This adds two new machines, both supported by OpenBMC:
- npcm750-evb: Nuvoton NPCM750 Evaluation Board.
- quanta-gsj: A board with a NPCM730 chip.
They rely on the NPCM7xx SoC device to do the heavy lifting. They are
almost completely identical at the moment, apart from the SoC type,
which currently only changes the reset contents of one register
(GCR.MDLR), but they might grow apart a bit more as more functionality
is added.
Both machines can boot the Linux kernel into /bin/sh.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-6-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Nuvoton NPCM7xx SoC family are used to implement Baseboard
Management Controllers in servers. While the family includes four SoCs,
this patch implements limited support for two of them: NPCM730 (targeted
for Data Center applications) and NPCM750 (targeted for Enterprise
applications).
This patch includes little more than the bare minimum needed to boot a
Linux kernel built with NPCM7xx support in direct-kernel mode:
- Two Cortex-A9 CPU cores with built-in periperhals.
- Global Configuration Registers.
- Clock Management.
- 3 Timer Modules with 5 timers each.
- 4 serial ports.
The chips themselves have a lot more features, some of which will be
added to the model at a later stage.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-5-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 SoCs have three timer modules each holding five
timers and some shared registers (e.g. interrupt status).
Each timer runs at 25 MHz divided by a prescaler, and counts down from a
configurable initial value to zero. When zero is reached, the interrupt
flag for the timer is set, and the timer is disabled (one-shot mode) or
reloaded from its initial value (periodic mode).
This implementation is sufficient to boot a Linux kernel configured for
NPCM750. Note that the kernel does not seem to actually turn on the
interrupts.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-4-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enough functionality to boot the Linux kernel has been implemented. This
includes:
- Correct power-on reset values so the various clock rates can be
accurately calculated.
- Clock enables stick around when written.
In addition, a best effort attempt to implement SECCNT and CNTR25M was
made even though I don't think the kernel needs them.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-3-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a device model for the System Global Control Registers in the
NPCM730 and NPCM750 BMC SoCs.
This is primarily used to enable SMP boot (the boot ROM spins reading
the SCRPAD register) and DDR memory initialization; other registers are
best effort for now.
The reset values of the MDLR and PWRON registers are determined by the
SoC variant (730 vs 750) and board straps respectively.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-2-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl9aa4YACgkQIeENKd+X
cFTJjgf5ASfFIO5HqP1l80/UM5Pswyq0IROZDq0ItZa6U4EPzLXoE2N0POriIj4h
Ds2JbMg0ORDqY0VbSxHlgYHMgJ9S6cuVOMnATsPG0d2jaJ3gSxLBu5k/1ENqe+Vw
sSYXZv5uEAUfOFz99zbuhKHct5HzlmBFW9dVHdflUQS+cRgsSXq27mz1BvZ8xMWl
lMhwubqdoNx0rOD3vKnlwrxaf54DcJ2IQT3BtTCjEar3tukdNaLijAuwt2hrFyr+
IwpeFXA/NWar+mXP3M+BvcLaI33j73/ac2+S5SJuzHGp/ot5nT5gAuq3PDEjHMeS
t6z9Exp776VXxNE2iUA5NB65Yp3/6w==
=07oA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20200910' into staging
This PR includes multiple fixes and features for RISC-V:
- Fixes a bug in printing trap causes
- Allows 16-bit writes to the SiFive test device. This fixes the
failure to reboot the RISC-V virt machine
- Support for the Microchip PolarFire SoC and Icicle Kit
- A reafactor of RISC-V code out of hw/riscv
# gpg: Signature made Thu 10 Sep 2020 19:08:06 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20200910: (30 commits)
hw/riscv: Sort the Kconfig options in alphabetical order
hw/riscv: Drop CONFIG_SIFIVE
hw/riscv: Always build riscv_hart.c
hw/riscv: Move sifive_test model to hw/misc
hw/riscv: Move sifive_uart model to hw/char
hw/riscv: Move riscv_htif model to hw/char
hw/riscv: Move sifive_plic model to hw/intc
hw/riscv: Move sifive_clint model to hw/intc
hw/riscv: Move sifive_gpio model to hw/gpio
hw/riscv: Move sifive_u_otp model to hw/misc
hw/riscv: Move sifive_u_prci model to hw/misc
hw/riscv: Move sifive_e_prci model to hw/misc
hw/riscv: sifive_u: Connect a DMA controller
hw/riscv: clint: Avoid using hard-coded timebase frequency
hw/riscv: microchip_pfsoc: Hook GPIO controllers
hw/riscv: microchip_pfsoc: Connect 2 Cadence GEMs
hw/arm: xlnx: Set all boards' GEM 'phy-addr' property value to 23
hw/net: cadence_gem: Add a new 'phy-addr' property
hw/riscv: microchip_pfsoc: Connect a DMA controller
hw/dma: Add SiFive platform DMA controller emulation
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/riscv/trace-events
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a platform DMA controller with 4 DMA
channels. This connects the exsiting SiFive PDMA model to the SoC,
and adds its device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-17-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timestamp is using a hard-coded timebase
frequency value SIFIVE_CLINT_TIMEBASE_FREQ. This might not be
true for all boards.
Add a new 'timebase-freq' property to the CLINT device, and
update various functions to accept this as a parameter.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-16-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 3 GPIOs controllers. It seems
enough to create unimplemented devices to cover their register
spaces at this point.
With this commit, QEMU can boot to U-Boot (2nd stage bootloader)
all the way to the Linux shell login prompt, with a modified HSS
(1st stage bootloader).
For detailed instructions on how to create images for the Icicle
Kit board, please check QEMU RISC-V WiKi page at:
https://wiki.qemu.org/Documentation/Platforms/RISCV
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-15-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 2 Candence GEMs to provide
IEEE 802.3 standard-compliant 10/100/1000 Mbps ethernet interface.
On the Icicle Kit board, GEM0 connects to a PHY at address 8 while
GEM1 connects to a PHY at address 9.
The 2nd stage bootloader (U-Boot) is using GEM1 by default, so we
must specify 2 '-nic' options from the command line in order to get
a working ethernet.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-14-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the PHY address of the PHY connected to GEM is hard-coded
to either 23 (BOARD_PHY_ADDRESS) or 0. This might not be the case for
all boards. Add a new 'phy-addr' property so that board can specify
the PHY address for each GEM instance.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA
controller to move the 2nd stage bootloader in the system memory.
Let's connect a DMA controller to Microchip PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates a DMA engine that supports:
* Independent concurrent DMA transfers using 4 DMA channels
* Generation of interrupts on various conditions during execution
which is actually an IP reused from the SiFive FU540 chip.
This creates a model to support both polling and interrupt modes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates one Cadence SDHCI controller.
On the Icicle Kit board, one eMMC chip and an external SD card
connect to this controller depending on different configuration.
As QEMU does not support eMMC yet, we just emulate the SD card
configuration. To test this, the Hart Software Services (HSS)
should choose the SD card configuration:
$ cp boards/icicle-kit-es/def_config.sdcard .config
$ make BOARD=icicle-kit-es
The SD card image can be built from the Yocto BSP at:
https://github.com/polarfire-soc/meta-polarfire-soc-yocto-bsp
Note the generated SD card image should be resized before use:
$ qemu-img resize /path/to/sdcard.img 4G
Launch QEMU with the following command:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit -sd sdcard.img
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Cadence SD/SDIO/eMMC Host Controller (SD4HC) is an SDHCI compatible
controller. The SDHCI compatible registers start from offset 0x200,
which are called Slot Register Set (SRS) in its datasheet.
This creates a Cadence SDHCI model built on top of the existing
generic SDHCI model. Cadence specific Host Register Set (HRS) is
implemented to make guest software happy.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC has 5 MMUARTs, and the Icicle Kit board
wires 4 of them out. Let's connect all 5 MMUARTs.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC MMUART is ns16550 compatible, with some
additional registers. Create a simple MMUART model built on top
of the existing ns16550 model.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an initial support for Microchip PolarFire SoC Icicle Kit.
The Icicle Kit board integrates a PolarFire SoC, with one SiFive's
E51 plus four U54 cores and many on-chip peripherals and an FPGA.
For more details about Microchip PolarFire Soc, please see:
https://www.microsemi.com/product-directory/soc-fpgas/5498-polarfire-soc-fpga
Unlike SiFive FU540, the RISC-V core resect vector is at 0x20220000.
The following perepherals are created as an unimplemented device:
- Bus Error Uint 0/1/2/3/4
- L2 cache controller
- SYSREG
- MPUCFG
- IOSCBCFG
More devices will be added later.
The BIOS image used by this machine is hss.bin, aka Hart Software
Services, which can be built from:
https://github.com/polarfire-soc/hart-software-services
To launch this machine:
$ qemu-system-riscv64 -nographic -M microchip-icicle-kit
The memory is set to 1 GiB by default to match the hardware.
A sanity check on ram size is performed in the machine init routine
to prompt user to increase the RAM size to > 1 GiB when less than
1 GiB ram is detected.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RISC-V machines do not instantiate RISC-V CPUs directly, instead
they do that via the hart array. Add a new property for the reset
vector address to allow the value to be passed to the CPU, before
CPU is realized.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200902224311.1321159-49-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make the type name constant consistent with the name of
the type checking macro.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200902224311.1321159-6-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This looks like a copy/paste mistake: the instance type checking
macro for TYPE_GPEX_ROOT_DEVICE was named MCH_PCI_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Separate run of the TypeCheckMacro converter using the --force
flag, for the cases where typedefs weren't found in the same
header nor in typedefs.h.
Generated initially using:
$ ./scripts/codeconverter/converter.py --force -i \
--pattern=TypeCheckMacro $(git grep -l '' -- '*.[ch]')
Then each case was manually reviewed, and a comment was added
indicating what's unusual about those type checking
macros/functions. Despite not following the usual pattern, the
changes in this patch were found to be safe.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200831210740.126168-15-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The work to be done in h_home_node_associativity() intersects
with what is already done in spapr_numa_fixup_cpu_dt(). This
patch creates a new helper, spapr_numa_get_vcpu_assoc(), to
be used for both spapr_numa_fixup_cpu_dt() and
h_home_node_associativity().
While we're at it, use memcpy() instead of loop assignment
to created the returned array.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200904172422.617460-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In a similar fashion as the previous patch, let's move the
handling of ibm,associativity-lookup-arrays from spapr.c to
spapr_numa.c. A spapr_numa_write_assoc_lookup_arrays() helper was
created, and spapr_dt_dynamic_reconfiguration_memory() can now
use it to advertise the lookup-arrays.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200903220639.563090-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Vcpus have an additional paramenter to be appended, vcpu_id. This
also changes the size of the of property itself, which is being
represented in index 0 of numa_assoc_array[cpu->node_id],
and defaults to MAX_DISTANCE_REF_POINTS for all cases but
vcpus.
All this logic makes more sense in spapr_numa.c, where we handle
everything NUMA and associativity. A new helper spapr_numa_fixup_cpu_dt()
was added, and spapr.c uses it the same way as it was using the former
spapr_fixup_cpu_numa_dt().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200903220639.563090-3-danielhb413@gmail.com>
[dwg: Correct uint to int type, which can break windows builds]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The next step to centralize all NUMA/associativity handling in
the spapr machine is to create a 'one stop place' for all
things ibm,associativity.
This patch introduces numa_assoc_array, a 2 dimensional array
that will store all ibm,associativity arrays of all NUMA nodes.
This array is initialized in a new spapr_numa_associativity_init()
function, called in spapr_machine_init(). It is being initialized
with the same values used in other ibm,associativity properties
around spapr files (i.e. all zeros, last value is node_id).
The idea is to remove all hardcoded definitions and FDT writes
of ibm,associativity arrays, doing instead a call to the new
helper spapr_numa_write_associativity_dt() helper, that will
be able to write the DT with the correct values.
We'll start small, handling the trivial cases first. The
remaining instances of ibm,associativity will be handled
next.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200903220639.563090-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This function is only used inside spapr_nvdimm.c.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200901125645.118026-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We're going to make changes in how spapr handles all
ibm,associativity* related properties to enhance our current NUMA
support.
At this moment we have associativity code scattered all around
spapr_* files, with hardcoded values and array sizes. This
makes it harder to change any NUMA specific parameters in
the future. Having everything in the same place allows not
only for easier tuning, but also easier understanding since all
NUMA related code is on the same file.
This patch introduces a new file to gather all NUMA/associativity
handling code in spapr, spapr_numa.c. To get things started, let's
remove associativity-reference-points and max-associativity-domains
code from spapr_dt_rtas() to a new helper called spapr_numa_write_rtas_dt().
This will decouple spapr_dt_rtas() from the NUMA changes that
are going to happen in those two properties.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200901125645.118026-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There are other platforms which also have CPUs that start powered off, so
generalize the start-powered-off property so that it can be used by them.
Note that ARMv7MState also has a property of the same name but this patch
doesn't change it because that class isn't a subclass of CPUState so it
wouldn't be a trivial change.
This change should not cause any change in behavior.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Message-Id: <20200826055535.951207-2-bauerman@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
NVDIMM has different contraints and conditions than the regular
DIMM and we'll need to add at least one more.
Instead of relying on 'if (nvdimm)' conditionals in the body of
spapr_memory_pre_plug(), use the existing spapr_nvdimm_validate_opts()
and put all NVDIMM handling code there. Rename it to
spapr_nvdimm_validate() to reflect that the function is now checking
more than the nvdimm device options. This makes spapr_memory_pre_plug()
a bit easier to follow, and we can tune in NVDIMM parameters
and validation in the same place.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200825215749.213536-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OPAL test suite runs a read-erase-write test on the PNOR :
https://github.com/open-power/op-test/blob/master/testcases/OpTestPNOR.py
which revealed that the IPMI HIOMAP handlers didn't support
HIOMAP_C_ERASE. Implement the sector erase command by writing 0xFF in
the PNOR memory region.
Cc: Corey Minyard <cminyard@mvista.com>
Reported-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200820164638.2515681-1-clg@kaod.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On POWER9, the KVM XIVE device uses priority 7 for the escalation
interrupts. On POWER10, the host can use a reduced set of priorities
and KVM will configure the escalation priority to a lower number. In
any case, the guest is allowed to use priorities in a single range :
[ 0 .. (maxprio - 1) ].
Introduce a 'hv-prio' property to represent the escalation priority
number and use it to compute the "ibm,plat-res-int-priorities"
property defining the priority ranges reserved by the hypervisor.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200819130843.2230799-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_drc.h includes typechecker macro boilerplate for the many different
DRC subclasses. However, most of these types don't actually have different
data in their class and/or instance, making these unneeded, unused, and in
fact a bad idea. Remove them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
* Two build system fixes to fix some failures the CI
* One m68k QOMification patch
* Some trivial qtest patches
* Some small improvements for the Gitlab CI
-----BEGIN PGP SIGNATURE-----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=kPTJ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-09-03' into staging
* Cirrus-CI improvements and fixes (compile with -Werror & fix for 1h problem)
* Two build system fixes to fix some failures the CI
* One m68k QOMification patch
* Some trivial qtest patches
* Some small improvements for the Gitlab CI
# gpg: Signature made Thu 03 Sep 2020 12:04:32 BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-09-03:
gitlab-ci.yml: Set artifacts expiration time
gitlab-ci.yml: Run check-qtest and check-unit at the end of the fuzzer job
gitlab/travis: Rework the disabled features tests
libqtest: Rename qmp_assert_error_class() to qmp_expect_error_and_unref()
tests/qtest/ipmi-kcs: Fix assert side-effect
tests/qtest/tpm: Declare input buffers const and static
tests/qtest/ahci: Improve error handling (NEGATIVE_RETURNS)
hw/m68k: QOMify the mcf5206 system integration module
configure: Add system = 'linux' for meson when cross-compiling
meson: fix keymaps without qemu-keymap
cirrus.yml: Split FreeBSD job into two parts
cirrus.yml: Update the macOS jobs to Catalina
cirrus.yml: Compile macOS with -Werror
cirrus.yml: Compile FreeBSD with -Werror
configure: Fix atomic64 test for --enable-werror on macOS
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
-----BEGIN PGP SIGNATURE-----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=ZQHA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200901' into staging
Various fixes of Aspeed machines :
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
# gpg: Signature made Tue 01 Sep 2020 13:39:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200901:
hw: add a number of SPI-flash's of m25p80 family
arm: aspeed: add strap define `25HZ` of AST2500
aspeed/smc: Open AHB window of the second chip of the AST2600 FMC controller
aspeed/sdmc: Simplify calculation of RAM bits
aspeed/sdmc: Allow writes to unprotected registers
aspeed/sdmc: Perform memory training
ftgmac100: Improve software reset
ftgmac100: Fix integer overflow in ftgmac100_do_tx()
ftgmac100: Check for invalid len and address before doing a DMA transfer
ftgmac100: Change interrupt status when a DMA error occurs
ftgmac100: Fix interrupt status "Packet moved to RX FIFO"
ftgmac100: Fix interrupt status "Packet transmitted on ethernet"
ftgmac100: Fix registers that can be read
aspeed/sdhci: Fix reset sequence
aspeed/smc: Fix max_slaves of the legacy SMC device
aspeed/smc: Fix MemoryRegionOps definition
hw/arm/aspeed: Add board model for Supermicro X11 BMC
aspeed/scu: Fix valid access size on AST2400
m25p80: Add support for n25q512ax3
m25p80: Return the JEDEC ID twice for mx25l25635e
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The mcf5206 system integration module should be a proper device.
Let's finally QOMify it.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200819065201.4045-1-huth@tuxfamily.org>
This reverts commit c24a41bb53.
Remove the EPYC specific apicid decoding and use the generic
default decoding.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <159889937478.21294.4192291354416942986.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This reverts commit 7568b20555.
Remove the EPYC specific apicid decoding and use the generic
default decoding.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <159889936871.21294.1454526726636639780.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This reverts commit 6121c7fbfd.
Remove the EPYC specific apicid decoding and use the generic
default decoding.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <159889935648.21294.8095493980805969544.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the macro to be consistent with RDMA_PROVIDER and
RDMA_PROVIDER_GET_CLASS.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-48-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some QOM macros were using a X86_IOMMU_DEVICE prefix, and others
were using a X86_IOMMU prefix. Rename all of them to use the
same X86_IOMMU_DEVICE prefix.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-47-ehabkost@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the MOS6522_DEVICE_CLASS and MOS6522_DEVICE_GET_CLASS
macros to be consistent with the TYPE_MOS6522 and MOS6522 macros.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-46-ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to IMX_CCM_GET_CLASS to be consistent with the existing
IMX_CCM and IXM_CCM_CLASS macro.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20200825192110.3528606-45-ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Provide a definition for the "25Hz reference clock input mode" strap
Signed-off-by: Igor Kononenko <i.kononenko@yadro.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200811203502.20382-1-i.kononenko@yadro.com>
Message-Id: <20200819100956.2216690-21-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This allows qemu to run the "normal" power on reset boot path through
u-boot, where the DDR is trained.
An enhancement would be to have the SCU bit stick across qemu reboots,
but be unset on initial boot.
Proper modelling would be to discard all writes to the phy setting regs
at offset 0x100 - 0x400 and to model the phy status regs at offset
0x400.
The status regs model would only need to account for offets 0x00,
0x50, 0x68 and 0x7c.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: checkpatch fixes ]
Message-Id: <20200819100956.2216690-17-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Group some HID values that are used pretty much everywhere when
dealing with HID devices.
Signed-off-by: César Belley <cesar.belley@lse.epita.fr>
Message-id: 20200812094135.20550-2-cesar.belley@lse.epita.fr
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
TYPE_ARM_SSE is a TYPE_SYS_BUS_DEVICE subclass, but
ARMSSEClass::parent_class is declared as DeviceClass.
It never caused any problems by pure luck:
We were not setting class_size for TYPE_ARM_SSE, so class_size of
TYPE_SYS_BUS_DEVICE was being used (sizeof(SysBusDeviceClass)).
This made the system allocate enough memory for TYPE_ARM_SSE
devices even though ARMSSEClass was too small for a sysbus
device.
Additionally, the ARMSSEClass::info field ended up at the same
offset as SysBusDeviceClass::explicit_ofw_unit_address. This
would make sysbus_get_fw_dev_path() crash for the device.
Luckily, sysbus_get_fw_dev_path() never gets called for
TYPE_ARM_SSE devices, because qdev_get_fw_dev_path() is only used
by the boot device code, and TYPE_ARM_SSE devices don't appear at
the fw_boot_order list.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 20200826181006.4097163-1-ehabkost@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To have a better idea of how big is the region where the offset
belongs, display the value with the width of the region size
(i.e. a region of 0x1000 bytes uses 0x000 format).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200812190206.31595-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clock canonical name is set in device_set_realized (see the block
added to hw/core/qdev.c in commit 0e6934f264).
If we connect a clock after the device is realized, this code is
not executed. This is currently not a problem as this name is only
used for trace events, however this disrupt tracing.
Add a comment to document qdev_connect_clock_in() must be called
before the device is realized, and assert this condition.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to assert the device is not realized. To avoid overloading
this header including "hw/qdev-core.h", uninline the function first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we want to call qdev_connect_clock_in() before the device
is realized, we need to uninline cadence_uart_create() first.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200803105647.22223-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The H3 SoC keeps using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814122907.27732-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the device to execute the DMA transfers in a different
AddressSpace.
The A10 and H3 SoC keep using the system_memory address space,
but via the proper dma_memory_access() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200814110057.307-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Avoid propagating the clock change when the clock does not change.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let clock_set() return a boolean value whether the clock
has been updated or not.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
clock_init*() inlined funtions are simple wrappers around
clock_set*() and are not used. Remove them in favor of clock_set*().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200806123858.30058-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we have a SWIM typedef and a SWIM type checking macro,
but OBJECT_DECLARE* would transform the SWIM macro into a
function, and the function name would conflict with the SWIM
typedef name.
Rename the struct and typedef to "Swim". This will make future
conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-50-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to be consistent with S390_CCW_MACHINE and
TYPE_S390_CCW_MACHINE.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-49-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the existing class type checking macros to be consistent
with the type name and instance type checking macro. Use a
NUBUS_MACFB prefix instead of MACFB_NUBUS.
This will make future conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-44-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-38-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-37-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-36-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move all declarations related to TYPE_VMBUS to the same place in
vmbus.h.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-35-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the I8042 macro close to the TYPE_I8042 define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-34-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the ALLWINNER_AHCI macro close to the TYPE_ALLWINNER_AHCI
define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-33-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the I8257 macro to i8257.h, close to the TYPE_I8257 define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-32-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The TYPE_* constants and the typedefs are defined in ahci.h, so
we can move the type checking macros there too.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the VHOST_USER_GPU type checking macro to virtio-gpu.h,
close to the TYPE_VHOST_USER_GPU #define.
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-30-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
In sclp.h, use "struct SCLPEventFacility" to avoid introducing
unnecessary header dependencies.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-29-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the typedef from spapr_irq.h to spapr.h, and use "struct
SpaprMachineState" in the spapr_*.h headers (to avoid circular
header dependencies).
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-28-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The typedef was used in the XENBACKEND_DEVICE macro, but it was
never defined. Define the typedef close to the type checking
macro.
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-27-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename TYPE_ARMSSE to TYPE_ARM_SSE, and ARMSSE*() type checking
macros to ARM_SSE*().
This will avoid a future conflict between an ARM_SSE() type
checking macro and the ARMSSE typedef name.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-26-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
PlatformBusDeviceClass doesn't exist. This will break when we
automatically convert the code to use OBJECT_DEFINE_TYPE().
Delete the macros that reference the non-existing typedef.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-25-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro never worked because the NubusBridge typedef doesn't
exist. Delete it.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-22-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-21-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-19-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
