode.
The typical sequence of events for receiving data in DMA slave + packet
mode is that the Zephyr firmware will configure the slave address
register with an address to receive on and configure the bus's function
control register to enable master mode and slave mode simultaneously at
startup, before any transfers are initiated.
RX DMA is enabled in the slave mode command register, and the slave RX
DMA buffer address and slave RX DMA buffer length are set. TX DMA is not
covered in this patch.
When the Aspeed I2C controller receives data from some other I2C master,
it will reset the I2CS_DMA_LEN RX_LEN value to zero, then buffer
incoming data in the RX DMA buffer while incrementing the I2CC_DMA_ADDR
address counter and decrementing the I2CC_DMA_LEN counter. It will also
update the I2CS_DMA_LEN RX_LEN value along the way.
Once all the data has been received, the bus controller will raise an
interrupt indicating a packet command was completed, the slave address
matched, a normal stop condition was seen, and the transfer was an RX
operation.
If the master sent a NACK instead of a normal stop condition, or the
transfer timed out, then a slightly different set of interrupt status
values would be set. Those conditions are not handled in this commit.
The Zephyr firmware then collects data from the RX DMA buffer and clears
the status register by writing the PKT_MODE_EN bit to the status
register. In packet mode, clearing the packet mode interrupt enable bit
also clears most of the other interrupt bits automatically (except for a
few bits above it).
Note: if the master transmit or receive functions were in use
simultaneously with the slave mode receive functionality, then the
master mode functions may have raised the interrupt line for the bus
before the DMA slave transfer is complete. It's important to have the
slave's interrupt status register clear throughout the receive
operation, and if the slave attempts to raise the interrupt before the
master interrupt status is cleared, then it needs to re-raise the
interrupt once the master interrupt status is cleared. (And vice-versa).
That's why in this commit, when the master interrupt status is cleared
and the interrupt line is lowered, we call the slave interrupt _raise_
function, to see if the interrupt was pending. (And again, vice-versa).
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220630045133.32251-8-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add slave mode functionality for the Aspeed I2C controller in old
register mode. This is implemented by realizing an I2C slave device
owned by the I2C controller and attached to its own bus.
The I2C slave device only implements asynchronous sends on the bus, so
slaves not supporting that will not be able to communicate with it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: checkpatch fixes ]
Message-Id: <20220601210831.67259-6-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-7-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add an asynchronous version of i2c_send() that requires the slave to
explicitly acknowledge on the bus with i2c_ack().
The current master must use the new i2c_start_send_async() to indicate
that it wants to do an asynchronous transfer. This allows the i2c core
to check if the target slave supports this or not. This approach relies
on adding a new enum i2c_event member, which is why a bunch of other
devices needs changes in their event handling switches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20220601210831.67259-5-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-6-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Allow slaves to master the bus by registering a bottom halve. If the bus
is busy, the bottom half is queued up. When a slave has succesfully
mastered the bus, the bottom half is scheduled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg : - fixed typos in commit log ]
Message-Id: <20220601210831.67259-4-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220630045133.32251-5-me@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add support for writing and reading the device address register in old
register mode.
On the AST2400 (only 1 slave address)
* no upper bits
On the AST2500 (2 possible slave addresses),
* bit[31] : Slave Address match indicator
* bit[30] : Slave Address Receiving pending
On the AST2600 (3 possible slave addresses),
* bit[31-30] : Slave Address match indicator
* bit[29] : Slave Address Receiving pending
The model could be more precise to take into account all fields but
since the Linux driver is masking the register value being set, it
should be fine. See commit 3fb2e2aeafb2 ("i2c: aspeed: disable
additional device addresses on ast2[56]xx") from Zeiv. This can be
addressed later.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
[ clg: add details to commit log ]
Message-Id: <20220601210831.67259-3-its@irrelevant.dk>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Moves register definitions and short commonly used inlined functiosn to
the header file to help tidy up the implementation file.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I34dff7485b6bbe3c9482715ccd94dbd65dc5f324
Message-Id: <20220331043248.2237838-8-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On AST2600, I2C has a secondary mode, called "new mode", which changes
the layout of registers, adds some minor behavior changes, and
introduces a new way to transfer data called "packet mode".
Most of the bit positions of the fields are the same between old and new
mode, so we use SHARED_FIELD_XX macros to reuse most of the code between
the different modes.
For packet mode, most of the command behavior is the same compared to
other modes, but there are some minor changes to how interrupts are
handled compared to other modes.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: I072f8301964f623afc74af1fe50c12e5caef199e
Message-Id: <20220331043248.2237838-6-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Using a register array will allow us to represent old-mode and new-mode
I2C registers by using the same underlying register array, instead of
adding an entire new set of variables to represent new mode.
As part of this, we also do additional cleanup to use ARRAY_FIELD_
macros instead of FIELD_ macros on registers.
Signed-off-by: Joe Komlodi <komlodi@google.com>
Change-Id: Ib94996b17c361b8490c042b43c99d8abc69332e3
[ clg: use of memset in aspeed_i2c_bus_reset() ]
Message-Id: <20220331043248.2237838-5-komlodi@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Macros should be ALL_CAPS. Normalize the exception.
Done with scripts/clean-header-guards.pl.
include/hw/xen/interface/ and tools/virtiofsd/ left alone, because
these were imported from Xen and libfuse respectively.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-3-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20220506134911.2856099-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Change to generated file ebpf/rss.bpf.skeleton.h backed out]
- add the VOUT_MIN and STATUS_MFR registers
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-2-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To ease reviewing code using the I2C bus API, introduce the
i2c_start_recv() and i2c_start_send() helpers which don't
take the confusing 'is_recv' boolean argument.
Use these new helpers in the SMBus / AUX bus models.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Make the argument representing the direction of the transfer a
boolean type.
Rename the boolean argument as 'is_recv' to match i2c_recv_send().
Document the function prototype.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20200621145235.9E241745712@zero.eik.bme.hu>
[PMD: Split patch, added docstring]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
We replaced all the i2c_send_recv() calls by the clearer i2c_recv()
and i2c_send(), so we can remove this confusing API.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
lm832x_key_event() is specific go LM832x devices, not to the
I2C bus API. Move it out of "i2c.h" to a new header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To enable passing the current_devs field as a parameter, we need to use
a named struct type.
Tested: BMC firmware with i2c devices booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210412194522.664594-2-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
One of the goals of having less boilerplate on QOM declarations
is to avoid human error. Requiring an extra argument that is
never used is an opportunity for mistakes.
Remove the unused argument from OBJECT_DECLARE_TYPE and
OBJECT_DECLARE_SIMPLE_TYPE.
Coccinelle patch used to convert all users of the macros:
@@
declarer name OBJECT_DECLARE_TYPE;
identifier InstanceType, ClassType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_TYPE(InstanceType, ClassType,
- lowercase,
UPPERCASE);
@@
declarer name OBJECT_DECLARE_SIMPLE_TYPE;
identifier InstanceType, lowercase, UPPERCASE;
@@
OBJECT_DECLARE_SIMPLE_TYPE(InstanceType,
- lowercase,
UPPERCASE);
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200916182519.415636-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
