After the start of postcopy migration there are some non-dirty pages which have
already been migrated. These pages are no longer needed on the source vm so that
we can free them and it doen't hurt to complete the migration.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-Id: <20170203152321.19739-4-pbutsykin@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
This feature frees the migrated memory on the source during postcopy-ram
migration. In the second step of postcopy-ram migration when the source vm
is put on pause we can free unnecessary memory. It will allow, in particular,
to start relaxing the memory stress on the source host in a load-balancing
scenario.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-Id: <20170203152321.19739-3-pbutsykin@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Manually merged in Pavel's 'migration: madvise error_report fixup!'
Cosmetic patch. The use of ms variable instead of migrate_get_current()
looks nicer, especially when there reuse.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Message-Id: <20170203152321.19739-2-pbutsykin@virtuozzo.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
I'm leaving my job at Red Hat, this email address will stop working next week.
Update it to one that I will have access to later.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Message-Id: <1486120433-11628-1-git-send-email-amit.shah@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
I'm switching jobs, and I'm not sure I can continue maintaining migration.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Message-Id: <1486120416-11566-1-git-send-email-amit.shah@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFGBAABCAAwFiEEkb62CjDbPohX0Rgp9AfbAGHVz0AFAlifubwSHG1yZWl0ekBy
ZWRoYXQuY29tAAoJEPQH2wBh1c9ASDEH+gLn/7Xm29Lex3SZFzuTQx+/mmXB756M
q/lsV7q4f18QH7pMdf02LPlPnPcbmYZnGcm65ezGzZ1y0e3+jAdzF98gLfPYmXxZ
qZREgOH+zmH/IEx1Iq62I3BNYvi0zk/z/PoHNtm+1rrl3oTx1GgYgj5dDYXA8gHl
IYWHLexUqQtEbUplqMSOviALuoMscIvAsFsPImhl8Mq4d4ft3RuNJdCqW+K5AkqK
i0mQTnuuTCcnBhNMr+kYFGAAsABVsb+apcj7Tsq2phazLv+K5h8zzJrtci02E2M2
CwOo3N/aNkw/Yizdzv1mslYNJb9dYcx6aRiJp+Xcuy1qV0LXEmCZxYs=
=qWhR
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2017-02-12' into staging
Block patches
# gpg: Signature made Sun 12 Feb 2017 01:26:20 GMT
# gpg: using RSA key 0xF407DB0061D5CF40
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>"
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/maxreitz/tags/pull-block-2017-02-12: (21 commits)
qemu-img: Avoid setting ret to unused value in img_convert()
qemu-img: Use qemu_strtoul() rather than raw strtoul()
qemu-io: don't allow I/O operations larger than BDRV_REQUEST_MAX_BYTES
qcow2: Optimize the refcount-block overlap check
qemu-io: Add failure regression tests
qemu-iotests: Add _unsupported_fmt helper
qemu-io: Return non-zero exit code on failure
block/nfs: fix naming of runtime opts
block/nfs: fix NULL pointer dereference in URI parsing
block: bdrv_invalidate_cache: invalidate children first
block/qapi: reduce the execution time of qmp_query_blockstats
block/qapi: reduce the coupling between the bdrv_query_stats and bdrv_query_bds_stats
qemu-iotest: test to lookup protocol-based image with relative backing
qemu-iotests: Don't create fifos / pidfiles with protocol paths
block: check full backing filename when searching protocol filenames
block/vmdk: Fix the endian problem of buf_len and lba
iotests: record separate timings per format,protocol pair
iotests: Fix reference output for 059
qapi: Tweak error message of bdrv_query_image_info
qemu-img: Improve commit invalid base message
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity points out that we assign the return value from
bdrv_snapshot_load_tmp() to 'ret' in img_convert(), but then
never use that variable. (We check for failure by looking
at local_err instead.) Drop the unused assignment, bringing
the call into line with the following call to
bdrv_snapshot_laod_tmp_by_id_or_name().
(Fixes CID 1247240.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1486744104-15590-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Some of the argument parsing in qemu-img uses strtoul() to parse
integer arguments. This is tricky to get correct and in fact the
code does not get it right, because it assigns the result of
strtoul() to an 'int' variable and then tries to check for > INT_MAX.
Coverity correctly complains that the comparison is always false.
Rewrite to use qemu_strtoul(), which has a saner convention for
reporting conversion failures.
(Fixes CID 1356421, CID 1356422, CID 1356423.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1486744104-15590-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Passing a request size larger than BDRV_REQUEST_MAX_BYTES to any of the
I/O commands results in an error. While 'read' and 'write' handle the
error correctly, 'aio_read' and 'aio_write' hit an assertion:
blk_aio_read_entry: Assertion `rwco->qiov->size == acb->bytes' failed.
The reason is that the QEMU I/O code cannot handle request sizes
larger than BDRV_REQUEST_MAX_BYTES, so this patch makes qemu-io check
that all values are within range.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 79f66648c685929a144396bda24d13a207131dcf.1485878688.git.berto@igalia.com
[mreitz: Use BDRV_REQUEST_MAX_BYTES instead of INT_MAX]
Signed-off-by: Max Reitz <mreitz@redhat.com>
The metadata overlap checks introduced in a40f1c2add help detect
corruption in the qcow2 image by verifying that data writes don't
overlap with existing metadata sections.
The 'refcount-block' check in particular iterates over the refcount
table in order to get the addresses of all refcount blocks and check
that none of them overlap with the region where we want to write.
The problem with the refcount table is that since it always occupies
complete clusters its size is usually very big. With the default
values of cluster_size=64KB and refcount_bits=16 this table holds 8192
entries, each one of them enough to map 2GB worth of host clusters.
So unless we're using images with several TB of allocated data this
table is going to be mostly empty, and iterating over it is a waste of
CPU. If the storage backend is fast enough this can have an effect on
I/O performance.
This patch keeps the index of the last used (i.e. non-zero) entry in
the refcount table and updates it every time the table changes. The
refcount-block overlap check then uses that index instead of reading
the whole table.
In my tests with a 4GB qcow2 file stored in RAM this doubles the
amount of write IOPS.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170201123828.4815-1-berto@igalia.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add regression tests checking that qemu-io fails with non-zero exit code
when reading non-existing file or using the wrong image format.
Signed-off-by: Nir Soffer <nirsof@gmail.com>
Message-id: 20170201003120.23378-4-nirsof@gmail.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This helper allows adding tests supporting any format expect the
specified formats. This may be useful to test that many formats behave
in a common way.
Signed-off-by: Nir Soffer <nirsof@gmail.com>
Message-id: 20170201003120.23378-3-nirsof@gmail.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The result of openfile was not checked, leading to failure deep in the
actual command with confusing error message, and exiting with exit code 0.
Here is a simple example - trying to read with the wrong format:
$ touch file
$ qemu-io -f qcow2 -c 'read -P 1 0 1024' file; echo $?
can't open device file: Image is not in qcow2 format
no file open, try 'help open'
0
With this patch, we fail earlier with exit code 1:
$ ./qemu-io -f qcow2 -c 'read -P 1 0 1024' file; echo $?
can't open device file: Image is not in qcow2 format
1
Failing earlier, we don't log this error now:
no file open, try 'help open'
But some tests expected it; the line was removed from the test output.
Signed-off-by: Nir Soffer <nirsof@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20170201003120.23378-2-nirsof@gmail.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
commit 94d6a7a accidentally left the naming of runtime opts and QAPI
scheme inconsistent. As one consequence passing of parameters in the
URI is broken. Sync the naming of the runtime opts to the QAPI
scheme.
Please note that this is technically backwards incompatible with the 2.8
release, but the 2.8 release is the only version that had the wrong naming.
Furthermore release 2.8 suffered from a NULL pointer dereference during
URI parsing.
Fixes: 94d6a7a76e
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Message-id: 1485942829-10756-3-git-send-email-pl@kamp.de
[mreitz: Fixed commit message]
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
parse_uint_full wants to put the parsed value into the
variable passed via its second argument which is NULL.
Fixes: 94d6a7a76e
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1485942829-10756-2-git-send-email-pl@kamp.de
Signed-off-by: Max Reitz <mreitz@redhat.com>
Current implementation invalidates firstly parent bds and then its
children. This leads to the following bug:
after incoming migration, in bdrv_invalidate_cache_all:
1. invalidate parent bds - reopen it with BDRV_O_INACTIVE cleared
2. child is not yet invalidated
3. parent check that its BDRV_O_INACTIVE is cleared
4. parent writes to child
5. assert in bdrv_co_pwritev, as BDRV_O_INACTIVE is set for child
This patch fixes it by just changing invalidate sequence: invalidate
children first.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20170131112308.54189-1-vsementsov@virtuozzo.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
In order to reduce the execution time, this patch optimize
the qmp_query_blockstats():
Remove the next_query_bds function.
Remove the bdrv_query_stats function.
Remove some judgement sentence.
The original qmp_query_blockstats calls next_query_bds to get
the next objects in each loops. In the next_query_bds, it checks
the query_nodes and blk. It also call bdrv_query_stats to get
the stats, In the bdrv_query_stats, it checks blk and bs each
times. This waste more times, which may stall the main loop a
bit. And if the disk is too many and donot use the dataplane
feature, this may affect the performance in main loop thread.
This patch removes that two functions, and makes the structure
clearly.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Message-id: 1484467275-27919-3-git-send-email-douly.fnst@cn.fujitsu.com
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[mreitz: Removed duplicate info->value assignment]
Signed-off-by: Max Reitz <mreitz@redhat.com>
The bdrv_query_stats and bdrv_query_bds_stats functions need to call
each other, that increases the coupling. it also makes the program
complicated and makes some unnecessary tests.
Remove the call from bdrv_query_bds_stats to bdrv_query_stats, just
take some recursion to make it clearly.
Avoid testing whether the blk is NULL during querying the bds stats.
It is unnecessary.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Message-id: 1484467275-27919-2-git-send-email-douly.fnst@cn.fujitsu.com
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
This test uses NFS and block-stream to force a lookup of a backing
image that has a relative filename, but a full backing image name
with the protocol path intact.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: 1a7a3d6e6d8af36cd5b47ed6ea93b5a9ededf81b.1485392617.git.jcody@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Trying to create, use, and remove fifos and pidfiles on protocol paths
(e.g. nfs://localhost/scratch/qemu-nbd.pid) is obviously broken.
Use the local $TEST_DIR path before it is 'protocolized' for these
files.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: bb4a731a35bc4ac81fe3db17479dd686315317c7.1485392617.git.jcody@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
In bdrv_find_backing_image(), if we are searching an image for a backing
file that contains a protocol, we currently only compare unmodified
paths.
However, some management software will change the backing filename to be
a relative filename in a path. QEMU is able to handle this fine,
because internally it will use path_combine to put together the full
protocol URI.
However, this can lead to an inability to match an image during a QAPI
command that needs to use bdrv_find_backing_image() to find the image,
when it is searched by the full URI.
When searching for a protocol filename, if the straight comparison
fails, this patch will also compare against the full backing filename to
see if that is a match.
Signed-off-by: Jeff Cody <jcody@redhat.com>
Message-id: c2d025adca8a2b665189e6f4cf080f44126d0b6b.1485392617.git.jcody@redhat.com
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
The problem was triggered by qemu-iotests case 055. It failed when it
was comparing the compressed vmdk image with original test.img.
The cause is that buf_len in vmdk_write_extent wasn't converted to
little-endian before it was stored to disk. But later vmdk_read_extent
read it and converted it from little-endian to cpu endian.
If the cpu is big-endian like s390, the problem will happen and
the data length read by vmdk_read_extent will become invalid!
The fix is to add the conversion in vmdk_write_extent, meanwhile,
repair the endianness problem of lba field which shall also be converted
to little-endian before storing to disk.
Cc: qemu-stable@nongnu.org
Signed-off-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-id: 20161216052040.53067-2-haoqf@linux.vnet.ibm.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
The 'check' program records timings for each test that
is run. These timings are only valid, however, for a
particular format/protocol combination. So if frequently
running 'check' with a variety of different formats or
protocols, the times printed can be very misleading.
Instead of having a single 'check.time' file, maintain
multiple 'check.time-$IMGPROTO-$IMGFMT' files.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170103160556.9895-1-berrange@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
It was broken by efaa7c4eeb when it dropped the device name "image"
from BB API. Now this error message text is updated again, sync it up.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 20170119130759.28319-3-famz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
@bs doesn't always have a device name, such as when it comes from
"qemu-img info". Report file name instead.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 20170119130759.28319-2-famz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
When trying to invoke qemu-img commit with a base image file name that
is not part of the top image's backing chain, the user receives a rather
plain "Base not found" error message. This is not really helpful because
it does not explain what "not found" means, potentially leaving the user
wondering why qemu cannot find a file despite it clearly existing in the
file system.
Improve the error message by clarifying that "not found" means "not
found in the top image's backing chain".
Reported-by: Ala Hino <ahino@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20161201020508.24417-1-mreitz@redhat.com
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
If TEST_DIR is set to /tmp, test case 144 will fail. The reason is that
TEST_DIR resembles 144's test image name tmp.qcow2.
When 144 is testing $TEST_DIR/tmp.qcow2, it wants to replace
$TEST_DIR/tmp.qcow2 to TEST_DIR/tmp.qcow2, but actually it will fail
and get TEST_DIRTEST_DIR.qcow2 in this case.
The fix is just to modify the code to replace $TEST_DIR/ with TEST_DIR/.
Signed-off-by: QingFeng Hao <haoqf@linux.vnet.ibm.com>
Message-id: 20161216054723.96055-2-haoqf@linux.vnet.ibm.com
Reviewed-by: Eric Blake <eblake@redhat.com>
[mreitz: Fixed commit message and dropped superfluous escaping]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Both devices seem to be specific to the ARM platform. It's confusing
for the users if they show up on other target architectures, too
(e.g. when the user runs QEMU with "-device ?" to get a list of
supported devices). Thus let's introduce proper configuration switches
so that the devices are only compiled and included when they are
really required.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The device has "bridge" in its name, so it should obviously be in
the category DEVICE_CATEGORY_BRIDGE.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Previous IGD, up through Broadwell, only seem to write GTT values into
the first 1MB of space allocated for the BDSM, but clearly the GTT
can be multiple MB in size. Our test in vfio_igd_quirk_data_write()
correctly filters out indexes beyond 1MB, but given the 1MB mask we're
using, we re-apply writes only to the first 1MB of the guest allocated
BDSM.
We can't assume either the host or guest BDSM is naturally aligned, so
we can't simply apply a different mask. Instead, save the host BDSM
and do the arithmetic to subtract the host value to get the BDSM
offset and add it to the guest allocated BDSM.
Reported-by: Alexander Indenbaum <alexander.indenbaum@gmail.com>
Tested-by: Alexander Indenbaum <alexander.indenbaum@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The size of a segment is not necessarily a power of 2.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1486648058-520-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HW works fine in normal read mode with dummy bytes being set. So let's
check this case to not transfer bytes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1486648058-520-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The flash devices used for the FMC controller (BMC firmware) are well
defined for each Aspeed machine and are all smaller than the default
mapping window size, at least for CE0 which is the chip the SoC boots
from.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1486648058-520-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
write_boot_rom() does not check for negative values. This is more a
problem for coverity than the actual code as the size of the flash
device is checked when the m25p80 object is created. If there is
anything wrong with the backing file, we should not even reach that
path.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1486648058-520-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fw-cfg recently learned how to directly access guest memory and does so in
cache coherent fashion. Tell the guest about that fact when it's using DT.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1486644810-33181-5-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fw-cfg recently learned how to directly access guest memory and does so in
cache coherent fashion. Tell the guest about that fact when it's using ACPI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1486644810-33181-4-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Virtio-mmio devices can directly access guest memory and do so in cache
coherent fashion. Tell the guest about that fact when it's using ACPI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1486644810-33181-3-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU emulated hardware is always dma coherent with its guest. We do
annotate that correctly on the PCI host controller, but left out
virtio-mmio.
Recent kernels have started to interpret that flag rather than take
dma coherency as granted with virtio-mmio. While that is considered
a kernel bug, as it breaks previously working systems, it showed that
our dt description is incomplete.
This patch adds the respective marker that allows guest OSs to evaluate
that our virtio-mmio devices are indeed cache coherent.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1486644810-33181-2-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch contains several fixes to enable vPMU under TCG mode. It
first removes the checking of kvm_enabled() while unsetting
ARM_FEATURE_PMU. With it, the .pmu option can be used to turn on/off vPMU
under TCG mode. Secondly the PMU node of DT table is now created under TCG.
The last fix is to disable the masking of PMUver field of ID_AA64DFR0_EL1.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1486504171-26807-5-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds access support for PMINTENSET_EL1.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1486504171-26807-4-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to support Linux perf, which uses PMXEVTYPER register,
this patch adds read/write access support for PMXEVTYPER. The access
is CONSTRAINED UNPREDICTABLE when PMSELR is not 0x1f. Additionally
this patch adds support for PMXEVTYPER_EL0.
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1486504171-26807-3-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds support for AArch64 register PMSELR_EL0. The existing
PMSELR definition is revised accordingly.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: Moved #ifndef CONFIG_USER_ONLY to cover new regdefs]
Message-id: 1486504171-26807-2-git-send-email-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AHCI emulation code supports 64-bit addressing and should advertise this
fact in the Host Capabilities register. Both Linux and Windows drivers test
this bit to decide if the upper 32 bits of various registers may be written
to, and at least some versions of Windows have a bug where DMA is attempted
with an address above 4GB but, in the absence of HOST_CAP_64, the upper 32
bits are left unititialized which leads to a memory corruption.
[Maintainer edit:
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=1411105,
which affects Windows Server 2008 SP2 in some cases.]
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Message-id: 1484305370-6220-1-git-send-email-lprosek@redhat.com
[Amended commit message --js]
Signed-off-by: John Snow <jsnow@redhat.com>
This reverts commit 5858dd1801.
Conflicts:
hw/display/cirrus_vga.c
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 1486645341-5010-2-git-send-email-kraxel@redhat.com
The blit_region_is_unsafe checks don't work correctly for the
patterncopy source. It's a fixed-sized region, which doesn't
depend on cirrus_blt_{width,height}. So go do the check in
cirrus_bitblt_common_patterncopy instead, then tell blit_is_unsafe that
it doesn't need to verify the source. Also handle the case where we
blit from cirrus_bitbuf correctly.
This patch replaces 5858dd1801.
Security impact: I think for the most part error on the safe side this
time, refusing blits which should have been allowed.
Only exception is placing the blit source at the end of the video ram,
so cirrus_blt_srcaddr + 256 goes beyond the end of video memory. But
even in that case I'm not fully sure this actually allows read access to
host memory. To trick the commit 5858dd18 security checks one has to
pick very small cirrus_blt_{width,height} values, which in turn implies
only a fraction of the blit source will actually be used.
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 1486645341-5010-1-git-send-email-kraxel@redhat.com
