Implement the register interface for the SAU: SAU_CTRL,
SAU_TYPE, SAU_RNR, SAU_RBAR and SAU_RLAR. None of the
actual behaviour is implemented here; registers just
read back as written.
When the CPU definition for Cortex-M33 is eventually
added, its initfn will set cpu->sau_sregion, in the same
way that we currently set cpu->pmsav7_dregion for the
M3 and M4.
Number of SAU regions is typically a configurable
CPU parameter, but this patch doesn't provide a
QEMU CPU property for it. We can easily add one when
we have a board that requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-14-git-send-email-peter.maydell@linaro.org
Add the new M profile Secure Fault Status Register
and Secure Fault Address Register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-10-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Update armv7m_nvic_acknowledge_irq() and armv7m_nvic_complete_irq()
to handle banked exceptions:
* acknowledge needs to use the correct vector, which may be
in sec_vectors[]
* acknowledge needs to return to its caller whether the
exception should be taken to secure or non-secure state
* complete needs its caller to tell it whether the exception
being completed is a secure one or not
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-20-git-send-email-peter.maydell@linaro.org
Now that we have a banked FAULTMASK register and banked exceptions,
we can implement the correct check in cpu_mmu_index() for whether
the MPU_CTRL.HFNMIENA bit's effect should apply. This bit causes
handlers which have requested a negative execution priority to run
with the MPU disabled. In v8M the test has to check this for the
current security state and so takes account of banking.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-17-git-send-email-peter.maydell@linaro.org
Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending()
functions take a bool indicating whether to pend the secure
or non-secure version of a banked interrupt, and update the
callsites accordingly.
In most callsites we can simply pass the correct security
state in; in a couple of cases we use TODO comments to indicate
that we will return the code in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org
The Application Interrupt and Reset Control Register has some changes
for v8M:
* new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have
real state if the security extension is implemented and otherwise
are constant
* the PRIGROUP field is banked between security states
* non-secure code can be blocked from using the SYSRESET bit
to reset the system if SYSRESETREQS is set
Implement the new state and the changes to register read and write.
For the moment we ignore the effects of the secure PRIGROUP.
We will implement the effects of PRIS and BFHFNMIS later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org
there are 2 use cases to deal with:
1: fixed CPU models per board/soc
2: boards with user configurable cpu_model and fallback to
default cpu_model if user hasn't specified one explicitly
For the 1st
drop intermediate cpu_model parsing and use const cpu type
directly, which replaces:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
object_new(typename)
with
object_new(FOO_CPU_TYPE_NAME)
or
cpu_generic_init(BASE_CPU_TYPE, "my cpu model")
with
cpu_create(FOO_CPU_TYPE_NAME)
as result 1st use case doesn't have to invoke not necessary
translation and not needed code is removed.
For the 2nd
1: set default cpu type with MachineClass::default_cpu_type and
2: use generic cpu_model parsing that done before machine_init()
is run and:
2.1: drop custom cpu_model parsing where pattern is:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
[parse_features(typename, cpu_model, &err) ]
2.2: or replace cpu_generic_init() which does what
2.1 does + create_cpu(typename) with just
create_cpu(machine->cpu_type)
as result cpu_name -> cpu_type translation is done using
generic machine code one including parsing optional features
if supported/present (removes a bunch of duplicated cpu_model
parsing code) and default cpu type is defined in an uniform way
within machine_class_init callbacks instead of adhoc places
in boadr's machine_init code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1505318697-77161-6-git-send-email-imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Use a symbolic constant M_REG_NUM_BANKS for the array size for
registers which are banked by M profile security state, rather
than hardcoding lots of 2s.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1505137930-13255-2-git-send-email-peter.maydell@linaro.org
This adds a feature bit indicating support of the (trivial) Jazelle
implementation if ARM_FEATURE_V6 is set or if the processor is arm926
or arm1026. This fixes the issue that any BXJ instruction will
result in an illegal_op. BXJ instructions will now check if the
architecture supports ARM_FEATURE_JAZELLE.
Signed-off-by: Portia Stephens <portia.stephens@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20170905211232.11092-1-portia.stephens@xilinx.com
[PMM: edited commit message and comment text a bit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the BXNS v8M instruction, which is like BX but will do a
jump-and-switch-to-NonSecure if the branch target address has bit 0
clear.
This is the first piece of code which implements "switch to the
other security state", so the commit also includes the code to
switch the stack pointers around, which is the only complicated
part of switching security state.
BLXNS is more complicated than just "BXNS but set the link register",
so we leave it for a separate commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-21-git-send-email-peter.maydell@linaro.org
Make the CFSR register banked if v8M security extensions are enabled.
Not all the bits in this register are banked: the BFSR
bits [15:8] are shared between S and NS, and we store them
in the NS copy of the register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-19-git-send-email-peter.maydell@linaro.org
Make the MMFAR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-18-git-send-email-peter.maydell@linaro.org
Make the CCR register banked if v8M security extensions are enabled.
This is slightly more complicated than the other "add banking"
patches because there is one bit in the register which is not
banked. We keep the live data in the NS copy of the register,
and adjust it on register reads and writes. (Since we don't
currently implement the behaviour that the bit controls, there
is nowhere else that needs to care.)
This patch includes the enforcement of the bits which are newly
RES1 in ARMv8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-17-git-send-email-peter.maydell@linaro.org
Make the MPU_CTRL register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-16-git-send-email-peter.maydell@linaro.org
Make the MPU_RNR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-15-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
We can freely add more items to vmstate_m_security without
breaking migration compatibility, because no CPU currently
has the ARM_FEATURE_M_SECURITY bit enabled and so this
subsection is not yet used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-14-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
Make the CONTROL register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-10-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Make the PRIMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of PRIMASK to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-8-git-send-email-peter.maydell@linaro.org
Make the BASEPRI register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of BASEPRI to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-7-git-send-email-peter.maydell@linaro.org
Now that MPU lookups can return different results for v8M
when the CPU is in secure vs non-secure state, we need to
have separate MMU indexes; add the secure counterparts
to the existing three M profile MMU indexes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-6-git-send-email-peter.maydell@linaro.org
As the first step in implementing ARM v8M's security extension:
* add a new feature bit ARM_FEATURE_M_SECURITY
* add the CPU state field that indicates whether the CPU is
currently in the secure state
* add a migration subsection for this new state
(we will add the Secure copies of banked register state
to this subsection in later patches)
* add a #define for the one new-in-v8M exception type
* make the CPU debug log print S/NS status
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-4-git-send-email-peter.maydell@linaro.org
As part of ARMv8M, we need to add support for the PMSAv8 MPU
architecture.
PMSAv8 differs from PMSAv7 both in register/data layout (for instance
using base and limit registers rather than base and size) and also in
behaviour (for example it does not have subregions); rather than
trying to wedge it into the existing PMSAv7 code and data structures,
we define separate ones.
This commit adds the data structures which hold the state for a
PMSAv8 MPU and the register interface to it. The implementation of
the MPU behaviour will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-2-git-send-email-peter.maydell@linaro.org
Mimicking gicv3-maintenance-interrupt, add the PMU's interrupt to
CPU state.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1500471597-2517-2-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a utility function for testing whether the CPU is in Handler
mode; this is just a check whether v7m.exception is non-zero, but
we do it in several places and it makes the code a bit easier
to read to not have to mentally figure out what the test is testing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-14-git-send-email-peter.maydell@linaro.org
We currently store the M profile CPU register state PRIMASK and
FAULTMASK in the daif field of the CPU state in its I and F
bits. This is a legacy from the original implementation, which
tried to share the cpu_exec_interrupt code between A profile
and M profile. We've since separated out the two cases because
they are significantly different, so now there is no common
code between M and A profile which looks at env->daif: all the
uses are either in A-only or M-only code paths. Sharing the state
fields now is just confusing, and will make things awkward
when we implement v8M, where the PRIMASK and FAULTMASK
registers are banked between security states.
Switch M profile over to using v7m.faultmask and v7m.primask
fields for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-10-git-send-email-peter.maydell@linaro.org
The M profile XPSR is almost the same format as the A profile CPSR,
but not quite. Define some XPSR_* macros and use them where we
definitely dealing with an XPSR rather than reusing the CPSR ones.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-9-git-send-email-peter.maydell@linaro.org
Remove the comment that claims that some MPU_CTRL bits are stored
in sctlr_el[1]. This has never been true since MPU_CTRL was added
in commit 29c483a506 -- the comment is a leftover from
Michael Davidsaver's original implementation, which I modified
not to use sctlr_el[1]; I forgot to delete the comment then.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-7-git-send-email-peter.maydell@linaro.org
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-19-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Almost all of the PMSAv7 state is in the pmsav7 substruct of
the ARM CPU state structure. The exception is the region
number register, which is in cp15.c6_rgnr. This exception
is a bit odd for M profile, which otherwise generally does
not store state in the cp15 substruct.
Rename cp15.c6_rgnr to pmsav7.rnr accordingly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1501153150-19984-4-git-send-email-peter.maydell@linaro.org
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move vcpu's associated numa_node field out of generic CPUState
into inherited classes that actually care about cpu<->numa mapping,
i.e: ARMCPU, PowerPCCPU, X86CPU.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1496161442-96665-6-git-send-email-imammedo@redhat.com>
[ehabkost: s/CPU is belonging to/CPU belongs to/ on comments]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Implement HFNMIENA support for the M profile MPU. This bit controls
whether the MPU is treated as enabled when executing at execution
priorities of less than zero (in NMI, HardFault or with the FAULTMASK
bit set).
Doing this requires us to use a different MMU index for "running
at execution priority < 0", because we will have different
access permissions for that case versus the normal case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1493122030-32191-14-git-send-email-peter.maydell@linaro.org
The M series MPU is almost the same as the already implemented R
profile MPU (v7 PMSA). So all we need to implement here is the MPU
register interface in the system register space.
This implementation has the same restriction as the R profile MPU
that it doesn't permit regions to be sized down smaller than 1K.
We also do not yet implement support for MPU_CTRL.HFNMIENA; this
bit should if zero disable use of the MPU when running HardFault,
NMI or with FAULTMASK set to 1 (ie at an execution priority of
less than zero) -- if the MPU is enabled we don't treat these
cases any differently.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Message-id: 1493122030-32191-13-git-send-email-peter.maydell@linaro.org
[PMM: Keep all the bits in mpu_ctrl field, rather than
using SCTLR bits for them; drop broken HFNMIENA support;
various cleanup]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM CPUs come in two flavours:
* proper MMU ("VMSA")
* only an MPU ("PMSA")
For PMSA, the MPU may be implemented, or not (in which case there
is default "always acts the same" behaviour, but it isn't guest
programmable).
QEMU is a bit confused about how we indicate this: we have an
ARM_FEATURE_MPU, but it's not clear whether this indicates
"PMSA, not VMSA" or "PMSA and MPU present" , and sometimes we
use it for one purpose and sometimes the other.
Currently trying to implement a PMSA-without-MPU core won't
work correctly because we turn off the ARM_FEATURE_MPU bit
and then a lot of things which should still exist get
turned off too.
As the first step in cleaning this up, rename the feature
bit to ARM_FEATURE_PMSA, which indicates a PMSA CPU (with
or without MPU).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1493122030-32191-5-git-send-email-peter.maydell@linaro.org
Make M profile use completely separate ARMMMUIdx values from
those that A profile CPUs use. This is a prelude to adding
support for the MPU and for v8M, which together will require
6 MMU indexes which don't map cleanly onto the A profile
uses:
non secure User
non secure Privileged
non secure Privileged, execution priority < 0
secure User
secure Privileged
secure Privileged, execution priority < 0
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1493122030-32191-4-git-send-email-peter.maydell@linaro.org
The M profile CPU's MPU has an awkward corner case which we
would like to implement with a different MMU index.
We can avoid having to bump the number of MMU modes ARM
uses, because some of our existing MMU indexes are only
used by non-M-profile CPUs, so we can borrow one.
To avoid that getting too confusing, clean up the code
to try to keep the two meanings of the index separate.
Instead of ARMMMUIdx enum values being identical to core QEMU
MMU index values, they are now the core index values with some
high bits set. Any particular CPU always uses the same high
bits (so eventually A profile cores and M profile cores will
use different bits). New functions arm_to_core_mmu_idx()
and core_to_arm_mmu_idx() convert between the two.
In general core index values are stored in 'int' types, and
ARM values are stored in ARMMMUIdx types.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1493122030-32191-3-git-send-email-peter.maydell@linaro.org
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1493816238-33120-3-git-send-email-imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
For M profile exception-return handling we'd like to generate different
code for some instructions depending on whether we are in Handler
mode or Thread mode. This isn't the same as "are we privileged
or user", so we need an extra bit in the TB flags to distinguish.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1491844419-12485-8-git-send-email-peter.maydell@linaro.org
The excnames[] array is defined in internals.h because we used
to use it from two different source files for handling logging
of AArch32 and AArch64 exception entry. Refactoring means that
it's now used only in arm_log_exception() in helper.c, so move
the array into that function.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1491821097-5647-1-git-send-email-peter.maydell@linaro.org
Recent changes have added new EXCP_ values to ARM but forgot
to update the excnames[] array which is used to provide
human-readable strings when printing information about the
exception for debug logging. Add the missing entries, and
add a comment to the list of #defines to help avoid the mistake
being repeated in future.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1491486340-25988-1-git-send-email-peter.maydell@linaro.org
The power state spec section 5.1.5 AFFINITY_INFO defines the
affinity info return values as
0 ON
1 OFF
2 ON_PENDING
I grepped QEMU for power_state to ensure that no assumptions
of OFF=0 were being made.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20170303123232.4967-1-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add gicv3state void pointer to CPUARMState struct
to store GICv3CPUState.
In case of usecase like CPU reset, we need to reset
GICv3CPUState of the CPU. In such scenario, this pointer
becomes handy.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487850673-26455-5-git-send-email-vijay.kilari@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
M profile doesn't implement ARM, and the architecturally required
behaviour for attempts to execute with the Thumb bit clear is to
generate a UsageFault with the CFSR INVSTATE bit set. We were
incorrectly implementing this as generating an UNDEFINSTR UsageFault;
fix this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Implement the exception return consistency checks
described in the v7M pseudocode ExceptionReturn().
Inspired by a patch from Michael Davidsaver's series, but
this is a reimplementation from scratch based on the
ARM ARM pseudocode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Having armv7m_nvic_acknowledge_irq() return the new value of
env->v7m.exception and its one caller assign the return value
back to env->v7m.exception is pointless. Just make the return
type void instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The M profile condition for when we can take a pending exception or
interrupt is not the same as that for A/R profile. The code
originally copied from the A/R profile version of the
cpu_exec_interrupt function only worked by chance for the
very simple case of exceptions being masked by PRIMASK.
Replace it with a call to a function in the NVIC code that
correctly compares the priority of the pending exception
against the current execution priority of the CPU.
[Michael Davidsaver's patchset had a patch to do something
similar but the implementation ended up being a rewrite.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
This enables the multi-threaded system emulation by default for ARMv7
and ARMv8 guests using the x86_64 TCG backend. This is because on the
guest side:
- The ARM translate.c/translate-64.c have been converted to
- use MTTCG safe atomic primitives
- emit the appropriate barrier ops
- The ARM machine has been updated to
- hold the BQL when modifying shared cross-vCPU state
- defer powerctl changes to async safe work
All the host backends support the barrier and atomic primitives but
need to provide same-or-better support for normal load/store
operations.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Pranith Kumar <bobby.prani@gmail.com>
When switching a new vCPU on we want to complete a bunch of the setup
work before we start scheduling the vCPU thread. To do this cleanly we
defer vCPU setup to async work which will run the vCPUs execution
context as the thread is woken up. The scheduling of the work will kick
the vCPU awake.
This avoids potential races in MTTCG system emulation.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds access support for PMINTENSET_EL1.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1486504171-26807-4-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to support Linux perf, which uses PMXEVTYPER register,
this patch adds read/write access support for PMXEVTYPER. The access
is CONSTRAINED UNPREDICTABLE when PMSELR is not 0x1f. Additionally
this patch adds support for PMXEVTYPER_EL0.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1486504171-26807-3-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for AArch64 register PMSELR_EL0. The existing
PMSELR definition is revised accordingly.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: Moved #ifndef CONFIG_USER_ONLY to cover new regdefs]
Message-id: 1486504171-26807-2-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new "cfgend" property which selects whether the CPU resets into
big-endian mode or not. This setting affects whether we reset with
SCTLR_B (ARMv6 and earlier) or SCTLR_EE (ARMv7 and later) set.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: 11420d1c49636c1790e60578ee996e51f0f0b835.1484929304.git.julian@codesourcery.com
[PMM: use error_report_err() rather than error_report();
move the integratorcp changes to their own patch;
drop an unnecessary extra #include;
rephrase commit message accordingly;
move setting of reset_sctlr above registration of cpregs
so it actually has an effect]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For v7M attempts to access a nonexistent coprocessor are reported
differently from plain undefined instructions (as UsageFaults of type
NOCP rather than type UNDEFINSTR). Split them out into a new
EXCP_NOCP so we can report the FSR value correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-8-git-send-email-peter.maydell@linaro.org
Add the structure fields, VMState fields, reset code and macros for
the v7M system control registers CCR, CFSR, HFSR, DFSR, MMFAR and
BFAR.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-4-git-send-email-peter.maydell@linaro.org
We only use the IS_M() macro in two places, and it's a bit of a
namespace grab to put in cpu.h. Drop it in favour of just explicitly
calling arm_feature() in the places where it was used.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1485285380-10565-2-git-send-email-peter.maydell@linaro.org
The v7m CONTROL register bit 1 is SPSEL, which indicates
the stack being used. We were storing this information
not in v7m.control but in the separate v7m.other_sp
structure field. Unfortunately, the code handling reads
of the CONTROL register didn't take account of this, and
so if SPSEL was updated by an exception entry or exit then
a subsequent guest read of CONTROL would get the wrong value.
Using a separate structure field doesn't really gain us
anything in efficiency, so drop this unnecessary complexity
in favour of simply storing all the bits in v7m.control.
This is a migration compatibility break for M profile
CPUs only.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-6-git-send-email-peter.maydell@linaro.org
[PMM: rewrote commit message;
use deposit32(); use FIELD to define constants for
masking and shifting of CONTROL register fields
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable the ARM_FEATURE_EL2 bit on Cortex-A52 and
Cortex-A57, since this is all now sufficiently implemented
to work with the GICv3. We provide the usual CPU property
to disable it for backwards compatibility with the older
virt boards.
In this commit, we disable the EL2 feature on the
virt and ZynpMP boards, so there is no overall effect.
Another commit will expose a board-level property to
allow the user to enable EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-18-git-send-email-peter.maydell@linaro.org
Add fields to the ARMCPU structure to allow CPU classes to
specify the configurable aspects of their GIC CPU interface.
In particular, the virtualization support allows different
values for number of list registers, priority bits and
preemption bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-6-git-send-email-peter.maydell@linaro.org
The GICv3 support for virtualization includes an outbound
maintenance interrupt signal which is asserted when the
CPU interface wants to signal to the hypervisor that it
needs attention. Expose this as an outbound GPIO line from
the CPU object which can be wired up as a physical interrupt
line by the board code (as we do already for the CPU timers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-4-git-send-email-peter.maydell@linaro.org
It is a common thing amongst the various cpu reset functions want to
flush the SoftMMU's TLB entries. This is done either by calling
tlb_flush directly or by way of a general memset of the CPU
structure (sometimes both).
This moves the tlb_flush call to the common reset function and
additionally ensures it is only done for the CONFIG_SOFTMMU case and
when tcg is enabled.
In some target cases we add an empty end_of_reset_fields structure to the
target vCPU structure so have a clear end point for any memset which
is resetting value in the structure before CPU_COMMON (where the TLB
structures are).
While this is a nice clean-up in general it is also a precursor for
changes coming to cputlb for MTTCG where the clearing of entries
can't be done arbitrarily across vCPUs. Currently the cpu_reset
function is usually called from the context of another vCPU as the
architectural power up sequence is run. By using the cputlb API
functions we can ensure the right behaviour in the future.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
ARM1176 CPUs have TrustZone support and can use the Vector Base
Address Register, but currently, qemu only adds VBAR support to ARMv7
CPUs. Fix this by adding a new feature ARM_FEATURE_VBAR which can used
for ARMv7 and ARM1176 CPUs.
The VBAR feature is always set for ARMv7 because some legacy boards
require it even if this is not architecturally correct.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1481810970-9692-1-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
