with max-bytes set to 0, quota is 0 and so device does not work.
block this to avoid user confusion
Message-Id: <73a89a42d82ec8b47358f25119b87063e4a6ea57.1721818306.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
In bcm2835_property_mbox_push(), some variables are defined at function scope
but used only in a smaller scope of the function:
* tag, bufsize, resplen are used only in the body of the while() loop
* tmp is used only for RPI_FWREQ_SET_POWER_STATE (and is badly named)
Declare these variables in the scope where they're needed, so the code
is easier to read.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240723131029.1159908-5-peter.maydell@linaro.org
In the long function bcm2835_property_mbox_push(), the variables
start_num, number and otp_row are used only in the four cases which
access OTP data, and their uses don't overlap with each other.
Make these variables have scope restricted to the cases where they're
used, so it's easier to read each individual case without having to
cross-refer up to the variable declaration at the top of the function
and check whether the variable is also used later in the loop.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240723131029.1159908-4-peter.maydell@linaro.org
Coverity points out that in our handling of the property
RPI_FWREQ_SET_CUSTOMER_OTP we have a potential overflow. This
happens because we read start_num and number from the guest as
unsigned 32 bit integers, but then the variable 'n' we use as a loop
counter as we iterate from start_num to start_num + number is only an
"int". That means that if the guest passes us a very large start_num
we will interpret it as negative. This will result in an assertion
failure inside bcm2835_otp_set_row(), which checks that we didn't
pass it an invalid row number.
A similar issue applies to all the properties for accessing OTP rows
where we are iterating through with a start and length read from the
guest.
Use uint32_t for the loop counter to avoid this problem. Because in
all cases 'n' is only used as a loop counter, we can do this as
part of the for(), restricting its scope to exactly where we need it.
Resolves: Coverity CID 1549401
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240723131029.1159908-3-peter.maydell@linaro.org
The documentation of the "Set palette" mailbox property at
https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface#set-palette
says it has the form:
Length: 24..1032
Value:
u32: offset: first palette index to set (0-255)
u32: length: number of palette entries to set (1-256)
u32...: RGBA palette values (offset to offset+length-1)
We get this wrong in a couple of ways:
* we aren't checking the offset and length are in range, so the guest
can make us spin for a long time by providing a large length
* the bounds check on our loop is wrong: we should iterate through
'length' palette entries, not 'length - offset' entries
Fix the loop to implement the bounds checks and get the loop
condition right. In the process, make the variables local to
this switch case, rather than function-global, so it's clearer
what type they are when reading the code.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240723131029.1159908-2-peter.maydell@linaro.org
Coverity has spotted a possible problem with the OAS handling
(CID 1558464), where the error return of oas2bits() -1 is not
checked, which can cause an overflow in oas value.
oas2bits() is only called with valid inputs, harden the function
to assert that.
Reported-By: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20240722103531.2377348-1-smostafa@google.com
Link: https://lore.kernel.org/qemu-devel/CAFEAcA-H=n-3mHC+eL6YjfL1m+x+b+Fk3mkgZbN74WNxifFVow@mail.gmail.com/
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When a bare-metal application on the raspi3 board reads the
AUX_MU_STAT_REG MMIO register while the device's buffer is
at full receive FIFO capacity
(i.e. `s->read_count == BCM2835_AUX_RX_FIFO_LEN`) the
assertion `assert(s->read_count < BCM2835_AUX_RX_FIFO_LEN)`
fails.
Reported-by: Cryptjar <cryptjar@junk.studio>
Suggested-by: Cryptjar <cryptjar@junk.studio>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/459
Signed-off-by: Frederik van Hövell <frederik@fvhovell.nl>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMM: commit message tweaks]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ppc_hash64_hpt_base() and ppc_hash64_hpt_mask() functions are
mostly used by mmu-hash64.c only but there is one call to
ppc_hash64_hpt_mask() in hw/ppc/spapr_vhyp_mmu.c.in a helper function
that can be moved to mmu-hash64.c which allows these functions to be
removed from the header.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Additional END state 'info pic' information as added. The 'ignore',
'crowd' and 'precluded escalation control' bits of an Event Notification
Descriptor are all used when delivering an interrupt targeting a VP-group
or crowd.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
In XIVE Gen 2 there were some minor changes to the TIMA header that were
updated when printed.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Moving xive2_nvp_pic_print_info() to align with the other "pic_print_info"
functions.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Fail VST entry address computation if firmware doesn't define a descriptor
for one of the Virtualization Structure Tables (VST), there's no point in
trying to compute the address of its entry. Abort the operation and log
an error.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Set Translation Table for the NVC port space is missing. The xive model
doesn't take into account the remapping of IO operations via the Set
Translation Table but firmware is allowed to define it for the Notify
Virtual Crowd (NVC), like it's already done for the other VST tables.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Enable NVG and NVC VST tables for index compression which indicates the number
of bits the address is shifted to the right for the table accesses.
The compression values are defined as:
0000 - No compression
0001 - 1 bit shift
0010 - 2 bit shift
....
1000 - 8 bit shift
1001-1111 - No compression
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Both the virtualization layer (VC) and presentation layer (PC) need to
be configured to access the VSTs. Since the information is redundant,
the xive model combines both into one set of tables and only the
definitions going through the VC are kept. The definitions through the
PC are ignored. That works well as long as firmware calls the VC for
all the tables.
For the NVG and NVC tables, it can make sense to only configure them
with the PC, since they are only used by the presenter. So this patch
allows firmware to configure the VST tables through the PC as well.
The definitions are still shared, since the VST tables can be set
through both the VC and/or PC, they are dynamically re-mapped in
memory by first deleting the memory subregion.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The cache watch facility uses the same register interface to handle
entries in the NVP, NVG and NVC tables. A bit-field in the 'watchX
specification' register tells the table type. So far, that bit-field
was not read and the code assumed a read/write to the NVP table.
This patch allows to read/write entries in the NVG and NVC table as
well.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Adds support for writing a completion notification byte in memory
whenever a cache flush or queue sync inject operation is requested by
software. QEMU does not cache any of the XIVE data that is in memory and
therefore it simply writes the completion notification byte at the time
that the operation is requested.
Co-authored-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Made changes to some structure and define elements to ease review in
next patchset.
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
XIVE offers a 'cache watch facility', which allows software to read/update
a potentially cached table entry with no software lock. There's one such
facility in the Virtualization Controller (VC) to update the ESB and END
entries and one in the Presentation Controller (PC) to update the
NVP/NVG/NVC entries.
Each facility has 4 cache watch engines to control the updates and
firmware can request an available engine by querying the hardware
'watch_assign' register of the VC or PC. The engine is then reserved and
is released after the data is updated by reading the 'watch_spec' register
(which also allows to check for a conflict during the update).
If no engine is available, the special value 0xFF is returned and
firmware is expected to repeat the request until an engine becomes
available.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Kowal <kowal@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Add Microchip's 25CSM04 Serial EEPROM to m25p80. 25CSM04 provides 4 Mbits
of Serial EEPROM utilizing the Serial Peripheral Interface (SPI) compatible
bus. The device is organized as 524288 bytes of 8 bits each (512Kbyte) and
is optimized for use in consumer and industrial applications where reliable
and dependable nonvolatile memory storage is essential.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
In this commit SPI shift engine and sequencer logic is implemented.
Shift engine performs serialization and de-serialization according to the
control by the sequencer and according to the setup defined in the
configuration registers. Sequencer implements the main control logic and
FSM to handle data transmit and data receive control of the shift engine.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
SPI controller device model supports a connection to a single SPI responder.
This provide access to SPI seeproms, TPM, flash device and an ADC controller.
All SPI function control is mapped into the SPI register space to enable full
control by firmware. In this commit SPI configuration component is modelled
which contains all SPI configuration and status registers as well as the hold
registers for data to be sent or having been received.
An existing QEMU SSI framework is used and SSI_BUS is created.
Signed-off-by: Chalapathi V <chalapathi.v@linux.ibm.com>
Reviewed-by: Caleb Schlossin <calebs@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
[np: Fix FDT macro compile for qtest]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Recent POWER CPUs can operate in "LPAR per core" or "LPAR per thread"
modes. In per-core mode, some SPRs and IPI doorbells are shared between
threads in a core. In per-thread mode, supervisor and user state is
not shared between threads.
OpenPOWER systems after POWER8 use LPAR per thread mode, and it is
required for KVM. Enterprise systems use LPAR per core mode, as they
partition the machine by core.
Implement a lpar-per-core machine option for powernv machines. This
is fixed true for POWER8 machines, and defaults off for P9 and P10.
With this change, powernv8 SMT now works sufficiently to run Linux,
with a single socket. Multi-threaded KVM guests still have problems,
as does multi-socket Linux boot.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The PC unit in the processor core contains xscom registers that provide
low level status and control of the CPU.
This implements "direct controls", sufficient for skiboot firmware,
which uses it to send NMI IPIs between CPUs.
POWER10 is sufficiently different from POWER9 (particularly with respect
to QME and special wakeup) that it is not trivial to implement POWER9
support by reusing the code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power CPUs have an execution control facility that can pause, resume,
and cause NMIs, among other things. Add a function that will nmi a CPU
and resume it if it was paused, in preparation for implementing the
control facility.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Big-core implementation is complete, so expose it as a machine
property that may be set with big-core=on option on powernv9 and
powernv10 machines.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER10 has a quirk in its ChipTOD addressing that requires the even
small-core to be selected even when programming the odd small-core.
This allows skiboot chiptod init to run in big-core mode.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power9/10 CPUs have PVR[51] set in small-core mode and clear in big-core
mode. This is used by skiboot firmware.
PVR is not hypervisor-privileged but it is not so important that spapr
to implement this because it's generally masked out of PVR matching code
in kernels, and only used by firmware.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
device-tree building needs to account for big-core mode, because it is
driven by qemu cores (small cores). Every second core should be skipped,
and every core should describe threads for both small-cores that make
up the big core.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
POWER9 and POWER10 machines come in two variants, big-core and
small-core. Big-core machines are SMT8 from software's point of view,
but the low level platform topology ("xscom registers and pervasive
addressing"), these look more like a pair of small cores ganged
together.
Presently the way this is modelled is to create one SMT8 PnvCore and add
special cases to xscom and pervasive for big-core mode that tries to
split this into two small cores, but this is becoming too complicated to
manage.
A better approach is to create 2 core structures and ganging them
together to look like an SMT8 core in TCG. Then the xscom and pervasive
models mostly do not need to differentiate big and small core modes.
This change adds initial mode bits and QEMU topology handling to
split SMT8 cores into 2xSMT4 cores.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The decision to branch out to a slower SMT path in instruction
emulation will become a bit more complicated with the way that
"big-core" topology that will be implemented in subsequent changes.
Hide these details from the wider CPU emulation code with a bool
has_smt_siblings flag that can be set by machine initialisation.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The way SMT thread siblings are matched is clunky, using hard-coded
logic that checks the PIR SPR.
Change that to use a new core_index variable in the CPUPPCState,
where all siblings have the same core_index. CPU realize routines have
flexibility in setting core/sibling topology.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The chip_pir chip class method allows the platform to set the PIR
processor identification register. Extend this to a more general
ID function which also allows the TIR to be set. This is in
preparation for "big core", which is a more complicated topology
of cores and threads.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Use a class attribute to specify the number of SMT threads per core
permitted for different machines, 8 for powernv8 and 4 for powernv9/10.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The timebase state machine is per per-core state and can be driven
by any thread in the core. It is currently implemented as a hack
where the state is in a CPU structure and only thread 0's state is
accessed by the chiptod, which limits programming the timebase
side of the state machine to thread 0 of a core.
Move the state out into PnvCore and share it among all threads.
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This helps move core state from CPU to core structures.
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
One of the functions of the ADU is indirect memory access engines that
send and receive data via ADU registers.
This implements the ADU LPC memory access functionality sufficiently
for IBM proprietary firmware to access the UART and print characters
to the serial port as it does on real hardware.
This requires a linkage between adu and lpc, which allows adu to
perform memory access in the lpc space.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This implements a framework for an ADU unit model.
The ADU unit actually implements XSCOM, which is the bridge between MMIO
and PIB. However it also includes control and status registers and other
functions that are exposed as PIB (xscom) registers.
To keep things simple, pnv_xscom.c remains the XSCOM bridge
implementation, and pnv_adu.c implements the ADU registers and other
functions.
So far, just the ADU no-op registers in the pnv_xscom.c default handler
are moved over to the adu model.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The POWER8 LPC ISA device irqs all get combined and reported to the line
connected the PSI LPCHC irq. POWER9 changed this so only internal LPC
host controller irqs use that line, and the device irqs get routed to
4 new lines connected to PSI SERIRQ0-3.
POWER9 also introduced a new feature that automatically clears the irq
status in the LPC host controller when EOI'ed, so software does not have
to.
The powernv OPAL (skiboot) firmware managed to work because the LPCHC
irq handler scanned all LPC irqs and handled those including clearing
status even on POWER9 systems. So LPC irqs worked despite OPAL thinking
it was running in POWER9 mode. After this change, UART interrupts show
up on serirq1 which is where OPAL routes them to:
cat /proc/interrupts
...
20: 0 XIVE-IRQ 1048563 Level opal-psi#0:lpchc
...
25: 34 XIVE-IRQ 1048568 Level opal-psi#0:lpc_serirq_mux1
Whereas they previously turn up on lpchc.
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The LPC HC irq status register bits are set when an LPC IRQSER input is
asserted. These irq status bits drive the PSI irq to the CPU interrupt
controller. The LPC HC irq status bits are cleared by software writing
to the register with 1's for the bits to clear.
Existing register write was clearing the irq status bits even when the
input was asserted, this results in interrupts being lost.
This fix changes the behavior to keep track of the device IRQ status
in internal state that is separate from the irq status register, and
only allowing the irq status bits to be cleared if the associated
input is not asserted.
Signed-off-by: Glenn Miles <milesg@linux.ibm.com>
[np: rebased before P9 PSI SERIRQ patch, adjust changelog/comments]
Reviewed-by: Glenn Miles <milesg@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Power10 DD1.0 was dropped in:
commit 8f054d9ee8 ("ppc: Drop support for POWER9 and POWER10 DD1 chips")
Use the newer Power10 DD2 chips cfam id.
Signed-off-by: Aditya Gupta <adityag@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
FDT properties are aligned by 4 bytes, not 8 bytes.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This fixes LeakSanitizer warnings.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
This cap did not add the migration code when it was introduced. This
results in migration failure when changing the default using the
command line.
Cc: qemu-stable@nongnu.org
Fixes: ccc5a4c5e1 ("spapr: Add SPAPR_CAP_AIL_MODE_3 for AIL mode 3 support for H_SET_MODE hcall")
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
