Implement a model of the Message Handling Unit (MHU) found in
the Arm SSE-200. This is a simple device which just contains
some registers which allow the two cores of the SSE-200
to raise interrupts on each other.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-2-peter.maydell@linaro.org
The SSE-200 has a CPU_IDENTITY register block, which is a set of
read-only registers. As well as the usual PID/CID registers, there
is a single CPUID register which indicates whether the CPU is CPU 0
or CPU 1. Implement a model of this register block.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-20-peter.maydell@linaro.org
Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Arm IoTKit includes a system control element which
provides a block of read-only ID registers and a block
of read-write control registers. Implement a minimal
version of this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-9-peter.maydell@linaro.org
The final part of the Memory Protection Controller we need to
implement is actually using the BLK_LUT data programmed by the
guest to determine whether to block the transaction or not.
Since this means we now change transaction mappings when
the guest writes to BLK_LUT, we must also call the IOMMU
notifiers at that point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-5-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
The trace events all use a uint64_t data type, so should be using the
corresponding PRIx64 format, not HWADDR_PRIx which is intended for use
with the 'hwaddr' type.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use types that are defined by QEMU in trace events caused build failures
for the UST trace backend:
In file included from trace-ust-all.c:13:0:
trace-ust-all.h:11844:206: error: unknown type name ‘hwaddr’
It only knows about C built-in types, and any types that are pulled in
from includs of qemu-common.h and lttng/tracepoint.h. This does not
include the 'hwaddr' type, so replace it with a uint64_t which is what
exec/hwaddr.h defines 'hwaddr' as. This fixes the build failure
introduced by
commit 9eb8040c2d
Author: Peter Maydell <peter.maydell@linaro.org>
Date: Fri Mar 2 10:45:39 2018 +0000
hw/misc/tz-ppc: Model TrustZone peripheral protection controller
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180306134317.836-1-berrange@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Arm IoT Kit includes a "security controller" which is largely a
collection of registers for controlling the PPCs and other bits of
glue in the system. This commit provides the initial skeleton of the
device, implementing just the ID registers, and a couple of read-only
read-as-zero registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-16-peter.maydell@linaro.org
Add a model of the TrustZone peripheral protection controller (PPC),
which is used to gate transactions to non-TZ-aware peripherals so
that secure software can configure them to not be accessible to
non-secure software.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-15-peter.maydell@linaro.org
The MPS2 AN505 FPGA image includes a "FPGA control block"
which is a small set of registers handling LEDs, buttons
and some counters.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-14-peter.maydell@linaro.org
The MOS6522 VIA forms the bridge part of several Mac devices, including the
Mac via-cuda and via-pmu devices. Introduce a standard mos6522 device that
can be shared amongst multiple implementations.
This is effectively taking the 6522 parts out of cuda.c and turning them
into a separate device whilst also applying some style tidy-ups and including
a conversion to trace-events.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added Sytem register block of Smartfusion2.
This block has PLL registers which are accessed by guest.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only exception are groups of numers separated by symbols
'.', ' ', ':', '/', like 'ab.09.7d'.
This patch is made by the following:
> find . -name trace-events | xargs python script.py
where script.py is the following python script:
=========================
#!/usr/bin/env python
import sys
import re
import fileinput
rhex = '%[-+ *.0-9]*(?:[hljztL]|ll|hh)?(?:x|X|"\s*PRI[xX][^"]*"?)'
rgroup = re.compile('((?:' + rhex + '[.:/ ])+' + rhex + ')')
rbad = re.compile('(?<!0x)' + rhex)
files = sys.argv[1:]
for fname in files:
for line in fileinput.input(fname, inplace=True):
arr = re.split(rgroup, line)
for i in range(0, len(arr), 2):
arr[i] = re.sub(rbad, '0x\g<0>', arr[i])
sys.stdout.write(''.join(arr))
=========================
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-id: 20170731160135.12101-5-vsementsov@virtuozzo.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
With the move of some docs/ to docs/devel/ on ac06724a71,
no references were updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implement a model of the Serial Communication Controller (SCC) found
in MPS2 FPGA images.
The primary purpose of this device is to communicate with the
Motherboard Configuration Controller (MCC) which is located on
the MPS board itself, outside the FPGA image. This is used
for programming the MPS clock generators. The SCC also has
some basic ID registers and an output for the board LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-7-git-send-email-peter.maydell@linaro.org
The SCU is a collection of chip-level control registers that manage the
various functions supported by ASPEED SoCs. Typically the bits control
interactions with clocks, external hardware or reset behaviour, and we
can largly take a hands-off approach to reads and writes.
Firmware makes heavy use of the state to determine how to boot, but the
reset values vary from SoC to SoC (eg AST2400 vs AST2500). A qdev
property is exposed so that the integrating SoC model can configure the
silicon revision, which in-turn selects the appropriate reset values.
Further qdev properties are exposed so the board model can configure the
board-dependent hardware strapping.
Almost all provided AST2400 reset values are specified by the datasheet.
The notable exception is SOC_SCRATCH1, where we mark the DRAM as
successfully initialised to avoid unnecessary dark corners in the SoC's
u-boot support.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1466744305-23163-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop unnecessary inttypes.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/misc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-14-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>