This adds IPv6 net boot testing (in addition to IPv4) when in slow test
mode on ppc64 or s390. IPv6 PXE doesn't seem to work on x86, I'm guessing
our BIOS image doesn't support it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently pxe-tests open codes the list of tests for each architecture.
This changes it to use tables of test parameters, somewhat similar to
boot-serial-test.
This adds the machine type into the table as well, giving us the ability
to perform tests on multiple machine types for architectures where there's
more than one machine type that matters.
NOTE: This changes the names of the tests in the output, to include the
machine type and IPv4 vs. IPv6. I'm not sure if this has the
potential to break existing tooling.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All of the x86 and some of the other test cases here use a common test
function, test_pxe_ipv4(), but one ppc and one s390 test use different
functions.
In the s390 case, this is completely pointless, the right parameter to
test_pxe_ipv4() will already do exactly the right thing. For the
spapr-vlan case there's a slight difference - it will use IPv6 instead of
IPv4.
But testing just one case with IPv6 (and NOT IPv4) is rather haphazard.
Change everything to use the common test function, until we have a better
way of testing IPv6 across the board.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Backends don't need to know what frontend requested a reset,
and notifying then from virtio_error is messy because
virtio_error itself might be invoked from backend.
Let's just set the status directly.
Cc: qemu-stable@nongnu.org
Reported-by: Ilya Maximets <i.maximets@samsung.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_find_primary_bus() only has one user, in pc_xen_hvm_init(). That's
inside the machine construction code, so it already has easy access to the
machine's primary PCI bus.
Get it directly, and thereby remove pci_find_primary_bus(). This removes
one of only a handful of users of the ugly pci_host_bridges global.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
The bus pointer in PCIDevice is basically redundant with QOM information.
It's always initialized to the qdev_get_parent_bus(), the only difference
is the type.
Therefore this patch eliminates the field, instead creating a pci_get_bus()
helper to do the type mangling to derive it conveniently from the QOM
Device object underneath.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
A fair proportion of the users of pci_bus_num() want to get the bus
number on a specific device, so first have to look up the bus from the
device then call it. This adds a helper to do that (since we're going
to make looking up the bus slightly more verbose).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
include/hw/pci/pci_bus.h contains several data structures related to PCI
bridges that aren't needed by most users of pci_bus.h. We already have
a pci_bridge.h, so move them there.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
pci_bus_init(), pci_bus_new_inplace(), pci_bus_new() and pci_register_bus()
are misleadingly named. They're not used for initializing *any* PCI bus,
but only for a root PCI bus.
Non-root buses - i.e. ones under a logical PCI to PCI bridge - are instead
created with a direct qbus_create_inplace() (see pci_bridge_initfn()).
This patch renames the functions to make it clear they're only used for
a root bus.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
An uninitialised VirtQueue object or one with Vring.align field
set to zero(0) could lead to arithmetic exceptions. Add a unit
test to validate it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Switch vmgenid device to use the UUID property type introduced in the
previous patch for its 'guid' property.
One semantic change it introduces is that post-realize modification of
'guid' via HMP or QMP will now be rejected with an error; however,
according to docs/specs/vmgenid.txt this is actually desirable.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Ben Warren <ben@skyportsystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
UUIDs (GUIDs) are widely used in VMBus-related stuff, so a dedicated
property type becomes helpful.
The property accepts a string-formatted UUID or a special keyword "auto"
meaning a randomly generated UUID; the latter is also the default when
the property is not given a value explicitly.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The cloud-init program currently allows fetching of its data by repurposing of
the 'system' type 'serial' field. This is a clear abuse of the serial field that
would clash with other valid usage a virt management app might have for that
field.
Fortunately the SMBIOS defines an "OEM Strings" table whose puporse is to allow
exposing of arbitrary vendor specific strings to the operating system. This is
perfect for use with cloud-init, or as a way to pass arguments to OS installers
such as anaconda.
This patch makes it easier to support this with QEMU. e.g.
$QEMU -smbios type=11,value=Hello,value=World,value=Tricky,,value=test
Which results in the guest seeing dmidecode data
Handle 0x0E00, DMI type 11, 5 bytes
OEM Strings
String 1: Hello
String 2: World
String 3: Tricky,value=test
It is suggested that any app wanting to make use of this OEM strings capability
for accepting data from the host mgmt layer should use its name as a string
prefix. e.g. to expose OEM strings targetting both cloud init and anaconda in
parallel the mgmt app could set
$QEMU -smbios type=11,value=cloud-init:ds=nocloud-net;s=http://10.10.0.1:8000/,\
value=anaconda:method=http://dl.fedoraproject.org/pub/fedora/linux/releases/25/x86_64/os
which would appear as
Handle 0x0E00, DMI type 11, 5 bytes
OEM Strings
String 1: cloud-init:ds=nocloud-net;s=http://10.10.0.1:8000/
String 2: anaconda:method=http://dl.fedoraproject.org/pub/fedora/linux/releases/25/x86_64/os
Use of such string prefixes means the app won't have to care which string slot
its data appears in.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 5c0919d020 ("virtio-scsi: Add virtqueue_size parameter allowing
virtqueue size to be set.") introduced a new parameter to virtio-scsi.
Later, commit 9200361060 ("vhost-user-scsi: add missing virtqueue_size
param") added that parameter to the new vhost-user-scsi interface but
neglected the existing vhost-scsi interface it was built on.
Apply the same change to vhost-scsi, so that we can boot a guest with
a device defined. This also avoids crashing a guest when hotplugging
a vhost-scsi device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-id: 20171201151538.6844-2-farman@linux.vnet.ibm.com
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Alas, this is yet another fix for ppc that I think it's worth
squeezing into 2.11. It's a really ugly fix for some pretty ugly
code, but it does seem to address a real problem. It's also a problem
that's appeared relatively recently, since it was either created by,
or made much easier to trigger by, by the merge of MTTCG.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEdfRlhq5hpmzETofcbDjKyiDZs5IFAlomLXQACgkQbDjKyiDZ
s5IHeg//X3JQ//s7BhmAAPERA4p/0bwuRZWk1T+zwypc1HZegjDfwMtH0GCjhabU
OhVgdneuqFwHJEeWyLWLpEwHazX8hk9CYRYi186oblHgKtPaqXRI30Pnywni3hx6
Bx4GFf84fZmPdibbE3IGNpyXOjUuAsx54MaWKpIZzYTTrZYUc2+W8DK7B9kiiAfm
Tv1mWJxg7YVtnedB8wo+HyEjGL3V3Ww+09YmYqjJz+AQT05fFONYJddLjvnFInFs
FtSqeF8KD86KbhPSWVJtSGwHMXO344F2ZhIjk57JwKDxDC/x/0Xg/7pmQ0RMSvxW
phTHsQ0iCoJs0ix6B0ATlqxgMlVf5GkveqIkgxF8z9QrAjajHSHasVsBRbb+qaRS
ozWdtYPHiN/+hjg8zEsmUR3yPtyHysk5KDWCq7rAt7thFEV6xTMfIDNAKDlwmE5i
JhoTHLj+wH+l6q3/iuzQpSLTfymN2fA2f58IK+U1WUo0fHEg4bRW/dHz+SO6gJwV
iTyl0Du2T5eaKGvfdB9jfGQXrmXcOu1yNLTD4pUG3cpGI57dPnoL+/Qq/gIQgmwl
qBTCSlJWWoiwy0v7iEixd5ULDAG5l8niUyGNPTsN8PXtwProyfSvY/eHwEcrmwWo
0lt+sJUywKEeL+TVnRdny4fFSOcb861m3GEYfAj/uSlYKLDjnaE=
=L4ZT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20171205' into staging
ppc patch queue 2017-12-05
Alas, this is yet another fix for ppc that I think it's worth
squeezing into 2.11. It's a really ugly fix for some pretty ugly
code, but it does seem to address a real problem. It's also a problem
that's appeared relatively recently, since it was either created by,
or made much easier to trigger by, by the merge of MTTCG.
# gpg: Signature made Tue 05 Dec 2017 05:24:04 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20171205:
target/ppc: Fix system lockups caused by interrupt_request state corruption
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Occasionally in Linux guests on x86_64 we're seeing logs like:
ppc_set_irq: 0x55b4e0d562f0 n_IRQ 8 level 1 => pending 00000100req 00000004
when they should read:
ppc_set_irq: 0x55b4e0d562f0 n_IRQ 8 level 1 => pending 00000100req 00000002
The "00000004" is CPU_INTERRUPT_EXITTB yet the code calls
cpu_interrupt(cs, CPU_INTERRUPT_HARD) ("00000002") in this function
just before the log message. Something is causing the HARD bit setting
to get lost.
The knock on effect of losing that bit is the decrementer timer interrupts
don't get delivered which causes the guest to sit idle in its idle handler
and 'hang'.
The issue occurs due to races from code which sets CPU_INTERRUPT_EXITTB.
Rather than poking directly into cs->interrupt_request, that code needs to:
a) hold BQL
b) use the cpu_interrupt() helper
This patch fixes the call sites to do this, fixing the hang. The calls
are made from a variety of contexts so a helper function is added to handle
the necessary locking. This can likely be improved and optimised in the future
but it ensures the code is correct and doesn't lockup as it stands today.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Starting from commit 40840e419b we are
pausing all block jobs during bdrv_reopen_multiple() to prevent any of
them from finishing and removing nodes from the graph while they are
being reopened.
It turns out that pausing a block job doesn't necessarily prevent it
from finishing: a paused block job can still run its exit function
from the main loop and call block_job_completed(). The mirror block
job in particular always goes to the main loop while it is paused (by
virtue of the bdrv_drained_begin() call in mirror_run()).
Destroying a paused block job during bdrv_reopen_multiple() has two
consequences:
1) The references to the nodes involved in the job are released,
possibly destroying some of them. If those nodes were in the
reopen queue this would trigger the problem originally described
in commit 40840e419b, crashing QEMU.
2) At the end of bdrv_reopen_multiple(), bdrv_drain_all_end() would
not be doing all necessary bdrv_parent_drained_end() calls.
I can reproduce problem 1) easily with iotest 030 by increasing
STREAM_BUFFER_SIZE from 512KB to 8MB in block/stream.c, or by tweaking
the iotest like in this example:
https://lists.gnu.org/archive/html/qemu-block/2017-11/msg00934.html
This patch keeps an additional reference to all block jobs between
block_job_pause_all() and block_job_resume_all(), guaranteeing that
they are kept alive.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaIYwZAAoJECgfDbjSjVRpeL0IAKSrsoe8c5WSwRWerRdlDE14
EUjUtz3sEhTNC05fTX/t7OyBnuRaU3T3und0ZwArCR4gIE196yzj619ZOReYeoJp
iPqqVTR6gPP7Y0IeeI56wV9wSyOH68n9JM4MOWdXjquSrJxrGg+fPxWXQH/pvmfy
QEhFkg/kL48c1ezJUIIAFdU0I+NY4dSzuAjINgl2rdlEATIMQBsEnOlFSgwg1aTb
pAPz/uOvVdstnnW2JiA0n0slU2Ix2eorHuv3B0J4wRb2mTD/uQWml0eaWYQf6cLu
O3dgifkhuxwmm7kUedZGYtUSj9cHGLnH850ovo6mW1/Drte2SItCqrlsh230cW8=
=ZiXl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: fixes for rc3
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Dec 2017 17:06:33 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
pc: fix crash on attempted cpu unplug
virtio: check VirtQueue Vring object is set
vhost: fix error check in vhost_verify_ring_mappings()
dump-guest-memory.py: fix No symbol "vmcoreinfo_find"
vhost: restore avail index from vring used index on disconnection
virtio: Add queue interface to restore avail index from vring used index
i386/msi: Correct mask of destination ID in MSI address
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We are, alas, not yet to the bottom of ppc bugs. This pull request
fixes several more. I believe they're important enough to include in
2.11. despite the late date.
-----BEGIN PGP SIGNATURE-----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=fgoQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.11-20171204' into staging
ppc patch queue 2017-12-04
We are, alas, not yet to the bottom of ppc bugs. This pull request
fixes several more. I believe they're important enough to include in
2.11. despite the late date.
# gpg: Signature made Mon 04 Dec 2017 03:40:56 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20171204:
spapr: Include "pre-plugged" DIMMS in ram size calculation at reset
target-ppc: Don't invalidate non-supported msr bits
pseries: fix TCG migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At guest reset time, we allocate a hash page table (HPT) for the guest
based on the guest's RAM size. If dynamic HPT resizing is not available we
use the maximum RAM size, if it is we use the current RAM size.
But the "current RAM size" calculation is incorrect - we just use the
"base" ram_size from the machine structure. This doesn't include any
pluggable DIMMs that are already plugged at reset time.
This means that if you try to start a 'pseries' machine with a DIMM
specified on the command line that's much larger than the "base" RAM size,
then the guest will get a woefully inadequate HPT. This can lead to a
guest freeze during boot as it runs out of HPT space during initial MMU
setup.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
when qemu is started with '-no-acpi' CLI option, an attempt
to unplug a CPU using device_del results in null pointer
dereference at:
#0 object_get_class
#1 pc_machine_device_unplug_request_cb
#2 qmp_marshal_device_del
which is caused by pcms->acpi_dev == NULL due to ACPI support
being disabled.
Considering that ACPI support is necessary for unplug to work,
check that it's enabled and fail unplug request gracefully
if no acpi device were found.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A guest could attempt to use an uninitialised VirtQueue object
or unset Vring.align leading to a arithmetic exception. Add check
to avoid it.
Reported-by: Zhangboxian <zhangboxian@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Since commit f1f9e6c5 "vhost: adapt vhost_verify_ring_mappings() to
virtio 1 ring layout", we check the mapping of each part (descriptor
table, available ring and used ring) of each virtqueue separately.
The checking of a part is done by the vhost_verify_ring_part_mapping()
function: it returns either 0 on success or a negative errno if the
part cannot be mapped at the same place.
Unfortunately, the vhost_verify_ring_mappings() function checks its
return value the other way round. It means that we either:
- only verify the descriptor table of the first virtqueue, and if it
is valid we ignore all the other mappings
- or ignore all broken mappings until we reach a valid one
ie, we only raise an error if all mappings are broken, and we consider
all mappings are valid otherwise (false success), which is obviously
wrong.
This patch ensures that vhost_verify_ring_mappings() only returns
success if ALL mappings are okay.
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When qemu is compiled without debug, the dump gdb python script can fail with:
Error occurred in Python command: No symbol "vmcoreinfo_find" in current context.
Because vmcoreinfo_find() is inlined and not exported.
Use the underlying object_resolve_path_type() to get the instance instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost_virtqueue_stop() gets avail index value from the backend,
except if the backend is not responding.
It happens when the backend crashes, and in this case, internal
state of the virtio queue is inconsistent, making packets
to corrupt the vring state.
With a Linux guest, it results in following error message on
backend reconnection:
[ 22.444905] virtio_net virtio0: output.0:id 0 is not a head!
[ 22.446746] net enp0s3: Unexpected TXQ (0) queue failure: -5
[ 22.476360] net enp0s3: Unexpected TXQ (0) queue failure: -5
Fixes: 283e2c2adc ("net: virtio-net discards TX data after link down")
Cc: qemu-stable@nongnu.org
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In case of backend crash, it is not possible to restore internal
avail index from the backend value as vhost_get_vring_base
callback fails.
This patch provides a new interface to restore internal avail index
from the vring used index, as done by some vhost-user backend on
reconnection.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to SDM 10.11.1, only [19:12] bits of MSI address are
Destination ID, change the mask to avoid ambiguity for VT-d spec
has used the bit 4 to indicate a remappable interrupt request.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The msr invalidation code (commits 993eb and 2360b) inverts all
bits except MSR_TGPR and MSR_HVB. On non PowerPC 601 processors
this leads to incorrect change of excp_prefix in hreg_store_msr()
function. The problem is that new msr value get multiplied by msr_mask
and inverted msr does not, thus values of MSR_EP bit in new msr value
and inverted msr are distinct, so that excp_prefix changes but should
not.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Migration of pseries is broken with TCG because
QEMU tries to restore KVM MMU state unconditionally.
The result is a SIGSEGV in kvm_vm_ioctl():
#0 kvm_vm_ioctl (s=0x0, type=-2146390353)
at qemu/accel/kvm/kvm-all.c:2032
#1 0x00000001003e3e2c in kvmppc_configure_v3_mmu (cpu=<optimized out>,
radix=<optimized out>, gtse=<optimized out>, proc_tbl=<optimized out>)
at qemu/target/ppc/kvm.c:396
#2 0x00000001002f8b88 in spapr_post_load (opaque=0x1019103c0,
version_id=<optimized out>) at qemu/hw/ppc/spapr.c:1578
#3 0x000000010059e4cc in vmstate_load_state (f=0x106230000,
vmsd=0x1009479e0 <vmstate_spapr>, opaque=0x1019103c0,
version_id=<optimized out>) at qemu/migration/vmstate.c:165
#4 0x00000001005987e0 in vmstate_load (f=<optimized out>, se=<optimized out>)
at qemu/migration/savevm.c:748
This patch fixes the problem by not calling the KVM function with the
TCG mode.
Fixes: d39c90f5f3 ("spapr: Fix migration of Radix guests")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
DIV_ROUND_UP(st.st_size, BDRV_SECTOR_SIZE) was overflowing ret (int) if
st.st_size is greater than 1TB.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1511798407-31129-1-git-send-email-pl@kamp.de
Signed-off-by: Max Reitz <mreitz@redhat.com>
This reverts the effects of commit 4afeffc857 ("blockjob: do not allow
coroutine double entry or entry-after-completion", 2017-11-21)
This fixed the symptom of a bug rather than the root cause. Canceling the
wait on a sleeping blockjob coroutine is generally fine, we just need to
make it work correctly across AioContexts. To do so, use a QEMUTimer
that calls block_job_enter. Use a mutex to ensure that block_job_enter
synchronizes correctly with block_job_sleep_ns.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-By: Jeff Cody <jcody@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Hide the clearing of job->busy in a single function, and set it
in block_job_enter. This lets block_job_do_yield verify that
qemu_coroutine_enter is not used while job->busy = false.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-By: Jeff Cody <jcody@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All callers are using QEMU_CLOCK_REALTIME, and it will not be possible to
support more than one clock when block_job_sleep_ns switches to a single
timer stored in the BlockJob struct.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Tested-By: Jeff Cody <jcody@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The .drained_begin/end callbacks can (directly or indirectly via
aio_poll()) cause block nodes to be removed or the current BdrvChild to
point to a different child node.
Use QLIST_FOREACH_SAFE() to make sure we don't access invalid
BlockDriverStates or accidentally continue iterating the parents of the
new child node instead of the node we actually came from.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When destroying a block job in block_job_unref() we should remove it
from the job list before calling block_job_remove_all_bdrv().
This is because removing the BDSs can trigger an aio_poll() and wake
up other jobs that might attempt to use the block job list. If that
happens the job we're currently destroying should not be in that list
anymore.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Introduced in commit f37708f6b8 (2.10). The NBD spec says a client
can request export names up to 4096 bytes in length, even though
they should not expect success on names longer than 256. However,
qemu hard-codes the limit of 256, and fails to filter out a client
that probes for a longer name; the result is a stack smash that can
potentially give an attacker arbitrary control over the qemu
process.
The smash can be easily demonstrated with this client:
$ qemu-io f raw nbd://localhost:10809/$(printf %3000d 1 | tr ' ' a)
If the qemu NBD server binary (whether the standalone qemu-nbd, or
the builtin server of QMP nbd-server-start) was compiled with
-fstack-protector-strong, the ability to exploit the stack smash
into arbitrary execution is a lot more difficult (but still
theoretically possible to a determined attacker, perhaps in
combination with other CVEs). Still, crashing a running qemu (and
losing the VM) is bad enough, even if the attacker did not obtain
full execution control.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
The NBD spec gives us permission to abruptly disconnect on clients
that send outrageously large option requests, rather than having
to spend the time reading to the end of the option. No real
option request requires that much data anyways; and meanwhile, we
already have the practice of abruptly dropping the connection on
any client that sends NBD_CMD_WRITE with a payload larger than 32M.
For comparison, nbdkit drops the connection on any request with
more than 4096 bytes; however, that limit is probably too low
(as the NBD spec states an export name can theoretically be up
to 4096 bytes, which means a valid NBD_OPT_INFO could be even
longer) - even if qemu doesn't permit exports longer than 256
bytes.
It could be argued that a malicious client trying to get us to
read nearly 4G of data on a bad request is a form of denial of
service. In particular, if the server requires TLS, but a client
that does not know the TLS credentials sends any option (other
than NBD_OPT_STARTTLS or NBD_OPT_EXPORT_NAME) with a stated
payload of nearly 4G, then the server was keeping the connection
alive trying to read all the payload, tying up resources that it
would rather be spending on a client that can get past the TLS
handshake. Hence, this warranted a CVE.
Present since at least 2.5 when handling known options, and made
worse in 2.6 when fixing support for NBD_FLAG_C_FIXED_NEWSTYLE
to handle unknown options.
CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
If socket_listen_cleanup is passed an invalid FD, then querying the socket
local address will fail. We must thus be prepared for the returned addr to
be NULL
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJaHN7TAAoJEO8Ells5jWIRkYYH/jUDWH5/LXVnA+2R8/k8/jQL
wyXvVKdAJloU1MZ1N49dpPifkQjLcRZ2CD0o+5W91z1WSOj4966/+C9+nNsogJpn
08hq01zdnquNQf/4z1Gl2hoIYQe/z1AaDCNuI1py/vUDh4+VwkxXBtf8DSeBveja
1+qdg+NCWWrwp9f5cygR9F4tOI+HfYjqI6nqIBsITXeQ3zPUbs+1Ry1YRJ+kUKqI
xixxKm2M2sYKHtEFTtHQpvEMbKxuuEaGGZ6uHgm6t7HIcGE1YOn1NIPa4AvTfeFO
2tKcynR0c3Svhq07b3M/JrnPhjQgOfOUwzaLB5sHNThkjV65jS0/23M5cTvo5tI=
=mazL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Tue 28 Nov 2017 03:58:11 GMT
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
virtio-net: don't touch virtqueue if vm is stopped
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Guest state should not be touched if VM is stopped, unfortunately we
didn't check running state and tried to drain tx queue unconditionally
in virtio_net_set_status(). A crash was then noticed as a migration
destination when user type quit after virtqueue state is loaded but
before region cache is initialized. In this case,
virtio_net_drop_tx_queue_data() tries to access the uninitialized
region cache.
Fix this by only dropping tx queue data when vm is running.
Fixes: 283e2c2adc ("net: virtio-net discards TX data after link down")
Cc: Yuri Benditovich <yuri.benditovich@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When you cancel an in-progress 'mirror' job (or "active `block-commit`")
with QMP `block-job-cancel`, it emits the event: BLOCK_JOB_CANCELLED.
However, when `block-job-cancel` is issued *after* `drive-mirror` has
indicated (via the event BLOCK_JOB_READY) that the source and
destination have reached synchronization:
[...] # Snip `drive-mirror` invocation & outputs
{
"execute":"block-job-cancel",
"arguments":{
"device":"virtio0"
}
}
{"return": {}}
It (`block-job-cancel`) will counterintuitively emit the event
'BLOCK_JOB_COMPLETED':
{
"timestamp":{
"seconds":1510678024,
"microseconds":526240
},
"event":"BLOCK_JOB_COMPLETED",
"data":{
"device":"virtio0",
"len":41126400,
"offset":41126400,
"speed":0,
"type":"mirror"
}
}
But this is expected behaviour, where the _COMPLETED event indicates
that synchronization has successfully ended (and the destination now has
a point-in-time copy, which is at the time of cancel).
So add a small note to this effect in 'block-core.json'. While at it,
also update the "Live disk synchronization -- drive-mirror and
blockdev-mirror" section in 'live-block-operations.rst'.
(Thanks: Max Reitz for reminding me of this caveat on IRC.)
Signed-off-by: Kashyap Chamarthy <kchamart@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
