ibm,lrdr-capacity has a field to describe the maximum address in bytes
and therefore, the most memory that can be allocated to this guest. We
are using maxmem for this field, but instead should use the actual RAM
address corresponding to the end of hotplug region.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This reverts commit 0d63b2dd31.
This change was originally intended to correct the HPET behavior
in conjunction with Linux, however the behavior that it actually creates
is not compatible with the ioapic.c implementation; it used to be
compatible with KVM's own IOAPIC but it is not anymore.
Signed-off-by: Bill Paul <wpaul@windriver.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <201604051558.20070.wpaul@windriver.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This line has been added in commit ef74679a81 with
other initializations. However, scancode set 0 doesn't exist (only 1, 2, 3).
This works well as long as operating system is resetting keyboard, or overwriting
the current scancode set with the one it wants.
This fixes IBM 40p firmware, which doesn't bother sending KBD_CMD_RESET or KBD_CMD_SCANCODE.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1458714100-28885-1-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error paths after a successful qdev_create/pci_bus_new
should contain a object_unref/object_unparent.
pxb_dev_init_common() did not yet, so add it.
Signed-off-by: Wei Jiangang <weijg.fnst@cn.fujitsu.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Eliminating the reentrancy is actually a nice thing that we can do
with the API that Michael proposed, so let's make it first class.
This also hides the complex assign/set_handler conventions from
callers of virtio_queue_aio_set_host_notifier_handler, which in
fact was always called with assign=true.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In addition to handling IO in vcpu thread and in io thread, dataplane
introduces yet another mode: handling it by AioContext.
This reuses the same handler as previous modes, which triggers races as
these were not designed to be reentrant. Use a separate handler just
for aio, and disable regular handlers when dataplane is active.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In addition to handling IO in vcpu thread and in io thread, dataplane
introduces yet another mode: handling it by AioContext.
This reuses the same handler as previous modes, which triggers races as
these were not designed to be reentrant. Use a separate handler just
for aio, and disable regular handlers when dataplane is active.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In addition to handling IO in vcpu thread and in io thread, blk dataplane
introduces yet another mode: handling it by AioContext.
Currently, this reuses the same handler as previous modes,
which triggers races as these were not designed to be reentrant.
Add instead a separate handler just for aio; this will make
it possible to disable regular handlers when dataplane is active.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add two missing checks for s->dataplane_fenced. In one case, QEMU
would skip injecting an IRQ due to a write to an uninitialized
EventNotifier's file descriptor.
In the second case, the dataplane_disabled field was used by mistake;
in fact after fixing this occurrence it is completely unused.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We must not call virtio_blk_data_plane_notify if dataplane is
disabled: we would hit a segmentation fault in notify_guest_bh as
s->guest_notifier has not been setup and is NULL.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If before loading snapshot we had set the timer of statistics, then after
applying snapshot the expiry time would be irrelevant for the restored
state of the virtual clocks. A simple fix is just to restart the timer
after loading snapshot.
For the user it may look like a long delay of statistics update after switch
to the snapshot.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The i82801b11 bridge didn't have a vmsd and thus didn't send
any migration data, including that of its parent PCIBridge object.
The symptom being if the guest used any devices behind the bridge
the guest crashed (mostly with various interrupt related issues).
Note: This will cause migration from old qemus that used this device to
explicitly fail during migration as opposed to the guest crashing.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Suggested-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Entries are inserted in filename order instead of being
appended to the end in case sorting is enabled.
This will avoid any future issues of moving the file creation
around, it doesn't matter what order they are created now,
the will always be in filename order.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Added machine type handling for compatibility. This was
a fairly complex change, this will preserve the order of fw_cfg
for older versions no matter what order the firmware files
actually come in. A list is kept of the correct legacy order
and the entries will be inserted based upon their order in
the list. Except that some entries are ordered (in a specific
area of the list) based upon what order they appear on the
command line. Special handling is added for those entries.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
piix3_ide_xen_class_init is identical to piix3_ide_class_init
except it's buggy as it does not set exit and does not disable
hotplug properly.
Switch to the generic one.
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Teach PCI testdev to use fast MMIO when kvm makes it available.
Before:
mmio-wildcard-eventfd:pci-mem 2271
After:
mmio-wildcard-eventfd:pci-mem 1218
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Through CP_TX_OWN and CP_RX_OWN points to the same bit, we'd better use
CP_TX_OWN for tx descriptor handling.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Currently spapr doesn't support "aborting" hotplug of PCI
devices by allowing device_del to immediately remove the
device if we haven't signalled the presence of the device
to the guest.
In the past this wasn't an issue, since we always immediately
signalled device attach and simply relied on full guest-aware
add->remove path for device removal. However, as of 788d259,
we now defer signalling for PCI functions until function 0
is attached, so now we need to deal with these "abort" operations
for cases where a user hotplugs a non-0 function, then opts to
remove it prior hotplugging function 0. Currently they'd have to
reboot before the unplug completed. PCIe multifunction hotplug
does not have this requirement however, so from a management
implementation perspective it would be good to address this within
the same release as 788d259.
We accomplish this by simply adding a 'signalled' flag to track
whether a device hotplug event has been sent to the guest. If it
hasn't, we allow immediate removal under the assumption that the
guest will not be using the device. Devices present at boot/reset
time are also assumed to be 'signalled'.
For CPU/memory/etc, signalling will still happen immediately
as part of device_add, so only PCI functions should be affected.
Cc: bharata@linux.vnet.ibm.com
Cc: david@gibson.dropbear.id.au
Cc: sbhat@linux.vnet.ibm.com
Cc: qemu-ppc@nongnu.org
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[dwg: This fixes a regression where an incorrect hot-add of a non-zero
function can no longer be backed out until function 0 is added]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
From: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes the current AIL implementation for POWER8. The
interrupt vector address can be calculated directly from LPCR when the
exception is handled. The excp_prefix update becomes useless and we
can cleanup the H_SET_MODE hcall.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: Removed LPES0/1 handling for HV vs. !HV
Fixed LPCR_ILE case for POWERPC_EXCP_POWER8 ]
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
[dwg: This was written as a cleanup, but it also fixes a real bug
where setting an alternative interrupt location would not be
correctly migrated]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Wire up the CPU timer interrupts in the right order, with the
nonsecure physical timer on cntpnsirq, the hyp timer on cnthpirq,
and the secure physical timer on cntpsirq. (We did get the
virt timer right, at least.)
Reported-by: Antonio Huete Jiménez <tuxillo@quantumachine.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1458210790-6621-1-git-send-email-peter.maydell@linaro.org
Indicate that autonegotiation is complete in the MII BMSR. This fixes
networking on xtfpga platform in linux v4.5.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-12-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-11-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implements FSR register, it is used for busy waits.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-10-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds fast read and 4bytes commands family.
This work is based on Pawel Lenkow patch from v1.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-9-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the setting from the volatile cfg register to correctly
set the number of dummy cycles.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-8-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds both volatile and non volatile configuration registers
and commands to allow modify them. It is needed for proper handling
dummy cycles. Initialization of those registers and flash state
has been included as well.
Some of this registers are used by kernel.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Acked-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-7-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds only 4byte address mode (does not cover dummy cycles).
This mode is needed to access more than 16 MiB of flash.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-6-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Extend address mode allows to switch flash 16 MiB banks,
allowing user to access all flash sectors.
This access mode is used by u-boot.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-5-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Extend the width of the flags variable to support the already existing
(but unused) WR_1 flag, which is above the range of 8 bits.
This allows support of EEPROM emulation which requires the WR_1 feature.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-4-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-3-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1458719789-29868-2-git-send-email-marcin.krzeminski@nokia.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a problem for power button that it will not work if an early
system_powerdown request happens before guest gpio driver loads.
Fix this problem by using gpio_key.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1458221140-15232-3-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will be used by ARM virt machine as a power button.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1458221140-15232-2-git-send-email-zhaoshenglong@huawei.com
[PMM: Use hyphen rather than underscore in type names;
add a comment briefly describing what the device does]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Changes:
* add initial MIPS CPS support
* implement ITU block
* implement MAAR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJW+43VAAoJEFIRjjwLKdprLmoH/1iWT4WsUJDF+9KX7PpFANbQ
DT+QSDBJr6K+jCenLlqfvB30txS+NDRFzmW65J8hlawVOwhamg1X+pcQTbAYy0sm
Du3Wexye0uw5YKUmqK2oCrgLJCKm3AqsmraaITE8q1URlkrQpuOuzazlIx5UA+RW
RgF/DsPAlit8TkZMHwaVIOeXUl8vl8152fU26QvwOGAT6J3lV+lQJ+gMPGRSAWOw
dcuVGNOTV0g3+kzOWisiqZc/V0Wp2Yu5IPezEVkFjZ4iyTTpnR8gkzuTNebzoRZo
Zmws4mqaZAX6ijveevd+ueh5sR+AX+mFBunoXQVSSBvRFlqBcEEL2nrwb9wOUX4=
=Ns6n
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160329-2' into staging
MIPS patches 2016-03-29
Changes:
* add initial MIPS CPS support
* implement ITU block
* implement MAAR
# gpg: Signature made Wed 30 Mar 2016 09:27:01 BST using RSA key ID 0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
* remotes/lalrae/tags/mips-20160329-2: (21 commits)
target-mips: add MAAR, MAARI register
target-mips: use CP0_CHECK for gen_m{f|t}hc0
hw/mips/cps: enable ITU for multithreading processors
target-mips: make ITC Configuration Tags accessible to the CPU
target-mips: check CP0 enabled for CACHE instruction also in R6
hw/mips: implement ITC Storage - Bypass View
hw/mips: implement ITC Storage - P/V Sync and Try Views
hw/mips: implement ITC Storage - Empty/Full Sync and Try Views
hw/mips: implement ITC Storage - Control View
hw/mips: implement ITC Configuration Tags and Storage Cells
target-mips: enable CM GCR in MIPS64R6-generic CPU
hw/mips_malta: add CPS to Malta board
hw/mips_malta: move CPU creation to a separate function
hw/mips_malta: remove redundant irq and clock init
hw/mips_malta: remove CPUMIPSState from the write_bootloader()
hw/mips/cps: create CPC block inside CPS
hw/mips: add initial Cluster Power Controller support
hw/mips/cps: create GCR block inside CPS
hw/mips: add initial Global Config Register support
target-mips: add CMGCRBase register
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Bypass View does not cause issuing thread to block and does not affect
any of the cells state bit.
Read from a FIFO cell returns the value of the oldest entry.
Store to a FIFO cell changes the value of the newest entry.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
P/V Synchronized and Try Views can be used to access Semaphore cells.
Load returns current value and post-decrements the value in the cell
(until it reaches zero). Stores increment the value (until it saturates
at 0xFFFF).
P/V Synchronized View causes the issuing thread to block on read if value
is 0. P/V Try View does not block the thread, it returns 0 in this case.
Cell's Empty and Full bits are not modified.
Trap bit (i.e. Gating Storage exceptions) not implemented.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Empty/Full Synchronized and Try views can be used to access FIFO cells.
Store to the FIFO cell pushes the value into the queue, load pops the oldest
element from the queue. Cell's Full and Empty bits are automatically updated
to reflect new state of the cell.
Empty/Full Synchronized View causes the issuing thread to block when FIFO is
empty while thread is performing a read, or FIFO is full while thread is
performing a write.
Empty/Full Try View never blocks the thread. If cell is full then write is
ignored, if cell is empty then load returns 0.
Trap bit (i.e. Gating Storage exceptions) not implemented.
Store Conditional support for E/F Try View (i.e. indicate failure if FIFO
is full) not implemented.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Control view is used to access the ITC Storage Cell Tags. It never causes
the issuing thread to block.
Guest can empty the FIFO cell by setting Empty bit to 1.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Implement ITC as a single object consisting of two memory regions:
1) tag_io: ITC Configuration Tags (i.e. ITCAddressMap{0,1} registers) which
are accessible by the CPU via CACHE instruction. Also adding
MemoryRegion *itc_tag to the CPUMIPSState so that CACHE instruction will
dispatch reads/writes directly.
2) storage_io: memory-mapped ITC Storage whose address space is configurable
(i.e. enabled/remapped/resized) by writing to ITCAddressMap{0,1} registers.
ITC Storage contains FIFO and Semaphore cells. Read-only FIFO bit in the
ITC cell tag indicates the type of the cell. If the ITC Storage contains
both types of cells then FIFOs are located before Semaphores.
Since issuing thread can get blocked on the access to a cell (in E/F
Synchronized and P/V Synchronized Views) each cell has a bitmap to track
which threads are currently blocked.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
If the user specifies smp > 1 and the CPU with CM GCR support, then
create Coherent Processing System (which takes care of instantiating CPUs)
rather than CPUs directly and connect i8259 and cbus to the pins exposed by
CPS. However, there is no GIC yet, thus CPS exposes CPU's IRQ pins so use
the same pin numbers as before.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Global smp_cpus is never zero (even if user provides -smp 0), thus clocks
and irqs are always initialized for each created CPU in the loop at the
beginning of mips_malta_init.
These two lines cause a leak of already allocated timer and irqs for the
first CPU - remove them.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Create Cluster Power Controller and add a link to the CPC MemoryRegion
in GCR. Guest can enable / map CPC to any physical address by writing to
the memory-mapped GCR_CPC_BASE register.
Set vp-start-reset property to 1 to allow only first VP to run from reset.
Others are brought up by the guest via CPC memory-mapped registers.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Cluster Power Controller (CPC) is responsible for power management in
multiprocessing system. It provides registers to control the power and the
clock frequency of the individual elements in the system.
This patch implements only three registers that are used to control the
power state of each VP on a single core:
* VP Run is a write-only register used to set each VP to the run state
* VP Stop is a write-only register used to set each VP to the suspend state
* VP Running is a read-only register indicating the run state of each VP
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add initial GCR support to indicate number of VPs present in the system,
L2 bypass mode and revision number.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
[leon.alrae@imgtec.com:
* removed GIC part,
* changed commit message,
* replaced %lx format spec. with PRIx64,
* renamed mips_gcr.{c,h} to mips_cmgcr.{c,h},
* replaced CONFIG_MIPS_GIC with CONFIG_MIPS_CPS]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Implement generic MIPS Coherent Processing System (CPS) which in this
commit just creates VPs, but it will serve as a container also for
other components like Global Configuration Registers and Cluster Power
Controller.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This reverts commit 9596ef7c7b.
This workaround in order to fix endless interrupts is no
longer needed because it was superseded by the previous patch
(e1000: Fixing interrupt pace).
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This patch introduces an upper bound for number of interrupts
per second. Without this bound an interrupt storm can occur as
it has been observed on Windows 10 when disabling the device.
According to the SPEC - Intel PCI/PCI-X Family of Gigabit
Ethernet Controllers Software Developer's Manual, section
13.4.18 - the Ethernet controller guarantees a maximum
observable interrupt rate of 7813 interrupts/sec. If there is
no upper bound this could lead to an interrupt storm by e1000
(when mit_delay < 500) causing interrupts to fire at a very high
pace.
Thus if mit_delay < 500 then the delay should be set to the
minimum delay possible which is 500. This can be calculated
easily as follows:
Interval = 10^9 / (7813 * 256) = 500.
Signed-off-by: Sameeh Jubran <sameeh@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
- Use 128bit math to avoid asserts with IOMMU regions (Bandan Das)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=DpB8
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/awilliam/tags/vfio-update-20160328.0' into staging
VFIO updates 2016-03-28
- Use 128bit math to avoid asserts with IOMMU regions (Bandan Das)
# gpg: Signature made Mon 28 Mar 2016 23:16:52 BST using RSA key ID 3BB08B22
# gpg: Good signature from "Alex Williamson <alex.williamson@redhat.com>"
# gpg: aka "Alex Williamson <alex@shazbot.org>"
# gpg: aka "Alex Williamson <alwillia@redhat.com>"
# gpg: aka "Alex Williamson <alex.l.williamson@gmail.com>"
* remotes/awilliam/tags/vfio-update-20160328.0:
vfio: convert to 128 bit arithmetic calculations when adding mem regions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
vfio_listener_region_add for a iommu mr results in
an overflow assert since iommu memory region is initialized
with UINT64_MAX. Convert calculations to 128 bit arithmetic
for iommu memory regions and let int128_get64 assert for non iommu
regions if there's an overflow.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
[missed (end - 1) on 2nd trace call, move llsize closer to use]
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJW9ErPAAoJEL/70l94x66DJfEH/A/QkMpAhrgNdyVsahzsGrzE
wx5gHFIc1nBYxyr62w4apUb5jPB7zaXu0LA7EAWDeAe0pyP8hZzLT9kJyOEDsuJu
zwKN2QeLSNMtPbnbKN0I/YQ2za2xX1V5ruhSeOJoVslUI214hgnAURaGshhQNzuZ
2CluDT9KgL5cQifAnKs5kJrwhIYShYNQB+1eDC/7wk28dd/EH+sPALIoF+rqrSmt
Zu4Mdqd+9Ns+oKOjA6br9ULq/Hzg0aDfY82J+XLVVqfF3PXQe8rTDmuMf/7jTn+M
Un7ZOcei9oZF2/9vfAfKQpDCcgD9HvOUSbgqV/ubmkPPmN/LNJzeKj0fBhrRN+Y=
=K12D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Log filtering from Alex and Peter
* Chardev fix from Marc-André
* config.status tweak from David
* Header file tweaks from Markus, myself and Veronia (Outreachy candidate)
* get_ticks_per_sec() removal from Rutuja (Outreachy candidate)
* Coverity fix from myself
* PKE implementation from myself, based on rth's XSAVE support
# gpg: Signature made Thu 24 Mar 2016 20:15:11 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
* remotes/bonzini/tags/for-upstream: (28 commits)
target-i386: implement PKE for TCG
config.status: Pass extra parameters
char: translate from QIOChannel error to errno
exec: fix error handling in file_ram_alloc
cputlb: modernise the debug support
qemu-log: support simple pid substitution for logs
target-arm: dfilter support for in_asm
qemu-log: dfilter-ise exec, out_asm, op and opt_op
qemu-log: new option -dfilter to limit output
qemu-log: Improve the "exec" TB execution logging
qemu-log: Avoid function call for disabled qemu_log_mask logging
qemu-log: correct help text for -d cpu
tcg: pass down TranslationBlock to tcg_code_gen
util: move declarations out of qemu-common.h
Replaced get_tick_per_sec() by NANOSECONDS_PER_SECOND
hw: explicitly include qemu-common.h and cpu.h
include/crypto: Include qapi-types.h or qemu/bswap.h instead of qemu-common.h
isa: Move DMA_transfer_handler from qemu-common.h to hw/isa/isa.h
Move ParallelIOArg from qemu-common.h to sysemu/char.h
Move QEMU_ALIGN_*() from qemu-common.h to qemu/osdep.h
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Conflicts:
scripts/clean-includes
RX buffer pools are now enabled by default for new machine types.
For older machine types, they are still disabled to avoid breaking
migration.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
tl;dr:
This patch introduces an alternate way of handling the receive
buffers of the spapr-vlan device, resulting in much better
receive performance for the guest.
Full story:
One of our testers recently discovered that the performance of the
spapr-vlan device is very poor compared to other NICs, and that
a simple "ping -i 0.2 -s 65507 someip" in the guest can result
in more than 50% lost ping packets (especially with older guest
kernels < 3.17).
After doing some analysis, it was clear that there is a problem
with the way we handle the receive buffers in spapr_llan.c: The
ibmveth driver of the guest Linux kernel tries to add a lot of
buffers into several buffer pools (with 512, 2048 and 65536 byte
sizes by default, but it can be changed via the entries in the
/sys/devices/vio/1000/pool* directories of the guest). However,
the spapr-vlan device of QEMU only tries to squeeze all receive
buffer descriptors into one single page which has been supplied
by the guest during the H_REGISTER_LOGICAL_LAN call, without
taking care of different buffer sizes. This has two bad effects:
First, only a very limited number of buffer descriptors is accepted
at all. Second, we also hand 64k buffers to the guest even if
the 2k buffers would fit better - and this results in dropped packets
in the IP layer of the guest since too much skbuf memory is used.
Though it seems at a first glance like PAPR says that we should store
the receive buffer descriptors in the page that is supplied during
the H_REGISTER_LOGICAL_LAN call, chapter 16.4.1.2 in the LoPAPR spec
declares that "the contents of these descriptors are architecturally
opaque, none of these descriptors are manipulated by code above
the architected interfaces". That means we don't have to store
the RX buffer descriptors in this page, but can also manage the
receive buffers at the hypervisor level only. This is now what we
are doing here: Introducing proper RX buffer pools which are also
sorted by size of the buffers, so we can hand out a buffer with
the best fitting size when a packet has been received.
To avoid problems with migration from/to older version of QEMU,
the old behavior is also retained and enabled by default. The new
buffer management has to be enabled via a new "use-rx-buffer-pools"
property.
Now with the new buffer pool management enabled, the problem with
"ping -s 65507" is fixed for me, and the throughput of a simple
test with wget increases from creeping 3MB/s up to 20MB/s!
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Refactor the code a little bit by extracting the code that reads
and writes the receive buffer list page into separate functions.
There should be no functional change in this patch, this is just
a preparation for the upcoming extensions that introduce receive
buffer pools.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
And move the code adjusting the MSR mask and calling kvmppc_set_papr()
to it. This allows us to add a few more things such as disabling setting
of MSR:HV and appropriate LPCR bits which will be used when fixing
the exception model.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[clg: removed LPCR setting ]
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ePAPR defines "hcall-instructions" device-tree property which contains
code to call hypercalls in ePAPR paravirtualized guests. In general
pseries guests won't use this property, instead using the PAPR defined
hypercall interface.
However, this property has been re-used to implement a hack to allow
PR KVM to run (slightly modified) guests in some situations where it
otherwise wouldn't be able to (because the system's L0 hypervisor
doesn't forward the PAPR hypercalls to the PR KVM kernel).
Hence, this property is always present in the device tree for pseries
guests. All KVM guests use it at least to read features via the
KVM_HC_FEATURES hypercall.
The property is populated by the code returned from the KVM's
KVM_PPC_GET_PVINFO ioctl; if not implemented in the KVM, QEMU supplies
code which will fail all hypercall attempts. If QEMU does not create
the property, and the guest kernel is compiled with
CONFIG_EPAPR_PARAVIRT (which is normally the case), there is exactly
the same stub at @epapr_hypercall_start already.
Rather than maintaining this fairly useless stub implementation, it
makes more sense not to create the property in the device tree in the
first place if the host kernel does not implement it.
This changes kvmppc_get_hypercall() to return 1 if the host kernel
does not implement KVM_CAP_PPC_GET_PVINFO. The caller can use it to decide
on whether to create the property or not.
This changes the pseries machine to not create the property if KVM does
not implement KVM_PPC_GET_PVINFO. In practice this means that from now
on the property will not be created if either HV KVM or TCG is used.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[reworded commit message for clarity --dwg]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEMm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-ivshmem-2016-03-18' into staging
ivshmem: Fixes, cleanups, device model split
# gpg: Signature made Mon 21 Mar 2016 20:33:54 GMT using RSA key ID EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
* remotes/armbru/tags/pull-ivshmem-2016-03-18: (40 commits)
contrib/ivshmem-server: Print "not for production" warning
ivshmem: Require master to have ID zero
ivshmem: Drop ivshmem property x-memdev
ivshmem: Clean up after the previous commit
ivshmem: Split ivshmem-plain, ivshmem-doorbell off ivshmem
ivshmem: Replace int role_val by OnOffAuto master
qdev: New DEFINE_PROP_ON_OFF_AUTO
ivshmem: Inline check_shm_size() into its only caller
ivshmem: Simplify memory regions for BAR 2 (shared memory)
ivshmem: Implement shm=... with a memory backend
ivshmem: Tighten check of property "size"
ivshmem: Simplify how we cope with short reads from server
ivshmem: Drop the hackish test for UNIX domain chardev
ivshmem: Rely on server sending the ID right after the version
ivshmem: Propagate errors through ivshmem_recv_setup()
ivshmem: Receive shared memory synchronously in realize()
ivshmem: Plug leaks on unplug, fix peer disconnect
ivshmem: Disentangle ivshmem_read()
ivshmem: Simplify rejection of invalid peer ID from server
ivshmem: Assert interrupts are set up once
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
DMA_transfer_handler is actually an ISA thing, and as such has no
business in qemu-common.h. Move it to hw/isa/isa.h, and rename it to
IsaDmaTransferHandler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu-common.h should only be included by .c files. Its file comment
explains why: "No header file should depend on qemu-common.h, as this
would easily lead to circular header dependencies."
hw/pci/pci.h includes qemu-common.h, but its users only need pcibus_t
and PCIHostDeviceAddress from it. Move them to hw/pci/pci.h and drop
the ill-advised include. Include hw/pci/pci.h where the moved stuff
is now missing. Except we can't in target-i386/kvm_i386.h, because
that would break the i386-linux-user compile. Add
PCIHostDeviceAddress to qemu/typedefs.h instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu-common.h should only be included by .c files. Its file comment
explains why: "No header file should depend on qemu-common.h, as this
would easily lead to circular header dependencies."
hw/hw.h includes qemu-common.h, but its users generally need only
hw_error() and qemu/module.h from it. Move the former to hw/hw.h,
include the latter there, and drop the ill-advised include.
hw/misc/cbus.c now misses hw_error(), so include hw/hw.h there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Manually drop redundant includes that scripts/clean-includes misses,
e.g. because they're hidden in generator programs, or they use the
wrong kind of delimiter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Re-run scripts/clean-includes to apply the previous commit's
corrections and updates. Besides redundant qemu/typedefs.h, this only
finds a redundant config-host.h include in ui/egl-helpers.c. No idea
how that escaped the previous runs.
Some manual whitespace trimming around dropped includes squashed in.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Migration with ivshmem needs to be carefully orchestrated to work.
Exactly one peer (the "master") migrates to the destination, all other
peers need to unplug (and disconnect), migrate, plug back (and
reconnect). This is sort of documented in qemu-doc.
If peers connect on the destination before migration completes, the
shared memory can get messed up. This isn't documented anywhere. Fix
that in qemu-doc.
To avoid messing up register IVPosition on migration, the server must
assign the same ID on source and destination. ivshmem-spec.txt leaves
ID assignment unspecified, however.
Amend ivshmem-spec.txt to require the first client to receive ID zero.
The example ivshmem-server complies: it always assigns the first
unused ID.
For a bit of additional safety, enforce ID zero for the master. This
does nothing when we're not using a server, because the ID is zero for
all peers then.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-40-git-send-email-armbru@redhat.com>
Move code to more sensible places. Use the opportunity to reorder and
document IVShmemState members.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-38-git-send-email-armbru@redhat.com>
ivshmem can be configured with and without interrupt capability
(a.k.a. "doorbell"). The two configurations have largely disjoint
options, which makes for a confusing (and badly checked) user
interface. Moreover, the device can't tell the guest whether its
doorbell is enabled.
Create two new device models ivshmem-plain and ivshmem-doorbell, and
deprecate the old one.
Changes from ivshmem:
* PCI revision is 1 instead of 0. The new revision is fully backwards
compatible for guests. Guests may elect to require at least
revision 1 to make sure they're not exposed to the funny "no shared
memory, yet" state.
* Property "role" replaced by "master". role=master becomes
master=on, role=peer becomes master=off. Default is off instead of
auto.
* Property "use64" is gone. The new devices always have 64 bit BARs.
Changes from ivshmem to ivshmem-plain:
* The Interrupt Pin register in PCI config space is zero (does not use
an interrupt pin) instead of one (uses INTA).
* Property "x-memdev" is renamed to "memdev".
* Properties "shm" and "size" are gone. Use property "memdev"
instead.
* Property "msi" is gone. The new device can't have MSI-X capability.
It can't interrupt anyway.
* Properties "ioeventfd" and "vectors" are gone. They're meaningless
without interrupts anyway.
Changes from ivshmem to ivshmem-doorbell:
* Property "msi" is gone. The new device always has MSI-X capability.
* Property "ioeventfd" defaults to on instead of off.
* Property "size" is gone. The new device can only map all the shared
memory received from the server.
Guests can easily find out whether the device is configured for
interrupts by checking for MSI-X capability.
Note: some code added in sub-optimal places to make the diff easier to
review. The next commit will move it to more sensible places.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-37-git-send-email-armbru@redhat.com>
In preparation of making it a qdev property.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-36-git-send-email-armbru@redhat.com>
ivshmem_realize() puts the shared memory region in a container region.
Used to be necessary to permit delayed mapping of the shared memory.
However, we recently moved to synchronous mapping, in "ivshmem:
Receive shared memory synchronously in realize()" and the commit
following it. The container is redundant since then. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1458066895-20632-33-git-send-email-armbru@redhat.com>
ivshmem has its very own code to create and map shared memory.
Replace that with an implicitly created memory backend. Reduces the
number of ways we create BAR 2 from three to two.
The memory-backend-file is currently available only with CONFIG_LINUX,
so this adds a second Linuxism to ivshmem (the other one is eventfd).
Should we ever need to make it portable to systems where
memory-backend-file can't be made to serve, we could create a
memory-backend-shmem that allocates memory with shm_open().
Bonus fix: shared memory files are now created with permissions 0655
instead of 0777.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1458066895-20632-32-git-send-email-armbru@redhat.com>
If size_t is narrower than 64 bits, passing uint64_t ivshmem_size to
mmap() truncates. Reject such sizes.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-31-git-send-email-armbru@redhat.com>
Short reads from a UNIX domain sockets are exceedingly unlikely when
the other side always sends eight bytes and we always read eight
bytes. We cope with them anyway. However, the code doing that is
rather convoluted. Dumb it down radically.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-30-git-send-email-armbru@redhat.com>
The chardev must be capable of transmitting SCM_RIGHTS ancillary
messages. We check it by comparing CharDriverState member filename to
"unix:". That's almost as brittle as it is disgusting.
When the actual transmission all happened asynchronously, this check
was all we could do in realize(), and thus better than nothing. But
now we receive at least one SCM_RIGHTS synchronously in realize(),
it's not worth its keep anymore. Drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-29-git-send-email-armbru@redhat.com>
The protocol specification (ivshmem-spec.txt, formerly
ivshmem_device_spec.txt) has always required the ID message to be sent
right at the beginning, and ivshmem-server has always complied. The
device, however, accepts it out of order. If an interrupt setup
arrived before it, though, it would be misinterpreted as connect
notification. Fix the latent bug by relying on the spec and
ivshmem-server's actual behavior.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-28-git-send-email-armbru@redhat.com>
This kills off the funny state described in the previous commit.
Simplify ivshmem_io_read() accordingly, and update documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1458066895-20632-27-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
When configured for interrupts (property "chardev" given), we receive
the shared memory from an ivshmem server. We do so asynchronously
after realize() completes, by setting up callbacks with
qemu_chr_add_handlers().
Keeping server I/O out of realize() that way avoids delays due to a
slow server. This is probably relevant only for hot plug.
However, this funny "no shared memory, yet" state of the device also
causes a raft of issues that are hard or impossible to work around:
* The guest is exposed to this state: when we enter and leave it its
shared memory contents is apruptly replaced, and device register
IVPosition changes.
This is a known issue. We document that guests should not access
the shared memory after device initialization until the IVPosition
register becomes non-negative.
For cold plug, the funny state is unlikely to be visible in
practice, because we normally receive the shared memory long before
the guest gets around to mess with the device.
For hot plug, the timing is tighter, but the relative slowness of
PCI device configuration has a good chance to hide the funny state.
In either case, guests complying with the documented procedure are
safe.
* Migration becomes racy.
If migration completes before the shared memory setup completes on
the source, shared memory contents is silently lost. Fortunately,
migration is rather unlikely to win this race.
If the shared memory's ramblock arrives at the destination before
shared memory setup completes, migration fails.
There is no known way for a management application to wait for
shared memory setup to complete.
All you can do is retry failed migration. You can improve your
chances by leaving more time between running the destination QEMU
and the migrate command.
To mitigate silent memory loss, you need to ensure the server
initializes shared memory exactly the same on source and
destination.
These issues are entirely undocumented so far.
I'd expect the server to be almost always fast enough to hide these
issues. But then rare catastrophic races are in a way the worst kind.
This is way more trouble than I'm willing to take from any device.
Kill the funny state by receiving shared memory synchronously in
realize(). If your hot plug hangs, go kill your ivshmem server.
For easier review, this commit only makes the receive synchronous, it
doesn't add the necessary error propagation. Without that, the funny
state persists. The next commit will do that, and kill it off for
real.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-26-git-send-email-armbru@redhat.com>
close_peer_eventfds() cleans up three things: ioeventfd triggers if
they exist, eventfds, and the array to store them.
Commit 98609cd (v1.2.0) fixed it not to clean up ioeventfd triggers
when they don't exist (property ioeventfd=off, which is the default).
Unfortunately, the fix also made it skip cleanup of the eventfds and
the array then. This is a memory and file descriptor leak on unplug.
Additionally, the reset of nb_eventfds is skipped. Doesn't matter on
unplug. On peer disconnect, however, this permanently wedges the
interrupt vectors used for that peer's ID. The eventfds stay behind,
but aren't connected to a peer anymore. When the ID gets recycled for
a new peer, the new peer's eventfds get assigned to vectors after the
old ones. Commonly, the device's number of vectors matches the
server's, so the new ones get dropped with a "Too many eventfd
received" message. Interrupts either don't work (common case) or go
to the wrong vector.
Fix by narrowing the conditional to just the ioeventfd trigger
cleanup.
While there, move the "invalid" peer check to the only caller where it
can actually happen, and tighten it to reject own ID.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-25-git-send-email-armbru@redhat.com>
ivshmem_read() processes server messages. These are 64 bit signed
integers. -1 is shared memory setup, 16 bit unsigned is a peer ID,
anything else is invalid.
ivshmem_read() rejects invalid negative messages right away, silently.
Invalid positive messages get rejected only in resize_peers(), and
ivshmem_read() then prints the rather cryptic message "failed to
resize peers array".
Extend the first check to cover all invalid messages, make it report
"server sent invalid message", and drop the second check.
Now resize_peers() can't fail anymore; simplify.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-23-git-send-email-armbru@redhat.com>
An interrupt is set up when the interrupt's file descriptor is
received. Each message applies to the next interrupt vector.
Therefore, each vector cannot be set up more than once.
ivshmem_add_kvm_msi_virq() half-heartedly tries not to rely on this by
doing nothing then, but that's not going to recover from this error
should it become possible in the future. watch_vector_notifier()
doesn't even try.
Simply assert what is the case, so we get alerted if we ever screw it
up.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-22-git-send-email-armbru@redhat.com>
The ivshmem device can either use MSI-X or legacy INTx for interrupts.
With MSI-X enabled, peer interrupt events trigger an MSI as they
should. But software can still raise INTx via interrupt status and
mask register in BAR 0. This is explicitly prohibited by PCI Local
Bus Specification Revision 3.0, section 6.8.3.3:
While enabled for MSI or MSI-X operation, a function is prohibited
from using its INTx# pin (if implemented) to request service (MSI,
MSI-X, and INTx# are mutually exclusive).
Fix the device model to leave INTx alone when using MSI-X.
Document that we claim to use INTx in config space even when we don't.
Unlike other devices, ivshmem does *not* use INTx when configured for
MSI-X and MSI-X isn't enabled by software.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1458066895-20632-21-git-send-email-armbru@redhat.com>
There are three predicates related to MSI-X:
* ivshmem_has_feature(s, IVSHMEM_MSI) is true unless the non-MSI-X
variant of the device is selected with msi=off.
* msix_present() is true when the device has the PCI capability MSI-X.
It's initially false, and becomes true during successful realize of
the MSI-X variant of the device. Thus, it's the same as
ivshmem_has_feature(s, IVSHMEM_MSI) for realized devices.
* msix_enabled() is true when msix_present() is true and guest software
has enabled MSI-X.
Code that differs between the non-MSI-X and the MSI-X variant of the
device needs to be guarded by ivshmem_has_feature(s, IVSHMEM_MSI) or
by msix_present(), except the latter works only for realized devices.
Code that depends on whether MSI-X is in use needs to be guarded with
msix_enabled().
Code review led me to two minor messes:
* ivshmem_vector_notify() calls msix_notify() even when
!msix_enabled(), unlike most other MSI-X-capable devices. As far as
I can tell, msix_notify() does nothing when !msix_enabled(). Add
the guard anyway.
* Most callers of ivshmem_use_msix() guard it with
ivshmem_has_feature(s, IVSHMEM_MSI). Not necessary, because
ivshmem_use_msix() does nothing when !msix_present(). That's
ivshmem's only use of msix_present(), though. Guard it
consistently, and drop the now redundant msix_present() check.
While there, rename ivshmem_use_msix() to ivshmem_msix_vector_use().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1458066895-20632-20-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
If pci_ivshmem_realize() fails after it created its migration blocker,
the blocker is left in place. Fix that by creating it last.
Likewise, if it fails after it called fifo8_create(), it leaks fifo
memory. Fix that the same way.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-18-git-send-email-armbru@redhat.com>
We reuse errp after passing it host_memory_backend_get_memory(). If
both host_memory_backend_get_memory() and the reuse set an error, the
reuse will fail the assertion in error_setv(). Fortunately,
host_memory_backend_get_memory() can't fail.
Pass it &error_abort to make our assumption explicit, and to get the
assertion failure in the right place should it become invalid.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-17-git-send-email-armbru@redhat.com>
Yes, the chardev is commonly useless after we read a bad version from
it, but destroying it is inappropriate anyway: the user created it, so
the user should be able to hold on to it as long as he likes. We
don't destroy it on other errors. Screwed up in commit 5105b1d.
Stop reading instead.
Also note QEMU's behavior in ivshmem-spec.txt.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1458066895-20632-16-git-send-email-armbru@redhat.com>
