Support for buffer that are pointed by a pointer (i.e. not embedded)
where the size that we want to use is a field in the state.
We also need a new place to store where to start in the middle of the
buffer, as now it is a pointer, not the offset of the 1st field.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Seeking on vmstate save/load does not work if the underlying file is a
stream. We could try to make all QEMUFile* forward-seek-aware, but first
attempts in this direction indicated that it's saner to convert the few
qemu_fseek-on-vmstates users to plain reads/writes.
This fixes various subtle vmstate corruptions where unused fields were
involved.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The critical part of this change is how to deal with simultaneaous
generation of interrupts. The only (normal) case when this happens in
the emulation is near simultaneous reselection + selection. If selection
comes first, there is no problem, since the target attempting
reselection loses the arbitration (in the emulation it only means that
the reselect function will not be started). In the worst case the host
adapter is reselected, but the device driver already started a
selection, so we jump to the alternative address to handle the
situation.
The SCRIPTS code can trigger another interrupt to notify the driver that
the new task has to be postponed. I suppose that on real hardware there
is enough time after the reselection interrupt to set the SIP bit before
the next interrupt comes, so it would result in 2 stacked interrupts (a
SCSI and a DMA one). However, in the emulation there is no interrupt
stacking, so there is a good chance that the 2 interrupts will get to
the interrupt handler at the same time.
Nevertheless, it should not make a big difference in interrupt handling,
since in both cases both interrupts have to be fetched first, and after
that the new task (that failed during the selection phase) has to be
prepared/reset for a later restart, and the reconnected device has to be
serviced.
The changes do not modify the host adapter's behavior if this interrupt
is not enabled.
See also LSI53C895A technical manual, SCID and SIEN0.
Signed-off-by: Laszlo Ast <laszlo.ast@siemens-enterprise.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
See SCSI-2, 6.5 Message system description/message codes.
Signed-off-by: Laszlo Ast <laszlo.ast@siemens-enterprise.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add READ_16 + friends to scsi-defs.h, scsi_command_name() and the
request parsing helper functions.
Use them in scsi-disk.c too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move VERIFY emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move REPORT_LUNS emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add REPORT_LUNS to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move SERVICE_ACTION_IN emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add SERVICE_ACTION_IN to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move GET_CONFIGURATION emulation from scsi_send_command() to
scsi_disk_emulate_command().
Also add GET_CONFIGURATION to scsi-defs.h and scsi_command_name().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move READ_TOC emulation from scsi_send_command() to
scsi_disk_emulate_command(). Add scsi_disk_emulate_read_toc() function
which holds the longisch READ_TOC emulation code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move SYNCHRONIZE_CACHE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move READ_CAPACITY emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move ALLOW_MEDIUM_REMOVAL emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move START_STOP emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move MODE_SENSE emulation from scsi_send_command() to
scsi_disk_emulate_command(). Create two helper functions:
mode_sense_page() which writes the actual mode pages and
scsi_disk_emulate_mode_sense() which holds the longish MODE_SENSE
emulation code, calling into mode_sense_page() as needed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move RESERVE+RELEASE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move INQUIRY emulation from scsi_send_command() to
scsi_disk_emulate_command(). Also split the longish INQUITY emulation
code into the new scsi_disk_emulate_inquiry() function. Serial number
handling is slightly changed, we don't copy it any more but look it up
directly in DriveInfo which we have at hand anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Move REQUEST_SENSE emulation from scsi_send_command() to
scsi_disk_emulate_command().
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add new scsi_disk_emulate_command() function, which will -- when
finished -- handle all scsi disk command emulation except actual I/O
(READ+WRITE commands) which goes to the block layer. The function
builds on top of the new SCSIRequest struct.
SCSI command emulation code is moved over from scsi_send_command() in
steps to ease review and make it easier to pin down regressions (if any)
using bisect. This patch moves over TEST_UNIT_READY only.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also add and use the scsi_req_complete() helper function for calling the
completion callback.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add helper functions for scsi request parsing to common code. Getting
command length, transfer size, and linear block address is handled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Largely based on <scsi/scsi.h> from linux. Added into the tree so we
can use the defines everywhere, not just in scsi-generic.c (which is
linux-specific).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Create generic functions to allocate, find and release SCSIRequest
structs. Make scsi-disk and scsi-generic use them.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Changes:
* Move from open-coded lists to QTAILQ macros.
* Move the struct elements to the common data structures
(SCSIDevice + SCSIRequest).
* Drop free request pools.
* Fix request cleanup in the destroy callback.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Rename the SCSIRequest structs in scsi-disk.c and scsi-generic.c to
SCSIDiskReq and SCSIGenericReq. Create a SCSIRequest struct and move
the common elements over.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Also delete the leftover and unused scsi-disk.h file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Print an error if the user specifies vnet_hdr=1 on the cmdline.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
net_tap_init() always sets vnet_hdr using qemu_opt_get_bool(), but
initialize it in net_init_tap() just to reduce confusion.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This avoids the "TUNSETOFFLOAD ioctl() failed: Invalid argument" message
on kernels without TUNSETOFFLOAD support.
Signed-off-by: Pierre Riteau <Pierre.Riteau@irisa.fr>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
vnet_hdr is initialized at 1 by default. We need to reset it to 0 if
the kernel doesn't support IFF_VNET_HDR.
Signed-off-by: Pierre Riteau <Pierre.Riteau@irisa.fr>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add a NetClientInfo pointer to VLANClientState and use that
for the typecode and function pointers.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
... and VLANClientState::opaque and qemu_find_vlan_client().
All of these are now unused
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
