This determines whether the Apple Sound Chip (ASC) is set to enhanced mode
(default) or to original mode. The real Q800 hardware used an EASC chip however
a lot of older software only works with the older ASC chip.
Adding this as a machine parameter allows QEMU to be used as an developer aid
for testing and migrating code from ASC to EASC.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The Quadra 800 has the enhanced ASC (EASC) audio chip which supports both the
legacy IRQ routing through VIA2 and also "A/UX" mode routing direct to the
CPU.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231004083806.757242-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS attempts a series of writes and reads over the entire RAM area in order
to determine the amount of RAM within the machine. Allow accesses to the
entire RAM area ignoring writes and always reading zero for areas where there
is no physical RAM installed to allow MacOS to detect the memory size without
faulting.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It is needed because it defines the BIOSConfig area.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20231004083806.757242-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
MacOS reads this address to identify the hardware.
This is a basic implementation returning the ID of Quadra 800.
Details:
http://mess.redump.net/mess/driver_info/mac_technical_notes
"There are 3 ID schemes [...]
The third and most scalable is a machine ID register at 0x5ffffffc.
The top word must be 0xa55a to be valid. Then bits 15-11 are 0 for
consumer Macs, 1 for portables, 2 for high-end 68k, and 3 for high-end
PowerPC. Bit 10 is 1 if additional ID bits appear elsewhere (e.g. in VIA1).
The rest of the bits are a per-model identifier.
Model Lower 16 bits of ID
...
Quadra/Centris 610/650/800 0x2BAD"
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The djMEMC controller is used to store information related to the physical memory
configuration.
Co-developed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20231004083806.757242-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the macfb device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-23-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Instead use the qdev_get_child_bus() function which is intended for this exact
purpose.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-22-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the mac-nubus-bridge device to use
object_initialize_child() and map the Nubus address space using
memory_region_add_subregion() instead of sysbus_mmio_map().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the SWIM device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the ESP device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the escc_orgate device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the ESCC device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the dp8393x device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the VIA2 device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the VIA1 device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The current use of aliased memory regions causes us 2 problems: firstly the
output of "info qom-tree" is absolutely huge and difficult to read, and
secondly we have already reached the internal limit for memory regions as
adding any new memory region into the mac-io region causes QEMU to assert
with "phys_section_add: Assertion `map->sections_nb < TARGET_PAGE_SIZE'
failed".
Implement the mac-io region aliasing using a single IO memory region that
applies IO_SLICE_MASK representing the maximum size of the aliased region and
then forwarding the access to the existing mac-io memory region using the
address space API.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move all devices from the IO region to within the container in preparation
for updating the IO aliasing mechanism.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the GLUE device to use object_initialize_child().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will allow the q800-glue.h header to be included separately so that the
GLUE device can be referenced externally.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-8-mark.cave-ayland@ilande.co.uk>
[lv: update comment]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Also change the instantiation of the CPU to use object_initialize_child()
followed by a separate realisation.
Restrict valid CPU types to m68040.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-6-mark.cave-ayland@ilande.co.uk>
[lv: update commit message]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will enable us later to distinguish between QOM initialisation and machine
initialisation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This provides an overall container and owner for Machine-related objects such
as MemoryRegions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This brings GLUEState in line with our current QOM guidelines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20230621085353.113233-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Ensure there is a space before the final closing brace for all global
properties.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Mechanical change running Coccinelle spatch with content
generated from the qom-cast-macro-clean-cocci-gen.py added
in the previous commit.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230601093452.38972-3-philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This had been pulled in via qemu/plugin.h from hw/core/cpu.h,
but that will be removed.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230310195252.210956-5-richard.henderson@linaro.org>
[AJB: add various additional cases shown by CI]
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230315174331.2959-15-alex.bennee@linaro.org>
Reviewed-by: Emilio Cota <cota@braap.org>
Snapshot loading is supposed to be deterministic, so we shouldn't
re-randomize the various seeds used.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-id: 20221025004327.568476-8-Jason@zx2c4.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rather than poking directly into RAM, add the bootinfo block as a proper
ROM, so that it's restored when rebooting the system. This way, if the
guest corrupts any of the bootinfo items, but then tries to reboot,
it'll still be restored back to normal as expected.
Then, since the RNG seed needs to be fresh on each boot, regenerate the
RNG seed in the ROM when reseting the CPU.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20221023191340.36238-1-Jason@zx2c4.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Following a change on the kernel side (see link), pass BI_RNG_SEED
instead of BI_VIRT_RNG_SEED. This should have no impact on
compatibility, as there will simply be no effect if it's an old kernel,
which is how things have always been. We then use this as an opportunity
to add this to q800, since now we can, which is a nice improvement.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Laurent Vivier <laurent@vivier.eu>
Link: https://lore.kernel.org/lkml/20220923170340.4099226-3-Jason@zx2c4.com/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-Id: <20220926113900.1256630-1-Jason@zx2c4.com>
[lv: s/^I/ /g]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS CDROM driver uses a SCSI INQUIRY command to check that any SCSI CDROMs
detected match a whitelist of vendors and products before adding them to the
list of available devices.
Add known-good default vendor and product information using the existing
compat_prop mechanism so the user doesn't have to use long command lines to set
the qdev properties manually.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Apple HD SC Setup program uses a SCSI INQUIRY command to check that any SCSI
hard disks detected match a whitelist of vendors and products before allowing
the "Initialise" button to prepare an empty disk.
Add known-good default vendor and product information using the existing
compat_prop mechanism so the user doesn't have to use long command lines to set
the qdev properties manually.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_page_truncated should be enabled for all scsi-cd devices
connected to the q800 machine to allow A/UX to enumerate SCSI CDROM devices
without hanging.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_page_vendor_specific_apple should be enabled for both scsi-hd
and scsi-cd devices to allow MacOS to format SCSI disk devices, and A/UX to
enumerate SCSI CDROM devices succesfully without getting stuck in a loop.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_sense_rom_use_dbd should be enabled for all scsi-cd devices
connected to the q800 machine to correctly report the CDROM block descriptor back
to A/UX.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220622105314.802852-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
By default quirk_mode_page_apple_vendor should be enabled for all scsi-cd devices
connected to the q800 machine to enable MacOS to detect and use them.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220622105314.802852-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The mos6522 datasheet describes how the control lines IRQs are edge-triggered
according to the configuration in the PCR register. Implement the logic according
to the datasheet so that the interrupt bits in IFR are latched when the edge is
detected, and cleared when reading portA/portB or writing to IFR as necessary.
To maintain bisectibility this change also updates the SCSI, SCSI data, Nubus
and VIA2 60Hz/1Hz clocks in the q800 machine to be negative edge-triggered as
confirmed by the PCR programming in all of Linux, NetBSD and MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
"qemu-system-m68k -M q800 -bios /dev/null" crashes with a segfault
in q800_init().
This happens because the code doesn't check that rom_ptr() returned
a non-NULL pointer .
To avoid NULL pointer, don't allow 0 sized file and use bios_size with
rom_ptr().
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/756
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20220107105049.961489-1-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The graphic_depth check is no longer required since commit df8abbbadf ("macfb:
add common monitor modes supported by the MacOS toolbox ROM") which introduced
code in macfb_common_realize() to only allow the resolutions/depths provided in
macfb_mode_table to be specified for each display type.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: df8abbbadf ("macfb: add common monitor modes supported by the MacOS toolbox ROM")
Message-Id: <20211020141810.7875-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This allows the programmer's switch to be triggered via the monitor for debugging
purposes. Since the CPU level 7 interrupt is level-triggered, use a timer to hold
the NMI active for 100ms before releasing it again.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewied-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Explicitly wire up the remaining IRQs in classic mode to enable the use of
g_assert_not_reached() in the default case to detect any unexpected IRQs.
Add a comment explaining the IRQ routing differences in A/UX mode based
upon the comments in NetBSD (also noting that at least A/UX 3.0.1 still
uses classic mode).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When the hardware is operating in classic mode the SONIC on-board Ethernet IRQ is
routed to nubus IRQ 9 instead of directly to the CPU at level 3. This does not
affect the framebuffer which although it exists in slot 9, has its own
dedicated IRQ on the Quadra 800 hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This enables the GLUE logic to change its CPU level IRQ routing depending upon
whether the hardware has been configured for A/UX mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In order to allow dynamic routing of IRQs to different IRQ levels on the CPU
depending upon port B bit 6, use GLUE IRQ numbers and map them to the the
corresponding CPU IRQ level accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
On a Quadra 800 machine Linux sets via_alt_mapping to 1 and clears port B bit 6 to
ensure that the VIA1 IRQ is delivered at level 6 rather than level 1. Even though
QEMU doesn't yet emulate this behaviour, Linux still installs the VIA1 level 1 IRQ
handler regardless of the value of via_alt_mapping which is why the kernel has been
able to boot until now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211020134131.4392-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Whilst the in-built Quadra 800 framebuffer exists within the Nubus address
space for slot 9, it has its own dedicated interrupt on VIA2. Force the
macfb device to occupy slot 9 in the q800 machine and wire its IRQ to the
separate video interrupt since this is what is expected by the MacOS
interrupt handler.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The monitor modes table is found by experimenting with the Monitors Control
Panel in MacOS and analysing the reads/writes. From this it can be found that
the mode is controlled by writes to the DAFB_MODE_CTRL1 and DAFB_MODE_CTRL2
registers.
Implement the first block of DAFB registers as a register array including the
existing sense register, the newly discovered control registers above, and also
the DAFB_MODE_VADDR1 and DAFB_MODE_VADDR2 registers which are used by NetBSD to
determine the current video mode.
These experiments also show that the offset of the start of video RAM and the
stride can change depending upon the monitor mode, so update macfb_draw_graphic()
and both the BI_MAC_VADDR and BI_MAC_VROW bootinfo for the q800 machine
accordingly.
Finally update macfb_common_realize() so that only the resolution and depth
supported by the display type can be specified on the command line, and add an
error hint showing the list of supported resolutions and depths if the user tries
to specify an invalid display mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since the available resolutions and colour depths are determined by the attached
display type, add a qdev property to allow the display type to be specified.
The main resolutions of interest are high resolution 1152x870 with 8-bit colour
and SVGA resolution up to 800x600 with 24-bit colour so update the q800 machine
to allow high resolution mode if specified and otherwise fall back to SVGA.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
