Like brcond2, use tcg_high_cond. Use movcc instead of branches.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Avoid speculatively computing flags before every potentially trapping
operation and instead do the flags computation when a trap actually
occurs. This gives approximately 30% speedup in emulation.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Now that save_state never ends a BB, we don't need to copy
values into local temps around it.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* pmaydell/arm-devs.for-upstream:
arm_gic: Rename gic_state to GICState
zynq_slcr: Fixed ResetValues enum
versatilepb: add gpio pl061 support
hw/ds1338: Implement state save/restore
hw/ds1338: Remove 'now' field from state struct
hw/ds1338: Recapture current time when register pointer wraps around
hw/ds1338: Fix mishandling of register pointer
hw/arm_gic.c: Fix improper DPRINTF output.
cadence_ttc: Fix 'clear on read' behavior
* stefanha/trivial-patches:
vnc: fix "info vnc" with "-vnc ..., reverse=on"
sheepdog: use bool for boolean variables
configure: Tidy up remnants of non-64-bit physaddrs
* kraxel/usb.67:
uhci: Raise interrupt when requested even for non active tds
usb-redir: Don't make migration fail in none seamless case
usb-redir: Change usbredir_open_chardev into usbredir_create_parser
* mdroth/qga-pull-10-9-12:
qemu-ga: ga_open_pidfile(): add new line to pidfile
qemu-ga: use state dir from CONFIG_QEMU_LOCALSTATEDIR
configure: add --localstatedir
* stefanha/net:
net: consolidate NetClientState header files into one
virtio-net: update nc.link_down in virtio_net_load()
e1000: update nc.link_down in e1000_post_load()
rtl8139: implement 8139cp link status
* spice/spice.v61:
qxl: set default revision to 4
spice: raise requirement to 0.12
hw/qxl: qxl_dirty_surfaces: use uintptr_t
hw/qxl: fix condition for exiting guest_bug
hw/qxl: exit on failure to register qxl interface
qxl: fix range check for rev3 io commands.
qxl/update_area_io: cleanup invalid parameters handling
qxl: always update displaysurface on resize
Rename the gic_state struct to match QEMU's coding style conventions
for structure names, since the impending KVM-for-ARM patches will
create another subclass of it. This patch was created using:
sed -i 's/gic_state/GICState/g' hw/arm_gic.c hw/arm_gic_common.c \
hw/arm_gic_internal.h hw/armv7m_nvic.c
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a gap in the reset region of the address space at offset 0x208. This
throws out all these enum values by one when translating them to address offsets.
Fixed by putting the corresponding gap in the enum as well.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement state save/restore for the DS1338. This requires
the usual minor adjustment of types in the state struct to
get fixed-width ones with vmstate macros.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'struct tm now' field in the state structure is in fact only
ever used as a temporary (the actual RTC state is held in 'offset').
Remove it from the state structure in favour of using local variables
to avoid confusion about whether it needs to be saved on migration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DS1338 datasheet documents that the current time is captured into
the secondary registers when the register pointer wraps round to zero
as well as at a START condition. Implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct several deficiencies in the handling of the register pointer:
* it should wrap around after 0x3f, not 0xff
* guard against the caller handing us an out of range pointer
(on h/w this can never happen, because only a 7 bit value is
transferred over the I2C bus)
* there was confusion over whether nvram[] holds only the 56 bytes
of guest-accessible NVRAM, or also the secondary registers
which hold the value of the clock captured at the start of a
multibyte read. Correct to consistently be the latter, by fixing
the array size and the offset used for NVRAM writes.
* ds1338_send was attempting to use 'data' as both the data and
the register offset simultaneously, which meant that writes to
any register were broken; fix to use the register pointer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s->cpu_enabled is an array, so s->cpu_enabled ? "En" : "Dis" returns
"En" always. We should use s->cpu_enabled[cpu] here.
Signed-off-by: Evgeny Voevodin <e.voevodin@samsung.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A missing call to qemu_set_irq() when reading the IRQ register
required SW to write to the IRQ register to acknowledge an
interrupt. With this patch the behavior is fixed:
- Reading the interrupt register clears it and updates the timers
interrupt status
- Writes to the interrupt register are ignored
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When reverse connection is in use, there is no active VNC server
socket. Because of this, getsockopt(-1, ...) is attempted and
the following error is emitted:
$ socat TCP-LISTEN:5900,reuseaddr TCP-LISTEN:5901,reuseaddr &
$ x86_64-softmmu/qemu-system-x86_64 -vnc localhost:5900,reverse -monitor stdio
QEMU 1.2.50 monitor - type 'help' for more information
(qemu) info vnc
An undefined error has occurred
Because however the host, family, service and auth fields are
optional, we can just exit if there is no active server socket.
$ x86_64-softmmu/qemu-system-x86_64 -vnc localhost:5900,reverse -monitor stdio
QEMU 1.2.50 monitor - type 'help' for more information
(qemu) info vnc
Server:
Client:
address: 127.0.0.1:5900
x509_dname: none
username: none
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tidy up some remnants of code to support non-64-bit physaddrs
which were accidentally omitted from commit 4be403c8.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
According to the spec we must raise an interrupt when one is requested
even for non active tds.
Linux depends on this, for bulk transfers it runs an inactivity timer
to work around a bug in early uhci revisions, when we take longer then
200 ms to process a packet, this timer goes of, and as part of the
handling Linux then unlinks the qh, and relinks it after the frindex
has increased by atleast 1, the problem is Linux only checks for the
frindex increases on an interrupt, and we don't send that, causing
the qh to go inactive for more then 32 frames, at which point we
consider the packet cancelled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Instead simple disconnect the device like host redirection does on
migration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Added helper function to automatically connect SPI slaves based on the QOM child
nodes of a device. A SSI master device can call this routine to automatically
hook-up all child nodes to its SPI bus.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added maintainership for SSI, M25P80 and the Xilinx SPI controllers.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added the two SPI controllers to the zynq machine model. Attached two SPI flash
devices to each controller.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added device model for the Xilinx Zynq SPI controller (SPIPS).
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added SPI controller to the reference design, with two n25q128 spi-flashes
connected.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Removed the explicit SSI mux and wired the CS line directly up to the SSI
devices.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Allow multiple qdev_init_gpio_in() calls for the one device. The first call will
define GPIOs 0-N-1, the next GPIOs N- ... . Allows different GPIOs to be handled
with different handlers. Needed when two levels of the QOM class heirachy both
define GPIO functionality, as a single GPIO handler with an index selecter is
not possible.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Slave creation function that can be used to create an SSI slave without
qdev_init() being called. This give machine models a chance to set properties.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Added default CS behaviour for SSI slaves. SSI devices can set a property
to enable CS behaviour which will create a GPIO on the device which is the
CS. Tristating of the bus on SSI transfers is implemented.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Removed assertion that only one device is attached to the SSI bus.
When multiple devices are attached, all slaves have their transfer function
called for transfers. Each device is responsible for knowing whether or not its
CS is active, and if not returning 0. The returned data is the logical or of
all responses from the (mulitple) devices.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
FHS requires that pid files should end with a new line. Also change to
snprintf() while there.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Has the side effect of changing the default directory used to
save the freeze status file from /tmp to ${prefix}/var/run.
This is a beneficial change for two reasons:
1. FHS states that programs must not assume that files in /tmp will
still exist between invocations of the program. This defeats
the purpose of the freeze status file
2. FHS dictates that /var/run must be cleaned on boot, this
ensures that a stale freeze status file will be removed on boot
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Next commit wants to use it.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
DO_UPCAST is supposed to translate from the first member of a struct to
that struct, not from arbitrary ones. And it (usually) breaks the build
when neglecting this rule. Use container_of to fix the build breakage
and likely also the runtime behavior.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
aw: runtime behavior is actually the same, but clearly misuse of DO_UPCAST
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Blue Swirl reports that Clang doesn't like the structure we define to
avoid dynamic allocation for a number of calls to VFIO_DEVICE_SET_IRQS.
Adding an element after a variable sized type is a GNU extension.
Switch back to dynamic allocation, which really isn't a problem since
this is only done on interrupt setup changes.
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Take what we've learned from pci-assign and apply it to vfio-pci.
On reset, disable previous interrupt config, perform a device
reset if available, re-enable INTx, and disable memory regions on
the device to prevent continuing DMA.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This was a misinterpretation of the spec, hardware doesn't get to
specify how many were actually enabled through this field.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
