The category of the vmmouse device is not set, put it into the 'input'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201130083630.2520597-4-ganqixin@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
'drivers_blacklisted' is never accessed, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20210202155644.998812-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When SEV-ES is enabled, it is not possible modify the guests register
state after it has been initially created, encrypted and measured.
Normally, an INIT-SIPI-SIPI request is used to boot the AP. However, the
hypervisor cannot emulate this because it cannot update the AP register
state. For the very first boot by an AP, the reset vector CS segment
value and the EIP value must be programmed before the register has been
encrypted and measured. Search the guest firmware for the guest for a
specific GUID that tells Qemu the value of the reset vector to use.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <22db2bfb4d6551aed661a9ae95b4fdbef613ca21.1611682609.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When AMD's SEV memory encryption is in use, flash memory banks (which are
initialed by pc_system_flash_map()) need to be encrypted with the guest's
key, so that the guest can read them.
That's abstracted via the kvm_memcrypt_encrypt_data() callback in the KVM
state.. except, that it doesn't really abstract much at all.
For starters, the only call site is in code specific to the 'pc'
family of machine types, so it's obviously specific to those and to
x86 to begin with. But it makes a bunch of further assumptions that
need not be true about an arbitrary confidential guest system based on
memory encryption, let alone one based on other mechanisms:
* it assumes that the flash memory is defined to be encrypted with the
guest key, rather than being shared with hypervisor
* it assumes that that hypervisor has some mechanism to encrypt data into
the guest, even though it can't decrypt it out, since that's the whole
point
* the interface assumes that this encrypt can be done in place, which
implies that the hypervisor can write into a confidential guests's
memory, even if what it writes isn't meaningful
So really, this "abstraction" is actually pretty specific to the way SEV
works. So, this patch removes it and instead has the PC flash
initialization code call into a SEV specific callback.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
gcc is not smart enough to figure out length was validated before use as
strncpy limit, resulting in this warning:
inlined from ‘virt_set_oem_table_id’ at ../../hw/arm/virt.c:2197:5:
/usr/include/aarch64-linux-gnu/bits/string_fortified.h:106:10: error:
‘__builtin_strncpy’ specified bound depends on the length of the
source argument [-Werror=stringop-overflow=]
Simplify things by using a constant limit instead.
Fixes: 97fc5d507fca ("acpi: Permit OEM ID and OEM table ID fields to be changed")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Qemu's ACPI table generation sets the fields OEM ID and OEM table ID
to "BOCHS " and "BXPCxxxx" where "xxxx" is replaced by the ACPI
table name.
Some games like Red Dead Redemption 2 seem to check the ACPI OEM ID
and OEM table ID for the strings "BOCHS" and "BXPC" and if they are
found, the game crashes(this may be an intentional detection
mechanism to prevent playing the game in a virtualized environment).
This patch allows you to override these default values.
The feature can be used in this manner:
qemu -machine oem-id=ABCDEF,oem-table-id=GHIJKLMN
The oem-id string can be up to 6 bytes in size, and the
oem-table-id string can be up to 8 bytes in size. If the string are
smaller than their respective sizes they will be padded with space.
If either of these parameters is not set, the current default values
will be used for the one missing.
Note that the the OEM Table ID field will not be extended with the
name of the table, but will use either the default name or the user
provided one.
This does not affect the -acpitable option (for user-defined ACPI
tables), which has precedence over -machine option.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210119003216.17637-3-posteuca@mutex.one>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They have been deprecated since QEMU v5.0, time to remove them now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210203171832.483176-2-thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
To ease the PCI device addition in next patches, split the code as follows:
- generic code (read/write/setup) is being kept in pvpanic.c
- ISA dependent code moved to pvpanic-isa.c
Also, rename:
- ISA_PVPANIC_DEVICE -> PVPANIC_ISA_DEVICE.
- TYPE_PVPANIC -> TYPE_PVPANIC_ISA.
- MemoryRegion io -> mr.
- pvpanic_ioport_* in pvpanic_*.
Update the build system with the new files and config structure.
Signed-off-by: Mihai Carabas <mihai.carabas@oracle.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AML needs Address Translation offset to describe how a bridge translates
addresses accross the bridge when using an address descriptor, and
especially on ARM, the translation offset of pio resource is usually
non zero.
Therefore, it's necessary to pass offset for pio, mmio32, mmio64 and bus
number into build_crs.
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20210114100643.10617-4-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We already have a generic PCI_SLOT() macro in "hw/pci/pci.h"
to extract the PCI slot identifier, use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Paul Durrant <paul@xen.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20201012124506.3406909-5-philmd@redhat.com>
Enable removing tcg/$tcg_arch from the include path when TCG is disabled.
Move translate-all.h to include/exec, since stubs exist for the functions
defined therein.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201026143028.3034018-6-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds support the kernel-irqchip option for
WHPX with on or off value. 'split' value is not supported
for the option. The option only works for the latest version
of Windows (ones that are coming out on Insiders). The
change maintains backward compatibility on older version of
Windows where this option is not supported.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Message-Id: <SN4PR2101MB0880B13258DA9251F8459F4DC0170@SN4PR2101MB0880.namprd21.prod.outlook.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The IOAPIC has an 'Extended Destination ID' field in its RTE, which maps
to bits 11-4 of the MSI address. Since those address bits fall within a
given 4KiB page they were historically non-trivial to use on real hardware.
The Intel IOMMU uses the lowest bit to indicate a remappable format MSI,
and then the remaining 7 bits are part of the index.
Where the remappable format bit isn't set, we can actually use the other
seven to allow external (IOAPIC and MSI) interrupts to reach up to 32768
CPUs instead of just the 255 permitted on bare metal.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <78097f9218300e63e751e077a0a5ca029b56ba46.camel@infradead.org>
[Fix UBSAN warning. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Create second ioapic, route virtio-mmio IRQs to it,
allow more virtio-mmio devices (24 instead of 8).
Needs ACPI, enabled by default, can be turned off
using -machine ioapic2=off
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-8-kraxel@redhat.com
With the improved gsi_handler() we don't need
our private version any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-7-kraxel@redhat.com
Allows to move them in case we have enough
irq lines available.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-6-kraxel@redhat.com
This will allow to increase the number of transports in
case we have enough irq lines available for them all.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-5-kraxel@redhat.com
Add ioapic_init_secondary to initialize it, wire up
in gsi handling and acpi apic table creation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Message-id: 20201203105423.10431-4-kraxel@redhat.com
Rewrite function to use switch() for IRQ number mapping.
Check i8259_irq exists before raising it so the function
also works in case no i8259 (aka pic) is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20201203105423.10431-3-kraxel@redhat.com
Keep CPU hotunplug with SMI disabled on 5.2 and older and enable
it by default on newer machine types.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-9-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
if firmware and QEMU negotiated CPU hotunplug support, generate
_EJ0 method so that it will mark CPU for removal by firmware and
pass control to it by triggering SMI.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201207140739.3829993-4-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At Hewlett Packard Inc. we have a need for increased fw size to enable testing of our custom fw.
Rebase v6 patch to d73c46e4
Signed-off-by: Erich McMillan <erich.mcmillan@hp.com>
Message-Id: <20201208155338.14-1-erich.mcmillan@hp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 6.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20201109173928.1001764-1-cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract crs build form acpi_build.c, the function could also be used
to build the crs for pxbs for arm. The resources are composed by two parts:
1. The bar space of pci-bridge/pcie-root-ports
2. The resources needed by devices behind PXBs.
The base and limit of memory/io are obtained from the config via two APIs:
pci_bridge_get_base and pci_bridge_get_limit
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-5-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extract extra pci roots addition from pc machine, which could be used by
other machines.
In order to make uefi get the extra roots, it is necessary to write extra
roots into fw_cfg. And only if the uefi knows there are extra roots,
the config spaces of devices behind the root could be obtained.
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Message-Id: <20201119014841.7298-3-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although they didn't reach the notifier because of the filtering in
memory_region_notify_iommu_one, the vt-d was still splitting huge
memory invalidations in chunks. Skipping it.
This improves performance in case of netperf with vhost-net:
* TCP_STREAM: From 1923.6Mbit/s to 2175.13Mbit/s (13%)
* TCP_RR: From 8464.73 trans/s to 8932.703333 trans/s (5.5%)
* UDP_RR: From 8562.08 trans/s to 9005.62/s (5.1%)
* UDP_STREAM: No change observed (insignificant 0.1% improvement)
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-5-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This allows us to differentiate between regular IOMMU map/unmap events
and DEVIOTLB unmap. Doing so, notifiers that only need device IOTLB
invalidations will not receive regular IOMMU unmappings.
Adapt intel and vhost to use it.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-4-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This way we can tell between regular IOMMUTLBEntry (entry of IOMMU
hardware) and notifications.
In the notifications, we set explicitly if it is a MAPs or an UNMAP,
instead of trusting in entry permissions to differentiate them.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Previous name didn't reflect the iommu operation.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20201116165506.31315-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
GCC 9.3.0 thinks that 'method' can be left uninitialized. This code
is already in the "if (bsel || pcihp_bridge_en)" block statement,
but it isn't smart enough to figure it out.
Restrict the code to be used only in the "if (bsel || pcihp_bridge_en)"
block statement to fix (on Ubuntu):
../hw/i386/acpi-build.c: In function 'build_append_pci_bus_devices':
../hw/i386/acpi-build.c:496:9: error: 'method' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
496 | aml_append(parent_scope, method);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: df4008c9c5 ("piix4: don't reserve hw resources when hotplug is off globally")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201108204535.2319870-4-philmd@redhat.com>
Message-Id: <20201110192316.26397-8-alex.bennee@linaro.org>
Just a bunch of bugfixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl+cCq8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpKWkH/0qq+u2z/q0KYzmodcdW2eFNsvKF2e+Dz3Af
zZGMREH93DsKAQ2k3t84sz2RAaAP45cCqrq+v8kSzmpaC7GqKYA/VceeLwy8e6Eu
YKvu5QixrOVTpNg2QV/w44ywgtA4NbWy5Fr9S4qhzPyyD/gtE609weZ1vQnSFT7B
Gg4vr1lcqskwYTH7sh+bpsDTUeANr7QaknWKnaomroz+IUO8m9ig6RKtegaXhQCj
xswI4458S3nklqnoGMa56j46VYwft8YHO1lBiR1WefTHylknyng9Tdvf9G5mnzVg
wyrMTuT36lMXIa5KcSZeECIt2ZUT6KSSjWzEKZNXL5lS3gfUo7o=
=powp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,vhost,virtio: misc fixes
Just a bunch of bugfixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 30 Oct 2020 12:44:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
intel_iommu: Fix two misuse of "0x%u" prints
virtio: skip guest index check on device load
vhost-blk: set features before setting inflight feature
pci: Disallow improper BAR registration for type 1
pci: Change error_report to assert(3)
pci: advertise a page aligned ATS
pc: Implement -no-hpet as sugar for -machine hpet=on
vhost: Don't special case vq->used_phys in vhost_get_log_size()
pci: Assert irqnum is between 0 and bus->nirqs in pci_bus_change_irq_level
hw/pci: Extract pci_bus_change_irq_level() from pci_change_irq_level()
hw/virtio/vhost-vdpa: Fix Coverity CID 1432864
acpi/crs: Support ranges > 32b for hosts
acpi/crs: Prevent bad ranges for host bridges
vhost-vsock: set vhostfd to non-blocking mode
vhost-vdpa: negotiate VIRTIO_NET_F_STATUS with driver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Dave magically found this. Fix them with "0x%x".
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201019173922.100270-1-peterx@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Get rid of yet another global variable.
The default will be hpet=on only if CONFIG_HPET=y.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20201021144716.1536388-1-ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to PCIe spec 5.0 Type 1 header space Base Address Registers
are defined by 7.5.1.2.1 Base Address Registers (same as Type 0). The
_CRS region should allow for the same range (up to 64b). Prior to this
change, any host bridge utilizing more than 32b for the BAR would have
the address truncated and likely lead to conflicts when the operating
systems reads the _CRS object.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201026193924.985014-2-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Prevent _CRS resources being quietly chopped off and instead throw an
assertion. _CRS is used by host bridges to declare regions of io and/or
memory that they consume. On some (all?) platforms the host bridge
doesn't have PCI header space and so they need some way to convey the
information.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201026193924.985014-1-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
pc_dimm_plug() doesn't use it. It only aborts on error.
Drop @errp and adapt the callers accordingly.
[dwg: Removed unused label to fix compile]
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160309728447.2739814.12831204841251148202.stgit@bahia.lan>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Setting x86ms->pci_irq_mask to zero has the same effect,
so we don't need the has_pci argument any more.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-6-kraxel@redhat.com
Makes sure the PCI interrupt overrides are added to the
APIC table in case PCIe is enabled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-5-kraxel@redhat.com
Add a variable to x86 machine state instead of
hard-coding the PCI interrupts.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20201016113835.17465-4-kraxel@redhat.com
