This patch changes qemu-img to exit if an unknown option is detected,
instead of trying to continue with a set of arguments which may be
incorrect.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This consolidates the printing of block driver options in
print_block_option_help() which is called from both img_create() and
img_convert().
This allows for the "?" detection to be done just after the parsing of
options and the filename, instead of half way down the codepath of
these functions.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This allows for jumping to 'out:' consistently for error exit.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Filenames may start with "<protocol>:" to explicitly use a protocol like
nbd. Filenames with unknown protocols are rejected in most of QEMU
except for bdrv_create_file(). Even if a file with an invalid filename
can be created, QEMU cannot use it since all the other relevant
functions reject such paths. Make bdrv_create_file() consistent.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This commit causes the watchdog timer to be reset when a guest is
hard-rebooted.
The failure case previously was as follows:
(a) guest boots, watchdog is enabled
(b) guest does a reset eg:
echo 'b' > /proc/sysrq-trigger
(note that an ordinary /sbin/reboot wouldn't hit this case
since as the watchdog daemon is shut down, the daemon would
properly disable the watchdog device)
(c) the reboot takes longer than the remaining time on the
watchdog
(d) the watchdog therefore fires during the reboot
(e) probably the VM would just reboot again at this point which
is pretty benign, but it could depend on the action that the
user had selected for the watchdog
Now we use the qdev reset function to register a reset handler
which disables the timer. Note the handler is called _either_
just after init _or_ when the guest reboots.
In the i6300esb case there is a small refactoring of the code so
that the device's internal state is now fully restored to defaults
on a reboot.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Action that depends on fully initialized device model should register
with this notifier chain.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Change fw_cfg_add_file() to get full file path as a parameter instead
of building one internally. Two reasons for that. First caller may need
to know how file is named. Second this moves policy of file naming out
from fw_cfg. Platform may want to use more then two levels of
directories for instance.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
If bootindex is specified on command line a string that describes device
in firmware readable way is added into sorted list. Later this list will
be passed into firmware to control boot order.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Ports on root hub will have NULL here. This is needed to reconstruct
path from device to its root hub to build device path.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Store all io ports used by device in ISADevice structure.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
New get_fw_dev_path callback will be used for build device path usable
by firmware in contrast to qdev qemu internal device path.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Add "fw_name" to DeviceInfo to use in device path building. In
contrast to "name" "fw_name" should refer to functionality device
provides instead of particular device model like "name" does.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
'info mem' didn't show correct information for PAE mode and
x86_64 long mode.
Fix by implementing the output for missing modes.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
'info tlb' didn't show correct information for PAE mode and
x86_64 long mode.
Implement the missing modes. Also print NX bit for PAE and long modes.
Fix off-by-one error in 32 bit mode mask.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The device shall set its default hardware state after each reset.
This includes that the timer is stopped which is especially important
if the guest does a reboot independantly of a watchdog bite. I moved
the initialization of the state variables completely from the init
to the reset function which is called right after init during the
first boot and afterwards during each reboot.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Minor clean-up in isa-bus.c. Using hw_error is more consistent.
There is a difference however: hw_error dumps the cpu state.
Signed-off-by: Tristan Gingold <gingold@adacore.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Because we don't depend on the target endianness anymore, we can also
move the driver over to Makefile.objs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch converts the ISA MMIO bridge code to always use little endian mmio.
All bswap code that existed was only there to convert from native cpu
endianness to little endian ISA devices.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Because we don't depend on the target endianness anymore, we can also
move the driver over to Makefile.objs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The e1000 has compatibility code to handle big endianness which makes it
mandatory to be recompiled on different targets.
With the generic mmio endianness solution, there's no need for that anymore.
We just declare all mmio to be little endian and call it a day.
Because we don't depend on the target endianness anymore, we can also
move the driver over to Makefile.objs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
There's no need to bswap once we correctly set the mmio to be little endian.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The only reason we have bswap versions of the pci host code is that
most pci host devices are little endian. The ppc e500 is the only
odd one here, being big endian.
So let's directly pass the endianness down to the mmio layer and not
worry about it on the pci host layer.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The device is only used on big endian systems, but always byte swaps. That's
a very good indicator that it's actually a little endian device ;-).
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As an alternative to the 3 individual handlers, there is also a simplified
io mem hook function. To be consistent, let's add an endianness parameter
there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The way we're currently modeling mmio is too simplified. We assume that
every device has the same endianness as the target CPU. In reality,
most devices are little endian (all PCI and ISA ones I'm aware of). Some
are big endian (special system devices) and a very little fraction is
target native endian (fw_cfg).
So instead of assuming every device to be native endianness, let's move
to a model where the device tells us which endianness it's in.
That way we can compile the devices only once and get rid of all the ugly
swap will be done by the underlying layer.
For the same of readability, this patch only introduces the helper framework
but doesn't allow the registering code to set its endianness yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
I get a warning on a signed comparison with an unsigned variable, so
let's make the variable signed and be happy.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
Move the last found TB to the head of the list so it will be found more quickly next time it will be looked for.
Signed-off-by: Kirill Batuzov <batuzovk@ispras.ru>
Signed-off-by: Pavel Yushchenko <pau@ispras.ru>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Remove the spin_trylock() function, as it is not used anywhere,
and is not even implemented if CONFIG_USE_NPTL is defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The redundant forward declaration of qerror in machload.c
is removed because it should be taken from qemu.h.
Please note that this patch is untested because
I have no matching environment to compile it.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This change was missing in commit
9a78eead0c.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
