This patch adds a new type for the binary representation of usb
descriptors. It is put into use for the descriptor generator code
where the struct replaces the hard-coded offsets.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
frindex always is a 14 bits counter, and not a 13 bits one as we were
emulating. There are some subtle hints to this in the spec, first of all
"Table 2-12. FRINDEX - Frame Index Register" says:
"Bit 13:0 Frame Index. The value in this register increments at the end of
each time frame (e.g. micro-frame). Bits [N:3] are used for the Frame List
current index. This means that each location of the frame list is accessed
8 times (frames or micro-frames) before moving to the next index. The
following illustrates values of N based on the value of the Frame List
Size field in the USBCMD register.
USBCMD[Frame List Size] Number Elements N
00b 1024 12
01b 512 11
10b 256 10
11b Reserved"
Notice how the text talks about "Bits [N:3]" are used ..., it does
NOT say that when N == 12 (our case) the counter will wrap from 8191 to 0,
or in otherwords that it is a 13 bits counter (bits 0 - 12).
The other hint is in "Table 2-10. USBSTS USB Status Register Bit Definitions":
"Bit 3 Frame List Rollover - R/WC. The Host Controller sets this bit to a one
when the Frame List Index (see Section 2.3.4) rolls over from its maximum value
to zero. The exact value at which the rollover occurs depends on the frame
list size. For example, if the frame list size (as programmed in the Frame
List Size field of the USBCMD register) is 1024, the Frame Index Register
rolls over every time FRINDEX[13] toggles. Similarly, if the size is 512,
the Host Controller sets this bit to a one every time FRINDEX[12] toggles."
Notice how this text talks about setting bit 3 when bit 13 of frindex toggles
(when there are 1024 entries, so our case), so this indicates that frindex
has a bit 13 making it a 14 bit counter.
Besides these clear hints the real proof is in the pudding. Before this
patch I could not stream data from a USB2 webcam under Windows XP, after
this cam using a USB2 webcam under Windows XP works fine, and no regressions
with other operating systems were seen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Looks like a cut+paste bug from ehci_detach. When the device itself is
detached from a ehci port (ehci_detach op) we have to clear the
device pointer for the companion port too. When a device gets removed
from a downstream port of a usb hub (ehci_child_detach op) the ehci port
where the usb hub is plugged in is not affected.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_packet_set_state can be called with p->ep = NULL. The tracepoint
there tries to log endpoint information, which leads to a segfault.
This patch makes usb_packet_set_state handle the NULL pointer properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add pointer to USBPacket to all tracepoints tracking requests to make it
easier to identify them when multiple requests are in flight.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When passing through a usb pendrive seabios will present it in the F12
boot menu and will happily boot from it.
This patch adds bootorder support so you can even make it the default
boot device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When we queue up usb packets we may happen to find a already queued
packet, which also might be finished at that point already. We don't
want continue processing the packet at this point though, so lets
just signal back we've found a in-flight packet when in queuing mode.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Not only QHs can form rings, but TDs too. With the new
queuing/pipelining support we are following TD chains and
can actually walk in circles. An assert() prevents us from
entering an endless loop then.
Fix is easy: Just stop queuing when we figure the TD we are
about to queue up is in flight already.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
... to make vmstate id string truely unique with multiple host
controllers, i.e. move from "1/usb-ptr" to "0000:00:01.3/1/usb-ptr"
(usb tabled connected to piix3 uhci).
This obviously breaks migration. To handle this the usb bus
property "full-path" is added. When setting this to false old
behavior is maintained. This way current qemu will be compatible
with old versions when started using '-M pc-$oldversion'.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* kiszka/queues/pending:
vapic: Disable for pre-1.1 machines
Kick io-thread on qemu_chr_accept_input
pcnet: Properly handle TX requests during Link Fail
pcnet: Clear ERR in CSR0 on stop
signrom: Rewrite as python script
Conflicts:
hw/pc_piix.c
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
* sstabellini/for_anthony:
xen: introduce an event channel for buffered io event notifications
xen-mapcache: don't unmap locked entry during mapcache invalidation
Xen, mapcache: Fix the compute of the size of bucket.
xen: handle backend deletion from xenstore
Xen: Add xen-apic support and hook it up.
Xen: basic HVM MSI injection support.
As long as we have no link and we aren't in internal loopback mode, no
packet must be sent. Instead, LCAR needs to be set in any active TX
descriptor and also CERR in CSR0.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
pcnet_stop already clears any reason (BABL, CERR, MISS, MERR) why ERR
(bit 15) should be set in CRS0. So we have to clear that bit as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Currently, the PAPR VIO network device does not have a reset handler. This
means that after a hard reset, H_REGISTER_LOGICAL_LAN will return an error
when the new guest boot attempts to initialize the device.
This patch corrects this, adding a suitable reset hook.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Currently the PAPR vscsi implementation does not properly clear its table
of request tags when the system is reset. This patch adds a reset hook
to do so.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Recently we added code to properly clean away VIO CRQs on reset However,
this directly uses qemu_register, rather than the existing device model
reset callbacks. This patch cleans this up by adding proper use of the
reset hook to the VIO bus model. The existing CRQ reset code is converted
to the new method.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Some time ago we removed all use of the 'hcalls' callback in the pseries
VIO code, which was used to workaround an ordering problem which has since
been solved properly. However, the function pointer for the hook remains.
This patch cleans it away.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The PAPR VSCSI emulation contains a few lines of code which were once used
for debug but now do nothing at all. This patch removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
On the pseries platform, access to PCI config space is via RTAS calls(
which go to the hypervisor) rather than MMIO. This means we don't use
the same code path as nearly everyone else which goes through pci_host.c
and we're missing some of the parameter checking along the way.
We do have some parameter checking in the RTAS calls, but it's not enough.
It checks for overruns, but does not check for unaligned accesses,
oversized accesses (which means the guest could trigger an assertion
failure from pci_host_config_{read,write}_common(). Worse it doesn't do
the basic checking for the number of RTAS arguments and results before
accessing them.
This patch fixes these bugs.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[AF: Fix typos spotted by mst]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Currently the pseries machine contains not one but two somewhat ugly hacks
to allow printing of early debug messages before the guest has properly
read the device tree.
First, we special case H_PUT_TERM_CHAR so that a vtermno of 0 (usually
invalid) will look for a suitable vty and use that. This supports Linux's
early debug code which will use H_PUT_TERM_CHAR with vtermno==0 before
reading the device tree. Second, we support the RTAS display-character call.
This takes no vtermno so we assume the address of the default first VTY.
This patch makes things more consistent by folding the second hack into the
first. Now, display-character uses the existing vty_lookup() function to
do the same search for a suitable VTY.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The VIOsPAPRBus structure, used on the pseries machine contains some old
fields which are no longer used anywhere. This patch removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This patch adds the PAPR defined RTAS system-reboot call to the pseries
machine emulation, providing the guest with a way to trigger a reboot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
PAPR specifies a Command Response Queue (CRQ) mechanism used for virtual
IO, which we implement. However, we don't correctly clean up registered
CRQs when we reset the system.
This patch adds a reset handler to fix this bug. While we're at it, add
in some of the extra debug messages that were used to track the problem
down.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[AF: Updated hcall_dprintf()s to not duplicate the function name]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The pseries machine code has a number of debug messages for debugging PAPR
hypercalls, dependent on DEBUG_SPAPR_HCALLS. This patch cleans these
messages up a bit, by adding __func__ to the hcall_dprintf() macro and
simplifying up a number of the individual messages accordingly.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Commit d0ed8076cb converted the PCI config access to the memory
API, but also inadvertantly changed it to accept unaligned writes,
and corrupt the index register in the process. This causes a regression
booting NetBSD.
Fix by ignoring unaligned or non-dword writes.
https://bugs.launchpad.net/qemu/+bug/897771
Reported-by: Andreas Gustafsson <gson@gson.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Slot present bit is cleared apparently for each device. Hotplug and non
hotplug devices should not mix normally, and we only set the bit when we
add a device so it should all work out, but it's more robust to
explicitly account for more than one device per slot.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCI hotplug eject register has always returned 0, so let's redefine
it as a hotplug feature register. The existing model of using separate
up & down read-only registers and an eject via write to this register
becomes the base implementation. As we make use of new interfaces we'll
set bits here to allow the BIOS and AML implementation to optimize for
the platform implementation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Clarify this register as read-only and remove write code. No
change in existing behavior.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As Michael Tsirkin demonstrated, current PCI hotplug is vulnerable
to a few races. The first is a race with other hotplug operations
because we clear the up & down registers at each event. If a new
event comes before the last is processed, up/down is cleared and
the event is lost.
To fix this for the down register, we create a life cycle for
the event request that starts with the hot unplug request in
piix4_device_hotplug() and ends when the device is ejected.
This allows us to mask and clear individual bits, preserving them
against races. For the up register, we have no clear end point
for when the event is finished. We could modify the BIOS to
acknowledge the bit and clear it, but this creates BIOS compatibiliy
issues without offering a complete solution. Instead we note that
gratuitous ACPI device checks are not harmful, which allows us to
issue a device check for every slot. We know which slots are present
and we know which slots are hotpluggable, so we can easily reduce
this to a more manageable set for the guest.
The other race Michael noted was that an unplug request followed
by reset may also lose the eject notification, which may also
result in the eject request being lost which a subsequent add
or remove. Once we're in reset, the device is unused and we can
flush the queue of device removals ourselves. Previously if a
device_del was issued to a guest without ACPI PCI hotplug support,
it was necessary to shutdown the guest to recover the device.
With this, a guest reboot is sufficient.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The write side of these registers is never used and actually can't be
used as defined because any read/modify/write sequence from the guest
potentially races with qemu. Drop the write support and define these
as read-only registers.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* 'arm-devs.for-upstream' of git://git.linaro.org/people/pmaydell/qemu-arm:
hw/arm_gic: Remove stray hardcoded tab
hw/arm_gic: gic_set_pending_private() is NVIC only
hw/arm_gic: Use NVIC instead of LEGACY_INCLUDED_GIC define
hw/arm_gic: Make gic_reset a sysbus reset function
hw/arm11mpcore: Convert to using sysbus GIC device
hw/exynos4210_gic: Convert to using sysbus GIC
hw/realview_gic: switch to sysbus GIC
hw/a9mpcore: Switch to using sysbus GIC
hw/a15mpcore: switch to using sysbus GIC
hw/arm_gic: Make the GIC its own sysbus device
hw/arm_gic: Expose PPI inputs as gpio inputs
hw/arm_gic: Move gic_get_current_cpu into arm_gic.c
hw/arm_gic: Move NCPU definition to arm_gic.c
hw/exynos4210_combiner.c: Drop excessive read/write access check.
ARM: Exynos4210: Drop gic_cpu_write() after initialization.
Fix bit test in Exynos4210 UART emulation to use & instead of &&
The function gic_set_pending_private() is now used by the NVIC
only (for the GIC we now set PPI interrupts via gpio lines and
gic_set_irq()). So make it #ifdef NVIC and remove the 'attribute
unused' annotation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now all the A profile cores have been switched to use the standalone
sysbus GIC, the only remaining code which #includes arm_gic.c is
the v7M NVIC. The coupling is much closer here so it's not so
easily disentangled. For now, add a comment about how arm_gic.c
is compiled, and assume that the NVIC always includes arm_gic.c
and the non-NVIC GIC is always compiled standalone.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make gic_reset a sysbus reset function, so we actually
reset the GIC on system reset rather than only at init.
For the NVIC this requires us also to implement reset
of the SysTick.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert the Exynos GIC code to use the standalone sysbus
GIC device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Evgeny Voevodin <e.voevodin@samsung.com>
Switch the a9mpcore to using the sysbus GIC device rather
than having the a9mp private memory region device subclass
the GIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Compile arm_gic.c as a standalone C file to produce a self contained
sysbus GIC device. Support the legacy usage by #include of the .c file
by making those users #define LEGACY_INCLUDED_GIC, so we can convert
them one by one.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Evgeny Voevodin <e.voevodin@samsung.com>
Expose the Private Peripheral Interrupt inputs as GPIO inputs.
The layout of the GPIO array is thus:
[0..N-1] SPIs
[N..N+31] PPIs for CPU 0
[N+32..N+63] PPIs for CPU 1
...
Treating PPIs as being another kind of input line is in line with the
GIC architecture specification, where they are clearly described that
way. The 11MPCore TRM is a bit more ambiguous, but there is no practical
difference between "set PPI X as pending" and "0->1 transition on a
PPI input line configured as edge triggered", and PPIs are always
edge triggered, so this change won't affect behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the gic_get_current_cpu() function into arm_gic.c.
There are only two implementations: (1) "get the index
of the currently executing CPU", used by all multicore
GICs, and (2) "always 0", used by all GICs instantiated
with a single CPU interface (the Realview board GIC and
the v7M NVIC). So we can move this into the main GIC
source file.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Evgeny Voevodin <e.voevodin@samsung.com>
Move the NCPU definition to arm_gic.c: the maximum number
of CPU interfaces is defined by the GIC architecture specification
to be 8, so we don't need to have this #define in each of the
sources files which currently includes arm_gic.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Evgeny Voevodin <e.voevodin@samsung.com>
Access to reserved area at offset higher than 0x3c is allowed in
External Combiner. Samsung Galaxy Kernel implements this. So, drop
excessive checks in read/write functions.
Signed-off-by: Evgeny Voevodin <e.voevodin@samsung.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove gic_cpu_write() call after initialization that was emulating
functionality of earliest SOC bootloader which enables external
GIC CPU1 interface. Instead introduce Exynos4210-specific secondary
CPU bootloader, which enables both Internal and External GIC CPU1
interfaces.
Signed-off-by: Evgeny Voevodin <e.voevodin@samsung.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Often when a guest is stopped from the qemu console, it will report spurious
soft lockup warnings on resume. There are kernel patches being discussed that
will give the host the ability to tell the guest that it is being stopped and
should ignore the soft lockup warning that generates. This patch uses the qemu
Notifier system to tell the guest it is about to be stopped.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
We use a 2 byte ioeventfd for virtio memory,
add support for this.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit afe0a59535 ("rtl8139: support byte
read to TxStatus registers") reused rtl8139_TxStatus_read() for reading
TxAddr registers. It relies on the fact that TxStatus[] and TxAddr[]
are adjacent.
This causes a gcc warning because the compiler can detect that array
access is out-of-bounds:
hw/rtl8139.c:2501:27: error: array subscript is above array bounds [-Werror=array-bounds]
This patch refactors the function so that we don't rely on out-of-bounds
accesses.
Cc: Jason Wang <jasonwang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Currently the virtio balloon device, when using the virtio-pci interface
advertises itself with PCI class code MEMORY_RAM. This is wrong; the
balloon is vaguely related to memory, but is nothing like a PCI memory
device in the meaning of the class code, and this code is not required
or suggested by the virtio PCI specification.
Worse, this patch causes problems on the pseries machine, because the
firmware, seeing this class code, advertises the device as memory in the
device tree, and then a guest kernel bug causes it to see this "memory"
before the real system memory, leading to a crash in early boot.
This patch fixes the problem by removing the bogus PCI class code on the
balloon device. The backwards compatibility PC machines get new compat
properties so that they don't change.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ivshmem used msix but didn't call it on either reset or
config write paths. This used to partically work since
guests don't use all of msi-x configuration fields,
and reset is rarely used, but the patch 'msix: track function masked
in pci device state' broke that. Fix by adding appropriate calls.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reported-by: Cam Macdonell <cam@cs.ualberta.ca>
Tested-by: Cam Macdonell <cam@cs.ualberta.ca>
It's clear from the surrounding code that
start < end so it's enough to assert end < log_size.
However, it's better to make this explicit in case
we refactor the code again.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the vhost log is resized, we want to sync up to
the size of the old log. With that end address in place,
ignore regions that start after then end rather than
hitting assert.
This also addresses the following crash report:
When migrating a vm using vhost-net we hit the following assertion:
qemu-kvm: /usr/src/packages/BUILD/qemu-kvm-0.15.1/hw/vhost.c:30:
vhost_dev_sync_region: Assertion `start / (0x1000 * (8 *
sizeof(vhost_log_chunk_t))) < dev->log_size' failed.
The cases which the end < start check is intended to catch, such as
for vga video memory, will also likely trigger the assertion.
Reorder the code to handle this correctly.
Reported-by: Josh Durgin <josh.durgin@dreamhost.com>
Signed-off-by: Bruce Rogers <brogers@suse.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make it easier to add compat properties, by
adding macros for properties duplicated across
machine types.
Note: there could be bugs in compat properties,
this patch does not attempt to address them,
the code is bug for bug identical to the original.
Tested by: generated a preprocessed file, sorted and
compared to sorted original.
Lightly tested on x86_64.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is a typo in i440FX init code. This is causing problems when
somebody wants to access the 64bit PCI range.
Signed-off-by: Alexey Korolev <alexey.korolev@endace.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* commit 'ff71f2e8cacefae99179993204172bc65e4303df': (21 commits)
rtl8139: do the network/host communication only in normal operating mode
rtl8139: correctly check the opmode
net: move compute_mcast_idx() to net.h
rtl8139: support byte read to TxStatus registers
rtl8139: remove unused marco
rtl8139: limit transmission buffer size in c+ mode
pci_regs: Add PCI_EXP_TYPE_PCIE_BRIDGE
virtio-net: add DATA_VALID flag
pci_bridge: upper 32 bit are long registers
pci: fix bridge IO/BASE
pcie: drop functionality moved to core
pci: set memory type for memory behind the bridge
pci: add standard bridge device
slotid: add slot id capability
shpc: standard hot plug controller
pci_bridge: user-friendly default bus name
pci: make another unused extern function static
pci: don't export an internal function
pci_regs: Fix value of PCI_EXP_TYPE_RC_EC.
pci: Do not check if a bus exist in pci_parse_devaddr.
...
* kwolf/for-anthony: (46 commits)
qed: remove incoming live migration blocker
qed: honor BDRV_O_INCOMING for incoming live migration
migration: clear BDRV_O_INCOMING flags on end of incoming live migration
qed: add bdrv_invalidate_cache to be called after incoming live migration
blockdev: open images with BDRV_O_INCOMING on incoming live migration
block: add a function to clear incoming live migration flags
block: Add new BDRV_O_INCOMING flag to notice incoming live migration
block stream: close unused files and update ->backing_hd
qemu-iotests: Fix call syntax for qemu-io
qemu-iotests: Fix call syntax for qemu-img
qemu-iotests: Test unknown qcow2 header extensions
qemu-iotests: qcow2.py
sheepdog: fix send req helpers
sheepdog: implement SD_OP_FLUSH_VDI operation
block: bdrv_append() fixes
qed: track dirty flag status
qemu-img: add dirty flag status
qed: image fragmentation statistics
qemu-img: add image fragmentation statistics
block: document job API
...
This FIXME has already been actioned. Deleted comment.
Signed-off-by: Peter A. G. Crosthwaite <peter.crosthwaite@petalogix.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
It currently uses qerror_report(), but next commit will convert
the drive_del command to the QAPI and this requires using
error_set().
One particularity of qerror_report() is that it knows when it's
running on monitor context or command-line context and prints the
error message accordingly. error_set() doesn't do this, so we
have to be careful not to drop error messages.
qdev_unplug() has three kinds of usages:
1. It's called when hot adding a device fails, to undo anything
that has been done before hitting the error
2. It's called by function monitor functions like device_del(),
to unplug a device
3. It's used by xen_platform.c in a way that doesn't _seem_ to
be in monitor context
Only item 2 can print an error message to the user, this commit
maintains that.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
The official spelling is QEMU.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
[blauwirbel@gmail.com: fixed comment style in hw/sun4m.c]
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Currently dma_bdrv_io() takes a 'to_dev' boolean parameter to
determine the direction of DMA it is emulating. We already have a
DMADirection enum designed specifically to encode DMA directions.
This patch uses it for dma_bdrv_io() as well. This involves removing
the DMADirection definition from the #ifdef it was inside, but since that
only existed to protect the definition of dma_addr_t from places where
config.h is not included, there wasn't any reason for it to be there in
the first place.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Storage interfaces like virtio-blk can be configured with block size
information so that the guest can take advantage of efficient I/O
request sizes.
According to the SCSI Block Commands (SBC) standard a device's block
size is "almost always greater than one byte and may be a multiple of
512 bytes". QEMU currently has a 512 byte minimum block size because
the block layer functions work at that granularity. Furthermore, the
block size should be a power of 2 because QEMU calculates bitmasks from
the value.
Introduce a "blocksize" property type so devices can enforce these
constraints on block size values. If the constraints are relaxed in the
future then this property can be updated.
Introduce the new PropertyValueNotPowerOf2 QError so QMP clients know
exactly why a block size value was rejected.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the user to specify a disk's World Wide Name.
Linux guests can address disks by their unique World Wide Name number
(e.g. /dev/disk/by-id/wwn-0x5001517959123522). This patch adds support
for assigning a World Wide Name number to a virtual IDE disk.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
strncpy may not null-terminate the destination string.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow the user to override the default disk model name "QEMU HARDDISK".
Some Linux distributions use the /dev/disk/by-id/scsi-SATA_name-of-disk-
model_serial addressing scheme when refering to partitions in /etc/fstab
and elsewhere. This causes problems when starting a disk image taken from
an existing physical server under qemu, because when running under qemu
name-of-disk-model is always "QEMU HARDDISK".
This patch introduces a model=s option which in combination with the
existing serial=s option can be used to fake the disk the operating
system was previously on, allowing the OS to boot properly.
Cc: kwolf@redhat.com
Signed-off-by: Floris Bos <dev@noc-ps.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
And remove several block_int.h inclusions that should not be there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The vector interrupt has higher priority than interrupt_level_n.
Also check only interrupt_level_n concurency when TL > 0, the traps of
other types may be nested.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Don't produce stray irq 5, don't overwrite ivec_data if still busy with
processing of the previous interrupt.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
A strong limitation of QOM right now is that unconverted ports
(e.g. all...) do not give a canonical path to devices that are
part of the board. This in turn makes it impossible to replace
PROP_PTR with a QOM link for example.
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We want the composition tree to to be in order by the time we call
qdev_init, so that a single set of the toplevel realize property can
propagate all the way down the composition tree.
This is not the case so far. Unfortunately, this is incompatible
with calling qdev_init in the constructor wrappers for devices,
so for now we need to unattach some devices that are created through
those wrappers. This will be fixed by removing qdev_init and instead
setting the toplevel realize property after machine init.
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This is QOM "mkdir -p". It is useful when referring to
container objects such as "/machine".
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We never actually clear the TEMT (transmit sending register empty) flag when
populating the TSR. We set the flag, but since it's never cleared, setting it
is sort of pointless..
I found this with a unit test case.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
I'm not sure if the retry logic has ever worked when not using FIFO mode. I
found this while writing a test case although code inspection confirms it is
definitely broken.
The TSR retry logic will never actually happen because it is guarded by an
'if (s->tsr_rety > 0)' but this is the only place that can ever make the
variable greater than zero. That effectively makes the retry logic an 'if (0)'.
I believe this is a typo and the intention was >= 0. Once this is fixed though,
I see double transmits with my test case. This is because in the non FIFO
case, serial_xmit may get invoked while LSR.THRE is still high because the
character was processed but the retransmit timer was still active.
We can handle this by simply checking for LSR.THRE and returning early. It's
possible that the FIFO paths also need some attention.
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This bug existed since the first commit. Fortunately, the affected
registers have no functionality in qemu. This will only prevent the
following warning:
milkymist_vgafb: write access to unknown register 0x00000034
Signed-off-by: Michael Walle <michael@walle.cc>
The new version introduces the following new registers:
- SoC clock frequency: read-only of system clock used on the SoC
- debug scratchpad: 8 bit scratchpad register
- debug write lock: write once register, without any function on QEMU
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since /i440fx/piix3 is being removed from the composition tree, the
IO-APIC is placed under /i440fx. This is wrong and should be changed
as soon as the /i440fx/piix3 path is put back.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This lets the user specify the desired semantics. By default, the RTC
will follow adjustments from the host's NTP client, and will remain in
sync when the virtual machine is stopped. The previous behavior, which
provides determinism with both icount and qtest, remains available with
"-rtc clock=vm".
pl031 supports migration, so we need to convert the time base from
rtc_clock to vm_clock and back for backwards compatibility. (The
rtc_clock may not be synchronized on the two machines, especially with
savevm/loadvm, so the conversion is needed anyway. And since any time
base will do, why not pick the one base that is backwards compatible).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This lets the user specify the desired semantics. By default, the RTC
will follow adjustments from the host's NTP client. "-rtc clock=vm" will
improve determinism with both icount and qtest. Finally, the previous
behavior is available with "-rtc clock=rt".
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The output of the pulse generator needs to be deterministic when
running in -icount mode, and to remain constant whenever the VM is
stopped. So the right clock to use is vm_clock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* sstabellini/disk_io:
xen_disk: when using AIO flush after the operation is completed
xen_disk: open disk with BDRV_O_NOCACHE | BDRV_O_CACHE_WB | BDRV_O_NATIVE_AIO
We need to detach the blkdev from the BlockDriverState before calling
bdrv_delete.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
