Currently, the spapr-vlan device is trying to flush the RX queue
after each RX buffer that has been added by the guest via the
H_ADD_LOGICAL_LAN_BUFFER hypercall. In case the receive buffer pool
was empty before, we only pass single packets to the guest this
way. This can cause very bad performance if a sender is trying
to stream fragmented UDP packets to the guest. For example when
using the UDP_STREAM test from netperf with UDP packets that are
much bigger than the MTU size, almost all UDP packets are dropped
in the guest since the chances are quite high that at least one of
the fragments got lost on the way.
When flushing the receive queue, it's much better if we'd have
a bunch of receive buffers available already, so that fragmented
packets can be passed to the guest in one go. To do this, the
spapr_vlan_receive() function should return 0 instead of -1 if there
are no more receive buffers available, so that receive_disabled = 1
gets temporarily set for the receive queue, and we have to delay
the queue flushing at the end of h_add_logical_lan_buffer() a little
bit by using a timer, so that the guest gets a chance to add multiple
RX buffers before we flush the queue again.
This improves the UDP_STREAM test with the spapr-vlan device a lot:
Running
netserver -p 44444 -L <guestip> -f -D -4
in the guest, and
netperf -p 44444 -L <hostip> -H <guestip> -t UDP_STREAM -l 60 -- -m 16384
in the host, I get the following values _without_ this patch:
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
229376 16384 60.00 1738970 0 3798.83
229376 60.00 23 0.05
That "0.05" means that almost all UDP packets got lost/discarded
at the receiving side.
With this patch applied, the value look much better:
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
229376 16384 60.00 1789104 0 3908.35
229376 60.00 22818 49.85
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Mirror the cleanups just done to rlwinm, rlwnm and rlwimi.
This adds use of deposit to rldimi.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A 32-bit rotate insn is more common on hosts than a deposit insn,
and if the host has neither the result is truely horrific.
At the same time, tidy up the temporaries within these functions,
drop the over-use of "likely", drop some checks for identity that
will also be checked by tcg-op.c functions, and special case mask
without rotate within rlwinm.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ppc_hash64_set_external_hpt() was added in e5c0d3c "target-ppc: Add helpers
for updating a CPU's SDR1 and external HPT". This helper contains a
cpu_synchronize_state() since it may need to push state back to KVM
afterwards.
This turns out to break things when it is used in the reset path, which is
the only current user. It appears that kvm_vcpu_dirty is not being set
early in the reset path, so the cpu_synchronize_state() is clobbering state
set up by the early part of the cpu reset path with stale state from KVM.
This may require some changes to the generic cpu reset path to fix
properly, but as a short term fix we can just remove the
cpu_synchronize_state() from ppc_hash64_set_external_hpt(), and require any
non-reset path callers to do that manually.
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
At the moment IOMMU MR only translate to the system memory.
However if some new code changes this, we will need clear indication why
it is not working so here is the check.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since a788f227 "memory: Allow replay of IOMMU mapping notifications"
when new VFIO listener is added, all existing IOMMU mappings are
replayed. However there is a problem that the base address of
an IOMMU memory region (IOMMU MR) is ignored which is not a problem
for the existing user (which is pseries) with its default 32bit DMA
window starting at 0 but it is if there is another DMA window.
This stores the IOMMU's offset_within_address_space and adjusts
the IOVA before calling vfio_dma_map/vfio_dma_unmap.
As the IOMMU notifier expects IOVA offset rather than the absolute
address, this also adjusts IOVA in sPAPR H_PUT_TCE handler before
calling notifier(s).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
7532d3cbf "vfio: Fix 128 bit handling" added support for 64bit IOMMU
memory regions when those are added to VFIO address space; however
removing code cannot cope with these as int128_get64() will fail on
1<<64.
This copies 128bit handling from region_add() to region_del().
Since the only machine type which is actually going to use 64bit IOMMU
is pseries and it never really removes them (instead it will dynamically
add/remove subregions), this should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Document the usage modes, host primary graphics considerations, usage,
and fw_cfg ABI required for IGD assignment with vfio.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
The IGD OpRegion is enabled automatically when running in legacy mode,
but it can sometimes be useful in universal passthrough mode as well.
Without an OpRegion, output spigots don't work, and even though Intel
doesn't officially support physical outputs in UPT mode, it's a
useful feature. Note that if an OpRegion is enabled but a monitor is
not connected, some graphics features will be disabled in the guest
versus a headless system without an OpRegion, where they would work.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Enable quirks to support SandyBridge and newer IGD devices as primary
VM graphics. This requires new vfio-pci device specific regions added
in kernel v4.6 to expose the IGD OpRegion, the shadow ROM, and config
space access to the PCI host bridge and LPC/ISA bridge. VM firmware
support, SeaBIOS only so far, is also required for reserving memory
regions for IGD specific use. In order to enable this mode, IGD must
be assigned to the VM at PCI bus address 00:02.0, it must have a ROM,
it must be able to enable VGA, it must have or be able to create on
its own an LPC/ISA bridge of the proper type at PCI bus address
00:1f.0 (sorry, not compatible with Q35 yet), and it must have the
above noted vfio-pci kernel features and BIOS. The intention is that
to enable this mode, a user simply needs to assign 00:02.0 from the
host to 00:02.0 in the VM:
-device vfio-pci,host=0000:00:02.0,bus=pci.0,addr=02.0
and everything either happens automatically or it doesn't. In the
case that it doesn't, we leave error reports, but assume the device
will operate in universal passthrough mode (UPT), which doesn't
require any of this, but has a much more narrow window of supported
devices, supported use cases, and supported guest drivers.
When using IGD in this mode, the VM firmware is required to reserve
some VM RAM for the OpRegion (on the order or several 4k pages) and
stolen memory for the GTT (up to 8MB for the latest GPUs). An
additional option, x-igd-gms allows the user to specify some amount
of additional memory (value is number of 32MB chunks up to 512MB) that
is pre-allocated for graphics use. TBH, I don't know of anything that
requires this or makes use of this memory, which is why we don't
allocate any by default, but the specification suggests this is not
actually a valid combination, so the option exists as a workaround.
Please report if it's actually necessary in some environment.
See code comments for further discussion about the actual operation
of the quirks necessary to assign these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Capability probing modifies wmask, which quirks may be interested in
changing themselves. Apply our BAR quirks after the capability scan
to make this possible.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Combine VGA discovery and registration. Quirks can have dependencies
on BARs, so the quirks push out until after we've scanned the BARs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
This function returns success if either we setup the VGA region or
the host vfio doesn't return enough regions to support the VGA index.
This latter case doesn't make any sense. If we're asked to populate
VGA, fail if it doesn't exist and let the caller decide if that's
important.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Given a device specific region type and sub-type, find it. Also
cleanup return point on error in vfio_get_region_info() so that we
always return 0 with a valid pointer or -errno and NULL.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
The sparse mmap capability in a vfio region info allows vfio to tell
us which sub-areas of a region may be mmap'd. Thus rather than
assuming a single mmap covers the entire region and later frobbing it
ourselves for things like the PCI MSI-X vector table, we can read that
directly from vfio.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
This is a big refactoring of the migration backend code - moving away from
QEMUFile to the new QIOChannel framework introduced here. This brings a
good level of abstraction and reduction of many lines of code.
This series also adds the ability for many backends (all except RDMA) to
use TLS for encrypting the migration data between the endpoints.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXRpKMAAoJEOsLTfxlfvZw2FMQAJmrp8ijvJNtdBa51bNY+xVx
zvrHDpWco/HxxqyBIGxG7g8Iq+wpNsdgoRxoQkfgIz9RkZiNrzb1kGRiqNFFBKFX
ziK1QQQ12ETUXwQ6VguBuwLDvCCenyUti0HfKkceG+Zu5263fyp+VzL+PuEtteT3
M0pZRrifj/TQqCBXR8yhBAo2dCiFETLVoruE+iNg2ipI3JDizxy8bdOU2gfnTayf
na7lE53pI+Wy8KE+qrhtsEgjHFp48uJ0HwQIIumvVndXFpIhRzCcN/aeVCjNYRjo
GeI18OJxcimRDwsnfuOwuZKhRcjWfa8WEIKsi8LdRTZFpFL6y9R57XNTBIFfbjOF
0lkmFTqJTBi3OTPjj0hMjpjOfXhyKUnwdqCAYlAxeuWHhqPDDhtEcnNtGdmQzx4Z
KvYzc3t31o1gPin024UUfA528PNREszaXhTM90/Dj0dhVSMoG1VQsQjxzkPXxdM1
wemfic+77Bk4oUrSplhdvvk4nySDWeseEjfdyVU2ixqldy8Ib1+6H+PCjWNotpQ0
YiDOHBy3rrUh6NhIqb0C2PWvd/9Aqs0nHQHJ8QKYK574MDbVo8mKTACFdoSYoZ1u
wuif7NL6qkyS55szf0dm8zPBCJ5nIR5SQE98E7+ptXNa8AipfFsTkZrr3aOjcdey
98AWF9KaZOWRfwgIm3Ft
=AYEK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/amit-migration/tags/migration-2.7-2' into staging
migration: add TLS support to the migration data channel
This is a big refactoring of the migration backend code - moving away from
QEMUFile to the new QIOChannel framework introduced here. This brings a
good level of abstraction and reduction of many lines of code.
This series also adds the ability for many backends (all except RDMA) to
use TLS for encrypting the migration data between the endpoints.
# gpg: Signature made Thu 26 May 2016 07:07:08 BST using RSA key ID 657EF670
# gpg: Good signature from "Amit Shah <amit@amitshah.net>"
# gpg: aka "Amit Shah <amit@kernel.org>"
# gpg: aka "Amit Shah <amitshah@gmx.net>"
* remotes/amit-migration/tags/migration-2.7-2: (28 commits)
migration: remove qemu_get_fd method from QEMUFile
migration: remove support for non-iovec based write handlers
migration: add support for encrypting data with TLS
migration: define 'tls-creds' and 'tls-hostname' migration parameters
migration: don't use an array for storing migrate parameters
migration: move definition of struct QEMUFile back into qemu-file.c
migration: delete QEMUFile stdio implementation
migration: delete QEMUFile sockets implementation
migration: delete QEMUSizedBuffer struct
migration: delete QEMUFile buffer implementation
migration: convert savevm to use QIOChannel for writing to files
migration: convert RDMA to use QIOChannel interface
migration: convert exec socket protocol to use QIOChannel
migration: convert fd socket protocol to use QIOChannel
migration: convert tcp socket protocol to use QIOChannel
migration: rename unix.c to socket.c
migration: convert unix socket protocol to use QIOChannel
migration: convert post-copy to use QIOChannelBuffer
migration: add reporting of errors for outgoing migration
migration: add helpers for creating QEMUFile from a QIOChannel
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=g40O
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches
# gpg: Signature made Wed 25 May 2016 18:32:40 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream: (31 commits)
blockjob: Remove BlockJob.bs
commit: Use BlockBackend for I/O
backup: Use BlockBackend for I/O
backup: Remove bs parameter from backup_do_cow()
backup: Pack Notifier within BackupBlockJob
backup: Don't leak BackupBlockJob in error path
mirror: Use BlockBackend for I/O
mirror: Allow target that already has a BlockBackend
stream: Use BlockBackend for I/O
block: Make blk_co_preadv/pwritev() public
block: Convert block job core to BlockBackend
block: Default to enabled write cache in blk_new()
block: Cancel jobs first in bdrv_close_all()
block: keep a list of block jobs
block: Rename blk_write_zeroes()
dma-helpers: change BlockBackend to opaque value in DMAIOFunc
dma-helpers: change interface to byte-based
block: Propagate .drained_begin/end callbacks
block: Fix reconfiguring graph with drained nodes
block: Make bdrv_drain() use bdrv_drained_begin/end()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move bus type and related APIs to a separate file bus.c.
This is a first step in breaking up qdev.c into more manageable chunks.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[AF: Rebased onto osdep.h]
Signed-off-by: Andreas Färber <afaerber@suse.de>
[PMM: added bus.o to link line for test-qdev-global-props]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is not safe to make a direct jump to a TB spanning two pages in
system emulation because the mapping for the second page can get changed
but we don't take care of direct jumps in this case.
However in user mode emulation, this is not the case because there's
only static address translation and TBs are always invalidated properly.
Fixes: 5b053a4a28 ("tcg: Clean up direct block chaining safety checks")
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Message-id: 1463404380-29302-1-git-send-email-sergey.fedorov@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=AMGu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/afaerber/tags/maintainers-for-peter' into staging
Andreas stepping down from most maintainer positions
# gpg: Signature made Wed 25 May 2016 16:53:45 BST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/maintainers-for-peter:
MAINTAINERS: Drop Andreas as CPU maintainer
MAINTAINERS: Drop Andreas as 0.15 maintainer
MAINTAINERS: Drop Andreas as PReP maintainer
MAINTAINERS: Drop Andreas as Cocoa maintainer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that there is a set_blocking callback in QEMUFileOps,
and all users needing non-blocking support have been
converted to QIOChannel, there is no longer any codepath
requiring the qemu_get_fd() method for QEMUFile. Remove it
to avoid further code being introduced with an expectation
of direct file handle access.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-29-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
All the remaining QEMUFile implementations provide an iovec
based write handler, so the put_buffer callback can be removed
to simplify the code.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-28-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
This extends the migration_set_incoming_channel and
migration_set_outgoing_channel methods so that they
will automatically wrap the QIOChannel in a
QIOChannelTLS instance if TLS credentials are configured
in the migration parameters.
This allows TLS to work for tcp, unix, fd and exec
migration protocols. It does not (currently) work for
RDMA since it does not use these APIs, but it is
unlikely that TLS would be desired with RDMA anyway
since it would degrade the performance to that seen
with TCP defeating the purpose of using RDMA.
On the target host, QEMU would be launched with a set
of TLS credentials for a server endpoint
$ qemu-system-x86_64 -monitor stdio -incoming defer \
-object tls-creds-x509,dir=/home/berrange/security/qemutls,endpoint=server,id=tls0 \
...other args...
To enable incoming TLS migration 2 monitor commands are
then used
(qemu) migrate_set_str_parameter tls-creds tls0
(qemu) migrate_incoming tcp:myhostname:9000
On the source host, QEMU is launched in a similar
manner but using client endpoint credentials
$ qemu-system-x86_64 -monitor stdio \
-object tls-creds-x509,dir=/home/berrange/security/qemutls,endpoint=client,id=tls0 \
...other args...
To enable outgoing TLS migration 2 monitor commands are
then used
(qemu) migrate_set_str_parameter tls-creds tls0
(qemu) migrate tcp:otherhostname:9000
Thanks to earlier improvements to error reporting,
TLS errors can be seen 'info migrate' when doing a
detached migration. For example:
(qemu) info migrate
capabilities: xbzrle: off rdma-pin-all: off auto-converge: off zero-blocks: off compress: off events: off x-postcopy-ram: off
Migration status: failed
total time: 0 milliseconds
error description: TLS handshake failed: The TLS connection was non-properly terminated.
Or
(qemu) info migrate
capabilities: xbzrle: off rdma-pin-all: off auto-converge: off zero-blocks: off compress: off events: off x-postcopy-ram: off
Migration status: failed
total time: 0 milliseconds
error description: Certificate does not match the hostname localhost
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-27-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Define two new migration parameters to be used with TLS encryption.
The 'tls-creds' parameter provides the ID of an instance of the
'tls-creds' object type, or rather a subclass such as 'tls-creds-x509'.
Providing these credentials will enable use of TLS on the migration
data stream.
If using x509 certificates, together with a migration URI that does
not include a hostname, the 'tls-hostname' parameter provides the
hostname to use when verifying the server's x509 certificate. This
allows TLS to be used in combination with fd: and exec: protocols
where a TCP connection is established by a 3rd party outside of
QEMU.
NB, this requires changing the migrate_set_parameter method in the
HMP to accept a 's' (string) value instead of 'i' (integer). This
is backwards compatible, because the parsing of strings allows the
quotes to be optional, thus any integer is also a valid string.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-26-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The MigrateState struct uses an array for storing migration
parameters. This presumes that all future parameters will
be integers too, which is not going to be the case. There
is no functional reason why an array is used, if anything
it makes the code less clear. The QAPI schema already
defines a struct - MigrationParameters - capable of storing
all the individual parameters, so just use that instead of
an array.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-25-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Now that the memory buffer based QEMUFile impl is gone, there
is no need for any backend to be accessing internals of the
QEMUFile struct, so it can be moved back into qemu-file.c
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-24-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Now that the exec migration backend and savevm have converted
to use the QIOChannel based QEMUFile, there is no user remaining
for the stdio based QEMUFile impl and it can be deleted.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-23-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Now that the tcp, unix and fd migration backends have converted
to use the QIOChannel based QEMUFile, there is no user remaining
for the sockets based QEMUFile impl and it can be deleted.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-22-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Now that we don't have have a buffer based QemuFile
implementation, the QEMUSizedBuffer code is also
unused and can be deleted. A simpler buffer class
also exists in util/buffer.c which other code can
used as needed.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-21-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The qemu_bufopen() method is no longer used, so the memory
buffer based QEMUFile backend can be deleted entirely.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-20-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Convert the exec savevm code to use QIOChannel and QEMUFileChannel,
instead of the stdio APIs.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-19-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
This converts the RDMA code to provide a subclass of QIOChannel
that uses RDMA for the data transport.
This implementation of RDMA does not correctly handle non-blocking
mode. Reads might block if there was not already some pending data
and writes will block until all data is sent. This flawed behaviour
was already present in the existing impl, so appears to not be a
critical problem at this time. It should be on the list of things
to fix in the future though.
The RDMA code would be much better off it it could be split up in
a generic RDMA layer, a QIOChannel impl based on RMDA, and then
the RMDA migration glue. This is left as a future exercise for
the brave.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-18-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Convert the exec socket migration protocol driver to use
QIOChannel and QEMUFileChannel, instead of the stdio
popen APIs. It can be unconditionally built because the
QIOChannelCommand class can report suitable error messages
on platforms which can't fork processes.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-17-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Convert the fd socket migration protocol driver to use
QIOChannel and QEMUFileChannel, instead of plain sockets
APIs. It can be unconditionally built because the
QIOChannel APIs it uses will take care to report suitable
error messages if needed.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-16-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Drop the current TCP socket migration driver and extend
the new generic socket driver to cope with the TCP address
format
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-15-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The unix.c file will be nearly the same as the tcp.c file,
only differing in the initial SocketAddress creation code.
Rename unix.c to socket.c and refactor it a little to
prepare for merging the TCP code.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-14-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Convert the unix socket migration protocol driver to use
QIOChannel and QEMUFileChannel, instead of plain sockets
APIs. It can be unconditionally built, since the socket
impl of QIOChannel will report a suitable error on platforms
where UNIX sockets are unavailable.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-13-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The post-copy code does some I/O to/from an intermediate
in-memory buffer rather than direct to the underlying
I/O channel. Switch this code to use QIOChannelBuffer
instead of QEMUSizedBuffer.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-12-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Currently if an application initiates an outgoing migration,
it may or may not, get an error reported back on failure. If
the error occurs synchronously to the 'migrate' command
execution, the client app will see the error message. This
is the case for DNS lookup failures. If the error occurs
asynchronously to the monitor command though, the error
will be thrown away and the client left guessing about
what went wrong. This is the case for failure to connect
to the TCP server (eg due to wrong port, or firewall
rules, or other similar errors).
In the future we'll be adding more scope for errors to
happen asynchronously with the TLS protocol handshake.
TLS errors are hard to diagnose even when they are well
reported, so discarding errors entirely will make it
impossible to debug TLS connection problems.
Management apps which do migration are already using
'query-migrate' / 'info migrate' to check up on progress
of background migration operations and to see their end
status. This is a fine place to also include the error
message when things go wrong.
This patch thus adds an 'error-desc' field to the
MigrationInfo struct, which will be populated when
the 'status' is set to 'failed':
(qemu) migrate -d tcp:localhost:9001
(qemu) info migrate
capabilities: xbzrle: off rdma-pin-all: off auto-converge: off zero-blocks: off compress: off events: off x-postcopy-ram: off
Migration status: failed (Error connecting to socket: Connection refused)
total time: 0 milliseconds
In the HMP, when doing non-detached migration, it is
also possible to display this error message directly
to the app.
(qemu) migrate tcp:localhost:9001
Error connecting to socket: Connection refused
Or with QMP
{
"execute": "query-migrate",
"arguments": {}
}
{
"return": {
"status": "failed",
"error-desc": "address resolution failed for myhost:9000: No address associated with hostname"
}
}
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-11-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Currently creating a QEMUFile instance from a QIOChannel is
quite simple only requiring a single call to
qemu_fopen_channel_input or qemu_fopen_channel_output
depending on the end of migration connection.
When QEMU gains TLS support, however, there will need to be
a TLS negotiation done inbetween creation of the QIOChannel
and creation of the final QEMUFile. Introduce some helper
methods that will encapsulate this logic, isolating the
migration protocol drivers from knowledge about TLS.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-10-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Introduce a new QEMUFile implementation that is based on
the QIOChannel objects. This impl is different from existing
impls in that there is no file descriptor that can be made
available, as some channels may be based on higher level
protocols such as TLS.
Although the QIOChannel based implementation can trivially
provide a bi-directional stream, initially we have separate
functions for opening input & output directions to fit with
the expectation of the current QEMUFile interface.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-9-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Instead of relying on the default QEMUFile I/O blocking flag
state, explicitly turn on blocking I/O for outgoing migration
since it takes place in a background thread.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-8-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Remove the assumption that every QEMUFile implementation has
a file descriptor available by introducing a new function
in QEMUFileOps to change the blocking state of a QEMUFile.
If not set, it will fallback to the original code using
the get_fd method.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-7-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The QEMUFileOps struct contains the I/O subsystem callbacks
and the migration stage hooks. Split the hooks out into a
separate QEMUFileHooks struct to make it easier to refactor
the I/O side of QEMUFile without affecting the hooks.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-6-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The QEMUFile writev_buffer / put_buffer functions are expected
to write out the full set of requested data, blocking until
complete. The qemu_fflush() caller does not expect to deal with
partial writes. Clarify the function comments and add a sanity
check to the code to catch mistaken implementations.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-5-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Some of the test-vmstate.c test cases use a temporary file
while others use a memory buffer. To facilitate the future
removal of the qemu_bufopen() function, convert all the tests
to use a temporary file.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-4-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The QIOChannelBuffer's close implementation will free
the internal data buffer. It failed to reset the pointer
to NULL though, so when the object is later finalized
it will free it a second time with predictable crash.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-3-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
The s390 skeys monitor command needs to write out a plain text
file. Currently it is using the QEMUFile class for this, but
work is ongoing to refactor QEMUFile and eliminate much code
related to it. The only feature qemu_fopen() gives over fopen()
is support for QEMU FD passing, but this can be achieved with
qemu_open() + fdopen() too. Switching to regular stdio FILE
APIs avoids the need to sprintf via an intermedia buffer which
slightly simplifies the code.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <1461751518-12128-2-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
