qemu_smbios_type8_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: fd8caa253c ("hw/smbios: support for type 8 (port connector)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <20240129-smbios-v2-2-9ee6fede0d10@daynix.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qemu_smbios_type11_opts did not have the list terminator and that
resulted in out-of-bound memory access. It also needs to have an element
for the type option.
Cc: qemu-stable@nongnu.org
Fixes: 2d6dcbf93f ("smbios: support setting OEM strings table")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-Id: <20240129-smbios-v2-1-9ee6fede0d10@daynix.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virgl_renderer_resource_get_info() returns errno and not -1 on error.
Correct the return-value check.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Message-Id: <20240129073921.446869-1-dmitry.osipenko@collabora.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previously not all references mentioned any spec version at all.
Given r3.1 is the current specification available for evaluation at
www.computeexpresslink.org update references to refer to that.
Hopefully this won't become a never ending job.
A few structure definitions have been updated to add new fields.
Defaults of 0 and read only are valid choices for these new DVSEC
registers so go with that for now.
There are additional error codes and some of the 'questions' in
the comments are resolved now.
Update documentation reference to point to the CXL r3.1 specification
with naming closer to what is on the cover.
For cases where there are structure version numbers, add defines
so they can be found next to the register definitions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst the reported version was 1 so there should be no changes,
a couple of fields (where the value 0 was valid) were not
defined. Make those explicit and update references to be based
on CXL r3.1.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Part of bringing all of CXL emulation inline with CXL r3.1.
No functional changes.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Not actually implemented, but we need to reserve more space for
the larger version of the structure in CXL r3.1.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Part of standardizing the QEMU code on CXL r3.1.
No fuctional changes as everything added is optional and
it is set as not implemented.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126121636.24611-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
_STA will now return 0xB (in common with most other devices)
rather than not setting the bits to indicate this fake device
has not been enabled, and self tests haven't passed.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-13-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Found whilst testing a series for the linux kernel that actually
bothers to check if enabled is set. 0xB is the option used
for vast majority of DSDT entries in QEMU.
It is a little odd for a device that doesn't really exist and
is simply a hook to tell the OS there is a CEDT table but 0xB
seems a reasonable choice and avoids need to special case
this device in the OS.
Means:
* Device present.
* Device enabled and decoding it's resources.
* Not shown in UI
* Functioning properly
* No battery (on this device!)
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-12-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The _STA value returned currently indicates the ACPI0017 device
is not enabled. Whilst this isn't a real device, setting _STA
like this may prevent an OS from enumerating it correctly and
hence from parsing the CEDT table.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-11-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes Coverity ID 1522368.
Currently error_fatal is set if interleave_ways_dec() is going to return 0
but we should handle that zero return explicitly.
Reported-by: Stefan Hajnoczi <stefanha@gmail.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-10-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
a NULL parameter is enough for a NULL MemoryRegionOps
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cache_mem_ops.{read,write}() interprets opaque as
CXLComponentState(cxl_cstate) instead of ComponentRegisters(cregs).
Fortunately, cregs is the first member of cxl_cstate, so their values are
the same.
Fixes: 9e58f52d3f ("hw/cxl/component: Introduce CXL components (8.1.x, 8.2.5)")
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Li Zhijian <lizhijian@fujitsu.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the current mdev_reg_read() implementation, it consistently returns
that the Media Status is Ready (01b). This was fine until commit
25a52959f9 ("hw/cxl: Add support for device sanitation") because the
media was presumed to be ready.
However, as per the CXL 3.0 spec "8.2.9.8.5.1 Sanitize (Opcode 4400h)",
during sanitation, the Media State should be set to Disabled (11b). The
mentioned commit correctly sets it to Disabled, but mdev_reg_read()
still returns Media Status as Ready.
To address this, update mdev_reg_read() to read register values instead
of returning dummy values.
Note that __toggle_media() managed to not only write something
that no one read, it did it to the wrong register storage and
so changed the reported mailbox size which was definitely not
the intent. That gets fixed as a side effect of allocating
separate state storage for this register.
Fixes: commit 25a52959f9 ("hw/cxl: Add support for device sanitation")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Two functions were reported to have dead code, remove the bogus
branches altogether, as well as a misplaced qemu_log call.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The addition of the DCD support for CXL type-3 devices extended the CDAT
table large enough that the checksum being returned was incorrect.[1]
This was because the checksum value was using the header length field
rather than each of the 4 bytes of the length field. This was
previously not seen because the length of the CDAT data was less than
256 thus resulting in an equivalent checksum value.
Properly calculate the checksum for the CDAT header.
[1] https://lore.kernel.org/all/20231116-fix-cdat-devm-free-v1-1-b148b40707d7@intel.com/
Fixes: aba578bdac ("hw/cxl/cdat: CXL CDAT Data Object Exchange implementation")
Cc: Huai-Cheng Kuo <hchkuo@avery-design.com.tw>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As a failure of g_malloc() will result in QEMU exiting, it
won't return a NULL to check. As such, drop the incorrect handling
of such NULL returns in the cdat table building code.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As g_malloc0/g_malloc() will just exit QEMU on failure there is no
point in checking for it failing.
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callback for building CDAT tables may return negative error codes.
This was previously unhandled and will result in potentially huge
allocations later on in ct3_build_cdat()
Detect the negative error code and defer cdat building.
Fixes: f5ee7413d5 ("hw/mem/cxl-type3: Add CXL CDAT Data Object Exchange")
Cc: Huai-Cheng Kuo <hchkuo@avery-design.com.tw>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
s->smmu_pcibus_by_bus_num is a SMMUPciBus pointer cache indexed
by bus number, bus number may not always be a fixed value,
i.e., guest reboot to different kernel which set bus number with
different algorithm.
This could lead to smmu_iommu_mr() providing the wrong iommu MR.
Suggested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240125073706.339369-3-zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
s->iommu_pcibus_by_bus_num is a IOMMUPciBus pointer cache indexed
by bus number, bus number may not always be a fixed value,
i.e., guest reboot to different kernel which set bus number with
different algorithm.
This could lead to endpoint binding to wrong iommu MR in
virtio_iommu_get_endpoint(), then vfio device setup wrong
mapping from other device.
Remove the memset in virtio_iommu_device_realize() to avoid
redundancy with memset in system reset.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20240125073706.339369-2-zhenzhong.duan@intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Due to my own limitation on bandwidth, I noticed that unfortunately I won't
have time to review VT-d patches at least in the near future. Meanwhile I
expect a lot of possibilities could actually happen in this area in the
near future.
To reflect that reality, I decided to drop myself from the VT-d role. It
shouldn't affect much since we still have Jason around like usual, and
Michael on top. But I assume it'll always be good if anyone would like to
fill this role up.
I'll still work on QEMU. So I suppose anyone can still copy me if one
thinks essential.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20240118091035.48178-1-peterx@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Jason Wang <jasowang@redhat.com>
There is no "size" field in vring address structure. Remove it.
Fixes: 5fc0e00291 ("Add vhost-user protocol documentation")
Signed-off-by: Andrey Ignatov <rdna@apple.com>
Message-Id: <20240112004555.64900-1-rdna@apple.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The VIA south bridges are able to relocate and toggle (enable or disable) their
SuperI/O functions. So far this is hardcoded such that all functions are always
enabled and are located at fixed addresses.
Some PC BIOSes seem to probe for I/O occupancy before activating such a function
and issue an error in case of a conflict. Since the functions are currently
enabled on reset, conflicts are always detected. Prevent that by implementing
relocation and toggling of the SuperI/O functions.
Note that all SuperI/O functions are now deactivated upon reset (except for
VT82C686B's serial ports where Fuloong 2e's rescue-yl seems to expect them to be
enabled by default). Rely on firmware to configure the functions accordingly.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-12-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is a preparation for implementing relocation and toggling of SuperI/O
functions in the VT8231 device model. Upon reset, all SuperI/O functions will be
deactivated, so in case if no -bios is given, let the machine configure those
functions the same way Pegasos II firmware would do.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-11-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The real SuperI/O chips emulated by QEMU allow for relocating and enabling or
disabling their SuperI/O functions via software. So far this is not implemented.
Prepare for that by adding isa_parallel_set_{enabled,iobase}.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-10-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The real SuperI/O chips emulated by QEMU allow for relocating and enabling or
disabling their SuperI/O functions via software. So far this is not implemented.
Prepare for that by adding isa_serial_set_{enabled,iobase}.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-9-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The real SuperI/O chips emulated by QEMU allow for relocating and enabling or
disabling their SuperI/O functions via software. So far this is not implemented.
Prepare for that by adding isa_fdc_set_{enabled,iobase}.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some SuperI/O devices such as the VIA south bridges or the PC87312 controller
allow to enable or disable their SuperI/O functions. Add a convenience function
for implementing this in the VIA south bridges.
The naming of the functions is inspired by its memory_region_set_enabled()
pendant.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some SuperI/O devices such as the VIA south bridges or the PC87312 controller
are able to relocate their SuperI/O functions. Add a convenience function for
implementing this in the VIA south bridges.
This convenience function relies on previous simplifications in exec/ioport
which avoids some duplicate synchronization of I/O port base addresses. The
naming of the function is inspired by its memory_region_set_address() pendant.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
portio_list_add_1() creates a MemoryRegionPortioList instance which holds a
MemoryRegion `mr` and an array of MemoryRegionPortio elements named `ports`.
Each element in the array gets assigned the same value for its .base attribute.
The same value also ends up as the .addr attribute of `mr` due to the
memory_region_add_subregion() call. This means that all .base attributes are
the same as `mr.addr`.
The only usages of MemoryRegionPortio::base were in portio_read() and
portio_write(). Both functions get above MemoryRegionPortioList as their
opaque parameter. In both cases find_portio() can only return one of the
MemoryRegionPortio elements of the `ports` array. Due to above observation any
element will have the same .base value equal to `mr.addr` which is also
accessible.
Hence, `mrpio->mr.addr` is equivalent to `mrp->base` and
MemoryRegionPortio::base is redundant and can be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240114123911.4877-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ParallelState::portio_list isn't used inside ParallelState context but only
inside ISAParallelState context, so move it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
FDCtrl::iomem isn't used inside FDCtrl context but only inside FDCtrlSysBus
context, so move it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
FDCtrl::portio_list isn't used inside FDCtrl context but only inside
FDCtrlISABus context, so move it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20240114123911.4877-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240106132546.21248-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU populates the apic_state attribute of x86 CPUs if supported by real
hardware or if SMP is active. When handling interrupts, it just checks whether
apic_state is populated to route the interrupt to the PIC or to the APIC.
However, chapter 10.4.3 of [1] requires that:
When IA32_APIC_BASE[11] is 0, the processor is functionally equivalent to an
IA-32 processor without an on-chip APIC.
This means that when apic_state is populated, QEMU needs to check for the
MSR_IA32_APICBASE_ENABLE flag in addition. Implement this which fixes some
real-world BIOSes.
[1] Intel 64 and IA-32 Architectures Software Developer's Manual, Vol. 3A:
System Programming Guide, Part 1
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240106132546.21248-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The if statement currently uses double negation when executing the else branch.
So swap the branches and simplify the condition to make the code more
comprehensible.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20240106132546.21248-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds XTSup configuration to let user choose to whether enable
this feature or not. When XTSup is enabled, additional bytes in IRTE with
enabled guest virtual VAPIC are used to support 32-bit destination id.
Additionally, this commit exports IVHD type 0x11 besides the old IVHD type
0x10 in ACPI table. IVHD type 0x10 does not report full set of IOMMU
features only the legacy ones, so operating system (e.g. Linux) may only
detects x2APIC support if IVHD type 0x11 is available. The IVHD type 0x10
is kept so that old operating system that only parses type 0x10 can detect
the IOMMU device.
Besides, an amd_iommu-stub.c file is created to provide the definition for
amdvi_extended_feature_register when CONFIG_AMD_IOMMU=n. This function is
used by acpi-build.c to get the extended feature register value for
building the ACPI table. When CONFIG_AMD_IOMMU=y, this function is defined
in amd_iommu.c.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-7-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Following the instructions in bios-tables-test, this lists that IVRS.ivrs
in ACPI table will be changed to add new IVHD type 0x11.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-6-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As userspace APIC now supports x2APIC, intel interrupt remapping
hardware can be set to EIM mode when userspace local APIC is used.
Suggested-by: Joao Martins <joao.m.martins@oracle.com>
Acked-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-5-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit adds support for x2APIC transitions when writing to
MSR_IA32_APICBASE register and finally adds CPUID_EXT_X2APIC to
TCG_EXT_FEATURES.
The set_base in APICCommonClass now returns an integer to indicate error in
execution. apic_set_base return -1 on invalid APIC state transition,
accelerator can use this to raise appropriate exception.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-4-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit extends the APIC ID to 32-bit long and remove the 255 max APIC
ID limit in userspace APIC. The array that manages local APICs is now
dynamically allocated based on the max APIC ID of created x86 machine.
Also, new x2APIC IPI destination determination scheme, self IPI and x2APIC
mode register access are supported.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-3-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This commit creates apic_register_read/write which are used by both
apic_mem_read/write for MMIO access and apic_msr_read/write for MSR access.
The apic_msr_read/write returns -1 on error, accelerator can use this to
raise the appropriate exception.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Message-Id: <20240111154404.5333-2-minhquangbui99@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch derives vhost-user-input from vhost-user-base class, so make
the input stub as a simpler boilerplate wrapper.
With the refactoring, vhost-user-input adds the property 'chardev', this
leads to conflict with the vhost-user-input-pci adds the same property.
To resolve the error, remove the duplicate property from
vhost-user-input-pci.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20231120043721.50555-5-leo.yan@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-12-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user-input is in the input folder. On the other hand, the folder
'hw/virtio' maintains other virtio stubs (e.g. I2C, RNG, GPIO, etc).
This patch moves vhost-user-input into the virtio folder for better code
organization. No functionality change.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-Id: <20231120043721.50555-4-leo.yan@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-11-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds basic documentation for vhost-user-input.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Message-Id: <20231120043721.50555-3-leo.yan@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-10-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Virtio input device invokes set_config() callback for retrieving
the event configuration info, but the callback is not supported in
vhost-user-base.
This patch adds support set_config() callback in vhost-user-base.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20231120043721.50555-2-leo.yan@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-9-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make it clear the vhost-user-device is intended for expert use only.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240104210945.1223134-8-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
