In cmd_features_set_feature() the an offset + data size schemed
is used to allow for large features. Ensure this does not write
beyond the end fo the buffers used to accumulate the full feature
attribute set.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
If len_in is less than the minimum spec allowed value, then return
CXL_MBOX_INVALID_PAYLOAD_LENGTH
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a check that the requested offset + length does not go beyond the end
of the cel_log.
Whilst the cci->cel_log is large enough to include all possible CEL
entries, the guest might still ask for entries beyond the end of it.
Move the comment to this new check rather than before the check on the
type of log requested.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Checking offset + length is of no relevance when verifying the CEL
data will fit in the mailbox payload. Only the length is is relevant.
Note that this removes a potential overflow.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Buggy guest can write a message that advertises more data that
is provided. As QEMU internally duplicates the reported message
size, this may result in an out of bounds access.
Add sanity checks on the size to avoid this.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Buggy software might write a message that is too short for
either the header, or the header + the event data that is specified
in the header. This may result in accesses beyond the range of the
message allocated as a duplicate of the incoming message buffer.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A buggy guest might write an insufficiently large message.
Check the header is present. Whilst zero data after the header is very
odd it will just result in failure to copy any data.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
cxl_cmd_dcd_release_dyn_cap() and cmd_dcd_add_dyn_cap_rsp() are missing
input message size checks. These must be done in the individual
commands when the command has a variable length input payload.
A buggy or malicious guest might send undersized messages via the mailbox.
As that size is used to take a copy of the mailbox content, each command
must check there is sufficient data. In this case the first check is that
there is enough data to read how many extents there are, and the second
that there is enough for those elements to be accessed.
Reported-by: Esifiel <esifiel@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101133917.27634-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the function of retrieving DC extents (cmd_dcd_get_dyn_cap_ext_list),
the output buffer index was not correctly updated while iterating the
extent list on the device, leaving the extents returned incorrect except for
the first one.
Fixes: 1c9221f19e ("hw/mem/cxl_type3: Add DC extent list representative and get DC extent list mailbox support")
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101132005.26633-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the function cmd_firmware_update_get_info for handling Get FW info
command (0x0200h), the vmem, pmem and DC capacity size check were
incorrect. The size should be aligned to 256MiB, not smaller than
256MiB.
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241101132005.26633-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
>From what I read PCI has 32 transactions, PCI Express devices can handle
256 with Extended tag enabled (spec mentions also larger values but I
lack PCIe knowledge).
QEMU leaves 'Extended tag field' with 0 as value:
Capabilities: [e0] Express (v1) Root Complex Integrated Endpoint, IntMsgNum 0
DevCap: MaxPayload 128 bytes, PhantFunc 0
ExtTag- RBE+ FLReset- TEE-IO-
SBSA ACS has test 824 which checks for PCIe device capabilities. BSA
specification [1] (SBSA is on top of BSA) in section F.3.2 lists
expected values for Device Capabilities Register:
Device Capabilities Register Requirement
Role based error reporting RCEC and RCiEP: Hardwired to 1
Endpoint L0s acceptable latency RCEC and RCiEP: Hardwired to 0
L1 acceptable latency RCEC and RCiEP: Hardwired to 0
Captured slot power limit scale RCEC and RCiEP: Hardwired to 0
Captured slot power limit value RCEC and RCiEP: Hardwired to 0
Max payload size value must be compliant with PCIe spec
Phantom functions RCEC and RCiEP: Recommendation is to
hardwire this bit to 0.
Extended tag field Hardwired to 1
1. https://developer.arm.com/documentation/den0094/c/
This change enables Extended tag field. All versioned platforms should
have it disabled for older versions (tested with Arm/virt).
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Message-Id: <20241023113820.486017-1-marcin.juszkiewicz@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VT-d spec removed Transient Mapping (TM) field from second-level page-tables
and treat the field as Reserved(0) since revision 3.2.
Changing the field as reserved(0) will break backward compatibility, so
introduce a property "stale-tm" to allow user to control the setting.
Use pc_compat_9_1 to handle the compatibility for machines before 9.2 which
allow guest to set the field. Starting from 9.2, this field is reserved(0)
by default to match spec. Of course, user can force it on command line.
This doesn't impact function of vIOMMU as there was no logic to emulate
Transient Mapping.
Suggested-by: Yi Liu <yi.l.liu@intel.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Yi Liu <yi.l.liu@intel.com>
Message-Id: <20241028022514.806657-1-zhenzhong.duan@intel.com>
Reviewed-by: Clément Mathieu--Drif<clement.mathieu--drif@eviden.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VHOST_USER_BACKEND_SHARED_OBJECT_ADD and
VHOST_USER_BACKEND_SHARED_OBJECT_REMOVE state
in the spec that they return 0 for successful
operations, non-zero otherwise. However,
implementation relies on the return types
of the virtio-dmabuf library, with opposite
semantics (true if everything is correct,
false otherwise). Therefore, current
implementation violates the specification.
Revert the logic so that the implementation
of the vhost-user handling methods matches
the specification.
Fixes: 043e127a12
Fixes: 1609476662
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Albert Esteve <aesteve@redhat.com>
Message-Id: <20241022124615.585596-1-aesteve@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For the CXL PXB there is additional code after pxb_dev_realize_common()
is called. If that realize failed (e.g. due to an out of range numa_node)
we will get a segfault. Return a bool so the caller can check if the
pxb_dev_realize_common() succeeded or not without having to poke around
in the errp.
Fixes: 4f8db8711c ("hw/pxb: Allow creation of a CXL PXB (host bridge)")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add missing 4 spaces of indent to structure element.
Reported-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
CXL spec 3.1 section 8.2.9.9.11.2 describes the DDR5 Error Check Scrub (ECS)
control feature.
ECS log capabilities field in following ECS tables, which is common for all
memory media FRUs in a CXL device.
Fix struct CXLMemECSReadAttrs and struct CXLMemECSWriteAttrs to make
log entry type field common.
Fixes: 2d41ce38fb ("hw/cxl/cxl-mailbox-utils: Add device DDR5 ECS control feature")
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per cxl spec r3.1, for multiple dynamic capacity event records grouped via
the More flag, the last record in the sequence should clear the More flag.
Before the change, the More flag of the event record is cleared before
the loop of inserting records into the event log, which will leave the flag
always set once it is set in the loop.
Fixes: d0b9b28a5b ("hw/cxl/events: Add qmp interfaces to add/release dynamic capacity extents")
Signed-off-by: Fan Ni <fan.ni@samsung.com>
Link: https://lore.kernel.org/r/20240827164304.88876-2-nifan.cxl@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When injecting a new poisoned region through qmp_cxl_inject_poison(),
the newly injected region should not overlap with existing poisoned
regions.
The current validation method does not consider the following
overlapping region:
┌───┬───────┬───┐
│a │ b(a) │a │
└───┴───────┴───┘
(a is a newly added region, b is an existing region, and b is a
subregion of a)
Fixes: 9547754f40 ("hw/cxl: QMP based poison injection support")
Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current completion percentage calculation does not account for the
relative time since the start of the background activity, this leads to
showing incorrect start percentage vs what has actually been completed.
This patch calculates the percentage based on the actual elapsed time since
the start of the operation.
Fixes: 221d2cfbdb ("hw/cxl/mbox: Add support for background operations")
Signed-off-by: Ajay Joshi <ajay.opensrc@micron.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20240729102338.22337-1-ajay.opensrc@micron.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The sum offset + length may overflow uint32. Since this sum is
compared with uint64_t return value of get_lsa_size(), it makes
sense to choose uint64_t type for offset and length.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 3ebe676a34 ("hw/cxl/device: Implement get/set Label Storage Area (LSA)")
Signed-off-by: Dmitry Frolov <frolov@swemel.ru>
Link: https://lore.kernel.org/r/20240917080925.270597-2-frolov@swemel.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20241014121902.2146424-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
During the hot-unplugging of vhost-user-net type network cards,
the vhost_user_cleanup function may add the same rcu node to
the rcu linked list. The function call in this case is as follows:
vhost_user_cleanup
->vhost_user_host_notifier_remove
->call_rcu(n, vhost_user_host_notifier_free, rcu);
->g_free_rcu(n, rcu);
When this happens, QEMU will abort in try_dequeue:
if (head == &dummy && qatomic_mb_read(&tail) == &dummy.next) {
abort();
}
backtrace is as follows:
0 __pthread_kill_implementation () at /usr/lib64/libc.so.6
1 raise () at /usr/lib64/libc.so.6
2 abort () at /usr/lib64/libc.so.6
3 try_dequeue () at ../util/rcu.c:235
4 call_rcu_thread (0) at ../util/rcu.c:288
5 qemu_thread_start (0) at ../util/qemu-thread-posix.c:541
6 start_thread () at /usr/lib64/libc.so.6
7 clone3 () at /usr/lib64/libc.so.6
The reason for the abort is that adding two identical nodes to
the rcu linked list will cause the rcu linked list to become a ring,
but when the dummy node is added after the two identical nodes,
the ring is opened. But only one node is added to list with
rcu_call_count added twice. This will cause rcu try_dequeue abort.
This happens when n->addr != 0. In some scenarios, this does happen.
For example, this situation will occur when using a 32-queue DPU
vhost-user-net type network card for hot-unplug testing, because
VhostUserHostNotifier->addr will be cleared during the processing of
VHOST_USER_BACKEND_VRING_HOST_NOTIFIER_MSG. However,it is asynchronous,
so we cannot guarantee that VhostUserHostNotifier->addr is zero in
vhost_user_cleanup. Therefore, it is necessary to merge g_free_rcu
and vhost_user_host_notifier_free into one rcu node.
Fixes: 503e355465 ("virtio/vhost-user: dynamically assign VhostUserHostNotifiers")
Signed-off-by: yaozhenguo <yaozhenguo@jd.com>
Message-Id: <20241011102913.45582-1-yaozhenguo@jd.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The XTSup mode enables x2APIC support for AMD IOMMU, which is needed
to support vcpu w/ APIC ID > 255.
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Santosh Shukla <santosh.shukla@amd.com>
Message-Id: <20240927172913.121477-6-santosh.shukla@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In order to support AMD IOMMU interrupt remapping emulation with PCI
pass-through devices, QEMU needs to notify VFIO when guest IOMMU driver
updates and invalidate the guest interrupt remapping table (IRT), and
communicate information so that the host IOMMU driver can update
the shadowed interrupt remapping table in the host IOMMU.
Therefore, send notification when guest IOMMU emulates the IRT
invalidation commands.
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Santosh Shukla <santosh.shukla@amd.com>
Message-Id: <20240927172913.121477-5-santosh.shukla@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Use shared memory region for interrupt remapping which can be
aliased by all devices.
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Santosh Shukla <santosh.shukla@amd.com>
Message-Id: <20240927172913.121477-4-santosh.shukla@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce 'nodma' shared memory region to support PT mode
so that for each device, we only create an alias to shared memory
region when DMA-remapping is disabled.
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Santosh Shukla <santosh.shukla@amd.com>
Message-Id: <20240927172913.121477-3-santosh.shukla@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rename the MMIO memory region variable 'mmio' to 'mr_mmio'
so to correctly name align with struct AMDVIState::variable type.
No functional change intended.
Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Santosh Shukla <santosh.shukla@amd.com>
Message-Id: <20240927172913.121477-2-santosh.shukla@amd.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Note: since all we did is replace VarPackageOp with PackageOP,
and both are represented by Package() in ASL, the AML is
different but ASL is the same.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Message-Id: <20240924132417.739809-4-ribalda@chromium.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Message-Id: <20240924132417.739809-2-ribalda@chromium.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
We moved expected files around, fix up the disassembler script.
Fixes: 7c08eefcaf ("tests/data/acpi: Move x86 ACPI tables under x86/${machine} path")
Fixes: 7434f90467 ("tests/data/acpi/virt: Move ARM64 ACPI tables under aarch64/${machine} path")
Cc: "Sunil V L" <sunilvl@ventanamicro.com>
Message-ID: <ce456091058734b7f765617ac5dfeebcb366d4a9.1730729695.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Add command to sync config from vhost-user backend to the device. It
may be helpful when VHOST_USER_SLAVE_CONFIG_CHANGE_MSG failed or not
triggered interrupt to the guest or just not available (not supported
by vhost-user server).
Command result is racy if allow it during migration. Let's not allow
that.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Raphael Norwitz <raphael@enfabrica.net>
Message-Id: <20240920094936.450987-4-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Split vhost_user_blk_sync_config() out from
vhost_user_blk_handle_config_change(), to be reused in the following
commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Acked-by: Raphael Norwitz <raphael@enfabrica.net>
Message-Id: <20240920094936.450987-3-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Here we just prepare for the following patch, making possible to report
GenericError as recommended.
This patch doesn't aim to prevent further use of DeviceNotFound by
future interfaces:
- find_device_state() is used in blk_by_qdev_id() and qmp_get_blk()
functions, which may lead to spread of DeviceNotFound anyway
- also, nothing prevent simply copy-pasting find_device_state() calls
with false argument
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@yandex-team.ru>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Raphael Norwitz <raphael@enfabrica.net>
Message-Id: <20240920094936.450987-2-vsementsov@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To establish performance characteristics of a CXL device when used via a
particular CXL topology (root ports, switches, end points) it is necessary
to set the appropriate link speed and width in the PCI Express capability
structure. Provide x-speed and x-link properties for this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To establish performance characteristics of a CXL device when used via a
particular CXL topology (root ports, switches, end points) it is necessary
to set the appropriate link speed and width in the PCI Express capability
structure. Provide x-speed and x-link properties for this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst similar to existing PCIESlot link configuration a few registers
need to be set differently so that the downstream device presents
a 'configured' state that is then used to 'train' the upstream port
on the link. Basically that means setting the status register to
reflect it succeeding in training up to target settings.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst not all link related registers are common between RP / Switch DSP
and EP / Switch USP many of them are. Factor that group out to save
on duplication when adding EP / Swtich USP configurability.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Copied from gen_pcie_root_port.c
Drop the previous code that ensured a valid value in s->width, s->speed
as now a default is provided so this will always be set.
Note this changes the default settings but it is unlikely to have a negative
effect on software as will only affect ports with now downstream device.
All other ports will use the settings from that device.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-3-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Approach copied from gen_pcie_root_port.c
Previously the link defaulted to a maximum of 2.5GT/s and 1x. Enable setting
it's maximum values. The actual value after 'training' will depend on the
downstream device configuration.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916173518.1843023-2-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
>From review of the Generic Ports support.
These properties had no description set so add one.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916174321.1843228-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
>From review of generic port introduction.
The value is handled as a uint32_t so store it in that type.
The value cannot in reality exceed MAX_NODES which is currently
128 but if the types are matched there is no need to rely on that
restriction.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916174237.1843213-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These are very similar to the recently added Generic Initiators
but instead of representing an initiator of memory traffic they
represent an edge point beyond which may lie either targets or
initiators. Here we add these ports such that they may
be targets of hmat_lb records to describe the latency and
bandwidth from host side initiators to the port. A discoverable
mechanism such as UEFI CDAT read from CXL devices and switches
is used to discover the remainder of the path, and the OS can build
up full latency and bandwidth numbers as need for work and data
placement decisions.
Acked-by: Markus Armbruster <armbru@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916174122.1843197-1-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reduce the direct use of PCI internals inside ACPI table creation.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-10-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rather than relying on PCI internals, use the new acpi_property
to obtain the ACPI _UID values. These are still the same
as the PCI Bus numbers so no functional change.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-9-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Enable ACPI table creation for PCI Expander Bridges to be independent
of PCI internals. Note that the UID is currently the PCI bus number.
This is motivated by the forthcoming ACPI Generic Port SRAT entries
which can be made completely independent of PCI internals.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-8-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Whilst ACPI SRAT Generic Initiator Afinity Structures are able to refer to
both PCI and ACPI Device Handles, the QEMU implementation only implements
the PCI Device Handle case. For now move the code into the existing
hw/acpi/pci.c file and header. If support for ACPI Device Handles is
added in the future, perhaps this will be moved again.
Also push the struct AcpiGenericInitiator down into the c file as not
used outside pci.c.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Using a property allows us to hide the internal details of the PCI device
from the code to build a SRAT Generic Initiator Affinity Structure with
PCI Device Handle.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-6-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Igor noted that this function only builds one instance, so was rather
misleadingly named. Fix that.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-5-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Rather than attempting to create a generic function with mess of the two
different device handle types, use a PCI handle specific variant. If the
ACPI handle form is needed then that can be introduced alongside this
with little duplicated code.
Drop the PCIDeviceHandle in favor of just passing the bus, devfn
and segment directly. devfn kept as a single byte because ARI means
that in this case it is just an 8 bit function number.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Link: https://lore.kernel.org/qemu-devel/20240618142333.102be976@imammedo.users.ipa.redhat.com/
Tested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240916171017.1841767-4-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
