Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-22-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-21-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With target-specific modules we can have multiple modules implementing
the same object. Therefore we have to check the target arch on lookup
to find the correct module.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-20-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add module_allow_arch() to set the target architecture.
In case a module is limited to some arch verify arches
match and ignore the module if not.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-19-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
One for module load and one for qom type lookup.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-18-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use module database to figure which module adds given QemuOpts group.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-17-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use module database to figure which module implements a given QOM type.
Drop hard-coded object list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-16-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use module database for module dependencies.
Drop hard-coded dependency list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-15-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-14-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-13-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-12-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-11-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-10-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-9-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-8-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-7-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-6-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Verifies if all dependencies are correctly listed in the modinfo.c too
and stop the builds if they're not.
Signed-off-by: Jose R. Ziviani <jziviani@suse.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-5-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add script to generate C source with a small
database containing the module meta-data.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-4-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add script to collect the module meta-data from the source code,
store the results in *.modinfo files.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-3-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add macros for module info annotations.
Instead of having that module meta-data stored in lists in util/module.c
place directly in the module source code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Jose R. Ziviani <jziviani@suse.de>
Message-Id: <20210624103836.2382472-2-kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While config-host.mak entries are expanded to "1" for compatibility with
create-config.sh, tests done directly in meson.build expand to the empty
string and cannot be placed to the right of the && operator. Adjust
osdep.h after commit e46bd55d9c ("configure: convert HAVE_BROKEN_SIZE_MAX
to meson", 2021-07-06) changed the way HAVE_BROKEN_SIZE_MAX is defined.
Reported-by: Frederic Bezies <fredbezies@gmail.com>
Fixes: e46bd55d9c ("configure: convert HAVE_BROKEN_SIZE_MAX to meson", 2021-07-06)
Resolves: #463
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While most libraries do not need a CONFIG_* symbol because the
"when:" clauses are enough, some do. Add them back or stop
using them if possible.
In the case of libpmem, the statement to add the CONFIG_* symbol
was still in configure, but could not be triggered because it
checked for "no" instead of "disabled" (and it would be wrong anyway
since the test for the library has not been done yet).
Reported-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Fixes: 587d59d6cc ("configure, meson: convert virgl detection to meson", 2021-07-06)
Fixes: 83ef16821a ("configure, meson: convert libdaxctl detection to meson", 2021-07-06)
Fixes: e36e8c70f6 ("configure, meson: convert libpmem detection to meson", 2021-07-06)
Fixes: 53c22b68e3 ("configure, meson: convert liburing detection to meson", 2021-07-06)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For some reason, libpmem option setting was set to work in an opposite
way (--enable-libpmem disabled it and vice versa). Fixing this so
configuration works properly.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Connor Kuehl <ckuehl@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@ionos.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Connor Kuehl <ckuehl@redhat.com>
Message-Id: <20210707075144.82717-1-mrezanin@redhat.com>
Fixes: e36e8c70f6 ("configure, meson: convert libpmem detection to meson", 2021-07-06)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For some reason, libdaxctl option setting was set to work in an opposite
way (--enable-libdaxctl disabled it and vice versa). Fixing this so
configuration works properly.
Signed-off-by: Miroslav Rezanina <mrezanin@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210707063124.81954-1-mrezanin@redhat.com>
Fixes: 83ef16821a ("configure, meson: convert libdaxctl detection to meson", 2021-07-06)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a space in the message printed when gicr_read*/gicr_write* returns
MEMTX_ERROR in arm_gicv3_redist.c.
Signed-off-by: Rebecca Cran <rebecca@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210706211432.31902-1-rebecca@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Nick Hudson <hnick@vmware.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The stellaris board doesn't emulate the handling of the OLED
chipselect line correctly. Expand the comment describing this,
including a sketch of the theoretical correct way to do it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Luminary PL061s in the Stellaris LM3S9695 don't all have the same
reset value for GPIOPUR. We can get away with not letting the board
configure the PUR reset value because we don't actually wire anything
up to the lines which should reset to pull-up. Add a comment noting
this omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The PL061 comes out of reset with all its lines configured as input,
which means they might need to be pulled to 0 or 1 depending on the
'pullups' and 'pulldowns' properties. Currently we do not assert
these lines on reset; they will only be set whenever the guest first
touches a register that triggers a call to pl061_update().
Convert the device to three-phase reset so we have a place where we
can safely call qemu_set_irq() to set the floating lines to their
correct values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For the virt board we have two PL061 devices -- one for NonSecure which
is inputs only, and one for Secure which is outputs only. For the former,
we don't care whether its outputs are pulled low or high when the line is
configured as an input, because we don't connect them. For the latter,
we do care, because we wire the lines up to the gpio-pwr device, which
assumes that level 1 means "do the action" and 1 means "do nothing".
For consistency in case we add more outputs in future, configure both
PL061s to pull GPIO lines down to 0.
Reported-by: Maxim Uvarov <maxim.uvarov@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The PL061 GPIO does not itself include pullup or pulldown resistors
to set the value of a GPIO line treated as an output when it is
configured as an input (ie when the PL061 itself is not driving it).
In real hardware it is up to the board to add suitable pullups or
pulldowns. Currently our implementation hardwires this to "outputs
pulled high", which is correct for some boards (eg the realview ones:
see figure 3-29 in the "RealView Platform Baseboard for ARM926EJ-S
User Guide" DUI0224I), but wrong for others.
In particular, the wiring in the 'virt' board and the gpio-pwr device
assumes that wires should be pulled low, because otherwise the
pull-to-high will trigger a shutdown or reset action. (The only
reason this doesn't happen immediately on startup is due to another
bug in the PL061, where we don't assert the GPIOs to the correct
value on reset, but will do so as soon as the guest touches a
register and pl061_update() gets called.)
Add properties to the pl061 so the board can configure whether it
wants GPIO lines to have pullup, pulldown, or neither.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The Luminary variant of the PL061 has registers GPIOPUR and GPIOPDR
which lets the guest configure whether the GPIO lines are pull-up,
pull-down, or truly floating. Instead of assuming all lines are pulled
high, honour the PUR and PDR registers.
For the plain PL061, continue to assume that lines have an external
pull-up resistor, as we did before.
The stellaris board actually relies on this behaviour -- the CD line
of the ssd0323 display device is connected to GPIO output C7, and it
is only because of a different bug which we're about to fix that we
weren't incorrectly driving this line high on reset and putting the
ssd0323 into data mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add a comment documenting the "QEMU interface" of this device:
which MMIO regions, IRQ lines, GPIO lines, etc it exposes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add tracepoints for reads and writes to the PL061 registers. This requires
restructuring pl061_read() to only return after the tracepoint, rather
than having lots of early-returns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Currently the pl061_read() and pl061_write() functions handle offsets
using a combination of three if() statements and a switch(). Clean
this up to use just a switch, using case ranges.
This requires that instead of catching accesses to the luminary-only
registers on a stock PL061 via a check on s->rsvd_start we use
an "is this luminary?" check in the cases for each luminary-only
register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Convert the use of the DPRINTF debug macro in the PL061 model to
use tracepoints.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
icv_eoir_write() and icv_dir_write() ignore invalid virtual IRQ numbers
(like LPIs). The issue is that these functions check against the number
of implemented IRQs (QEMU's default is num_irq=288) which can be lower
than the maximum virtual IRQ number (1020 - 1). The consequence is that
if a hypervisor creates an LR for an IRQ between 288 and 1020, then the
guest is unable to deactivate the resulting IRQ. Note that other
functions that deal with large IRQ numbers, like icv_iar_read, check
against 1020 and not against num_irq.
Fix the checks by using GICV3_MAXIRQ (1020) instead of the number of
implemented IRQs.
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Message-id: 20210702233701.3369-1-ricarkol@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
New mini-kernel test for STM32VLDISCOVERY USART1.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-5-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the target guide for Netduino 2, Netduino Plus 2 and STM32VLDISCOVERY.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-4-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This SoC is similar to stm32f205 SoC.
This will be used by the STM32VLDISCOVERY to create a machine.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-2-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch drops the 'x-' prefix from x-blockdev-reopen.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-7-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This test swaps the images used by two active block devices.
This is now possible thanks to the new ability to run
x-blockdev-reopen on multiple devices at the same time.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-6-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
[ kwolf: Fixed AioContext locking ]
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-5-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
As the BlockReopenQueue can contain nodes in multiple AioContexts, only
one of which may be locked when AIO_WAIT_WHILE() can be called, we can't
let the caller lock the right contexts. Instead, individually lock the
AioContext of a single node when iterating the queue.
Reintroduce bdrv_reopen() as a wrapper for reopening a single node that
drains the node and temporarily drops the AioContext lock for
bdrv_reopen_multiple().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the code to free a BlockReopenQueue to a separate function.
It will be used in a subsequent patch.
[ kwolf: Also free explicit_options and options, and explicitly
qobject_ref() the value when it continues to be used. This makes
future memory leaks less likely. ]
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210708114709.206487-3-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Without an external data file, s->data_file is a second pointer with the
same value as bs->file. When changing bs->file to a different BdrvChild
and freeing the old BdrvChild, s->data_file must also be updated,
otherwise it points to freed memory and causes crashes.
This problem was caught by iotests case 245.
Fixes: df2b7086f169239ebad5d150efa29c9bb6d4f820
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210708114709.206487-2-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When removeing support for qemu-img being able to create backing
chains without embedded backing formats, we caused a poor error
message as caught by iotest 114. Improve the situation to inform the
user what went wrong.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210708155228.2666172-1-eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
