BookS does not take single step interrupts on completion of rfi and
similar (rfid, hrfid, rfscv). This is not a completely clean way to
do it, but in general non-branch instructions that change NIP on
completion are excluded.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Improve the emulation accuracy of the single step and branch trace
interrupts for v2.07S. Set SRR1[33]=1, and set SIAR to completed
instruction address.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Single-step interrupts are suppressed if the nip is between 0x100 and
0xf00. This has been the case for a long time and it's not clear what
the intention is. Likely either an attempt to suppress trace interrupts
for instructions that cause an interrupt on completion, or a workaround
to prevent software tripping over itself single stepping its interrupt
handlers.
BookE interrupt vectors are set by IVOR registers, and BookS has AIL
modes and new interrupt types, so there are many interrupts including
the debug interrupt which can be outside this range. So any effect it
might have had does not cover most cases (including Linux on recent
BookS CPUs).
Remove this special case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg : fixed typo in commit logs ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Linux sets these to control cache flush behaviour on Power9. Supervisor
and hypervisor are allowed to write, and reads are noops.
Add implementations to avoid noisy messages when booting Linux under the
pseries machine with guest_errors enabled.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Change radix model to always generate a storage interrupt when the R/C
bits are not set appropriately in a PTE instead of setting the bits
itself. According to the ISA both behaviors are valid, but in practice
this change more closely matches behavior observed on the POWER9 CPU.
From the POWER9 Processor User's Manual, Section 4.10.13.1: "When
performing Radix translation, the POWER9 hardware triggers the
appropriate interrupt ... for the mode and type of access whenever
Reference (R) and Change (C) bits require setting in either the guest or
host page-table entry (PTE)."
Signed-off-by: Shawn Anastasio <sanastasio@raptorengineering.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
"qemu/main-loop.h" declares functions related to QEMU's
main loop mutex, which these files don't access. Remove
the unused "qemu/main-loop.h" header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-8-philmd@linaro.org>
All these files only access the translator_ld/st API declared
in "exec/translator.h". The CPU ld/st API from declared in
"exec/cpu_ldst.h" is not used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-5-philmd@linaro.org>
Since commit c2eff582a3 ("target/ppc: PMU basic cycle count for
pseries TCG") pmu_update_cycles() uses QEMU_CLOCK_VIRTUAL and
calls qemu_clock_get_ns(), both defined in "qemu/timer.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230828221314.18435-2-philmd@linaro.org>
Try and make the self reported global hack a little less hackish by
providing a query function instead. As gdb_has_xml was always set if
we negotiated XML we can now use the presence of ->target_xml as the
test instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230829161528.2707696-12-alex.bennee@linaro.org>
Tested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Changes the signature of the target-defined functions for
inserting/removing kvm hw breakpoints. The address and length arguments
are now of vaddr type, which both matches the type used internally in
accel/kvm/kvm-all.c and makes the api target-agnostic.
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230807155706.9580-4-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
kvm_arch_get_default_type() returns the default KVM type. This hook is
particularly useful to derive a KVM type that is valid for "none"
machine model, which is used by libvirt to probe the availability of
KVM.
For MIPS, the existing mips_kvm_type() is reused. This function ensures
the availability of VZ which is mandatory to use KVM on the current
QEMU.
Cc: qemu-stable@nongnu.org
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20230727073134.134102-2-akihiko.odaki@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added doc comment for new function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Until v2.07s, the VRMA page size (L||LP) was encoded in LPCR[VRMASD].
In v3.0 that moved to the partition table PS field.
The powernv machine can now run KVM HPT guests on POWER9/10 CPUs with
this fix and the patch to add ASDR.
Fixes: 3367c62f52 ("target/ppc: Support for POWER9 native hash")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230730111842.39292-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
HDEC is defined to not wake from PM state. There is a check in the HDEC
timer to avoid setting the interrupt if we are in a PM state, but no
check on PM entry to lower HDEC if it already fired. This can cause a
HDECR wake up and QEMU abort with unsupported exception in Power Save
mode.
Fixes: 4b236b621b ("ppc: Initial HDEC support")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230726182230.433945-4-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The ASDR register was introduced in ISA v3.0. It has not been
implemented for HPT. With HPT, ASDR is the format of the slbmte RS
operand (containing VSID), which matches the ppc_slb_t field.
Fixes: 3367c62f52 ("target/ppc: Support for POWER9 native hash")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230726182230.433945-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The change to use translator_use_goto_tb went too far, as the
CF_SINGLE_STEP flag managed by the translator only handles
gdb single stepping and not the architectural single stepping
modeled in DisasContext.singlestep_enabled.
Fixes: 6e9cc373ec ("target/ppc: Use translator_use_goto_tb")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1795
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This implements the VNCIPHER instruction.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This implements the VCIPHER instruction.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This implements the VNCIPHERLAST instruction.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This implements the VCIPHERLAST instruction.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-ID: <20230627115124.19632-7-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
User emulation shouldn't need any of the KVM prototypes
declared in "kvm_ppc.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-ID: <20230627115124.19632-6-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
TYPE_HOST_POWERPC_CPU is used in various places of cpu_init.c,
in order to restrict "kvm_ppc.h" to sysemu, move this QOM-related
definition to cpu-qom.h.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-ID: <20230627115124.19632-5-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Keep a single if/else/endif block checking CONFIG_KVM.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230627115124.19632-3-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
"kvm_ppc.h" declares:
int kvm_handle_nmi(PowerPCCPU *cpu, struct kvm_run *run);
'struct kvm_run' is declared in "sysemu/kvm.h", include it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230627115124.19632-2-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
ppc currently silently accepts invalid real address access. Catch
these and turn them into machine checks on POWER9/10 machines.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-ID: <20230703120301.45313-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
HID is a per-core shared register, skiboot sets this (e.g., setting
HILE) on one thread and that must affect all threads of the core.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <20230705120631.27670-3-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The Power ISA has the concept of sub-processors:
Hardware is allowed to sub-divide a multi-threaded processor into
"sub-processors" that appear to privileged programs as multi-threaded
processors with fewer threads.
POWER9 and POWER10 have two modes, either every thread is a
sub-processor or all threads appear as one multi-threaded processor. In
the user manuals these are known as "LPAR per thread" / "Thread LPAR",
and "LPAR per core" / "1 LPAR", respectively.
The practical difference is: in thread LPAR mode, non-hypervisor SPRs
are not shared between threads and msgsndp can not be used to message
siblings. In 1 LPAR mode, some SPRs are shared and msgsndp is usable.
Thrad LPAR allows multiple partitions to run concurrently on the same
core, and is a requirement for KVM to run on POWER9/10 (which does not
gang-schedule an LPAR on all threads of a core like POWER8 KVM).
Traditionally, SMT in PAPR environments including PowerVM and the
pseries QEMU machine with KVM acceleration behaves as in 1 LPAR mode.
In OPAL systems, Thread LPAR is used. When adding SMT to the powernv
machine, it is therefore preferable to emulate Thread LPAR.
To account for this difference between pseries and powernv, an LPAR mode
flag is added such that SPRs can be implemented as per-LPAR shared, and
that becomes either per-thread or per-core depending on the flag.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <20230705120631.27670-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Currently on PPC64 qemu always dumps the guest memory in
Big Endian (BE) format even though the guest running in Little Endian
(LE) mode. So crash tool fails to load the dump as illustrated below:
Log :
$ virsh dump DOMAIN --memory-only dump.file
Domain 'DOMAIN' dumped to dump.file
$ crash vmlinux dump.file
<snip>
crash 8.0.2-1.el9
WARNING: endian mismatch:
crash utility: little-endian
dump.file: big-endian
WARNING: machine type mismatch:
crash utility: PPC64
dump.file: (unknown)
crash: dump.file: not a supported file format
<snip>
This happens because cpu_get_dump_info() passes cpu->env->has_hv_mode
to function ppc_interrupts_little_endian(), the cpu->env->has_hv_mode
always set for powerNV even though the guest is not running in hv mode.
The hv mode should be taken from msr_mask MSR_HVB bit
(cpu->env.msr_mask & MSR_HVB). This patch fixes the issue by passing
MSR_HVB value to ppc_interrupts_little_endian() in order to determine
the guest endianness.
The crash tool also expects guest kernel endianness should match the
endianness of the dump.
The patch was tested on POWER9 box booted with Linux as host in
following cases:
Host-Endianess Qemu-Target-Machine Qemu-Generated-Guest
Memory-Dump-Format
BE powernv(OPAL/PowerNV) LE
BE powernv(OPAL/PowerNV) BE
LE powernv(OPAL/PowerNV) LE
LE powernv(OPAL/PowerNV) BE
LE pseries(OPAL/PowerNV/pSeries) KVMHV LE
LE pseries TCG LE
Fixes: 5609400a42 ("target/ppc: Set the correct endianness for powernv memory
dumps")
Signed-off-by: Narayana Murty N <nnmlinux@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Message-ID: <20230623072506.34713-1-nnmlinux@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
We can get CPUState from env with env_cpu without going through
PowerPCCPU and casting that.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <28424220f37f51ce97f24cadc7538a9c0d16cb45.1686868895.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Commit 7a3fe174b1 removed usage of POWERPC_SYSCALL_VECTORED, drop
the unused define as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <50adc24f9d408882128e896d8a81a1a059c41836.1686868895.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Some helpers only have a CPUState local to call cpu_interrupt_exittb()
but we can use env_cpu for that and remove the local.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <aa34e449552c6ab52d48938ccbe762fc06adac01.1686868895.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
All powerpc exception handlers share some code when handling machine
check exceptions. Move this to a common function.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <9cfffaa35aa894086dd092af6b0b26f2d62ff3de.1686868895.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
CPUState is rarely needed by this function (only for logging a fatal
error) and it's easy to get from the env parameter so passing it
separately is not necessary.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <f42761401c708fd6e02f7523d9f709b1972e5863.1686868895.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Several instructions and register access require icount reads and are
missing translator_io_start().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230625103700.8992-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
TFMR is the Time Facility Management Register which is specific to
POWER CPUs, and used for the purpose of timebase management (generally
by firmware, not the OS).
Add helpers for the TFMR register, which will form part of the core
timebase facility model in future but for now behaviour is unchanged.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <20230625120317.13877-3-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
POWER book4 (implementation-specific) SPRs are sometimes in their own
functions, but in other cases are mixed with architected SPRs. Do some
spring cleaning on these.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <20230625120317.13877-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
No need to generate TCG-specific decodetree files
when TCG is disabled.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230626140100.67941-1-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The 'kvm_sw_tlb' and 'tlb_dirty' fields introduced in commit
93dd5e852c ("kvm: ppc: booke206: use MMU API") are specific
to KVM and shouldn't be accessed when it is not available.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230624192645.13680-1-philmd@linaro.org>
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230621135633.1649-4-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Doorbells in SMT need to coordinate msgsnd/msgclr and DPDES access from
multiple threads that affect the same state.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
A relatively simple case to begin with, CTRL is a SMT shared register
where reads and writes need to synchronise against state changes by
other threads in the core.
Atomic serialisation operations are used to achieve this.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
TGC SMT emulation needs to know whether it is running with SMT siblings,
to be able to iterate over siblings in a core, and to serialise
threads to access per-core shared SPRs. Add infrastructure to do these
things.
For now the sibling iteration and serialisation are implemented in a
simple but inefficient way. SMT shared state and sibling access is not
too common, and SMT configurations are mainly useful to test system
code, so performance is not to critical.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: fix build breakage with clang ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The top bits of the LEV field of the sc instruction are to be treated as
as a reserved field rather than a reserved value, meaning LEV is
effectively the bottom bit. LEV=0xF should be treated as LEV=1 and be
a hypercall, for example.
This changes the instruction execution to just set lev from the low bit
of the field. Processors which don't support the LEV field will continue
to ignore it.
ISA v3.1 defines LEV to be 2 bits, in order to add the 'sc 2' ultracall
instruction. TCG does not support Ultravisor, so don't worry about
that bit.
Suggested-by: "Harsh Prateek Bora" <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The CTRL register is able to write the bit in the RUN field, which gets
reflected into the TS field which is read-only and contains the state of
the RUN field for all threads in the core.
TCG does not implement SMT, so the correct implementation just requires
mirroring the RUN bit into the first bit of the TS field.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
System call interrupts in ISA v3.1 CPUs add a LEV indication in SRR1
that corresponds with the LEV field of the instruction that caused the
interrupt.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The hypervisor emulation assistance interrupt modifies HEIR to
contain the value of the instruction which caused the exception.
Only TCG raises HEAI interrupts so this can be made TCG-only.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
ISA v3.1 introduced prefix instructions. Among the changes, various
synchronous interrupts report whether they were caused by a prefix
instruction in (H)SRR1.
The case of instruction fetch that causes an HDSI due to access of a
process-scoped table faulting on the partition scoped translation is the
tricky one. As with ISIs and HISIs, this does not try to set the prefix
bit because there is no instruction image to be loaded. The HDSI needs
the originating access type to be passed through to the handler to
distinguish this from HDSIs that fault translating process scoped tables
originating from a load or store instruction (in that case the prefix
bit should be provided).
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: checkpatch issues ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Rather than always performing partition scope page table translation
with access type of 0 (MMU_DATA_LOAD), pass through the processor
access type which first initiated the translation sequence. Process-
scoped page table loads are then set to MMU_DATA_LOAD access type in
the xlate function.
This will allow more information to be passed to the exception
handler in the next patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
powerpc ifetch endianness depends on MSR[LE] so it has to byteswap
after cpu_ldl_code(). This corrects DSISR bits in alignment
interrupts when running in little endian mode.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the Timer Control and Timer Status registers are modified, avoid
calling the KVM backend when not available
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Make sure each CPU gets its state set up for gdb, not just the ones
before PowerPCCPUClass has had its gdb state set up.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Since we *might* have user emulation with softmmu,
replace the system emulation check by !user emulation one.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230613133347.82210-5-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Count exceptions which can be queried with info irq monitor command.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230606220200.7EBCC74635C@zero.eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Rework store conditional to avoid a branch in the success case.
Change some of the variable names and layout while here so
gen_conditional_store more closely matches gen_stqcx_.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230605025445.161932-4-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
larx and stcx. are not defined to order any memory operations.
Remove the barriers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230605025445.161932-3-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Differently-sized larx/stcx. pairs can succeed if the starting address
matches. Add a check to require the size of stcx. exactly match the larx
that established the reservation. Use the term "reserve_length" for this
state, which matches the terminology used in the ISA.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230605025445.161932-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
lqarx does not set cpu_reserve, which causes stqcx. to never succeed.
Cc: qemu-stable@nongnu.org
Fixes: 94bf265867 ("target/ppc: Use atomic load for LQ and LQARX")
Fixes: 57b38ffd0c ("target/ppc: Use tcg_gen_qemu_{ld,st}_i128 for LQARX, LQ, STQ")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230605025445.161932-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Move out checking PID registers into a separate function which makes
mmubooke_check_tlb() simpler and avoids using goto.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <bd84d5f38af0ba2983ccd5c07635db49267c828f.1685448535.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
No nead to store return value and break from loop when we can return
directly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <d470118c3adcbd41b1a91779f6bb7cbdb2b0d346.1685448535.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Make lines shorter and fix indentation in some functions prototypes.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <70952ba2d82141db1cf5cfcf4b227402be575874.1685448535.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This function is the only reason why ppcemb_tlb_check() is not static
to mmu_common.c but it also better fits in mmu_common.c so move it
there.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <b64fd712a773558dea9b84945c57785546c0ae2e.1685448535.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This is only used by one caller so simplify function by removing this
parameter and move the operation to the single place where it's used.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <b21f11ae20e8a8c2e8b5d943f2bff12b5356005a.1685448535.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The get_physical_address() function is a trivial wrapper of
get_physical_address_wtlb() that is only used once. Remove it and call
get_physical_address_wtlb() directly instead.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <302697d63d26caebefaeee1e45352145ebd0318a.1685448535.git.balaton@eik.bme.hu>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The PMU raises a performance monitor exception (causing an interrupt
when MSR[EE]=1) when MMCR0[PMAO] is set, and lowers it when clear.
Wire this up and implement the interrupt delivery for books. Linux perf
record can now collect PMI-driven samples.
fire_PMC_interrupt is renamed to perfm_alert, which matches a bit closer
to the new terminology used in the ISA and distinguishes the alert
condition (e.g., counter overflow) from the PERFM (or EBB) interrupts.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530134313.387252-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
BookS msgsndp instruction to self or DPDES register can cause SDOOR
interrupts which crash QEMU with exception not implemented.
Linux does not use msgsndp in SMT1, and KVM only uses DPDES to cause
doorbells when emulating a SMT guest (which is not the default), so
this has gone unnoticed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230530130526.372701-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
msgclrp matches msgsndp and should clear PPC_INTERRUPT_DOORBELL.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230530130714.373215-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
FCECE does not get cleared according to the ISA v3.1B.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530134313.387252-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Some of the PMU hflags bits can go out of synch, for example a store to
MMCR0 with PMCjCE=1 fails to update hflags correctly and results in
hflags mismatch:
qemu: fatal: TCG hflags mismatch (current:0x2408003d rebuilt:0x240a003d)
This can be reproduced by running perf on a recent machine.
Some of the fragility here is the duplication of PMU hflags calculations.
This change consolidates that in a single place to update pmu-related
hflags, to be called after a well defined state changes.
The post-load PMU update is pulled out of the MSR update because it does
not depend on the MSR value.
Fixes: 8b3d1c49a9 ("target/ppc: Add new PMC HFLAGS")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230530130447.372617-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
ppc hypervisors turn HEAI interrupts into program interrupts injected
into the guest that executed the illegal instruction, if the hypervisor
doesn't handle it some other way.
The nested-hv implementation failed to account for this HEAI->program
conversion. The virtual hypervisor wants to see the HEAI when running
a nested guest, so that interrupt type can be returned to its KVM
caller.
Fixes: 7cebc5db2e ("target/ppc: Introduce a vhyp framework for nested HV support")
Cc: balaton@eik.bme.hu
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230530132127.385001-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Now that gen_icount_io_start() is a simple wrapper to
translator_io_start(), inline it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230602095439.48102-1-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
New wrapper around gen_io_start which takes care of the USE_ICOUNT
check, as well as marking the DisasContext to end the TB.
Remove exec/gen-icount.h.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
From this remove, it's no longer clear what this is attempting
to protect. The last time a use of this define was added to
the source tree, as opposed to merely moved around, was 2008.
There have been many cleanups since that time and this is
no longer required for the build to succeed.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In preparation for compiling tcg/ only once, eliminate
the all_helpers array. Instantiate the info structs for
the generic helpers in accel/tcg/, and the structs for
the target-specific helpers in each translate.c.
Since we don't see all of the info structs at startup,
initialize at first use, using g_once_init_* to make
sure we don't race while doing so.
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
POWER9 DD2.1 and earlier had significant limitations when running KVM,
including lack of "mixed mode" MMU support (ability to run HPT and RPT
mode on threads of the same core), and a translation prefetch issue
which is worked around by disabling "AIL" mode for the guest.
These processors are not widely available, and it's difficult to deal
with all these quirks in qemu +/- KVM, so create a POWER9 DD2.2 CPU
and make it the default POWER9 CPU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-Id: <20230515160201.394587-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Instead of computing an artificial "class" bitmask then converting that
to the fprf value, compute the final value from the start.
Reorder the tests to check the most likely cases first.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230523202507.688859-1-richard.henderson@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
QEMU's PVR value for POWER9 DD2.0 has chip type 1, which is the SMT4
"small core" type that OpenPOWER processors use. QEMU's PVR for all
other POWER9/10 have chip type 0, which "enterprise" systems use.
The difference does not really matter to QEMU (because it does not care
about SMT mode in the target), but for consistency all PVRs should use
the same chip type. We'll go with the SMT4 OpenPOWER type.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20230515160131.394562-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The behaviour of the Address Translation Mode on Interrupt resource is
not consistently supported by all CPU versions or all KVM versions: KVM
HV does not support mode 2, and does not support mode 3 on POWER7 or
early POWER9 processesors. KVM PR only supports mode 0. TCG supports all
modes (0, 2, 3) on CPUs with support for the corresonding LPCR[AIL] mode.
This leads to inconsistencies in guest behaviour and could cause problems
migrating guests.
This was not noticable for Linux guests for a long time because the
kernel only uses modes 0 and 3, and it used to consider AIL-3 to be
advisory in that it would always keep the AIL-0 vectors around, so it
did not matter whether or not interrupts were delivered according to
the AIL mode. Recent Linux guests depend on AIL mode 3 working as
specified in order to support the SCV facility interrupt. If AIL-3 can
not be provided, then H_SET_MODE must return an error to Linux so it can
disable the SCV facility (failure to do so can lead to userspace being
able to crash the guest kernel).
Add the ail-mode-3 capability to specify that AIL-3 is supported. AIL-0
is implied as the baseline, and AIL-2 is no longer supported by spapr.
AIL-2 is not known to be used by any software, but support in TCG could
be restored with an ail-mode-2 capability quite easily if a regression
is reported.
Modify the H_SET_MODE Address Translation Mode on Interrupt resource
handler to check capabilities and correctly return error if not
supported.
KVM has a cap to advertise support for AIL-3.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230515160216.394612-1-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This optional behavior was removed from the ISA in v3.0, see
Summary of Changes preface:
Data Storage Interrupt Status Register for Alignment Interrupt:
Simplifies the Alignment interrupt by remov- ing the Data Storage
Interrupt Status Register (DSISR) from the set of registers modified
by the Alignment interrupt.
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20230515092655.171206-5-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Some 32-bit SPRs are incorrectly implemented as 64-bits on 64-bit
targets.
This changes VRSAVE, DSISR, HDSISR, DAWRX0, PIDR, LPIDR, DEXCR,
HDEXCR, CTRL, TSCR, MMCRH, and PMC[1-6] from to be 32-bit registers.
This only goes by the 32/64 classification in the architecture, it
does not try to implement finer details of SPR implementation (e.g.,
not all bits implemented as simple read/write storage).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-Id: <20230515092655.171206-2-npiggin@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The following commits changed the code such that the fallback to MFSS for MFFSCRN,
MFFSCRNI, MFFSCE and MFFSL on pre 3.0 ISAs was removed and became an illegal instruction:
bf8adfd88b - target/ppc: Move mffscrn[i] to decodetree
394c2e2fda - target/ppc: Move mffsce to decodetree
3e5bce70ef - target/ppc: Move mffsl to decodetree
The hardware will handle them as a MFFS instruction as the code did previously.
This means applications that were segfaulting under qemu when encountering these
instructions which is used in glibc libm functions for example.
The fallback for MFFSCDRN and MFFSCDRNI added in a later patch was also missing.
This patch restores the fallback to MFSS for these instructions on pre 3.0s ISAs
as the hardware decoder would, fixing the segfaulting libm code. It doesn't have
the fallback for 3.0 onwards to match hardware behaviour.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Reviewed-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230510111913.1718734-1-richard.purdie@linuxfoundation.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
No need to roll our own, as this is now provided by tcg.
This was the last use of retxl, so remove that too.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In function do_extractm() the mask is calculated as
dup_const(1 << (element_width - 1)). '1' being signed int
works fine for MO_8,16,32. For MO_64, on PPC64 host
this ends up becoming 0 on compilation. The vextractdm
uses MO_64, and it ends up having mask as 0.
Explicitly use 1ULL instead of signed int 1 like its
used everywhere else.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1536
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Lucas Mateus Castro <lucas.araujo@eldorado.org.br>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Message-Id: <168319292809.1159309.5817546227121323288.stgit@ltc-boston1.aus.stglabs.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The bits in cr reg are grouped into eight 4-bit fields represented
by env->crf[8] and the related calculations should be abstracted to
keep the calling routines simpler to read. This is a step towards
cleaning up the related/calling code for better readability.
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Fabiano Rosas <farosas@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230503093619.2530487-2-harshpb@linux.ibm.com>
[danielhb: add 'const' modifier to fix linux-user build]
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Fix a crash writing to 't3', which is now a constant.
Instead, write the result of the remu to 't0'.
Fixes: 7058ff5231 ("target/ppc: Avoid tcg_const_* in translate.c")
Reported-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[ clg: amend commit log s/t1/t0/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
All remaining uses are strictly read-only.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fix incorrect read from rD.
Avoid adding 0 when rA == 0.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Compute all carry bits in parallel instead of a loop.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All uses are strictly read-only.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All uses are strictly read-only.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All remaining uses are strictly read-only.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Initialize a new temp instead of tcg_const_*.
Fix a pasto in a comment.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
All remaining uses are strictly read-only.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Compute both partial results separately and accumulate
at the end, instead of accumulating in the middle.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move the body out of this large macro.
Use tcg_constant_i64.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Anton Johansson <anjo@rev.ng>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230306175230.7110-16-anjo@rev.ng>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
These inline helpers are all used by target specific code so move them
out of the general header so we don't needlessly pollute the rest of
the API with target specific stuff.
Note we have to include cpu.h in semihosting as it was relying on a
side effect before.
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230302190846.2593720-21-alex.bennee@linaro.org>
Message-Id: <20230303025805.625589-21-richard.henderson@linaro.org>
Translators are no longer required to free tcg temporaries.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The dcblc instruction is used by u-boot in mpc85xx/start.S. Without it,
an illegal istruction exception is generated very early in the boot
process where the processor is not yet able to handle exceptions. See:
https://github.com/u-boot/u-boot/blob/v2023.01/arch/powerpc/cpu/mpc85xx/start.S#L1840
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230130184950.5241-1-shentey@gmail.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Since commit a0e61807a3 ("qapi: Remove QMP events and commands from
user-mode builds") we don't generate the "qapi-commands-machine.h"
header in a user-emulation-only build.
Move the QMP functions from cpu_init.c (which is always compiled)
to monitor.c (which is only compiled when system-emulation
is selected). Rename monitor.c to arm-qmp-cmds.c.
Note ppc_cpu_class_by_name() is used by both file units, so we
expose its prototype in "cpu-qom.h".
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230223155540.30370-5-philmd@linaro.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Since tcg_temp_new is now identical, use that.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In preparation for returning the number of insns generated
via the same pointer. Adjust only the prototypes so far.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When compiling for windows-arm64 using clang-15, it reports a sometimes
uninitialized variable. This seems to be a false positive, as a default
case guards switch expressions, preventing to return an uninitialized
value, but clang seems unhappy with assert(0) definition.
Change code to g_assert_not_reached() fix the warning.
Signed-off-by: Pierrick Bouvier <pierrick.bouvier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230221153006.20300-5-pierrick.bouvier@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The 'hwaddr' type is only available / meaningful on system emulation.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221217172907.8364-5-philmd@linaro.org>
The 'hwaddr' type is only available / meaningful on system emulation.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216215519.5522-5-philmd@linaro.org>
Note that the previous direct reference to reserve_val,
- tcg_gen_ld_i64(t1, cpu_env, (ctx->le_mode
- ? offsetof(CPUPPCState, reserve_val2)
- : offsetof(CPUPPCState, reserve_val)));
was incorrect because all references should have gone through
cpu_reserve_val. Create a cpu_reserve_val2 tcg temp to fix this.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221112061122.2720163-2-richard.henderson@linaro.org>
The 'hwaddr' type is defined in "exec/hwaddr.h" as:
hwaddr is the type of a physical address
(its size can be different from 'target_ulong').
All definitions use the 'HWADDR_' prefix, except TARGET_FMT_plx:
$ fgrep define include/exec/hwaddr.h
#define HWADDR_H
#define HWADDR_BITS 64
#define HWADDR_MAX UINT64_MAX
#define TARGET_FMT_plx "%016" PRIx64
^^^^^^
#define HWADDR_PRId PRId64
#define HWADDR_PRIi PRIi64
#define HWADDR_PRIo PRIo64
#define HWADDR_PRIu PRIu64
#define HWADDR_PRIx PRIx64
#define HWADDR_PRIX PRIX64
Since hwaddr's size can be *different* from target_ulong, it is
very confusing to read one of its format using the 'TARGET_FMT_'
prefix, normally used for the target_long / target_ulong types:
$ fgrep TARGET_FMT_ include/exec/cpu-defs.h
#define TARGET_FMT_lx "%08x"
#define TARGET_FMT_ld "%d"
#define TARGET_FMT_lu "%u"
#define TARGET_FMT_lx "%016" PRIx64
#define TARGET_FMT_ld "%" PRId64
#define TARGET_FMT_lu "%" PRIu64
Apparently this format was missed during commit a8170e5e97
("Rename target_phys_addr_t to hwaddr"), so complete it by
doing a bulk-rename with:
$ sed -i -e s/TARGET_FMT_plx/HWADDR_FMT_plx/g $(git grep -l TARGET_FMT_plx)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230110212947.34557-1-philmd@linaro.org>
[thuth: Fix some warnings from checkpatch.pl along the way]
Signed-off-by: Thomas Huth <thuth@redhat.com>
In addition, use tcg_enabled instead of !kvm_enabled.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Adds checks to the hashst and hashchk instructions to only execute if
enabled by the relevant aspect in the DEXCR and HDEXCR.
This behaviour is guarded behind TARGET_PPC64 since Power10 is
currently the only implementation which has the DEXCR.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Nicholas Miehlbradt <nicholas@linux.ibm.com>
Message-Id: <20221220042330.2387944-3-nicholas@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Define the DEXCR and HDEXCR as special purpose registers.
Each register occupies two SPR indicies, one which can be read in an
unprivileged state and one which can be modified in the appropriate
priviliged state, however both indicies refer to the same underlying
value.
Note that the ISA uses the abbreviation UDEXCR in two different
contexts: the userspace DEXCR, the SPR index which can be read from
userspace (implemented in this patch), and the ultravisor DEXCR, the
equivalent register for the ultravisor state (not implemented).
Signed-off-by: Nicholas Miehlbradt <nicholas@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221220042330.2387944-2-nicholas@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Let's not leave developers in the dark where this log message comes
from.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216145709.271940-2-shentey@gmail.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
kvm_ppc.h is missing various declarations from "cpu.h":
target/ppc/kvm_ppc.h:128:40: error: unknown type name 'CPUPPCState'; did you mean 'CPUState'?
static inline int kvmppc_get_hypercall(CPUPPCState *env,
^~~~~~~~~~~
CPUState
include/qemu/typedefs.h:45:25: note: 'CPUState' declared here
typedef struct CPUState CPUState;
^
target/ppc/kvm_ppc.h:134:40: error: unknown type name 'PowerPCCPU'
static inline int kvmppc_set_interrupt(PowerPCCPU *cpu, int irq, int level)
^
target/ppc/kvm_ppc.h:285:38: error: unknown type name 'hwaddr'
hwaddr ptex, int n)
^
target/ppc/kvm_ppc.h:220:15: error: unknown type name 'target_ulong'
static inline target_ulong kvmppc_configure_v3_mmu(PowerPCCPU *cpu,
^
target/ppc/kvm_ppc.h:286:38: error: unknown type name 'ppc_hash_pte64_t'
static inline void kvmppc_read_hptes(ppc_hash_pte64_t *hptes,
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221213123550.39302-2-philmd@linaro.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Convert the ppc CPU class to use 3-phase reset, so it doesn't
need to use device_class_set_parent_reset() any more.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-id: 20221124115023.2437291-14-peter.maydell@linaro.org
Kowshik reported that building qemu with GCC 12.2.1 for 'ppc64-softmmu'
target is failing due to following build warnings:
<snip>
../target/ppc/cpu_init.c:7018:13: error: 'ppc_restore_state_to_opc' defined but not used [-Werror=unused-function]
7018 | static void ppc_restore_state_to_opc(CPUState *cs,
<snip>
Fix this by wrapping these function definitions in 'ifdef CONFIG_TCG' so that
they are only defined if qemu is compiled with '--enable-tcg'
Reported-by: Kowshik Jois B S <kowsjois@linux.ibm.com>
Fixes: 61bd1d2942 ("target/ppc: Convert to tcg_ops restore_state_to_opc")
Fixes: 670f1da374 ("target/ppc: Implement hashst and hashchk")
Fixes: 53ae2aeb94 ("target/ppc: Implement hashstp and hashchkp")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1319
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Kowshik Jois B S <kowsjois@linux.vnet.ibm.com>
Message-Id: <20221116131743.658708-1-vaibhav@linux.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The value passed is always true, and if the target's
synchronize_from_tb hook is non-trivial, not exiting
may be erroneous.
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Commit 47e83d9107 ended up unintentionally changing the control flow
of ppc_radix64_process_scoped_xlate(). When guest_visible is false,
it must not raise an exception, even if the radix configuration is
not valid.
This regression prevented Linux boot in a nested environment with
L1 using TCG and emulating KVM (cap-nested-hv=on) and L2 using
KVM. L2 would hang on Linux's futex_init(), when it tested how a
futex_atomic_cmpxchg_inatomic() handled a fault, because L1 would
start a loop of trying to perform partition scoped translations
and raising exceptions.
Fixes: 47e83d9107 ("target/ppc: Improve Radix xlate level validation")
Reported-by: Victor Colombo <victor.colombo@eldorado.org.br>
Signed-off-by: Leandro Lupori <leandro.lupori@eldorado.org.br>
Tested-by: Víctor Colombo <victor.colombo@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221028183617.121786-1-leandro.lupori@eldorado.org.br>
[danielhb: use %"PRIu64" to print 'nls']
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Profiling QEMU during Fedora 35 for PPC64 boot revealed that
6.39% of total time was being spent in helper_insns_inc(), on a
POWER9 machine. To avoid calling this helper every time PMCs had
to be incremented, an inline implementation of PMC5 increment and
check for overflow was developed. This led to a reduction of
about 12% in Fedora's boot time.
Signed-off-by: Leandro Lupori <leandro.lupori@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221025202424.195984-4-leandro.lupori@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Add 2 new PMC related HFLAGS:
- HFLAGS_PMCJCE - value of MMCR0 PMCjCE bit
- HFLAGS_PMC_OTHER - set if a PMC other than PMC5-6 is enabled
These flags allow further optimization of PMC5 update code, by
allowing frequently tested conditions to be performed at
translation time.
Signed-off-by: Leandro Lupori <leandro.lupori@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221025202424.195984-3-leandro.lupori@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Move the methods to excp_helper.c and make them static.
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20221021142156.4134411-4-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Now that cs->interrupt_request indicates if there is any unmasked
interrupt, checking if the CPU has work to do can be simplified to a
single check that works for all CPU models.
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20221021142156.4134411-3-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
This new method will check if any pending interrupt was unmasked and
then call cpu_interrupt/cpu_reset_interrupt accordingly. Code that
raises/lowers or masks/unmasks interrupts should call this method to
keep CPU_INTERRUPT_HARD coherent with env->pending_interrupts.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20221021142156.4134411-2-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Export p7_interrupt_powersave and use it in p7_next_unmasked_interrupt.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-26-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Move the interrupt masking logic out of cpu_has_work_POWER7 in a new
method, p7_interrupt_powersave, that only returns an interrupt if it can
wake the processor from power-saving mode.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-25-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Remove the following unused interrupts from the POWER7 interrupt
processing method:
- PPC_INTERRUPT_RESET: only raised for 6xx, 7xx, 970 and POWER5p;
- Hypervisor Virtualization: introduced in Power ISA v3.0;
- Hypervisor Doorbell and Event-Based Branch: introduced in
Power ISA v2.07;
- Critical Input, Watchdog Timer, and Fixed Interval Timer: only defined
for embedded CPUs;
- Doorbell and Critical Doorbell Interrupt: processor does not implement
the Embedded.Processor Control category;
- Programmable Interval Timer: 40x-only;
- PPC_INTERRUPT_THERM: only raised for 970 and POWER5p;
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-23-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The new method is identical to ppc_deliver_interrupt, processor-specific
code will be added/removed in the following patches.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-22-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Remove the following unused interrupts from the POWER7 interrupt masking
method:
- PPC_INTERRUPT_RESET: only raised for 6xx, 7xx, 970 and POWER5p;
- Hypervisor Virtualization: introduced in Power ISA v3.0;
- Hypervisor Doorbell and Event-Based Branch: introduced in
Power ISA v2.07;
- Critical Input, Watchdog Timer, and Fixed Interval Timer: only defined
for embedded CPUs;
- Doorbell and Critical Doorbell Interrupt: processor does not implement
the Embedded.Processor Control category;
- Programmable Interval Timer: 40x-only;
- PPC_INTERRUPT_THERM: only raised for 970 and POWER5p;
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-21-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The new method is identical to ppc_next_unmasked_interrupt_generic,
processor-specific code will be added/removed in the following patches.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-20-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Export p8_interrupt_powersave and use it in p8_next_unmasked_interrupt.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-19-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Move the interrupt masking logic out of cpu_has_work_POWER8 in a new
method, p8_interrupt_powersave, that only returns an interrupt if it can
wake the processor from power-saving mode.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-18-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Remove the following unused interrupts from the POWER8 interrupt
processing method:
- PPC_INTERRUPT_RESET: only raised for 6xx, 7xx, 970 and POWER5p;
- Debug Interrupt: removed in Power ISA v2.07;
- Hypervisor Virtualization: introduced in Power ISA v3.0;
- Critical Input, Watchdog Timer, and Fixed Interval Timer: only defined
for embedded CPUs;
- Critical Doorbell: processor does not implement the
"Embedded.Processor Control" category;
- Programmable Interval Timer: 40x-only;
- PPC_INTERRUPT_THERM: only raised for 970 and POWER5p;
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-16-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The new method is identical to ppc_deliver_interrupt, processor-specific
code will be added/removed in the following patches.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-15-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Remove the following unused interrupts from the POWER8 interrupt masking
method:
- PPC_INTERRUPT_RESET: only raised for 6xx, 7xx, 970, and POWER5p;
- Debug Interrupt: removed in Power ISA v2.07;
- Hypervisor Virtualization: introduced in Power ISA v3.0;
- Critical Input, Watchdog Timer, and Fixed Interval Timer: only defined
for embedded CPUs;
- Critical Doorbell: processor does not implement the "Embedded.Processor
Control" category;
- Programmable Interval Timer: 40x-only;
- PPC_INTERRUPT_THERM: only raised for 970 and POWER5p;
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-14-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
The new method is identical to ppc_next_unmasked_interrupt_generic,
processor-specific code will be added/removed in the following patches.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-13-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Export p9_interrupt_powersave and use it in p9_next_unmasked_interrupt.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-12-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Move the interrupt masking logic out of cpu_has_work_POWER9 in a new
method, p9_interrupt_powersave, that only returns an interrupt if it can
wake the processor from power-saving mode.
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Message-Id: <20221011204829.1641124-11-matheus.ferst@eldorado.org.br>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
