This simplifies the code and removes the ioeventfd_started
and ioeventfd_set_started callback. The only difference is
in how virtio-ccw handles an error---it doesn't disable
ioeventfd forever anymore. It was the only backend to do
so, and if desired this behavior should be implemented in
virtio-bus.c.
Instead of ioeventfd_started, the ioeventfd_assign callback now
determines whether the virtio bus supports host notifiers.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This simplifies the code and removes the ioeventfd_set_disabled
callback.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide a vmsd pointer for VirtIO devices to use instead of the
load/save methods.
We'll eventually kill off the load/save methods.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Prepare xen_be_del_xendev to be shared with frontends:
* xen_be_del_xendev -> xen_pv_del_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_find_xendev to be shared with frontends:
* xen_be_find_xendev -> xen_pv_find_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_evtchn_event to be shared with frontends:
* xen_be_evtchn_event -> xen_pv_evtchn_event
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_send_notify to be shared with frontends:
* xen_be_send_notify -> xen_pv_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_unbind_evtchn to be shared with frontends:
* xen_be_unbind_evtchn -> xen_pv_unbind_evtchn
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Prepare xen_be_printf to be used by both backend and frontends:
* xen_be_printf -> xen_pv_printf
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
* move xendevs qtail to xen_pvdev.c
* change xen_be_get_xendev to use a new function: xen_pv_insert_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
The name of the functions moved:
* xen_be_evtchn_event
* xen_be_unbind_evtchn
* xen_be_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
The purpose of the new file is to store generic functions shared by frontend
and backends such as xenstore operations, xendevs.
Signed-off-by: Quan Xu <quan.xu@intel.com>
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Fixes:
* WARNING: line over 80 characters
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add support for DRC count indexed hotplug ID type which is primarily
needed for memory hot unplug. This type allows for specifying the
number of DRs that should be plugged/unplugged starting from a given
DRC index.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
* updated rtas_event_log_v6_hp to reflect count/index field ordering
used in PAPR hotplug ACR
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Hotplug events were previously delivered using an EPOW interrupt
and were queued by linux guests into a circular buffer. For traditional
EPOW events like shutdown/resets, this isn't an issue, but for hotplug
events there are cases where this buffer can be exhausted, resulting
in the loss of hotplug events, resets, etc.
Newer-style hotplug event are delivered using a dedicated event source.
We enable this in supported guests by adding standard an additional
event source in the guest device-tree via /event-sources, and, if
the guest advertises support for the newer-style hotplug events,
using the corresponding interrupt to signal the available of
hotplug/unplug events.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ibm,architecture-vec-5 is supposed to encode all option vector 5 bits
negotiated between platform/guest. Currently we hardcode this property
in the boot-time device tree to advertise a single negotiated
capability, "Form 1" NUMA Affinity, regardless of whether or not CAS
has been invoked or that capability has actually been negotiated.
Improve this by generating ibm,architecture-vec-5 based on the full
set of option vector 5 capabilities negotiated via CAS.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In some cases, ibm,client-architecture-support calls can fail. This
could happen in the current code for situations where the modified
device tree segment exceeds the buffer size provided by the guest
via the call parameters. In these cases, QEMU will reset, allowing
an opportunity to regenerate the device tree from scratch via
boot-time handling. There are potentially other scenarios as well,
not currently reachable in the current code, but possible in theory,
such as cases where device-tree properties or nodes need to be removed.
We currently don't handle either of these properly for option vector
capabilities however. Instead of carrying the negotiated capability
beyond the reset and creating the boot-time device tree accordingly,
we start from scratch, generating the same boot-time device tree as we
did prior to the CAS-generated and the same device tree updates as we
did before. This could (in theory) cause us to get stuck in a reset
loop. This hasn't been observed, but depending on the extensiveness
of CAS-induced device tree updates in the future, could eventually
become an issue.
Address this by pulling capability-related device tree
updates resulting from CAS calls into a common routine,
spapr_dt_cas_updates(), and adding an sPAPROptionVector*
parameter that allows us to test for newly-negotiated capabilities.
We invoke it as follows:
1) When ibm,client-architecture-support gets called, we
call spapr_dt_cas_updates() with the set of capabilities
added since the previous call to ibm,client-architecture-support.
For the initial boot, or a system reset generated by something
other than the CAS call itself, this set will consist of *all*
options supported both the platform and the guest. For calls
to ibm,client-architecture-support immediately after a CAS-induced
reset, we call spapr_dt_cas_updates() with only the set
of capabilities added since the previous call, since the other
capabilities will have already been addressed by the boot-time
device-tree this time around. In the unlikely event that
capabilities are *removed* since the previous CAS, we will
generate a CAS-induced reset. In the unlikely event that we
cannot fit the device-tree updates into the buffer provided
by the guest, well generate a CAS-induced reset.
2) When a CAS update results in the need to reset the machine and
include the updates in the boot-time device tree, we call the
spapr_dt_cas_updates() using the full set of negotiated
capabilities as part of the reset path. At initial boot, or after
a reset generated by something other than the CAS call itself,
this set will be empty, resulting in what should be the same
boot-time device-tree as we generated prior to this patch. For
CAS-induced reset, this routine will be called with the full set of
capabilities negotiated by the platform/guest in the previous
CAS call, which should result in CAS updates from previous call
being accounted for in the initial boot-time device tree.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Changed an int -> bool conversion to be more explicit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently we access individual bytes of an option vector via
ldub_phys() to test for the presence of a particular capability
within that byte. Currently this is only done for the "dynamic
reconfiguration memory" capability bit. If that bit is present,
we pass a boolean value to spapr_h_cas_compose_response()
to generate a modified device tree segment with the additional
properties required to enable this functionality.
As more capability bits are added, will would need to modify the
code to add additional option vector accesses and extend the
param list for spapr_h_cas_compose_response() to include similar
boolean values for these parameters.
Avoid this by switching to spapr_ovec_* helpers so we can do all
the parsing in one shot and then test for these additional bits
within spapr_h_cas_compose_response() directly.
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PAPR guests advertise their capabilities to the platform by passing
an ibm,architecture-vec structure via an
ibm,client-architecture-support hcall as described by LoPAPR v11,
B.6.2.3. during early boot.
Using this information, the platform enables the capabilities it
supports, then encodes a subset of those enabled capabilities (the
5th option vector of the ibm,architecture-vec structure passed to
ibm,client-architecture-support) into the guest device tree via
"/chosen/ibm,architecture-vec-5".
The logical format of these these option vectors is a bit-vector,
where individual bits are addressed/documented based on the byte-wise
offset from the beginning of the bit-vector, followed by the bit-wise
index starting from the byte-wise offset. Thus the bits of each of
these bytes are stored in reverse order. Additionally, the first
byte of each option vector is encodes the length of the option vector,
so byte offsets begin at 1, and bit offset at 0.
This is not very intuitive for the purposes of mapping these bits to
a particular documented capability, so this patch introduces a set
of abstractions that encapsulate the work of parsing/encoding these
options vectors and testing for individual capabilities.
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[dwg: Tweaked double-include protection to not trigger a checkpatch
false positive]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For historical reasons construction of the guest device tree in spapr is
divided between spapr_create_fdt_skel() which is called at init time, and
spapr_build_fdt() which runs at reset time. Over time, more and more
things have needed to be moved to reset time.
Previous cleanups mean the only things left in spapr_create_fdt_skel() are
the properties of the root node itself. Finish consolidating these two
parts of device tree construction, by moving this to the start of
spapr_build_fdt(), and removing spapr_create_fdt_skel() entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Construction of the /vdevice node (and its children) is divided between
spapr_create_fdt_skel() (at init time), which creates the base node, and
spapr_populate_vdevice() (at reset time) which creates the nodes for each
individual virtual device.
This consolidates both into a single function called from
spapr_build_fdt().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The /event-sources device tree node is built from spapr_create_fdt_skel().
As part of consolidating device tree construction to reset time, this moves
it to spapr_build_fdt().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
For historical reasons construction of the /rtas node in the device
tree (amongst others) is split into several places. In particular
it's split between spapr_create_fdt_skel(), spapr_build_fdt() and
spapr_rtas_device_tree_setup().
In fact, as well as adding the actual RTAS tokens to the device tree,
spapr_rtas_device_tree_setup() just adds the ibm,lrdr-capacity
property, which despite going in the /rtas node, doesn't have a lot to
do with RTAS.
This patch consolidates the code constructing /rtas together into a new
spapr_dt_rtas() function. spapr_rtas_device_tree_setup() is renamed to
spapr_dt_rtas_tokens() and now only adds the token properties.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
For historical reasons, building the /chosen node in the guest device tree
is split across several places and includes both parts which write the DT
sequentially and others which use random access functions.
This patch consolidates construction of the node into one place, using
random access functions throughout.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Currently the device tree node for the XICS interrupt controller is in
spapr_create_fdt_skel(). As part of consolidating device tree construction
to reset time, this moves it to a function called from spapr_build_fdt().
In addition we move the actual code into hw/intc/xics_spapr.c with the
rest of the PAPR specific interrupt controller code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
At each system reset, the pseries machine needs to load RTAS (the runtime
portion of the guest firmware) into the VM. This means copying
the actual RTAS code into guest memory, and also updating the device
tree so that the guest OS and boot firmware can locate it.
For historical reasons the copy and update to the device tree were in
different parts of the code. This cleanup brings them both together in
an spapr_load_rtas() function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Currently spapr_create_fdt_skel() takes a bunch of individual parameters
for various things it will put in the device tree. Some of these can
already be taken directly from sPAPRMachineState. This patch alters it so
that all of them can be taken from there, which will allow this code to
be moved away from its current caller in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
These values are used only within ppc_spapr_reset(), so just change them
to local variables.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
As Qemu only supports a single instance of the ISA bus, we use the LPC
controller of chip 0 to create one and plug in a couple of useful
devices, like an UART and RTC. An IPMI BT device, which is also an ISA
device, can be defined on the command line to connect an external BMC.
That is for later.
The PowerNV machine now has a console. Skiboot should load a kernel
and jump into it but execution will stop quite early because we lack a
model for the native XICS controller for the moment :
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] XICS: Cannot find a Presentation Controller !
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/powerpc/platforms/powernv/setup.c:81
...
[ 0.000000] NIP [c00000000079d65c] pnv_init_IRQ+0x30/0x44
You can still do a few things under xmon.
Based on previous work from :
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Trivial fix for a change in the serial_hds_isa_init() interface]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LPC (Low Pin Count) interface on a POWER8 is made accessible to
the system through the ADU (XSCOM interface). This interface is part
of set of units connected together via a local OPB (On-Chip Peripheral
Bus) which act as a bridge between the ADU and the off chip LPC
endpoints, like external flash modules.
The most important units of this OPB are :
- OPB Master: contains the ADU slave logic, a set of internal
registers and the logic to control the OPB.
- LPCHC (LPC HOST Controller): which implements a OPB Slave, a set of
internal registers and the LPC HOST Controller to control the LPC
interface.
Four address spaces are provided to the ADU :
- LPC Bus Firmware Memory
- LPC Bus Memory
- LPC Bus I/O (ISA bus)
- and the registers for the OPB Master and the LPC Host Controller
On POWER8, an intermediate hop is necessary to reach the OPB, through
a unit called the ECCB. OPB commands are simply mangled in ECCB write
commands.
On POWER9, the OPB master address space can be accessed via MMIO. The
logic is same but the code will be simpler as the XSCOM and ECCB hops
are not necessary anymore.
This version of the LPC controller model doesn't yet implement support
for the SerIRQ deserializer present in the Naples version of the chip
though some preliminary work is there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- ported on latest PowerNV patchset
- changed the XSCOM interface to fit new model
- QOMified the model
- moved the ISA hunks in another patch
- removed printf logging
- added a couple of UNIMP logging
- rewrote commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that we are using real HW ids for the cores in PowerNV chips, we
can route the XSCOM accesses to them. We just need to attach a
specific XSCOM memory region to each core in the appropriate window
for the core number.
To start with, let's install the DTS (Digital Thermal Sensor) handlers
which should return 38°C for each core.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On a real POWER8 system, the Pervasive Interconnect Bus (PIB) serves
as a backbone to connect different units of the system. The host
firmware connects to the PIB through a bridge unit, the
Alter-Display-Unit (ADU), which gives him access to all the chiplets
on the PCB network (Pervasive Connect Bus), the PIB acting as the root
of this network.
XSCOM (serial communication) is the interface to the sideband bus
provided by the POWER8 pervasive unit to read and write to chiplets
resources. This is needed by the host firmware, OPAL and to a lesser
extent, Linux. This is among others how the PCI Host bridges get
configured at boot or how the LPC bus is accessed.
To represent the ADU of a real system, we introduce a specific
AddressSpace to dispatch XSCOM accesses to the targeted chiplets. The
translation of an XSCOM address into a PCB register address is
slightly different between the P9 and the P8. This is handled before
the dispatch using a 8byte alignment for all.
To customize the device tree, a QOM InterfaceClass, PnvXScomInterface,
is provided with a populate() handler. The chip populates the device
tree by simply looping on its children. Therefore, each model needing
custom nodes should not forget to declare itself as a child at
instantiation time.
Based on previous work done by :
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Added cpu parameter to xscom_complete()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is largy inspired by sPAPRCPUCore with some simplification, no
hotplug for instance. A set of PnvCore objects is added to the PnvChip
and the device tree is populated looping on these cores.
Real HW cpu ids are now generated depending on the chip cpu model, the
chip id and a core mask. The id is propagated to the CPU object, using
properties, to set the SPR_PIR (Processor Identification Register)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Processor Identification Register (PIR) is a register that holds a
processor identifier which is used for bus transactions (XSCOM) and
for processor differentiation in multiprocessor systems. It also used
in the interrupt vector entries (IVE) to identify the thread serving
the interrupts.
P9 and P8 have some differences in the CPU PIR encoding.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be used to build real HW ids for the cores and enforce some
limits on the available cores per chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is is an abstraction of a POWER8 chip which is a set of cores
plus other 'units', like the pervasive unit, the interrupt controller,
the memory controller, the on-chip microcontroller, etc. The whole can
be seen as a socket. It depends on a cpu model and its characteristics:
max cores and specific inits are defined in a PnvChipClass.
We start with an near empty PnvChip with only a few cpu constants
which we will grow in the subsequent patches with the controllers
required to run the system.
The Chip CFAM (Common FRU Access Module) ID gives the model of the
chip and its version number. It is generally the first thing firmwares
fetch, available at XSCOM PCB address 0xf000f, to start initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The goal is to emulate a PowerNV system at the level of the skiboot
firmware, which loads the OS and provides some runtime services. Power
Systems have a lower firmware (HostBoot) that does low level system
initialization, like DRAM training. This is beyond the scope of what
qemu will address in a PowerNV guest.
No devices yet, not even an interrupt controller. Just to get started,
some RAM to load the skiboot firmware, the kernel and initrd. The
device tree is fully created in the machine reset op.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- replaced fprintf by error_report
- used a common definition of _FDT macro
- removed VMStateDescription as migration is not yet supported
- added IBM Copyright statements
- reworked kernel_filename handling
- merged PnvSystem and sPowerNVMachineState
- removed PHANDLE_XICP
- added ppc_create_page_sizes_prop helper
- removed nmi support
- removed kvm support
- updated powernv machine to version 2.8
- removed chips and cpus, They will be provided in another patches
- added a machine reset routine to initialize the device tree (also)
- french has a squelette and english a skeleton.
- improved commit log.
- reworked prototypes parameters
- added a check on the ram size (thanks to Michael Ellerman)
- fixed chip-id cell
- changed MAX_CPUS to 2048
- simplified memory node creation to one node only
- removed machine version
- rewrote the device tree creation with the fdt "rw" routines
- s/sPowerNVMachineState/PnvMachineState/
- etc.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The original QOMification of the spapr VIO devices in 3954d33 "spapr:
convert to QEMU Object Model (v2)" moved some callbacks from the
VIOsPAPRBus structure to the VIOsPAPRDeviceClass. Except, that it
forgot to actually remove them from the VIOsPAPRBus structure (which
still exists, though it doesn't fulfill quite the same function as it
did pre-QOM).
This patch removes those now unused callback fields.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The routines :
void icp_set_cppr(ICPState *icp, uint8_t cppr);
void icp_set_mfrr(ICPState *icp, uint8_t mfrr);
void icp_eoi(ICPState *icp, uint32_t xirr);
now use one 'ICPState *icp' argument instead of a 'XICSState *' and a
server arguments. The backlink on XICSState* is used whenever needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The link will be used to change the API of the icp_* routines which
are still using an XICSState as an argument.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xics_spapr and xics_kvm nearly define the same 'set_nr_servers'
handler. Only the type of the ICP differs. So let's make a common one
to remove some duplicated code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The header now only contains inline functions related to the
Sun NVRAM, so the a name like sun_nvram.h seems to be more
appropriate now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Everything that is related to CHRP NVRAM should rather reside in
chrp_nvram.c / chrp_nvram.h instead of openbios_firmware_abi.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The "system partition" and "free space" partition layouts are
defined by the CHRP and LoPAPR specification, and used by
OpenBIOS and SLOF. We can re-use this code for other machines
that use OpenBIOS and SLOF, too. So let's make this code independent
from the MAC NVRAM environment and put it into two proper helper
functions.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYDmYyAAoJECgHk2+YTcWmoSUP/2ga+b9YmPuyL7XC+12pff0I
Z8gdjUzbMUNcCI0JMZCTGUJbs3BapLcnsA7ypmt88s9kG02WeDMhNx1BfYiAFgLU
kPLQlXAM7awEdGagd3sTCiFojSUZ7GxYHjd5fuhPoOAXvXM8im6zJl18ZcsnStjO
/J8JGoGDHq1XJlz+RIjnGamojJWCiO/+iiD+rFmVSic8zjHPDYq14sIk/QJX+DaF
azLiOI6DAlX3kyrN5ZshhIRQ3COzzUMUSDF/ZaYHjudUco5MBnwj/oLQniTq+ZUd
hCu7dr5TpLxI7q1yltyd0UIl/+aZGbE8tEvoXAtc735iK4m2CTckT7ql6x3xI+Ir
PmpPgIswHqfCiCXm8imLj6ZI47kRA1x4x4AudLaNVKP7jO82485sS9HWpOadYsaU
jvek2SqfqvH+vce4FzwlLEcXGDb73MT/XkIUvd7SfPIbs9umgdZc03U4SHfAWr0i
lAIRs4Ym0AAS2WSE4E09wvdUUr9oxaQBMhw3JAiNmg7hLfyINTP+D/IhtlAVXXEA
F9D7fky5lDwfKvIwPxPJbDD5bCBV9AmxhiahIhv3epu4Kg4orf1inkrx0IZWSbB0
7+JZ7j8asuizfibkeZAN9rxVwmz32makJNsnjzZHlnaPxTvIDzvRkNceBnhC5vKq
3yfxgl4agXmMjveraAtt
=T2kg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
x86 and CPU queue, 2016-10-24
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
# gpg: Signature made Mon 24 Oct 2016 20:51:14 BST
# gpg: using RSA key 0x2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
exec: call cpu_exec_exit() from a CPU unrealize common function
exec: move cpu_exec_init() calls to realize functions
exec: split cpu_exec_init()
pc: q35: Bump max_cpus to 288
pc: Require IRQ remapping and EIM if there could be x2APIC CPUs
pc: Add 'etc/boot-cpus' fw_cfg file for machine with more than 255 CPUs
Increase MAX_CPUMASK_BITS from 255 to 288
pc: Clarify FW_CFG_MAX_CPUS usage comment
pc: kvm_apic: Pass APIC ID depending on xAPIC/x2APIC mode
pc: apic_common: Reset APIC ID to initial ID when switching into x2APIC mode
pc: apic_common: Restore APIC ID to initial ID on reset
pc: apic_common: Extend APIC ID property to 32bit
pc: Leave max apic_id_limit only in legacy cpu hotplug code
acpi: cphp: Force switch to modern cpu hotplug if APIC ID > 254
pc: acpi: x2APIC support for SRAT table
pc: acpi: x2APIC support for MADT table and _MAT method
Conflicts:
target-arm/cpu.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently firmware uses 1 byte at 0x5F offset in RTC CMOS
to get number of CPUs present at boot. However 1 byte is
not enough to handle more than 255 CPUs. So add a new
fw_cfg file that would allow QEMU to tell it.
For compat reasons add file only for machine types that
support more than 255 CPUs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI Spec 6.0 introduces IO Remapping Table Structure. This patch
introduces the definitions required to describe the IO relationship
between the PCIe root complex and the ITS.
This conforms to:
"IO Remapping Table System Software on ARM Platforms",
Document number: ARM DEN 0049B, October 2015.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1476707466-14300-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For most of the timers counter starts to decrement after first period
expires. Due to rounding down performed by the ptimer_get_count, it returns
counter - 1 for the running timer, so that for the ptimer user it looks
like counter gets decremented immediately after running the timer. Add "no
counter round down" policy that provides correct behaviour for those timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: ef39622d0ebfdc32a0877e59ffdf6910dc3db688.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Immediate counter re-load on setting (or on starting to run with)
counter = 0 is a wrong behaviour for some of the timers. Add "no
immediate reload" policy that provides correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: bf9385cd2550ca451d564fa46007688cee3f3d9d.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Performing trigger on setting (or starting to run with) counter = 0 could
be a wrong behaviour for some of the timers, provide "no immediate trigger"
policy to maintain correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 72c0319cf2ec599f22397b7da280c06c34dc40dd.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, periodic timer that has load = delta = 0 performs trigger
on timer reload and stops, printing a "period zero" error message.
Introduce new policy that makes periodic timer to continuously trigger
with a period interval in case of load = 0.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 632b23dd11055d9bd5e338d66b38fac0bd51462e.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, periodic counter wraps around immediately once counter reaches
"0", this is wrong behaviour for some of the timers, resulting in one period
being lost. Add new ptimer policy that provides correct behaviour for such
timers, so that counter stays with "0" for a one period before wrapping
around.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: f22a670cf1f4be298b31640cb5f4be1df0f20ab6.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support target CPUs having a page size which isn't knownn
at compile time. To use this, the CPU implementation should:
* define TARGET_PAGE_BITS_VARY
* not define TARGET_PAGE_BITS
* define TARGET_PAGE_BITS_MIN to the smallest value it
might possibly want for TARGET_PAGE_BITS
* call set_preferred_target_page_bits() in its realize
function to indicate the actual preferred target page
size for the CPU (and report any error from it)
In CONFIG_USER_ONLY, the CPU implementation should continue
to define TARGET_PAGE_BITS appropriately for the guest
OS page size.
Machines which want to take advantage of having the page
size something larger than TARGET_PAGE_BITS_MIN must
set the MachineClass minimum_page_bits field to a value
which they guarantee will be no greater than the preferred
page size for any CPU they create.
Note that changing the target page size by setting
minimum_page_bits is a migration compatibility break
for that machine.
For debugging purposes, attempts to use TARGET_PAGE_SIZE
before it has been finally confirmed will assert.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the property in a CharBackend instead of CharDriverState*. This
also replace systematically chr by chr.chr to access the
CharDriverState*. The following patches will replace it with calls to
qemu_chr_fe CharBackend functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit b6607a1a20, serial_hds_isa_init() was introduced to
factor out serial_isa_init() loops. However, sun4uv shouldn't start from
0 when there is a mm serial on 0 already. Add a "from" argument to
serial_hds_isa_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We should avoid exposing new hardware (through DT and ACPI) on older
machine types. This patch keeps 2.7 and older from changing, despite
the introduction of ITS support for 2.8.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1476117341-32690-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controllers on the Aspeed AST2500 SoC are very similar to the
ones found on the AST2400. The differences are on the number of
supported flash modules and their default mappings in the SoC address
space.
The Aspeed AST2500 has one SPI controller for the BMC firmware and two
for the host firmware. All controllers have now the same set of
registers compatible with the AST2400 FMC controller and the legacy
'SMC' controller is fully gone.
We keep the FMC object to act as the BMC SPI controller and add a new
SPI controller for the host. We also have to introduce new type names
to handle the differences in the flash modules memory mappping.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC has two. Let's prepare ground for the next changes
which will add the required definitions for the second host SPI
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will ease the definition of the new controllers for the AST2500
SoC and also ease the support of the segment registers, which provide
a way to reconfigure the mapping window of each slave.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC has three different types of SMC (Static Memory
Controller) controllers: the SMC (legacy), the FMC (the new one) and
the SPI for the host PNOR. The FMC and the SPI models are now
converging on the AST2500 SoC and the SMC, which was still available
on the AST2400 SoC, was removed.
The Aspeed SoC does not provide support for the legacy SMC
controller. So, let's rename the 'smc' object to 'fmc' to clarify its
nature.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cluster x2APIC cannot work without KVM's x2apic API when the maximal
APIC ID is greater than 8 and only KVM's LAPIC can support x2APIC, so we
forbid other APICs and also the old KVM case with less than 9, to
simplify the code.
There is no point in enabling EIM in forbidden APICs, so we keep it
enabled only for the KVM APIC; unconditionally, because making the
option depend on KVM version would be a maintanance burden.
Old QEMUs would enable eim whenever intremap was on, which would trick
guests into thinking that they can enable cluster x2APIC even if any
interrupt destination would get clamped to 8 bits.
Depending on your configuration, QEMU could notice that the destination
LAPIC is not present and report it with a very non-obvious:
KVM: injection failed, MSI lost (Operation not permitted)
Or the guest could say something about unexpected interrupts, because
clamping leads to aliasing so interrupts were being delivered to
incorrect VCPUs.
KVM_X2APIC_API is the feature that allows us to enable EIM for KVM.
QEMU 2.7 allowed EIM whenever interrupt remapping was enabled. In order
to keep backward compatibility, we again allow guests to misbehave in
non-obvious ways, and make it the default for old machine types.
A user can enable the buggy mode it with "x-buggy-eim=on".
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The default (auto) emulates the current behavior.
A user can now control EIM like
-device intel-iommu,intremap=on,eim=off
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The MMIO based interface to APIC doesn't work well with MSIs that have
upper address bits set (remapped x2APIC MSIs). A specialized interface
is a quick and dirty way to avoid the shortcoming.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every configuration has only up to one APIC class and we'll be extending
the class with a function that can be called without an instanced
object, so a direct access to the class is convenient.
This patch will break compilation if some code uses apic_get_class()
with CONFIG_USER_ONLY.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
In vfio platform vfio_base_device_init we currently just report the
error. Subsequent patches will propagate the error up to the realize
function.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
For the time being let's just simply report the error in
vfio platform's vfio_base_device_init(). A subsequent patch will
duly propagate the error up to vfio_platform_realize.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To prepare for migration to realize, let's use a local error
object in vfio_initfn. Also let's use the same error prefix for all
error messages.
On top of the 1-1 conversion, we start using a common error prefix for
all error messages. We also introduce a similar warning prefix which will
be used later on.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Currently, the MMIO space for accessing PCI on pseries guests begins at
1 TiB in guest address space. Each PCI host bridge (PHB) has a 64 GiB
chunk of address space in which it places its outbound PIO and 32-bit and
64-bit MMIO windows.
This scheme as several problems:
- It limits guest RAM to 1 TiB (though we have a limited fix for this
now)
- It limits the total MMIO window to 64 GiB. This is not always enough
for some of the large nVidia GPGPU cards
- Putting all the windows into a single 64 GiB area means that naturally
aligning things within there will waste more address space.
In addition there was a miscalculation in some of the defaults, which meant
that the MMIO windows for each PHB actually slightly overran the 64 GiB
region for that PHB. We got away without nasty consequences because
the overrun fit within an unused area at the beginning of the next PHB's
region, but it's not pretty.
This patch implements a new scheme which addresses those problems, and is
also closer to what bare metal hardware and pHyp guests generally use.
Because some guest versions (including most current distro kernels) can't
access PCI MMIO above 64 TiB, we put all the PCI windows between 32 TiB and
64 TiB. This is broken into 1 TiB chunks. The first 1 TiB contains the
PIO (64 kiB) and 32-bit MMIO (2 GiB) windows for all of the PHBs. Each
subsequent TiB chunk contains a naturally aligned 64-bit MMIO window for
one PHB each.
This reduces the number of allowed PHBs (without full manual configuration
of all the windows) from 256 to 31, but this should still be plenty in
practice.
We also change some of the default window sizes for manually configured
PHBs to saner values.
Finally we adjust some tests and libqos so that it correctly uses the new
default locations. Ideally it would parse the device tree given to the
guest, but that's a more complex problem for another time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
On real hardware, and under pHyp, the PCI host bridges on Power machines
typically advertise two outbound MMIO windows from the guest's physical
memory space to PCI memory space:
- A 32-bit window which maps onto 2GiB..4GiB in the PCI address space
- A 64-bit window which maps onto a large region somewhere high in PCI
address space (traditionally this used an identity mapping from guest
physical address to PCI address, but that's not always the case)
The qemu implementation in spapr-pci-host-bridge, however, only supports a
single outbound MMIO window, however. At least some Linux versions expect
the two windows however, so we arranged this window to map onto the PCI
memory space from 2 GiB..~64 GiB, then advertised it as two contiguous
windows, the "32-bit" window from 2G..4G and the "64-bit" window from
4G..~64G.
This approach means, however, that the 64G window is not naturally aligned.
In turn this limits the size of the largest BAR we can map (which does have
to be naturally aligned) to roughly half of the total window. With some
large nVidia GPGPU cards which have huge memory BARs, this is starting to
be a problem.
This patch adds true support for separate 32-bit and 64-bit outbound MMIO
windows to the spapr-pci-host-bridge implementation, each of which can
be independently configured. The 32-bit window always maps to 2G.. in PCI
space, but the PCI address of the 64-bit window can be configured (it
defaults to the same as the guest physical address).
So as not to break possible existing configurations, as long as a 64-bit
window is not specified, a large single window can be specified. This
will appear the same way to the guest as the old approach, although it's
now implemented by two contiguous memory regions rather than a single one.
For now, this only adds the possibility of 64-bit windows. The default
configuration still uses the legacy mode.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
The 'spapr-pci-host-bridge' represents the virtual PCI host bridge (PHB)
for a PAPR guest. Unlike on x86, it's routine on Power (both bare metal
and PAPR guests) to have numerous independent PHBs, each controlling a
separate PCI domain.
There are two ways of configuring the spapr-pci-host-bridge device: first
it can be done fully manually, specifying the locations and sizes of all
the IO windows. This gives the most control, but is very awkward with 6
mandatory parameters. Alternatively just an "index" can be specified
which essentially selects from an array of predefined PHB locations.
The PHB at index 0 is automatically created as the default PHB.
The current set of default locations causes some problems for guests with
large RAM (> 1 TiB) or PCI devices with very large BARs (e.g. big nVidia
GPGPU cards via VFIO). Obviously, for migration we can only change the
locations on a new machine type, however.
This is awkward, because the placement is currently decided within the
spapr-pci-host-bridge code, so it breaks abstraction to look inside the
machine type version.
So, this patch delegates the "default mode" PHB placement from the
spapr-pci-host-bridge device back to the machine type via a public method
in sPAPRMachineClass. It's still a bit ugly, but it's about the best we
can do.
For now, this just changes where the calculation is done. It doesn't
change the actual location of the host bridges, or any other behaviour.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
The existing implementation remains same and ics-base is introduced. The
type name "ics" is retained, and all the related functions renamed as
ics_simple_*
This will allow different implementations for the source controllers
such as the MSI support of PHB3 on Power8 which uses in-memory state
tables for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: added ICS_BASE_GET_CLASS and related fixes, based on :
http://patchwork.ozlabs.org/patch/646010/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of an array of fixed sized blocks, use a list, as we will need
to have sources with variable number of interrupts. SPAPR only uses
a single entry. Native will create more. If performance becomes an
issue we can add some hashed lookup but for now this will do fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ move the initialization of list to xics_common_initfn,
restore xirr_owner after migration and move restoring to
icp_post_load]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[ clg: removed the icp_post_load() changes from nikunj patchset v3:
http://patchwork.ozlabs.org/patch/646008/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJX+LTGAAoJEHAbT2saaT5ZIBwH+wfho+xxruEjro6qPvSAtdKk
BBsOWBfBoqWfbAbOxxCO8ina2nA7p5XbyzSXUr94nZhvZMB9BkgL6la03gdS0Yr2
jHf0J9mM8fIbMQFsEKGOPcdpvU7VEXeFwridZYzypiRvbNSdWK3SKVBKgz2ADNhb
l4Tos81IZeH/mw8HcU3XgSGSTV4JuKP4XsnmwlFMa8/sWM/X3vVgx5IG26KURZQm
pW720jcX0meSfji5YvhspfbBbp1g2EorTZb6iLcZf+OUIB6XkViMisVasnyOo2HJ
cehPlhAHixwq1kXGItc1fs11VloZ6hvEZ7kZ615jAdsD2sGJObtGDxgyJW3+gPo=
=HPHj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mjt/tags/trivial-patches-fetch' into staging
trivial patches for 2016-10-08
# gpg: Signature made Sat 08 Oct 2016 09:56:38 BST
# gpg: using RSA key 0x701B4F6B1A693E59
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931 4B22 701B 4F6B 1A69 3E59
* remotes/mjt/tags/trivial-patches-fetch: (26 commits)
net/filter-mirror: Fix mirror initial check typo
virtio: rename the bar index field name in VirtIOPCIProxy
linux-user: include <poll.h> instead of <sys/poll.h>
char: fix missing return in error path for chardev TLS init
CODING_STYLE: Fix a typo ("have" vs. "has")
bitmap: refine and move BITMAP_{FIRST/LAST}_WORD_MASK
build-sys: fix find-in-path
m68k: change default system clock for m5208evb
exec: remove unused compacted argument
usb: ehci: fix memory leak in ehci_process_itd
qapi: make the json schema files more regular.
maint: Add module_block.h to .gitignore
MAINTAINERS: Some updates related to the SH4 machines
MAINTAINERS: Add some more MIPS related files
MAINTAINERS: Add usermode related config files
MAINTAINERS: Add some more pattern to recognize all win32 related files
MAINTAINERS: Add some more rocker related files
MAINTAINERS: Add header files to CRIS section
MAINTAINERS: Add some more files to the virtio section
MAINTAINERS: Add some SPARC machine related files
...
# Conflicts:
# MAINTAINERS
Now all the usages of the old version of VMSTATE_VIRTIO_DEVICE are gone,
so we can get rid of the conditionals, and the old macro.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In most cases the functions passed to VMSTATE_VIRTIO_DEVICE
only call the virtio_load and virtio_save wrappers. Some include some
pre- and post- massaging too. The massaging is better expressed
as such in the VMStateDescription.
Let us prepare for changing the semantic of the VMSTATE_VIRTIO_DEVICE
macro so that it is more similar to the other VMSTATE_*_DEVICE macros
in a sense that it is a field definition.
The preprocessor conditionals are going to be removed as soon as
every usage is converted to the new semantic.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some functions that were called from the dataplane code are now only used
locally:
virtio_blk_init_request()
virtio_blk_handle_request()
virtio_blk_submit_multireq()
since commit "03de2f527499 virtio-blk: do not use vring in dataplane", and
virtio_blk_free_request()
since commit "6aa46d8ff1ee virtio: move VirtQueueElement at the beginning
of the structs".
This patch converts them to static.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
During device reset or similar situations a VirtQueueElement needs to be
freed without pushing it onto the used ring or rewinding the virtqueue.
Extract a new function to do this.
Later patches add virtio_detach_element() calls to existing device so
that scatter-gather lists are unmapped and vq->inuse goes back to zero
during device reset. Currently some devices don't bother and simply
call g_free(elem) which is not a clean way to throw away a
VirtQueueElement.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add support for enabling the virtio 1.0 "emergency write"
(VIRTIO_CONSOLE_F_EMERG_WRITE) feature. The previous patch introduced
the plumbing required for this; now we expose the virtio feature to
the guest. The feature is disabled for compatibility machines to avoid
exposing a new feature to existing guests.
As required by the virtio 1.0 spec, the emergency write functionality
is available to the guest even if the guest doesn't negotatiate the
feature, as well as before feature negotation.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A couple of distributors are compiling their distributions
with "-mcpu=power8" for ppc64le these days, so the user sooner
or later runs into a crash there when not explicitely specifying
the "-cpu POWER8" option to QEMU (which is currently using POWER7
for the "pseries" machine by default). Due to this reason, the
linux-user target already switched to POWER8 a while ago (see commit
de3f1b9841). Since the softmmu target
of course has the same problem, we should switch there to POWER8 for
the newer machine types, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add a generic loader to QEMU which can be used to load images or set
memory values.
Internally inside QEMU this is a device. It is a strange device that
provides no hardware interface but allows QEMU to monkey patch memory
specified when it is created. To be able to do this it has a reset
callback that does the memory operations.
This device allows the user to monkey patch memory. To be able to do
this it needs a backend to manage the datas, the same as other
memory-related devices. In this case as the backend is so trivial we
have merged it with the frontend instead of creating and maintaining a
seperate backend.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-id: 10f2a9dce5e5e11b6c6d959415b0ad6ee22bcba5.1475195078.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ACPI Spec 6.0 introduces GIC Interrupt Translation Service Structure.
Here we add the definition of the Structure.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-8-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the basic skeleton for both KVM and software-emulated ITS.
Since we already prepare status structure, we also introduce complete
VMState description. But, because we currently have no migratable
implementations, we also set unmigratable flag.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the STM32F2xx ADC device. This device randomly
generates values on each read.
This also includes creating a hw/adc directory.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 3240e660adaf537f55a63ce06096e844aece8cda.1474742262.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
