make qdev_unplug()/device_set_realized() to call hotplug handler's
plug/unplug methods if available and remove not needed anymore
hot(un)plug handling from PCIDevice.
In case if hotplug handler is not available, revert to the legacy
hotplug method for compatibility with not yet converted buses.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Split pcie_cap_slot_hotplug() into hotplug/unplug callbacks
and register them as "hotplug-handler" interface implementation of
PCIE_SLOT device.
Replace pci_bus_hotplug() wiring with setting link on PCI BUS
"hotplug-handler" property to PCI_BRIDGE_DEV device.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Split shpc_device_hotplug() into hotplug/unplug callbacks
and register them as "hotplug-handler" interface implementation of
PCI_BRIDGE_DEV device.
Replace pci_bus_hotplug() wiring with setting link on PCI BUS
"hotplug-handler" property to PCI_BRIDGE_DEV device.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Split piix4_device_hotplug() into hotplug/unplug callbacks
and register them as "hotplug-handler" interface implementation of
PIIX4_PM device.
Replace pci_bus_hotplug() wiring with setting link on
PCI BUS "hotplug-handler" property to PIIX4_PM device.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Get rid of PCIDevice specific PCIDeviceClass.no_hotplug and use
generic DeviceClass.hotpluggable field instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently it's possible to make PCIDevice not hotpluggable
by using no_hotplug field of PCIDeviceClass. However it
limits this only to PCI devices and prevents from
generalizing hotplug code.
So add similar field to DeviceClass so it could be reused
with other Devices and would allow to replace PCI specific
hotplug callbacks with generic implementation. Following
patches will replace PCIDeviceClass.no_hotplug with this
new property.
In addition expose field as "hotpluggable" readonly property,
to make it possible to read its value via QOM interface.
Make DeviceClass hotpluggable by default as it was assumed
before.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will allow to reuse field with different BUSes,
reducing code duplication. Field is intended for
replacing 'hotplug_qdev' field in PCIBus and also
will allow to avoid adding equivalent field to
DimmBus with possiblitity to refactor other BUSes
to use it instead of custom field.
In addition once all users of allow_hotplug field
are converted to new API, link could replace
allow_hotplug field in qdev hotplug code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide a generic hotplug interface for hotplug handlers.
Intended for replacing hotplug mechanism used by
PCI/PCIE/SHPC code and will be used for memory hotplug.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Document that get_image_size sets errno
on failure.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds support for the Fast Ethernet MAC found on Allwinner
SoCs, together with a basic emulation of Realtek RTL8201CP PHY.
Since there is no public documentation of the Allwinner controller, the
implementation is based on Linux kernel driver.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patch adds functions fifo8_push_all() and fifo8_pop_buf() which
can be used respectively to push the content of a memory buffer to the
fifo and to pop multiple bytes obtaining a pointer to the fifo backing
buffer.
In addition, it implements fifo8_num_free() and fifo8_num_used() which
allow to check if a multi-byte operation can be performed.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use libvixl to implement disassembly output in debug
logs for A64, for use with both AArch64 hosts and targets.
Signed-off-by: Claudio Fontana <claudio.fontana@linaro.org>
[PMM:
* added support for target disassembly
* switched to custom QEMUDisassembler so the output format
matches what QEMU expects
* make sure we correctly fall back to "just print hex"
if we didn't build the AArch64 disassembler because of
lack of a C++ compiler
* rename from 'aarch64' to 'arm-a64' because this is a
disassembler for the A64 instruction set
* merge aarch64.c and aarch64-cxx.cc into one C++ file
* simplify the aarch64.c<->aarch64-cxx.cc interface]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICC_APRn registers are not currently supported by the ARM GIC v2.0
emulation. This patch adds the missing state.
Note that we also change the number of APRs to use a define GIC_NR_APRS
based on the maximum number of preemption levels. This patch also adds
RAZ/WI accessors for the four registers on the emulated CPU interface.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for saving VMState of 2D arrays of uint32 values.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a binary_point field to the gic emulation structure and support
setting/getting this register now when we have it. We don't actually
support interrupt grouping yet, oh well.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Right now the arm gic emulation doesn't keep track of the source of an
SGI (which apparently Linux guests don't use, or they're fine with
assuming CPU 0 always).
Add the necessary matrix on the GICState structure and maintain the data
when setting and clearing the pending state of an IRQ and make the state
visible to the guest.
Note that we always choose to present the source as the lowest-numbered
CPU in case multiple cores have signalled the same SGI number to a core
on the system.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vMR+
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20140204-1' into staging
migration/next for 20140204
# gpg: Signature made Tue 04 Feb 2014 15:52:00 GMT using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20140204-1:
Don't abort on memory allocation error
Don't abort on out of memory when creating page cache
XBZRLE cache size should not be larger than guest memory size
migration:fix free XBZRLE decoded_buf wrong
Add check for cache size smaller than page size
Set xbzrle buffers to NULL after freeing them to avoid double free errors
exec: fix ram_list dirty map optimization
vmstate: Make VMSTATE_STRUCT_POINTER take type, not ptr-to-type
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qtest driver always uses signals to kill qemu
no need to report it, whatever the accelerator state.
Add API to detect qtest driver, and suppress reporting
signals in this case.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
reduces acpi PCI hotplug code duplication by ~200LOC
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove now unused 'device_present' field wich was obsoleted by
patch "pcihp: reduce number of device check events"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
due to recent change introduced by:
"pcihp: reduce number of device check events"
'up' field is cleared right after it's read.
This is incompatible with legacy BIOS ACPI code
where PCNF ACPI method reads this field 32 times.
To make pci_read mmio callback compatible with legacy
'up' behavior, pcihp code will need to know in which
mode it runs add 'legacy_piix' field to AcpiPciHpState
structure and alter register behavior accordingly.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PIIX created a made-up value for the UP register since it was read by
guest 32 times for each interrupt.
There's no reason to do this for the new PCIHP: register is only read
once for each interrupt, so clean up code by making read act as an
interrupt acknowledgement: the new UP register clear on read.
In this way we cut down the number of bus rescans
by a factor of 32, and drop a bunch of code that's
now unused.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
the initial sclp defines (without code yet) for standby memory (some
sort of memory hotplug) as well as a cleanup of the kvm register
synchronization.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Aodz
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/kvm-s390-20140131' into staging
This patch set contains the sclp defines and events for cpu hotplug,
the initial sclp defines (without code yet) for standby memory (some
sort of memory hotplug) as well as a cleanup of the kvm register
synchronization.
# gpg: Signature made Fri 31 Jan 2014 08:54:29 GMT using RSA key ID B5A61C7C
# gpg: Can't check signature: public key not found
* remotes/borntraeger/tags/kvm-s390-20140131:
s390x/kvm: cleanup partial register handling
sclp-s390: Define new SCLP codes and structures
s390-sclp: SCLP Event integration
s390-sclp: SCLP CPU Info
s390-sclp: Define New SCLP Codes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is better to fail migration in case of failure to
allocate new cache item
Signed-off-by: Orit Wasserman <owasserm@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When qemu do live migration with xbzrle, qemu malloc decoded_buf
at destination end but free it at source end. It will crash qemu
by double free error in some scenarios. Splitting the XBZRLE structure
for clear logic distinguishing src/dst side.
Signed-off-by: ChenLiang <chenliang88@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: GongLei <arei.gonglei@huawei.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The ae2810c4bb patch introduced
optimization for ram_list.dirty_memory update. However it can only
work correctly if hpratio is 1 as the @bitmap parameter stores 1 bits
per system page size (may vary, 4K or 64K on PPC64) and
ram_list.dirty_memory stores 1 bit per TARGET_PAGE_SIZE
(which is hardcoded to 4K).
This fixes hpratio!=1 case to fall back to the slow path.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The VMSTATE_STRUCT_POINTER macros are a bit odd in that they
must be passed an argument "FooType *" rather than just taking
the FooType. They're only used in one place, so it's easy to
tidy this up. This also lets us use the macro to replace the
hand-rolled VMSTATE_PTIMER.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Juan Quintela <quintela@redhat.com>
* implementation of first part of the A64 Neon instruction set
* v8 AArch32 rounding and 16<->64 fp conversion instructions
* fix MIDR value on Zynq boards
* some minor bugfixes/code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KIzb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'pmaydell/tags/pull-target-arm-20140131' into staging
target-arm queue:
* implementation of first part of the A64 Neon instruction set
* v8 AArch32 rounding and 16<->64 fp conversion instructions
* fix MIDR value on Zynq boards
* some minor bugfixes/code cleanups
# gpg: Signature made Fri 31 Jan 2014 15:06:34 GMT using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
* pmaydell/tags/pull-target-arm-20140131: (34 commits)
arm_gic: Fix GICD_ICPENDR and GICD_ISPENDR writes
arm_gic: Introduce define for GIC_NR_SGIS
target-arm: A64: Add SIMD shift by immediate
target-arm: A64: Add simple SIMD 3-same floating point ops
target-arm: A64: Add integer ops from SIMD 3-same group
target-arm: A64: Add logic ops from SIMD 3 same group
target-arm: A64: Add top level decode for SIMD 3-same group
target-arm: A64: Add SIMD scalar 3 same add, sub and compare ops
target-arm: A64: Add SIMD three-different ABDL instructions
target-arm: A64: Add SIMD three-different multiply accumulate insns
target-arm: Add AArch32 SIMD VCVTA, VCVTN, VCVTP and VCVTM
target-arm: Add AArch32 FP VCVTA, VCVTN, VCVTP and VCVTM
target-arm: Add AArch32 SIMD VRINTA, VRINTN, VRINTP, VRINTM, VRINTZ
target-arm: Add set_neon_rmode helper
target-arm: Add support for AArch32 SIMD VRINTX
target-arm: Add support for AArch32 FP VRINTX
target-arm: Add support for AArch32 FP VRINTZ
target-arm: Add support for AArch32 FP VRINTR
target-arm: Add AArch32 FP VRINTA, VRINTN, VRINTP and VRINTM
target-arm: Move arm_rmode_to_sf to a shared location.
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes a compiler warning with -Werror=missing-format-attribute
and allows improved compiler checks for variable argument lists.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Do not rely on int8_t (and friends) not being preprocessor
symbols (or symbols expanding to themselves). On NetBSD (for example) the
glue(u, SDATA_TYPE) results in u__int8_t, which is undefined. There is no way
to stop cpp expanding inner macros, so just add the few lines explicitly and
get rid of the magic.
Signed-off-by: Martin Husemann <martin@NetBSD.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Instead of hardcoding 16 various places in the code, use a define to
make it more clear what is going on.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This includes new unit-tests for acpi by Marcel,
hotplug for pci bridges by myself (piix only so far)
and cpu hotplug for q35.
And a bunch of fixes all over the place as usual.
I included the patch to fix memory alignment for q35
as well - even though it limits 32 bit guests to 3G (they
previously could address more memory with PAE).
To remove the limit, this will have to be fixed in seabios.
I also added self as virtio co-maintainer so I don't need
to troll the list for patches to review.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS5O2JAAoJECgfDbjSjVRpBRsH/iueYMYqtlIOCFSBf4TSU5LN
3369DwM0EncrEIZhv6jjtX+CSKUca9IXkKcvBBHJOTwhUodGNZ1wJ/FpO9+AhjpB
5XlIcF4nOi2eYDGs/8JToecK+edggTrSjJ8Bg5n7/bEtJ/oNyjTQ0RMX+2jXq1y3
jnpVjO1ntQXkZQZWNM3O+8biVT1o8wJlFhFbYpx4TKgFplPnRrg1gZR3MtnhsZ+M
OoBenpJYrh5Gw52d6HPauMDAux51MjGymzrk2Wmd/w3hPMP9BcxX7NvoapKlGTg9
DkVr7cvbIzZ2JnsRLFNeWsJIupOjl6MwqhGJo5WcB5VS7NZTbVHmtBRvqKa76EU=
=y3wE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi,pci,pc,virtio fixes and enhancements
This includes new unit-tests for acpi by Marcel,
hotplug for pci bridges by myself (piix only so far)
and cpu hotplug for q35.
And a bunch of fixes all over the place as usual.
I included the patch to fix memory alignment for q35
as well - even though it limits 32 bit guests to 3G (they
previously could address more memory with PAE).
To remove the limit, this will have to be fixed in seabios.
I also added self as virtio co-maintainer so I don't need
to troll the list for patches to review.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 26 Jan 2014 11:12:09 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* mst/tags/for_anthony: (35 commits)
MAINTAINERS: add self as virtio co-maintainer
q35: document gigabyte_align
q35: gigabyte alignment for ram
acpi: Fix PCI hole handling on build_srat()
pc: Save size of RAM below 4GB
hw/pci: fix error flow in pci multifunction init
acpi-test: update expected AML since recent changes
pc: ACPI: update acpi-dsdt.hex.generated q35-acpi-dsdt.hex.generated
pc: ACPI: unify source of CPU hotplug IO base/len
pc: ACPI: expose PRST IO range via _CRS
pc: Q35 DSDT: exclude CPU hotplug IO range from PCI bus resources
pc: PIIX DSDT: exclude CPU/PCI hotplug & GPE0 IO range from PCI bus resources
pc: set PRST base in DSDT depending on chipset
acpi: ich9: add CPU hotplug handling to Q35 machine
acpi: factor out common cpu hotplug code for PIIX4/Q35
acpi-build: enable hotplug for PCI bridges
piix4: add acpi pci hotplug support
pcihp: generalization of piix4 acpi
pci: add pci_for_each_bus_depth_first
pc: make: fix dependencies: rebuild when included file is changed
...
Message-id: 1390735289-15563-1-git-send-email-mst@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
in addition fix default backend leak by releasing it if its
initialization failed.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Introduces USER_CREATABLE interface that must be implemented by
objects which are designed to created with -object CLI option or
object-add QMP command.
Interface provides an ability to do an optional second stage
initialization of the object created with -object/object-add
commands. By providing complete() callback, which is called
after the object properties were set.
It allows to:
* prevents misusing of -object/object-add by filtering out
objects that are not designed for it.
* generalize second stage backend initialization instead of
adding custom APIs to perform it
* early error detection of backend initialization at -object/
object-add time rather than through a proxy DEVICE object
that tries to use backend.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Define new SCLP codes and structures that will be needed for
s390 memory hotplug.
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The ram_below_4g value will be useful in other places, such as the ACPI
table code, and other code that currently requires passing
below_4g_mem_size around in function arguments.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
use C headers defines as source of IO base/len for respective
values in ASL code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
.. use IO port 0cd8-0xcf7 range for CPU present bitmap
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
.. so it could be used for adding CPU hotplug to Q35 machine
Add an additional header with that will be shared between
C and ASL code: include/hw/acpi/cpu_hotplug_defs.h
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add support for acpi pci hotplug using the
new infrastructure.
PIIX4 legacy interface is maintained as is for
machine types 1.7 and older.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add ACPI based PCI hotplug library with bridge hotplug
support.
Design
- each bus gets assigned "bsel" property.
- ACPI code writes this number
to a new BNUM register, then uses existing
UP/DOWN registers to probe slot status;
to eject, write number to BNUM register,
then slot into existing EJ.
The interface is actually backwards-compatible with
existing PIIX4 ACPI (though not migration compatible).
This is split out from PIIX4 codebase so we can
reuse it for Q35 as well.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
AppleSMC (-device isa-applesmc) is required to boot OS X guests.
OS X expects a SMC node to be present in the ACPI DSDT. This patch
adds a SMC node to the DSDT, and dynamically patches the return value
of SMC._STA to either 0x0B if the chip is present, or otherwise to 0x00,
before booting the guest.
Signed-off-by: Gabriel Somlo <somlo@cmu.edu>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sFbE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kraxel/tags/pull-usb-2' into staging
usb core+hid: add support for microsoft os descriptors
# gpg: Signature made Tue 21 Jan 2014 02:21:29 AM PST using RSA key ID D3E87138
# gpg: Can't check signature: public key not found
* kraxel/tags/pull-usb-2:
usb-hid: add microsoft os descriptor support
usb: add support for microsoft os descriptors
Message-id: 1390299772-5368-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Instead of implementing the alignment adjustment here, use the now
existing functionality of bdrv_co_do_pwritev().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
We can only have a single wait_serialising_requests() call per request
because otherwise we can run into deadlocks where requests are waiting
for each other. The same is true when wait_serialising_requests() is not
at the very beginning of a request, so that other requests can be issued
between the start of the tracking and wait_serialising_requests().
Fix this by changing wait_serialising_requests() to ignore requests that
are already (directly or indirectly) waiting for the calling request.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Copy on Read wants to serialise with all requests touching the same
cluster, so wait_serialising_requests() rounded to cluster boundaries.
Other users like alignment RMW will have different requirements, though
(requests touching the same sector), so make it dynamic.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Change the API so that specific requests can be marked serialising. Only
these requests are checked for overlaps then.
This means that during a Copy on Read operation, not all requests
overlapping other requests are serialised any more, but only those that
actually overlap with the specific COR request.
Also remove COR from function and variable names because this
functionality can be useful in other contexts.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Add a bs->request_alignment field that contains the required
offset/length alignment for I/O requests and fill it in the raw block
drivers. Use ioctls if possible, else see what alignment it takes for
O_DIRECT to succeed.
While at it, also expose the memory alignment requirements, which may be
(and in practice are) different from the disk alignment requirements.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The alignment field is now set to the value that is promised to the
guest, rather than required by the host. The next patches will make
QEMU aware of the host-provided values, so make this clear.
The alignment is also not about memory buffers, but about the sectors on
the disk, change the documentation of the field.
At this point, the field is set by the device emulation, but completely
ignored by the block layer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
bs->buffer_alignment is set by the device emulation and contains the
logical block size of the guest device. This isn't something that the
block layer should know, and even less something to use for determining
the right alignment of buffers to be used for the host.
The new BlockLimits field opt_mem_alignment tells the qemu block layer
the optimal alignment to be used so that no bounce buffer must be used
in the driver.
This patch may change the buffer alignment from 4k to 512 for all
callers that used qemu_blockalign() with the top-level image format
BlockDriverState. The value was never propagated to other levels in the
tree, so in particular raw-posix never required anything else than 512.
While on disks with 4k sectors direct I/O requires a 4k alignment,
memory may still be okay when aligned to 512 byte boundaries. This is
what must have happened in practice, because otherwise this would
already have failed earlier. Therefore I don't expect regressions even
with this intermediate state. Later, raw-posix can implement the hook
and expose a different memory alignment requirement.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
When reopening with different flags, or when backing files disappear
from the chain, the limits may change. Make sure they get updated in
these cases.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoît Canet <benoit@irqsave.net>
This function separates filling the BlockLimits from bdrv_open(), which
allows it to call it from other operations which may change the limits
(e.g. modifications to the backing file chain or bdrv_reopen)
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
There was two candidate ways to implement named node manipulation:
1)
{ 'command': 'block_passwd', 'data': {'*device': 'str',
'*node-name': 'str', 'password': 'str'}
}
2)
{ 'command': 'block_passwd', 'data': {'device': 'str',
'*device-is-node': 'bool',
'password': 'str'} }
Luiz proposed 1 and says 2 was an abuse of the QMP interface and proposed to
rewrite the QMP block interface for 2.0.
Luiz does not like in 1 the fact that 2 fields are optional but one of them must
be specified leading to an abuse of the QMP semantic.
Kevin argumented that 2 what a clear abuse of the device field and would not be
practical when reading fast some log file because the user would read "device"
and think that a device is manipulated when it's in fact a node name.
Documentation of 1 make it pretty clear what to do for the user.
Kevin argued that all bs are node including devices ones so 2 does not make
sense.
Kevin also argued that rewriting the QMP block interface would not make disapear
the current one.
Kevin pushed the argument that making the QAPI generator compatible with the
semantic of the operation would need a rewrite that no one has done yet.
A vote has been done on the list to elect the version to use and 1 won.
For reference the complete thread is:
"[Qemu-devel] [PATCH V4 4/7] qmp: Allow to change password on names block driver
states."
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add the minimum of code to prepare for the following patches.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a common function for opening images to be used for block drivers
specified through BlockdevRefs in an option QDict. The difference from
bdrv_file_open() is that this function may invoke bdrv_open() instead,
allowing auto-detection of the driver to be used; and second, it
automatically extracts the BlockdevRef from the option QDict.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow specifying a reference to an existing block device (by name) for
bdrv_file_open() instead of a filename and/or options.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function basically parses command-line options given as a QDict
replacing a config file.
For instance, the QDict {"section.opt1": 42, "section.opt2": 23}
corresponds to the config file:
[section]
opt1 = 42
opt2 = 23
It is possible to specify multiple sections and also multiple sections
of the same type. On the command line, this looks like the following:
inject-error.0.event=reftable_load,\
inject-error.1.event=l2_load,\
set-state.event=l1_update
This would correspond to the following config file:
[inject-error "inject-error.0"]
event = reftable_load
[inject-error "inject-error.1"]
event = l2_load
[set-state]
event = l1_update
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function splits a QDict consisting of entries prefixed by
incrementally enumerated indices into a QList of QDicts.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Autocomplete qemu-io commands at the interactive prompt.
Note this only completes command names and not their options.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Using stdin with readline.c requires disabling echo and line buffering.
Add a portable wrapper to set the terminal attributes under Linux and
Windows.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Now that the monitor and readline are decoupled, readline.h no longer
belongs in include/monitor/. Put the header into include/qemu/.
Move the source file into util/ so it can be linked as part of
libqemuutil.a.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Make the readline.c functionality reusable. Instead of calling
monitor_printf() and monitor_flush() directly, invoke function pointers
provided by the user.
This way readline.c does not know about Monitor and other users will be
able to make use of readline.c.
Note that there is already an "opaque" argument to the ReadLineFunc
callback. Consistently call it "readline_opaque" from now on to
distinguish from the ReadLinePrintfFunc/ReadLineFlushFunc "opaque"
argument.
I also dropped the printf macro trickery since it's now highly unlikely
that anyone modifying readline.c would call printf(3) directly. We no
longer need this protection.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an sclp event for "cpu was hot plugged". This allows Qemu to deliver an
SCLP interrupt to the guest stating that the requested cpu hotplug was
completed.
Signed-off-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Implement the CPU data in SCLP "Read SCP Info". And implement "Read CPU Info"
SCLP command. This data will be used by the guest to get information about hot
plugged cpus.
Signed-off-by: Jason J. Herne <jjherne@us.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Define new SCLP codes to improve code readability.
Signed-off-by: Jason J. Herne <jjherne@us.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
There is a HOST_PAGE_ALIGN macro which makes sense for KVM accelerator
but it uses qemu_host_page_size/qemu_host_page_mask which initialized
for TCG only.
This moves qemu_host_page_size/qemu_host_page_mask initialization from
TCG's page_init() and adds a call for it from kvm_init().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds support for special usb descriptors used by microsoft
windows. They allow more fine-grained control over driver binding and
adding entries to the registry for configuration.
As this is a guest-visible change the "msos-desc" compat property
has been added to turn this off for 1.7 + older
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
cpu_physical_memory_set_dirty_lebitmap calls getpageaddr and ffsl which are
unavailable for MinGW. As the function is unused for MinGW, it can simply
be excluded from compilation.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If bitmaps are aligned properly, use bitmap operations. If they are
not, just use old bit at a time code.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
We want to have all the functions that handle directly the dirty
bitmap near. We will change it later.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
All the functions that use ram_addr_t should be here.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
We have an end parameter in all the callers, and this make it coherent
with the rest of cpu_physical_memory_* functions, that also take a
length parameter.
Once here, move the start/end calculation to
tlb_reset_dirty_range_all() as we don't need it here anymore.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
All uses except one really want the other meaning.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
We were clearing a range of bits, so use bitmap_clear().
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
We were setting a range of bits, so use bitmap_set().
Note: xen has always been wrong, and should have used start instead
of addr from the beginning.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
This operation is way faster than doing it bit by bit.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Now all functions use the same wording that bitops/bitmap operations
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
And make cpu_physical_memory_get_dirty_flag() to use it. It used to
be the other way around.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
After all the previous patches, spliting the bitmap gets direct.
Note: For some reason, I have to move DIRTY_MEMORY_* definitions to
the beginning of memory.h to make compilation work.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
For historical reasons it was bit 3. Once there, create a constant to
know the number of clients.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Document it
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
So remove the flag argument and do it directly. After this change,
there is nothing else using cpu_physical_memory_set_dirty_flags() so
remove it.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
So cpu_physical_memory_get_dirty_flags is not needed anymore
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
So return void.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Move index and size fields from int to long. We need that for
migration. long is 64 bits on sane architectures, and 32bits should
be enough on all the 32bits architectures.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
The VMState code will be moved to vmstate.c and it uses some of the
QEMU_VM_* constants, so move it to a header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The QEMUFile code will be moved to qemu-file.c. This will require making
the following functions non-static because they are used by the savevm.c
code:
* qemu_peek_byte()
* qemu_peek_buffer()
* qemu_file_skip()
* qemu_file_set_error()
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
* stefanha/block:
commit: Remove unused check
qemu-iotests: Update test cases for commit active
commit: Support commit active layer
block: Add commit_active_start()
mirror: Move base to MirrorBlockJob
mirror: Don't close target
qemu-iotests: drop duplicate virtio-blk initialization failure
vmdk: Allow vmdk_create to work with protocol
vmdk: Check VMFS extent line field number
docs: updated qemu-img man page and qemu-doc to reflect VHDX support.
block: vhdx - improve error message, and .bdrv_check implementation
block/iscsi: Fix compilation for libiscsi 1.4.0 (API change)
qapi-schema: fix QEMU 1.8 references
dataplane: replace hostmem with memory_region_find
dataplane: change vring API to use VirtQueueElement
vring: factor common code for error exits
vring: create a common function to parse descriptors
sheepdog: fix dynamic grow for running qcow2 format
Message-id: 1387554416-5837-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSuF+2AAoJECgfDbjSjVRpTz0IAJhNCC8L2GVt+pm1RAt6lbqZ
u9bCrqfThDORN2mUTEuLu4ZpZC0DYc7d0Jjr5NPesC5G/Afzi5/to6+l7nNZneU3
OdBPglXCCfU/cRaLu7JG2akpha0GVU0tsSCoWIYa6mwlWA4/DXVMgeKg/bh/EgfM
B1w4fE2RgRM9bEqWmX4+tZw8dgk7uVJhu95HCDnb5eikaKlFzwuOlvexrDV3KbPc
bkJe35zbGrKOws93tiSeoqcDx2dcYSzecPoJ0jiCY0KXJ17PBWAvuLTtYqkwwe9J
2FEnTslQJ3Rc8jTFiOPWx2pGaejG4y7Tnk6uuzW6fbbSLOQDPJy3KgmutJFMt1A=
=ShCj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi,pci,pc,fedora,virtio fixes and enhancements
This includes some Preparatory patches for cpu hotplug for q25 and memory
hotplug by Igor, tests and memory mapping change
by Laszlo and pci reset cleanup by Paolo.
There are also some fixes for fedora and virtio:
included here since they are test blockers for me.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 23 Dec 2013 08:07:18 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony:
target-arm: fix build with gcc 4.8.2
virtio: add back call to virtio_bus_device_unplugged
piix: fix 32bit pci hole
qdev: switch reset to post-order
qdev: allow both pre- and post-order vists in qdev walking functions
pci: clean up resetting of IRQs
pci: do not export pci_bus_reset
ACPI/DSDT-CPU: cleanup bogus comment
ACPI: Q35 DSDT: fix CPU hotplug GPE0.2 handler
acpi: ich9: allow guest to clear SCI rised by GPE
acpi: factor out common pm_update_sci() into acpi core
acpi: piix4: remove not needed GPE0 mask
i440fx-test: verify firmware under 4G and 1M, both -bios and -pflash
i440fx-test: generate temporary firmware blob
i440fx-test: give each GTest case its own qtest
i440fx-test: qtest_start() should be paired with qtest_end()
hw/i386/pc_sysfw: support two flash drives
pc_piix: document gigabyte_align
piix: gigabyte alignment for ram
Message-id: 1387815007-1272-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WrhM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'afaerber/tags/qom-devices-for-anthony' into staging
QOM infrastructure fixes and device conversions
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
# gpg: Signature made Tue 24 Dec 2013 09:04:05 AM PST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 174F 0347 1BCC 221A 6175 6F96 FA2E D12D 3E7E 013F
* afaerber/tags/qom-devices-for-anthony: (24 commits)
qdev-monitor: Improve error message for -device nonexistant
ioapic: QOM'ify ioapic
ioapic: Cleanup for QOM'ification
icc_bus: QOM'ify ICC
apic: QOM'ify APIC
apic: Cleanup for QOM'ification
qdev: Drop misleading qbus_free() function
qom: Detect bad reentrance during object_class_foreach()
tests: Test QOM interface casting
qom: Do not register interface "types" in the type table and fix names
qom: Split out object and class caches
qdev: Document that pointer properties kill device_add
hw: cannot_instantiate_with_device_add_yet due to pointer props
qdev-monitor: Avoid device_add crashing on non-device driver name
qdev: Do not let the user try to device_add when it cannot work
isa: Clean up use of cannot_instantiate_with_device_add_yet
vt82c686: Clean up use of cannot_instantiate_with_device_add_yet
piix3 piix4: Clean up use of cannot_instantiate_with_device_add_yet
ich9: Document why cannot_instantiate_with_device_add_yet
pci-host: Consistently set cannot_instantiate_with_device_add_yet
...
* mjt/trivial-patches:
acpi unit-test: Remove temporary disk after test
mainstone: Fix duplicate array values for key 'space'
pxa27x: Add 'const' attribute to keyboard maps
pxa27x: Reduce size of keyboard matrix mapping
doc: Mention chardev:id in available devices for -serial
configure: Python tests must be done before help message
configure: Rewrite code for help message
fix -boot strict regressed in commit 6ef4716
vl: make boot_strict variable static (not used outside vl.c)
x86: only allow real mode to access 32bit without LMA
linux-user: Use macro TARGET_NSIG_WORDS where possible
exynos4210: Use macro ARRAY_SIZE where possible
ui/cocoa: Use macro ARRAY_SIZE where possible
misc: Use macro ARRAY_SIZE where possible
openrisc: Fix spelling in comment (transaltion -> translation)
hw/arm/highbank: Simplify code (memory region in device state)
Message-id: 1388182050-10270-1-git-send-email-mjt@msgid.tls.msk.ru
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
IEEE754-2008 specifies a new rounding mode:
"roundTiesToAway: the floating-point number nearest to the infinitely
precise result shall be delivered; if the two nearest floating-point
numbers bracketing an unrepresentable infinitely precise result are
equally near, the one with larger magnitude shall be delivered."
Implement this new mode (it is needed for ARM). The general principle
is that the required code is exactly like the ties-to-even code,
except that we do not need to do the "in case of exact tie clear LSB
to round-to-even", because the rounding operation naturally causes
the exact tie to round up in magnitude.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Add the conversion functions float16_to_float64() and
float64_to_float16(), which will be needed for the ARM
A64 instruction set.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tidy up the get/set accessors for the fp state to add missing ones
and make them all inline in softfloat.h rather than some inline and
some not.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
This patch adds the float32_to_uint64() routine, which converts a
32-bit floating point number to an unsigned 64 bit number.
This contribution can be licensed under either the softfloat-2a or -2b
license.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: removed harmless but silly int64_t casts]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Currently the int-to-float functions take types which are specified
as "at least X bits wide", rather than "exactly X bits wide". This is
confusing and unhelpful since it means that the callers have to include
an explicit cast to [u]intXX_t to ensure the correct behaviour. Fix
them all to take the exactly-X-bits-wide types instead.
Note that this doesn't change behaviour at all since at the moment
we happen to define the 'int32' and 'uint32' types as exactly 32 bits
wide, and the 'int64' and 'uint64' types as exactly 64 bits wide.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Add the float to 16 bit integer conversion routines. These can be
trivially implemented in terms of the int32_to_float* routines, but
providing them makes our API more symmetrical and can simplify callers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
ARMv8 requires support for converting 32 and 64bit floating point
values to signed and unsigned 16bit integers.
Signed-off-by: Will Newton <will.newton@linaro.org>
[PMM: updated not to incorrectly set Inexact for Invalid inputs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
TRIGGER can really mean mean anything (e.g. was it triggered, is it
level-triggered, is it edge-triggered, etc.). Rename to EDGE_TRIGGER to
make the code comprehensible without looking up the data structure.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1387606179-22709-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is no longer needed, and is obsoleted by error_abort. Remove.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
This is a boiler-plate _nofail variant of qemu_opts_create. Remove and
use error_abort in call sites.
null/0 arguments needs to be added for the id and fail_if_exists fields
in affected callsites due to argument inconsistency between the normal and
no_fail variants.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Replace assert_no_error() usages with the error_abort system.
&error_abort is passed into API calls to signal to the Error sub-system
that any errors are fatal. Removes need for caller assertions.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Add a special Error * that can be passed to error handling APIs to
signal that any errors are fatal and should abort QEMU. There are two
advantages to this:
- allows for brevity when wishing to assert success of Error **
accepting APIs. No need for this pattern:
Error * local_err = NULL;
api_call(foo, bar, &local_err);
assert_no_error(local_err);
This also removes the need for _nofail variants of APIs with
asserting call sites now reduced to 1LOC.
- SIGABRT happens from within the offending API. When a fatal error
occurs in an API call (when the caller is asserting sucess) failure
often means the API itself is broken. With the abort happening in the
API call now, the stack frames into the call are available at debug
time. In the assert_no_error scheme the abort happens after the fact.
The exact semantic is that when an error is raised, if the argument
Error ** matches &error_abort, then the abort occurs immediately. The
error messaged is reported.
For error_propagate, if the destination error is &error_abort, then
the abort happens at propagation time.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Add two commands that are the monitor counterparts of -object. The commands
have the same Visitor-based implementation, but use different kinds of
visitors so that the HMP command has a DWIM string-based syntax, while
the QMP variant accepts a stricter JSON-based properties dictionary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
The mapping is a hardware feature, so it is relatively constant.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The row and column values use only a very limited range (-1 ... 7),
so a byte value is sufficient.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Convert 'init' function to QOM's 'realize' for ioapic and kvm-ioapic.
Change variable 'ioapic_no' from static to global. Then we can drop
the 'instance_no' function argument.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Convert 'init' function to QOM's 'realize' for apic, kvm/apic and
xen/xen_apic.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Same reasoning as commit 02a5c4c974
("qdev: Drop misleading qdev_free() function"). The qbus_free()
function removes the child from the namespace and decrements the
reference count. It does not, however, guarantee to free the child
since the refcount may still be held.
Just call object_unparent() directly.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
There should be no need to look up nor enumerate the interface "types",
whose "classes" are really just vtables. Just create the types and
add them to the interface list of the parent type.
Interfaces not registering their type anymore means that accessing
superclass::interface by type name will fail when initializing
subclass::interface. Thus, we need to pre-initialize the subclass's
parent_type field before calling type_initialize. Apart from this, the
interface "types" should never be used and thus it is harmless to leave
them out of the hashtable.
Further, the interface types had a bug with interfaces that are
inherited from a superclass: The implementation type name was wrong
(for example it was subclass::superclass::interface rather than
just subclass::interface). This patch fixes this as well.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The object-cast and class-cast caches cannot be shared because class
caching is conditional on the target type not being an interface and
object caching is unconditional. Leads to a bug when a class cast
to an interface follows an object cast to the same interface type:
FooObject = FOO(obj);
FooClass = FOO_GET_CLASS(obj);
Where TYPE_FOO is an interface. The first (object) cast will be
successful and cache the casting result (i.e. TYPE_FOO will be cached).
The second (class) cast will then check the shared cast cache
and register a hit. The issue is, when a class cast hits in the cache
it just returns a pointer cast of the input class (i.e. the concrete
class).
When casting to an interface, the cast itself must return the
interface class, not the concrete class. The implementation of class
cast caching already ensures that the returned cast result is only
a pointer cast before caching. The object cast logic however does
not have this check.
Resolve by just splitting the object and class caches.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Nathan Rossi <nathan.rossi@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Ask users of DEFINE_PROP_PTR() to set
cannot_instantiate_with_device_add_yet, or explain why it's not
needed.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Make the 32bit pci hole start at end of ram, so all possible address
space is covered.
We used to try and make addresses aligned so they are easier to cover
with MTRRs, but since they are cosmetic on KVM, this is probably not
worth worrying about.
Of course the firmware can use less than that. Leaving space unused is
no problem, mapping pci bars outside the hole causes problems though.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Post-order is the only sensible direction for the reset signals.
For example, suppose pre-order is used and the parent has some data
structures that cache children state (for example a list of active
requests). When the reset method is invoked on the parent, these caches
could be in any state.
If post-order is used, on the other hand, these will be in a known state
when the reset method is invoked on the parent.
This change means that it is no longer possible to block the visit of
the devices, so the callback is changed to return void. This is not
a problem, because PCI was returning 1 exactly in order to achieve the
same ordering that this patch implements.
PCI can then rely on the qdev core having sent a "reset signal" (whatever
that means) to the device, and only do the PCI-specific initialization
with pci_do_device_reset.
MST: fixed up virtio-ccw
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Resetting should be done in post-order, not pre-order. However,
qdev_walk_children and qbus_walk_children do not allow this. Fix
it by adding two extra arguments to the functions.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qbus_reset_all can be used instead. There is no semantic change
because pcibus_reset returns 1 and takes care of the device
tree traversal.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
... and rename it into acpi_update_sci() since it changes
SCI on only on PM registers status.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
commit_active_start is implemented in block/mirror.c, It will create a
job with "commit" type and designated base in block-commit command. This
will be used for committing active layer of device.
Sync mode is removed from MirrorBlockJob because there's no proper type
for commit. The used information is is_none_mode.
The common part of mirror_start and commit_active_start is moved to
mirror_start_job().
Fix the comment wording for commit_start.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Looking at the implementation, this doesn't really have a lot to do
with arrays. Its just a pointer to a buffer and is passed through
to the wrapped fn (qemu_fdt_setprop) unchanged. So rename to make it
consistent with libfdt, which in the wrapped function just calls it
"val".
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The qemu_devtree API is a wrapper around the fdt_ set of APIs.
Rename accordingly.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[agraf: also convert hw/arm/virt.c]
Signed-off-by: Alexander Graf <agraf@suse.de>
We use the rom infrastructure to write firmware and/or initial kernel
blobs into guest address space. So we're basically emulating the cache
off phase on very early system bootup.
That phase is usually responsible for clearing the instruction cache for
anything it writes into cachable memory, to ensure that after reboot we
don't happen to execute stale bits from the instruction cache.
So we need to invalidate the icache every time we write a rom into guest
address space. We do not need to do this for every DMA since the guest
expects it has to flush the icache manually in that case.
This fixes random reboot issues on e5500 (booke ppc) for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds very basic handlers for ibm,get-system-parameter and
ibm,set-system-parameter RTAS calls.
The only parameter handled at the moment is
"platform-processor-diagnostics-run-mode" which is always disabled and
does not support changing. This is expected to make
"ppc64_cpu --run-mode=1" happy.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[agraf: s/papameter/parameter/g]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for defining a vmstate field which is an array
of pointers to structures, and use this to define a
VMSTATE_PTIMER_ARRAY() which allows an array of ptimer_state*
to be used by devices.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1387159292-10436-2-git-send-email-lig.fnst@cn.fujitsu.com
DIGIC is Canon Inc.'s name for a family of SoC
for digital cameras and camcorders.
There is no publicly available specification for
DIGIC chips. All information about DIGIC chip
internals is based on reverse engineering efforts
made by CHDK (http://chdk.wikia.com) and
Magic Lantern (http://www.magiclantern.fm) projects
contributors.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1387188908-754-2-git-send-email-antonynpavlov@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
this patch introduces wrappers for the clrsb builtins,
which count the leading redundant sign bits.
Signed-off-by: Claudio Fontana <claudio.fontana@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Teach the chardev frontend to send event. This is used by the Spice port
chardev currently.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most notably this includes changes to exec to support
full 64 bit addresses.
This also flushes out patches that got queued during 1.7 freeze.
There are new tests, and a bunch of bug fixes all over the place.
There are also some changes mostly useful for downstreams.
I'm also listing myself as pc co-maintainer. I'm doing this reluctantly,
but this seems to be necessary to make sure patches are not lost or delayed too
much, and posting the MAINTAINERS patch did not seem to make anyone else
volunteer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSqK0/AAoJECgfDbjSjVRpz0wH/2BCUmgQ8oZfe9PrRhdCpYbw
6RtDLVucIUNq3CYfeV+Lua1Dw62CPVNGUR1Y2sk9s5X0C/lHLXeUkZxYy0JezGmW
k0EZAcVC4kXqyPbVh83I2pKtTwLGfI6I1qzsLZc+6CDT34YN7Lwe+wRJXQQNGcJc
gEbe4U8xuufdPZO2zv9RWEwmI4tI38PxnDJw+MYNJOKNnweLBRKq10YEKrref7Ml
4O1GxAXfQd0wkAhr9Cm7ZBajOzy/ovLj/b7HmiCMOvGkOaVhzurqbOtxlsbVIF9T
26+HEhu+2H/NO4qk5VmZjSngayUySBdEbGLHiovd8Xl4zMFPFNfQXv1mR3Vzb20=
=GPZ/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
acpi.pci,pc,memory core fixes
Most notably this includes changes to exec to support
full 64 bit addresses.
This also flushes out patches that got queued during 1.7 freeze.
There are new tests, and a bunch of bug fixes all over the place.
There are also some changes mostly useful for downstreams.
I'm also listing myself as pc co-maintainer. I'm doing this reluctantly,
but this seems to be necessary to make sure patches are not lost or delayed too
much, and posting the MAINTAINERS patch did not seem to make anyone else
volunteer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 11 Dec 2013 10:21:51 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (14) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony: (28 commits)
pc: use macro for HPET type
hpet: fix build with CONFIG_HPET off
acpi unit-test: adjust the test data structure for better handling
acpi unit-test: load and check facs table
exec: separate sections and nodes per address space
memory.c: bugfix - ref counting mismatch in memory_region_find
hpet: enable to entitle more irq pins for hpet
hpet: inverse polarity when pin above ISA_NUM_IRQS
pci: fix pci bridge fw path
ACPI DSDT: Make control method `IQCR` serialized
acpi: strip compiler info in built-in DSDT
acpi unit-test: verify signature and checksum
smbios: Set system manufacturer, product & version by default
exec: reduce L2_PAGE_SIZE
exec: make address spaces 64-bit wide
exec: memory radix tree page level compression
exec: pass hw address to phys_page_find
exec: extend skip field to 6 bit, page entry to 32 bit
exec: replace leaf with skip
split definitions for exec.c and translate-all.c radix trees
...
Message-id: cover.1386786228.git.mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
make hpet_find inline so we don't need
to build hpet.c to check if hpet is enabled.
Fixes link error with CONFIG_HPET off.
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Owning to some different hardware design, piix and q35 need
different compat. So making them diverge.
On q35, IRQ2/8 can be reserved for hpet timer 0/1. And pin 16~23
can be assigned to hpet as guest chooses. So we introduce intcap
property to do that.
Consider the compat and piix/q35, we finally have the following
value for intcap: For piix, hpet's intcap is hard coded as IRQ2.
For pc-q35-1.7 and earlier, we use IRQ2 for compat reason. Otherwise
IRQ2, IRQ8, and IRQ16~23 are allowed.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add floatnn_minnum() and floatnn_maxnum() functions which are equivalent
to the minNum() and maxNum() functions from IEEE 754-2008. They are
similar to min() and max() but differ in the handling of QNaN arguments.
Signed-off-by: Will Newton <will.newton@linaro.org>
Message-id: 1386158099-9239-5-git-send-email-will.newton@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If no fdt is provided on command line and the new field
get_dtb in struct arm_boot_info is set then call it to
get a device tree blob.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1385140638-10444-4-git-send-email-peter.maydell@linaro.org
[PMM: minor tweaks and cleanup]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the global timer to A9 MPCore.
Signed-off-by: François LEGAL <devel@thom.fr.eu.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: ff92f35f438ac671b57d99d823723dd3e62d2c49.1385969450.git.peter.crosthwaite@xilinx.com
[PC Changes:
* new commit message
* split off original version as a separate patch
* Rebased against new mpcore implementation (with struct embedding)
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM A9 MPCore has a timer that is global to all cores in the cluster.
The timer is shared but each core has a private independent comparator
and interrupt.
Based on version contributed by Francois LEGAL.
Signed-off-by: François LEGAL <devel@thom.fr.eu.org>
Message-id: 4918e89476b8da916be2964ec41578b50d569a37.1385969450.git.peter.crosthwaite@xilinx.com
[PC changes:
* New commit message
* Re-implemented as single timer model
* Fixed backwards counting issue in polled mode
* completed VMSD fields
* macroified magic numbers (and headerified reg definitions)
* split of as device-model-only patch
* use bitops for 64 bit register access
* Fixed auto increment mode to check condition properly
* general cleanup (names/style etc).
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[PMM:
* minor typo fixes
* added missing return after error_setg()
* dropped setting dc->no_user = 1
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To make it consistent for easier code reading. The order in which
variables are defined and functions are called is set to match the
address map ordering.
The new consistent order of doing stuff is:
SCU -> GIC -> MPTimer -> WDT.
0 functional change.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 8f31398e6d9a93f57291399f269039da1a77a2b5.1385969450.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we get SeaBIOS defaults: manufacturer Bochs, product Bochs,
no version. Best SeaBIOS can do, but we can provide better defaults:
manufacturer QEMU, product & version taken from QEMUMachine desc and
name.
Take care to do this only for new machine types, of course.
Note: Michael Tsirkin doesn't trust us to keep values of QEMUMachine member
product stable in the future. Use copies instead, and in a way that
makes it obvious that they're guest ABI.
Note that we can be trusted to keep values of member name, because
that has always been ABI.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qtest uses the icount infrastructure to implement a test-driven vm_clock. This
however is not necessary when using -qtest as a "probe" together with a normal
TCG-, KVM- or Xen-based virtual machine. Hence, split out the call to
configure_icount into a new function that is called only for "-machine
accel=qtest"; and disable those commands when running with an accelerator
other than qtest.
This also fixes an assertion failure with "qemu-system-x86_64 -machine
accel=qtest" but no -qtest option. This is a valid case, albeit somewhat
weird; nothing will happen in the VM but you'll still be able to
interact with the monitor or the GUI.
Now that qtest_init is not limited to an int(void) function, change
global variables that are not used outside qtest_init to arguments.
And finally, cleanup useless parts of include/sysemu/qtest.h. The file
is not used at all for user-only emulation, and qtest is not available
on Win32 due to its usage of sigwait.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
With a help of negative memory region priority PCI address space
is mapped underneath RAM regions effectively catching every access
to addresses not mapped by any other region.
It simplifies PCI address space mapping into system address space.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Put it in QEMUMachineInitArgs, so I don't have to touch every board.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Temporarily allow either VirtioDeviceClass::init or
VirtioDeviceClass::realize.
Introduce VirtioDeviceClass::unrealize for symmetry.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This ensures hot-unplug is handled properly by the proxy, and avoids
leaking bus_name which is freed by virtio_device_exit.
Cc: qemu-stable@nongnu.org
Acked-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now we have these pairs:
- virtio_bus_plug_device/virtio_bus_destroy_device. The first
takes a VirtIODevice, the second takes a VirtioBusState
- device_plugged/device_unplug callbacks in the VirtioBusClass
(here it's just the naming that is inconsistent)
- virtio_bus_destroy_device is not called by anyone (and since
it calls qdev_free, it would be called by the proxies---but
then the callback is useless since the proxies can do whatever
they want before calling virtio_bus_destroy_device)
And there is a k->init but no k->exit, hence virtio_device_exit is
overwritten by subclasses (except virtio-9p). This cleans it up by:
- renaming the device_unplug callback to device_unplugged
- renaming virtio_bus_plug_device to virtio_bus_device_plugged,
matching the callback name
- renaming virtio_bus_destroy_device to virtio_bus_device_unplugged,
removing the qdev_free, making it take a VirtIODevice and calling it
from virtio_device_exit
- adding a k->exit callback
virtio_device_exit is still overwritten, the next patches will fix that.
Cc: qemu-stable@nongnu.org
Acked-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The vdev field is complicated to synchronize. Just access the
BusState's list of children.
Cc: qemu-stable@nongnu.org
Acked-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Paolo Bonzini (17) and others
# Via Stefan Hajnoczi
* stefanha/block: (48 commits)
qemu-iotests: filter QEMU monitor \r\n
aio: make aio_poll(ctx, true) block with no fds
block: clean up bdrv_drain_all() throttling comments
qcow2: use start_of_cluster() and offset_into_cluster() everywhere
qemu-img: decrease progress update interval on convert
qemu-img: round down request length to an aligned sector
qemu-img: dynamically adjust iobuffer size during convert
block/iscsi: set bs->bl.opt_transfer_length
block: add opt_transfer_length to BlockLimits
block/iscsi: set bdi->cluster_size
qemu-img: fix usage instruction for qemu-img convert
qemu-img: add support for skipping zeroes in input during convert
qemu-nbd: add doc for option -f
qemu-iotests: add test for snapshot in qemu-img convert
qemu-img: add -l for snapshot in convert
qemu-iotests: add 058 internal snapshot export with qemu-nbd case
qemu-nbd: support internal snapshot export
snapshot: distinguish id and name in load_tmp
qemu-iotests: Split qcow2 only cases in 048
qemu-iotests: Clean up spaces in usage output
...
Message-id: 1386347807-27359-1-git-send-email-stefanha@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=uEdP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kwolf/tags/for-anthony' into staging
Block patches for 2.0 (flushing block-next)
# gpg: Signature made Fri 29 Nov 2013 08:43:18 AM PST using RSA key ID C88F2FD6
# gpg: Can't check signature: public key not found
# By Peter Lieven (17) and others
# Via Kevin Wolf
* kwolf/tags/for-anthony: (41 commits)
qemu-iotests: Add sample image and test for VMDK version 3
vmdk: Allow read only open of VMDK version 3
qemu-iotests: Filter out 'qemu-io> ' prompt
qemu-iotests: Filter qemu-io output in 025
block: Use BDRV_O_NO_BACKING where appropriate
qemu-iotests: Test snapshot mode
block: Enable BDRV_O_SNAPSHOT with driver-specific options
qemu-iotests: Make test case 030, 040 and 055 deterministic
qemu-iotest: Add pause_drive and resume_drive methods
blkdebug: add "remove_break" command
qemu-iotests: Drop local version of cancel_and_wait from 040
sheepdog: support user-defined redundancy option
sheepdog: refactor do_sd_create()
qdict: Optimise qdict_do_flatten()
qdict: Fix memory leak in qdict_do_flatten()
MAINTAINERS: add sheepdog development mailing list
COW: Extend checking allocated bits to beyond one sector
COW: Speed up writes
qapi: Change BlockDirtyInfo to list
block: per caller dirty bitmap
...
Message-id: 1385743555-27888-1-git-send-email-kwolf@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Paul Durrant (1) and Wei Liu (1)
# Via Stefano Stabellini
* sstabellini/xen-2013-12-01:
xen-pvdevice: make device-id property compulsory
xen: fix two errors when debug is enabled
Message-id: alpine.DEB.2.02.1312011829000.3198@kaball.uk.xensource.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Richard Henderson
# Via Richard Henderson
* rth/auxv-2:
linux-user: Use qemu_getauxval for AT_EXECFD
util: Use qemu_getauxval in linux qemu_cache_utils_init
tcg-s390: Use qemu_getauxval in query_facilities
tcg-arm: Use qemu_getauxval
tcg-ppc64: Use qemu_getauxval
osdep: Create qemu_getauxval and qemu_init_auxval
Message-id: 1385757754-10702-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Bugfixes for uas emulation.
Add remote wakeup support for ehci.
Add suspend support for xhci.
Misc minor tweaks and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=2yvC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kraxel/tags/pull-usb-1' into staging
Improvements for usb3 bulk stream (usb core, xhci).
Bugfixes for uas emulation.
Add remote wakeup support for ehci.
Add suspend support for xhci.
Misc minor tweaks and fixes.
# gpg: Signature made Thu 28 Nov 2013 11:44:49 PM PST using RSA key ID D3E87138
# gpg: Can't check signature: public key not found
# By Hans de Goede (11) and others
# Via Gerd Hoffmann
* kraxel/tags/pull-usb-1:
usb: move usb_{hi,lo} helpers to header file.
usb: add vendor request defines
trace-events: Clean up after removal of old usb-host code
Revert "usb-tablet: Don't claim wakeup capability for USB-2 version"
ehci: implement port wakeup
xhci: Call usb_device_alloc/free_streams
usb: Add usb_device_alloc/free_streams
usb: Add max_streams attribute to endpoint info
uas: s/ui/iu/
uas: Fix response iu struct definition
uas: Bounds check tags when using streams
uas: Streams are numbered 1-y, rather then 0-x
uas: Fix / cleanup usb_uas_task error handling
uas: Only use report iu-s for task_mgmt status reporting
scsi: Add 2 new sense codes needed by uas
xhci: add support for suspend/resume
xhci: Add a few missing checks for disconnected devices
Message-id: 1385712381-30918-1-git-send-email-kraxel@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Now it is possible to directly export an internal snapshot, which
can be used to probe the snapshot's contents without qemu-img
convert.
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Since later this function will be used so improve it. The only caller of it
now is qemu-img, and it is not impacted by introduce function
bdrv_snapshot_load_tmp_by_id_or_name() that call bdrv_snapshot_load_tmp()
twice to keep old search logic. bdrv_snapshot_load_tmp_by_id_or_name() return
int to let caller know the errno, and errno will be used later.
Also fix a typo in comments of bdrv_snapshot_delete().
Signed-off-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This will be used by the SCSI layer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This lets bdrv_co_do_rw receive flags, so that it can be used for
zero writes.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Most code already used QEMUTimer without the redundant 'struct' keyword.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This reduces the dependencies on trace.h.
Only two source files which need console.h also need trace.h.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The AioContext ctx field is apparently unused in qemu codebase since
02ffb50448.
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
qemu_co_queue_wait_insert_head() is unused in qemu code base now.
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The intention of the Xen PV device is that it is used as a parent
device for PV drivers in Xen HVM guests and the set of PV drivers that
bind to the device is determined by its device ID (and possibly
vendor ID and revision). As such, the device should not have a default
device ID, it should always be supplied by the Xen toolstack.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
With this we no longer pass down envp, and thus all systems can have
the same void prototype. So also eliminate a useless thunk.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
No need to set up a SIGILL signal handler for detection anymore.
Remove a ton of sanity checks that must be true, given that we're
requiring a 64-bit build (the note about 31-bit KVM is satisfied
by configuring with TCI).
Signed-off-by: Richard Henderson <rth@twiddle.net>
Allow host detection on linux systems without glibc 2.16 or later.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Allow host detection on linux systems without glibc 2.16 or later.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This adds "remove_break" command which is the reverse of blkdebug
command "break": it removes all breakpoints with given tag and resumes
all the requests.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Sheepdog support two kinds of redundancy, full replication and erasure coding.
# create a fully replicated vdi with x copies
-o redundancy=x (1 <= x <= SD_MAX_COPIES)
# create a erasure coded vdi with x data strips and y parity strips
-o redundancy=x:y (x must be one of {2,4,8,16} and 1 <= y < SD_EC_MAX_STRIP)
E.g, to convert a vdi into sheepdog vdi 'test' with 8:3 erasure coding scheme
$ qemu-img convert -o redundancy=8:3 linux-0.2.img sheepdog:test
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Liu Yuan <namei.unix@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We have multiple dirty bitmaps in BDS now, switch QAPI to allow query
it (BlockInfo.dirty_bitmaps), and also drop old BlockInfo.dirty.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Previously a BlockDriverState has only one dirty bitmap, so only one
caller (e.g. a block job) can keep track of writing. This changes the
dirty bitmap to a list and creates a BdrvDirtyBitmap for each caller, the
lifecycle is managed with these new functions:
bdrv_create_dirty_bitmap
bdrv_release_dirty_bitmap
Where BdrvDirtyBitmap is a linked list wrapper structure of HBitmap.
In place of bdrv_set_dirty_tracking, a BdrvDirtyBitmap pointer argument
is added to these functions, since each caller has its own dirty bitmap:
bdrv_get_dirty
bdrv_dirty_iter_init
bdrv_get_dirty_count
bdrv_set_dirty and bdrv_reset_dirty prototypes are unchanged but will
internally walk the list of all dirty bitmaps and set them one by one.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add defines for vendor specific usb control requests.
Group defines by Device / Interface / Endpoint while
being at it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
this patch adds a call to completely zero out a block device.
the operation is sped up by checking the block status and
only writing zeroes to the device if they currently do not
return zeroes. optionally the zero writing can be sped up
by setting the flag BDRV_REQ_MAY_UNMAP to emulate the zero
write by unmapping if the driver supports it.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
this patch adds BlockLimits which introduces discard and write_zeroes
limits and alignment information to the BlockDriverState.
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This adds 2 wrappers to read the unallocated_blocks_are_zero and
can_write_zeroes_with_unmap info from the BDI. The wrappers are
required to check for the existence of a backing_hd and
if the devices are opened with the correct flags.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Lieven <pl@kamp.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
clang defines __ATOMIC_SEQ_CST but its implementation of the
__atomic_exchange() builtin differs from that of gcc. Move the
__clang__ branch of the ifdef ladder to the top and fix its
implementation (there is no such builtin as __sync_exchange),
so we can compile with clang again.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This causes two slight backwards-incompatibilities between "-M pc-1.5"
and 1.5's "-M pc":
(1) a fw_cfg file is removed with this patch. This is only a problem
if migration stops the virtual machine exactly during fw_cfg enumeration.
(2) after migration, a VM created without an explicit "-device pvpanic"
will stop reporting panics to management.
The first problem only occurs if migration is done at a very, very
early point (and I'm not sure it can happen in practice for reasonable-size
VMs, since it will likely take more time to send the RAM to destination,
than it will take for BIOS to scan fw_cfg).
The second problem only occurs if the guest panics _and_ has a guest
driver _and_ management knows to look at the crash event, so it is
mostly theoretical at this point in time.
Thus keep the code simple, and pretend it was never broken.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently we have three QemuOptsList (qemu_common_drive_opts,
qemu_legacy_drive_opts, and qemu_drive_opts), only qemu_drive_opts
is added to vm_config_groups[].
This patch changes query-command-line-options to access three local
QemuOptsLists for drive option, and merge the description items
together.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This reverts PCI master abort support - we'll want it
eventually but it exposes too many core bugs to be safe for 1.7.
This also reverts a recent exec.c change that was an
attempt to work-around some of these core bugs.
Also included are small fixes in pc and virtio,
and a core loader fix for PPC bamboo.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSf4ZyAAoJECgfDbjSjVRp9DIIAK7yEMa9ie5n3sInKH+xHT3R
Sf4uErqx55WfT/54dnLJPrs7DTfXblW+Qjnq/7RuaoJ32Dfshgxz64mPF+Lm2s3+
ghjdQrKo2YkdSbbxy+AnBNO4eHMSeUs/rM2yIfi7FZU0nwC7wNe1QpAN3UjM4yAF
5vE18xZE0Rxz/prXgofLtPHa1czvGPFk1qbS7Vag6HCSkfEI4N1Jxf9otDRV6KZP
9hX0kTvZyOKdbhccN05G4VCWwx5YUrpBsNSoph4Jx1aokEBoucr4sgE1FPDp0H9H
bJqDaAM2G5HNrDtIiDov5WOzRNT/ly011Q4mcaQh3va0pqUXttKCHgE1KRgn76I=
=iMNW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, virtio bug fixes
This reverts PCI master abort support - we'll want it
eventually but it exposes too many core bugs to be safe for 1.7.
This also reverts a recent exec.c change that was an
attempt to work-around some of these core bugs.
Also included are small fixes in pc and virtio,
and a core loader fix for PPC bamboo.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 10 Nov 2013 05:13:22 AM PST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (3) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
Revert "exec: limit system memory size"
Revert "hw/pci: partially handle pci master abort"
loader: drop return value for rom_add_blob_fixed
acpi-build: disable with -no-acpi
virtio-net: only delete bh that existed
Fix pc migration from qemu <= 1.5
Message-id: 1384159176-31662-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This reverts commit a53ae8e934.
The patch being reverted introduced a low-priority memory region
covering all 64 bit pci address space. This exposed the following bugs
elsewhere in the code:
1. Some memory regions have INT64_MAX size, where the
intent was all 64 bit address space.
This results in a sub-page region, should be UINT64_MAX.
2. page table rendering in exec.c ignores physical address bits
above TARGET_PHYS_ADDR_SPACE_BITS.
Access outside this range (e.g. from device DMA, or gdb stub)
ends up with a wrong region. Registering a region outside this
range leads to page table corruption.
3. Some regions overlap PCI hole and have same priority.
This only works as long as no device uses the overlapping address.
It doesn't look like we can resolve all issues in time for 1.7.
Let's fix the bugs first and apply afterwards for 1.8.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
rom_add_blob never fails, and neither does rom_add_blob_fixed,
so there's no need to return value from it.
In fact, rom_add_blob_fixed was erroneously returning -1 unconditionally
which made the only system that checked the return value -M bamboo fail
to start.
Drop the return value and drop checks from ppc440_bamboo to
fix this failure.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The following commit introduced a migration incompatibility:
commit 568f0690fd
Author: David Gibson <david@gibson.dropbear.id.au>
Date: Thu Jun 6 18:48:49 2013 +1000
pci: Replace pci_find_domain() with more general pci_root_bus_path()
The issue is that i440fx savevm idstr went from 0000:00:00.0/I440FX to
0000:00.0/I440FX. Unfortunately we are stuck with the breakage for
1.6 machine types.
Add a compat property to maintain the busted idstr for the 1.6 machine
types, but revert to the old style format for 1.7+, and <= 1.5.
Tested with migration from qemu 1.5, qemu 1.6, and qemu.git.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[Assigning a multicast MAC address to a NIC leads to confusing behavior.
Reject multicast MAC addresses so users are alerted to their error
straight away.
The "net/eth.h" in6_addr rename prevents a name collision with
<netinet/in.h> on Linux.
-- Stefan]
Signed-off-by: Dmitry V. Krivenok <krivenok.dmitry@gmail.com>
Reviewed-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Replace the legacy cpu_to_32wu() with stl_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-10-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_be64wu() with stq_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-9-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_be32wu() with stl_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-8-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_be16wu() with stw_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-7-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy be32_to_cpupu() with ldl_be_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-6-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy le32_to_cpupu() with ldl_le_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-5-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy le16_to_cpupu() with lduw_le_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-4-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_le32wu() with stl_le_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-3-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Replace the legacy cpu_to_le16wu() with stw_le_p().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1383669517-25598-2-git-send-email-peter.maydell@linaro.org
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Turn PCMCIACardState into a device.
Move callbacks to new PCMCIACardClass.
Derive TYPE_MICRODRIVE from TYPE_PCMCIA_CARD.
Replace ide_init2_with_non_qdev_drives().
Signed-off-by: Othmar Pasteka <pasteka@kabsi.at>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The qdev_free() function name is misleading since all the function does
is unlink the device from its parent. The device is not necessarily
freed.
The device will be freed when its QObject refcount reaches zero. It is
usual for the parent (bus) to hold the final reference but there are
cases where something else holds a reference so "free" is a misleading
name.
Call object_unparent(obj) directly instead of having a qdev wrapper
function.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move state struct, type constant and cast macro to a new header.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move state struct, type constant and cast macro to a new header.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Rename NCPU to GIC_NCPU and move GICState away from gic_internal.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wGCx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'kwolf/tags/for-anthony' into staging
Block patches for 1.7.0-rc0 (v2)
# gpg: Signature made Thu 31 Oct 2013 04:44:39 PM CET using RSA key ID C88F2FD6
# gpg: Can't check signature: public key not found
* kwolf/tags/for-anthony: (30 commits)
vmdk: Implment bdrv_get_specific_info
qapi: Add optional field 'compressed' to ImageInfo
qemu-iotests: prefill some data to test image
sheepdog: check simultaneous create in resend_aioreq
sheepdog: cancel aio requests if possible
sheepdog: make add_aio_request and send_aioreq void functions
sheepdog: try to reconnect to sheepdog after network error
coroutine: add co_aio_sleep_ns() to allow sleep in block drivers
sheepdog: reload inode outside of resend_aioreq
sheepdog: handle vdi objects in resend_aio_req
sheepdog: check return values of qemu_co_recv/send correctly
qemu-iotests: Test case for backing file deletion
qemu-iotests: drop duplicated "create_image"
qemu-iotests: Fix 051 reference output
block: Avoid unecessary drv->bdrv_getlength() calls
block: Disable BDRV_O_COPY_ON_READ for the backing file
ahci: fix win7 hang on boot
sheepdog: pass copy_policy in the request
sheepdog: explicitly set copies as type uint8_t
block: Don't copy backing file name on error
...
Message-id: 1383064269-27720-1-git-send-email-kwolf@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
* agraf/ppc-for-upstream: (29 commits)
spapr: Use DeviceClass::fw_name for device tree CPU node
target-ppc: Fill in OpenFirmware names for some PowerPCCPU families
target-ppc: dump-guest-memory support
dump-guest-memory: Check for the correct return value
target-ppc: Use #define for max slb entries
target-ppc: Check for error on address translation in memsave command
target-ppc: Update slb array with correct index values.
spapr-pci: enable irqfd for INTx
xics-kvm: enable irqfd for MSI
xics: Implement H_XIRR_X
xics: Implement H_IPOLL
xics-kvm: Support for in-kernel XICS interrupt controller
xics: add cpu_setup callback
xics: split to xics and xics-common
xics: add missing const specifiers to TypeInfo
xics: convert init() to realize()
xics: add pre_save/post_load dispatchers
xics: replace fprintf with error_report
spapr: move cpu_setup after kvmppc_set_papr
xics: move reset and cpu_setup
...
Message-id: 1382736474-32128-1-git-send-email-agraf@suse.de
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSXNO8AAoJECgfDbjSjVRp7VAH/0B73mCOiyVACGx7fazK3SGK
X8TxZWVtG5A77ISqKyrtjLAhK9DCQjEzQTbMNhXHM3Ar6crwo7nJZnQvH2Gh1X2p
34BOQSVc4rtXz5pwDIr48dBLrxeslwXub79chUs+IK1/4RSn3h3nuS3k6JVkmLJN
rcHMj4ljJmi4Hd9vOpmS1jo/a61usi36hhU7CMgcrsXzStZycBBzCozOB3VW8p1X
/iwyf91YjmNPkn9gA3/aViGjszu8jE91dkA0C+ljwvcGbs2yEl3LCWEJfsMvoh5P
2M+k0XXbHwq/P9PFMa/2/lWOo4EO4Oxa+G/6QvovJrteYnktr+E9DqjU8pCT7yI=
=CVfs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pci, pc, acpi fixes, enhancements
This includes some pretty big changes:
- pci master abort support by Marcel
- pci IRQ API rework by Marcel
- acpi generation support by myself
Everything has gone through several revisions, latest versions have been on
list for a while without any more comments, tested by several
people.
Please pull for 1.7.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2013 07:33:48 AM CEST using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
* mst/tags/for_anthony: (39 commits)
ssdt-proc: update generated file
ssdt: fix PBLK length
i386: ACPI table generation code from seabios
pc: use new api to add builtin tables
acpi: add interface to access user-installed tables
hpet: add API to find it
pvpanic: add API to access io port
ich9: APIs for pc guest info
piix: APIs for pc guest info
acpi/piix: add macros for acpi property names
i386: define pc guest info
loader: allow adding ROMs in done callbacks
i386: add bios linker/loader
loader: use file path size from fw_cfg.h
acpi: ssdt pcihp: updat generated file
acpi: pre-compiled ASL files
acpi: add rules to compile ASL source
i386: add ACPI table files from seabios
q35: expose mmcfg size as a property
q35: use macro for MCFG property name
...
Message-id: 1381818560-18367-1-git-send-email-mst@redhat.com
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Commit 9b8c69243 (since reverted) broke the ability to boot the kernel
as the value returned by unassigned_mem_read returned non-zero and left
the kernel looping forever waiting for it to change (see
integrator_led_set in the kernel code).
Relying on a varying implementation detail is incorrect anyway so this
introduces a basic stub of a memory region for the debug/LED section
on the integrator board.
Signed-off-by: Alex Bennée <alex@bennee.com>
Message-id: 1382451366-9539-1-git-send-email-alex.bennee@linaro.org
[PMM: removed three unused fields from struct IntegratorDebugState]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This helper function behaves similarly to co_sleep_ns(), but the
sleeping coroutine will be resumed when using qemu_aio_wait().
Signed-off-by: MORITA Kazutaka <morita.kazutaka@lab.ntt.co.jp>
Tested-by: Liu Yuan <namei.unix@gmail.com>
Reviewed-by: Liu Yuan <namei.unix@gmail.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The block layer generally keeps the size of an image cached in
bs->total_sectors so that it doesn't have to perform expensive
operations to get the size whenever it needs it.
This doesn't work however when using a backend that can change its size
without qemu being aware of it, i.e. passthrough of removable media like
CD-ROMs or floppy disks. For this reason, the caching is disabled when a
removable device is used.
It is obvious that checking whether the _guest_ device has removable
media isn't the right thing to do when we want to know whether the size
of the host backend can change. To make things worse, non-top-level
BlockDriverStates never have any device attached, which makes qemu
assume they are removable, so drv->bdrv_getlength() is always called on
the protocol layer. In the case of raw-posix, this causes unnecessary
lseek() system calls, which turned out to be rather expensive.
This patch completely changes the logic and disables bs->total_sectors
caching only for certain block driver types, for which a size change is
expected: host_cdrom and host_floppy on POSIX, host_device on win32; also
the raw format in case it sits on top of one of these protocols, but in
the common case the nested bdrv_getlength() call on the protocol driver
will use the cache again and avoid an expensive drv->bdrv_getlength()
call.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of relying on cpu_model, obtain the device tree node label
per CPU. Use DeviceClass::fw_name as source.
Whenever DeviceClass::fw_name is unknown, default to "PowerPC,UNKNOWN".
As a consequence, spapr_fixup_cpu_dt() can operate on each CPU's fw_name,
obsoleting sPAPREnvironment::cpu_model, and spapr_create_fdt_skel() can
drop its cpu_model argument.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch add support for dumping guest memory using dump-guest-memory
monitor command.
Before patch:
(qemu) dump-guest-memory testcrash
this feature or command is not currently supported
(qemu)
After patch:
(qemu) dump-guest-memory testcrash
(qemu)
crash was able to read the file
crash> bt
PID: 0 TASK: c000000000c0d0d0 CPU: 0 COMMAND: "swapper/0"
R0: 0000000028000084 R1: c000000000cafa50 R2: c000000000cb05b0
R3: 0000000000000000 R4: c000000000bc4cb0 R5: 0000000000000000
R6: 001efe93b8000000 R7: 0000000000000000 R8: 0000000000000000
R9: b000000000001032 R10: 0000000000000001 R11: 0001eb2117e00d55
....
...
NOTE: Currently crash tools doesn't look at ELF notes in the dump on ppc64.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This implements H_XIRR_X hypercall in addition to H_XIRR as
it is mandatory for PAPR+ and there is no way for the guest to
detect whether it is supported or not so just add it.
As the Partition Adjunct Option is not supported at the moment,
the CPPR parameter of the hypercall is ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
Recent (host) kernels support emulating the PAPR defined "XICS" interrupt
controller system within KVM. This patch allows qemu to initialize and
configure the in-kernel XICS, and keep its state in sync with qemu's XICS
state as necessary.
This should give considerable performance improvements. e.g. on a simple
IPI ping-pong test between hardware threads, using qemu XICS gives us
around 5,000 irqs/second, whereas the in-kernel XICS gives us around
70,000 irqs/s on the same hardware configuration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[Mike Qiu <qiudayu@linux.vnet.ibm.com>: fixed mistype which caused ics_set_kvm_state() to fail]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds a cpu_setup callback to the XICS device class (as XICS-KVM
will do it different), xics_cpu_setup() will call it if it is set.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The upcoming XICS-KVM support will use bits of emulated XICS code.
So this introduces new level of hierarchy - "xics-common" class. Both
emulated XICS and XICS-KVM will inherit from it and override class
callbacks when required.
The new "xics-common" class implements:
1. replaces static "nr_irqs" and "nr_servers" properties with
the dynamic ones and adds callbacks to be executed when properties
are set.
2. xics_cpu_setup() callback renamed to xics_common_cpu_setup() as
it is a common part for both XICS'es
3. xics_reset() renamed to xics_common_reset() for the same reason.
The emulated XICS changes:
1. the part of xics_realize() which creates ICPs is moved to
the "nr_servers" property callback as realize() is too late to
create/initialize devices and instance_init() is too early to create
devices as the number of child devices comes via the "nr_servers"
property.
2. added ics_initfn() which does a little part of what xics_realize() did.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The upcoming support of in-kernel XICS will redefine migration callbacks
for both ICS and ICP so classes and callback pointers are added.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
On the real hardware, RTAS is called in real mode and therefore
top 4 bits of the address passed in the call are ignored.
So does the patch.
This converts h_rtas() to use existing rtas_ld() handlers.
This fixed rtas_ld()/rtas_st() to ignore top 4 bits.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
# By Paolo Bonzini (10) and others
# Via Paolo Bonzini
* bonzini/iommu-for-anthony:
exec: remove qemu_safe_ram_ptr
icount: make it thread-safe
icount: document (future) locking rules for icount
icount: prepare the code for future races in calling qemu_clock_warp
icount: reorganize icount_warp_rt
icount: use cpu_get_icount() directly
timer: add timer_mod_anticipate and timer_mod_anticipate_ns
timer: extract timer_mod_ns_locked and timerlist_rearm
timer: make qemu_clock_enable sync between disable and timer's cb
qemu-thread: add QemuEvent
timer: protect timers_state's clock with seqlock
seqlock: introduce read-write seqlock
vga: Mark relevant portio lists regions as coalesced MMIO flushing
cirrus: Mark vga io region as coalesced MMIO flushing
portio: Allow to mark portio lists as coalesced MMIO flushing
compatfd: switch to QemuThread
memory: fix 128 arithmetic in info mtree
Message-id: 1382024935-28297-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
These let a user anticipate the deadline of a timer, atomically with
other sites that call the function. This helps avoiding complicated
lock hierarchies.
Reviewed-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After disabling the QemuClock, we should make sure that no QemuTimers
are still in flight. To implement that with light overhead, we resort
to QemuEvent. The caller of disabling will wait on QemuEvent of each
timerlist.
Note, qemu_clock_enable(foo,false) can _not_ be called from timer's cb.
Also, the callers of qemu_clock_enable() should be protected by the BQL.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This emulates Win32 manual-reset events using futexes or conditional
variables. Typical ways to use them are with multi-producer,
single-consumer data structures, to test for a complex condition whose
elements come from different threads:
for (;;) {
qemu_event_reset(ev);
... test complex condition ...
if (condition is true) {
break;
}
qemu_event_wait(ev);
}
Or more efficiently (but with some duplication):
... evaluate condition ...
while (!condition) {
qemu_event_reset(ev);
... evaluate condition ...
if (!condition) {
qemu_event_wait(ev);
... evaluate condition ...
}
}
QemuEvent provides a very fast userspace path in the common case when
no other thread is waiting, or the event is not changing state.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
QEMU_CLOCK_VIRTUAL may be read outside BQL. This will make its
foundation, i.e. cpu_clock_offset exposed to race condition.
Using private lock to protect it.
After this patch, reading QEMU_CLOCK_VIRTUAL is thread safe
unless use_icount is true, in which case the existing callers
still rely on the BQL.
Lock rule: private lock innermost, ie BQL->"this lock"
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Seqlock implementation for QEMU. Usage idiom
reader:
do {
start = seqlock_read_begin(&sl);
...
} while (seqlock_read_retry(&sl, start));
writer:
seqlock_write_lock(&sl);
...
seqlock_write_unlock(&sl);
initialization:
seqlock_init(QemuSeqLock *sl, QemuMutex *mutex)
mutex could be NULL if the caller will provide its own protection
for concurrent write sides (typically using the BQL).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will enable us to remove all remaining explicit calls of
qemu_flush_coalesced_mmio_buffer in IO handlers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes spice display initialization to handle
multihead properly.
spice-core now keeps track of which QemuConsole has a spice
display channel attached to it and which has not. It also
manages display channel ids.
spice-display looks at all QemuConsoles and will pick up any
graphic console not yet bound to a spice channel (which in practice
are all non-qxl graphic devices).
Result is that
(a) you'll get a spice client window for each graphical device
now (first only without this patch), and
(b) mixing qxl and non-qxl vga cards works properly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
phys_mem_alloc and its assigned values qemu_anon_ram_alloc and
legacy_s390_alloc must have identical argument lists.
legacy_s390_alloc uses the size parameter to call mmap, so size_t is
good enough for all of them.
This patch fixes compiler errors on i686 Linux hosts:
CC alpha-softmmu/exec.o
exec.c:752:51: error:
initialization from incompatible pointer type [-Werror]
exec.c: In function 'qemu_ram_alloc_from_ptr':
exec.c:1139:32: error:
comparison of distinct pointer types lacks a cast [-Werror]
exec.c: In function 'qemu_ram_remap':
exec.c:1283:21: error:
comparison of distinct pointer types lacks a cast [-Werror]
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1380481005-32399-1-git-send-email-sw@weilnetz.de
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This adds C code for generating ACPI tables at runtime,
imported from seabios git tree
commit 51684b7ced75fb76776e8ee84833fcfb6ecf12dd
Although ACPI tables come from a system BIOS on real hw,
it makes sense that the ACPI tables are coupled with the
virtual machine, since they have to abstract the x86 machine to
the OS's.
This is widely desired as a way to avoid the churn
and proliferation of QEMU-specific interfaces
associated with ACPI tables in bios code.
Notes:
As BIOS can reprogram devices prior to loading
ACPI tables, we pre-format ACPI tables but defer loading
hardware configuration there until tables are loaded.
The code structure was intentionally kept as close
to the seabios original as possible, to simplify
comparison and making sure we didn't lose anything
in translation.
Minor code duplication results, to help ensure there are no functional
regressions, I think it's better to merge it like this and do more code
changes in follow-up patches.
Cross-version compatibility concerns have been addressed:
ACPI tables are exposed to guest as FW_CFG entries.
When running with -M 1.5 and older, this patch disables ACPI
table generation, and doesn't expose ACPI
tables to guest.
As table content is likely to change over time,
the following measures are taken to simplify
cross-version migration:
- All tables besides the RSDP are packed in a single FW CFG entry.
This entry size is currently 23K. We round it up to 64K
to avoid too much churn there.
- Tables are placed in special ROM blob (not mapped into guest memory)
which is automatically migrated together with the guest, same
as BIOS code.
- Offsets where hardware configuration is loaded in ACPI tables
are also migrated, this is in case future ACPI changes make us
rearrange the tables in memory.
This patch reuses some code from SeaBIOS, which was originally under
LGPLv2 and then relicensed to GPLv3 or LGPLv3, in QEMU under GPLv2+. This
relicensing has been acked by all contributors that had contributed to the
code since the v2->v3 relicense. ACKs approving the v2+ relicensing are
listed below. The list might include ACKs from people not holding
copyright on any parts of the reused code, but it's better to err on the
side of caution and include them.
Affected SeaBIOS files (GPLv2+ license headers added)
<http://thread.gmane.org/gmane.comp.bios.coreboot.seabios/5949>:
src/acpi-dsdt-cpu-hotplug.dsl
src/acpi-dsdt-dbug.dsl
src/acpi-dsdt-hpet.dsl
src/acpi-dsdt-isa.dsl
src/acpi-dsdt-pci-crs.dsl
src/acpi.c
src/acpi.h
src/ssdt-misc.dsl
src/ssdt-pcihp.dsl
src/ssdt-proc.dsl
tools/acpi_extract.py
tools/acpi_extract_preprocess.py
Each one of the listed people agreed to the following:
> If you allow the use of your contribution in QEMU under the
> terms of GPLv2 or later as proposed by this patch,
> please respond to this mail including the line:
>
> Acked-by: Name <email address>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jason Baron <jbaron@akamai.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Dave Frodin <dave.frodin@se-eng.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Magnus Christensson <magnus.christensson@intel.com>
Acked-by: Hu Tao <hutao@cn.fujitsu.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add API to find HPET using QOM.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add API to find pvpanic device and get its io port.
Will be used to fill in guest info structure.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds APIs that will be used to fill in
acpi tables, implemented using QOM,
to various ich9 components.
Some information is still missing in QOM,
so we fall back on lookups by type instead.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds APIs that will be used to fill in guest acpi tables.
Some required information is still lacking in QOM, so we
fall back on lookups by type and returning explicit types.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This defines a structure that will be used to fill in acpi tables
where relevant properties are not yet available using QOM.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Avoid a bit of code duplication, make
max file path constant reusable.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Address is already exposed, expose size for symmetry.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Useful to make it accessible through QOM.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Callers pass in the address so it's helpful for
them to be able to decode it.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make it possible to test unmapped status through QMP.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support ROM blobs not mapped into guest memory:
same as ROM files really but use caller's buffer.
Support invoking callback on access and
return memory pointer making it easier
for caller to update memory if necessary.
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make it easy to add read-only helpers for simple
integer properties in memory.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
now that a typedef for struct Error is available,
use it in qom/object.h to match coding style rules.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qapi/error.h is simple enough to be included in qom/object.h
direcly and prepares qom/object.h to use Error typedef.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of exposing the the irq field,
pci wrappers to qemu_set_irq or qemu_irq_*
can be used.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The fields hpev_intx and aer_intx were removed because
both AER and hot-plug events must use device's interrupt.
Assert/deassert interrupts using pci irq wrappers instead.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Interrupt pin is selected and saved into PCI_INTERRUPT_PIN
register during device initialization. Devices should not call
directly qemu_set_irq and specify the INTx pin on each call.
Added pci_* wrappers to replace qemu_set_irq, qemu_irq_raise,
qemu_irq_lower and qemu_irq_pulse, setting the irq
based on PCI_INTERRUPT_PIN.
Added pci_allocate_irq wrapper to be used by devices that
still need PCIDevice infrastructure to assert irqs.
Renamed a static method which was named already pci_set_irq.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qemu_allocate_irq returns a single qemu_irq.
The interface allows to specify an interrupt number.
qemu_free_irq frees it.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A MemoryRegion with negative priority was created and
it spans over all the pci address space.
It "intercepts" the accesses to unassigned pci
address space and will follow the pci spec:
1. returns -1 on read
2. does nothing on write
Note: setting the RECEIVED MASTER ABORT bit in the STATUS register
of the device that initiated the transaction will be
implemented in another series
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When memory regions overlap, priority can be used to specify
which of them takes priority. By making the priority values signed
rather than unsigned, we make it more convenient to implement
a situation where one "background" region should appear only
where no other region exists: rather than having to explicitly
specify a high priority for all the other regions, we can let them take
the default (zero) priority and specify a negative priority for the
background region.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# By Mark Wu (2) and Tomoki Sekiyama (1)
# Via Michael Roth
* mdroth/qga-pull-2013-10-10:
qemu-ga: Extend 'guest-info' command to expose flag 'success-response'
qemu-ga: Add interface to traverse the qmp command list by QmpCommand
qemu-ga: execute fsfreeze-freeze in reverse order of mounts
Message-id: 1381435782-25524-1-git-send-email-mdroth@linux.vnet.ibm.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
# By Richard Henderson
# Via Richard Henderson
* rth/tcg-pull:
exec: Add both big- and little-endian memory helpers
tcg: Add qemu_ld_st_i32/64
tcg: Add TCGMemOp
configure: Remove CONFIG_QEMU_LDST_OPTIMIZATION
tcg: Add tcg-be-ldst.h
tcg: Add tcg-be-null.h
exec: Delete is_tcg_gen_code and GETRA_EXT
tcg-aarch64: Update to helper_ret_*_mmu routines
tcg: Merge tcg_register_helper into tcg_context_init
tcg: Add tcg-runtime.c helpers to all_helpers
tcg: Put target helper data into an array.
tcg: Remove stray semi-colons from target-*/helper.h
tcg: Move helper registration into tcg_context_init
target-m68k: Rename helpers.h to helper.h
tcg: Use a GHashTable for tcg_find_helper
tcg: Delete tcg_helper_get_name declaration
tcg-hppa: Remove tcg backend
Message-id: 1381440525-6666-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
This reverts most of commit 3d1237fb2a.
The commit claims to sort the output of "-device help" "by
functionality rather than alphabetical". Issues:
* The output was unsorted before, not alphabetically sorted.
Misleading, but harmless enough.
* The commit doesn't just sort the output of "-device help" as it
claims, it adds categories to each line of "-device help", and it
prints devices once per category. In particular, devices without a
category aren't shown anymore. Maybe such devices should not exist,
but they do. Regression.
* Categories are also added to the output of "info qdm". Silent
change, not nice. Output remains unsorted, unlike "-device help".
I'm going to reimplement the feature we actually want, without the
warts. Reverting the flawed commit first should make it easier to
review. However, I can't revert it completely, since DeviceClass
member categories has been put to use. So leave that part in.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1381410021-1538-2-git-send-email-armbru@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
blockdev-add shouldn't automatically generate IDs, but will keep most of
the DriveInfo creation code.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
BlockDriverStates shouldn't be affected by an unplugged guest device,
except if created with the legacy -drive command line option or the
drive_add HMP command.
Make the automatic deletion as well as cancelling of jobs conditional on
an enable_auto_del boolean that is only set in drive_init().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Wenchao Xia <xiawenc@linux.vnet.ibm.com>
This field is used by blkverify to disable external snapshots creation.
It will also be used by block filters like quorum to disable external
snapshot creation.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
if a raw device like an iscsi target or host device is used
the current implementation makes a second call out to get
the block status of bs->file.
Signed-off-by: Peter Lieven <pl@kamp.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a function for generically dumping the ImageInfoSpecific information
in a human-readable format to block/qapi.c.
Use this function in bdrv_image_info_dump and qemu-io-cmds.c:info_f to
allow qemu-img info resp. qemu-io -c info to print that format specific
information.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a function for retrieving an ImageInfoSpecific object from a block
driver.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Switch the string to enum type BlockJobType in BlockJobDriver.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We will use BlockJobType as the enum type name of block jobs in QAPI,
rename current BlockJobType to BlockJobDriver, which will eventually
become a set of operations, similar to block drivers.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Step three in the transition: helpers not tied to the target
"default" endianness. To be used when the guest uses a memory
operation with non-default endianness.
Signed-off-by: Richard Henderson <rth@twiddle.net>
* Fix for X86CPU model field of qemu32/qemu64 CPU models
* Bug fix for longjmp on FreeBSD
* Removal of unused function
* Confinement of clone syscall infrastructure to linux-user
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=hQfy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'afaerber/tags/qom-cpu-for-anthony' into staging
QOM CPUState refactorings / X86CPU
* Fix for X86CPU model field of qemu32/qemu64 CPU models
* Bug fix for longjmp on FreeBSD
* Removal of unused function
* Confinement of clone syscall infrastructure to linux-user
# gpg: Signature made Wed 09 Oct 2013 03:40:51 AM PDT using RSA key ID 3E7E013F
# gpg: Can't check signature: public key not found
# By Andreas Färber (2) and others
# Via Andreas Färber
* afaerber/tags/qom-cpu-for-anthony:
cpu: Drop cpu_model_str from CPU_COMMON
cpu: Move cpu_copy() into linux-user
cputlb: Remove dead function tlb_update_dirty()
cpu-exec: Also reload CPUClass *cc after longjmp return in cpu_exec()
target-i386: Set model=6 on qemu64 & qemu32 CPU models
# By Amit Shah
# Via Amit Shah
* amit/char-remove-watch-on-unplug:
char: remove watch callback on chardev detach from frontend
char: use common function to disable callbacks on chardev close
char: move backends' io watch tag to CharDriverState
Message-id: 20131004154802.GA25646@grmbl.mre
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
Now we have several qemu-ga commands not returning response on success.
It has been documented in qga/qapi-schema.json already. This patch exposes
the 'success-response' flag by extending 'guest-info' command. With this
change, the clients can handle the command response more flexibly.
Signed-off-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
*fixed up commit subject
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
In the original code, qmp_get_command_list is used to construct
a list of all commands' name. To get the information of all qga
commands, it traverses the name list and search the command info
with its name. So it can cause O(n^2) in the number of commands.
This patch adds an interface to traverse the qmp command list by
QmpCommand to replace qmp_get_command_list. It can decrease the
complexity from O(n^2) to O(n).
Signed-off-by: Mark Wu <wudxw@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
*fix up commit subject
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
A minimal update to use the new helpers with the return address argument.
Tested-by: Claudio Fontana <claudio.fontana@linaro.org>
Reviewed-by: Claudio Fontana <claudio.fontana@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
One call inside of a loop to tcg_register_helper instead of hundreds
of sequential calls.
Presumably more icache and branch prediction friendly; resulting binary
size mostly unchanged on x86_64, as we're trading 32-bit rip-relative
references in .text for full 64-bit pointers in .rodata.
Signed-off-by: Richard Henderson <rth@twiddle.net>
# By Asias He (1) and Peter Lieven (1)
# Via Paolo Bonzini
* bonzini/scsi-next:
scsi: Allocate SCSITargetReq r->buf dynamically [CVE-2013-4344]
block/iscsi: reenable iscsi_co_get_block_status
Message-id: 1381332391-8781-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Anthony Liguori <aliguori@amazon.com>
r->buf is hardcoded to 2056 which is (256 + 1) * 8, allowing 256 luns at
most. If more than 256 luns are specified by user, we have buffer
overflow in scsi_target_emulate_report_luns.
To fix, we allocate the buffer dynamically.
Signed-off-by: Asias He <asias@redhat.com>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
# By Richard Henderson
# Via Richard Henderson
* rth/tcg-arm-pull:
tcg-arm: Move the tlb addend load earlier
tcg-arm: Remove restriction on qemu_ld output register
tcg-arm: Return register containing tlb addend
tcg-arm: Move load of tlb addend into tcg_out_tlb_read
tcg-arm: Use QEMU_BUILD_BUG_ON to verify constraints on tlb
tcg-arm: Use strd for tcg_out_arg_reg64
tcg-arm: Rearrange slow-path qemu_ld/st
tcg-arm: Use ldrd/strd for appropriate qemu_ld/st64
Message-id: 1380663109-14434-1-git-send-email-rth@twiddle.net
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
# By Sebastian Ottlik
# Via Stefan Weil
* sweil/mingw:
util: call socket_set_fast_reuse instead of setting SO_REUSEADDR
slirp: call socket_set_fast_reuse instead of setting SO_REUSEADDR
net: call socket_set_fast_reuse instead of setting SO_REUSEADDR
gdbstub: call socket_set_fast_reuse instead of setting SO_REUSEADDR
util: add socket_set_fast_reuse function which will replace setting SO_REUSEADDR
Message-id: 1380735690-24009-1-git-send-email-sw@weilnetz.de
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
# By Stefan Weil
# Via Stefan Weil
* sweil/tci:
misc: Use new rotate functions
bitops: Add rotate functions (rol8, ror8, ...)
tci: Add implementation of rotl_i64, rotr_i64
Message-id: 1380137693-3729-1-git-send-email-sw@weilnetz.de
Signed-off-by: Anthony Liguori <anthony@codemonkey.ws>
Since this is only read in cpu_copy() and linux-user has a global
cpu_model, drop the field from generic code.
Signed-off-by: Andreas Färber <afaerber@suse.de>
If a socket is closed it remains in TIME_WAIT state for some time. On operating
systems using BSD sockets the endpoint of the socket may not be reused while in
this state unless SO_REUSEADDR was set on the socket. On windows on the other
hand the default behaviour is to allow reuse (i.e. identical to SO_REUSEADDR on
other operating systems) and setting SO_REUSEADDR on a socket allows it to be
bound to a endpoint even if the endpoint is already used by another socket
independently of the other sockets state. This can even result in undefined
behaviour.
Many sockets used by QEMU should not block the use of their endpoint after being
closed while they are still in TIME_WAIT state. Currently QEMU sets SO_REUSEADDR
for such sockets, which can lead to problems on Windows. This patch introduces
the function socket_set_fast_reuse that should be used instead of setting
SO_REUSEADDR when fast socket reuse is desired and behaves correctly on all
operating systems.
As a failure of this function can only be caused by bad QEMU internal errors, an
assertion handles these situations. The return value is still passed on, to
minimize changes in client code and prevent unused variable warnings if NDEBUG
is defined.
Signed-off-by: Sebastian Ottlik <ottlik@fzi.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
There's no Intel CPU with family=6,model=2, and Linux and Windows guests
disable SEP when seeing that combination due to Pentium Pro erratum #82.
In addition to just having SEP ignored by guests, Skype (and maybe other
applications) runs sysenter directly without passing through ntdll on
Windows, and crashes because Windows ignored the SEP CPUID bit.
So, having model > 2 is a better default on qemu64 and qemu32 for two
reasons: making SEP really available for guests, and avoiding crashing
applications that work on bare metal.
model=3 would fix the problem, but it causes CPU enumeration problems
for Windows guests[1]. So let's set model=6, that matches "Athlon
(PM core)" on AMD and "P2 with on-die L2 cache" on Intel and it allows
Windows to use all CPUs as well as fixing sysenter.
[1] https://bugzilla.redhat.com/show_bug.cgi?id=508623
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Use the new helper_ret_*_mmu routines. Use a conditional call
to arrange for a tail-call from the store path, and to load the
return address for the helper for the load path.
Signed-off-by: Richard Henderson <rth@twiddle.net>
This includes pc and pci cleanups and enhancements,
and a virtio-net bugfix related to softmac programming.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSR83kAAoJECgfDbjSjVRpX08H/jKgYBNJaChev1TROIVHEGbu
IzvkjfocvKO+6wmhOf5x+xwFmzrijUMa1CPvOkCp8c2A3Iek7rmnedknlhXYh7dM
z5mXcvFGjnu7ST38ydF/Emk9+Z6rRg5Y/hkmlDyr+9lNcoiCDLXXcUrKjeIHNoWl
e8w3yiPCJ528QyrLwQ890XetJphv67pMlsjMgLQ2betMk++Ac/ctUf1D2p1X4NeQ
Q2drbo5Z4yDk0i6QMA3iLq1Bh/AhE10bCDq9rCzfZGIKVyncL6ne2pSi/xDvpLrF
dmxoiJ5QrK6xLnagCcn5T6SB9DkwbEPdL7qCqlxZ8USr7cVyPdzYtHtGSBWdeXY=
=xF01
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'mst/tags/for_anthony' into staging
pc,pci,virtio fixes and cleanups
This includes pc and pci cleanups and enhancements,
and a virtio-net bugfix related to softmac programming.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Sun 29 Sep 2013 01:51:16 AM CDT using RSA key ID D28D5469
# gpg: Can't check signature: public key not found
# By Michael S. Tsirkin (8) and others
# Via Michael S. Tsirkin
* mst/tags/for_anthony:
smbios: Factor out smbios_maybe_add_str()
smbios: Make multiple -smbios type= accumulate sanely
smbios: Improve diagnostics for conflicting entries
smbios: Convert to QemuOpts
smbios: Normalize smbios_entry_add()'s error handling to exit(1)
virtio-net: fix up HMP NIC info string on reset
pci: remove explicit check to 64K ioport size
piix4: disable io on reset
piix: use 64 bit window programmed by guest
q35: use 64 bit window programmed by guest
pci: add helper to retrieve the 64-bit range
range: add min/max operations on ranges
range: add Range to typedefs
q35: make pci window address/size match guest cfg
Message-id: 1380437951-21788-1-git-send-email-mst@redhat.com
# By Max Reitz (10) and others
# Via Kevin Wolf
* kwolf/for-anthony: (30 commits)
qcow2: Remove useless count_contiguous_clusters() parameter
qcow2: COMPRESSED on count_contiguous_clusters
qcow2: count_contiguous_clusters and compression
qcow2: Free only newly allocated clusters on error
qcow2: Always use error path in l2_allocate
qcow2: Don't put invalid L2 table into cache
qemu-iotests: Preallocated zero clusters in 061
qcow2: Correct bitmap size in zero expansion
qemu-iotests: Quote $TEST_IMG* and $TEST_DIR usage
qemu-iotests: Add basic ability to use binary sample images
qemu-iotests: fix qmp.py search path
block: use DIV_ROUND_UP in bdrv_co_do_readv
qcow2: Assert against currently impossible overflow
block: qed - use QEMU_PACKED for on-disk structures
block: qcow2 - used QEMU_PACKED for on-disk structures
block: vpc - use QEMU_PACKED for on-disk structures
block: vdi - use QEMU_PACKED for on-disk structures
rbd: avoid qemu_rbd_snap_list() memory leaks
qdict: Extract qdict_extract_subqdict
block: Fix compiler warning (-Werror=uninitialized)
...
Message-id: 1380296370-14523-1-git-send-email-kwolf@redhat.com
# By Richard Henderson (19) and Paolo Bonzini (2)
# Via Richard Henderson
* rth/tcg-ppc-pull: (21 commits)
tcg-ppc64: Implement CONFIG_QEMU_LDST_OPTIMIZATION
tcg-ppc64: Add _noaddr functions for emitting forward branches
tcg-ppc64: Streamline tcg_out_tlb_read
tcg-ppc64: Implement tcg_register_jit
tcg-ppc64: Handle long offsets better
tcg-ppc64: Tidy register allocation order
tcg-ppc64: Look through a constant function descriptor
tcg-ppc64: Fold constant call address into descriptor load
tcg-ppc64: Don't load the static chain from TCG
tcg-ppc64: Avoid code for nop move
tcg-ppc64: Use tcg_out64
tcg-ppc64: Use TCG_REG_Rn constants
tcg-ppc64: More use of TAI and SAI helper macros
tcg-ppc64: Reformat tcg-target.c
tcg-ppc: Fix and cleanup tcg_out_tlb_check
tcg-ppc: Use conditional branch and link to slow path
tcg-ppc: Cleanup tcg_out_qemu_ld/st_slow_path
tcg-ppc: Avoid code for nop move
tcg-ppc: use new return-argument ld/st helpers
tcg-ppc: fix qemu_ld/qemu_st for AIX ABI
...
Message-id: 1380126458-3247-1-git-send-email-rth@twiddle.net
# By Isaku Yamahata (4) and others
# Via Juan Quintela
* quintela/migration.next:
migration: ram_handle_compressed
arch_init: make is_zero_page accept size
migration: Fix debug print type
migration: add version supporting macros for struct pointer
rdma: constify ram_chunk_{index, start, end}
rdma: clean up of qemu_rdma_cleanup()
arch_init: right return for ram_save_iterate
savevm: fix wrong initialization by ram_control_load_hook
savevm: add comments for qemu_file_get_error()
Message-id: 1380024203-25897-1-git-send-email-quintela@redhat.com
contains the fixes from the previous pull request, which did not make
it yet.
Overall it contains
- a fix for kexec without kdump (which uses diag308 subcode 0 instead of 1)
- several sclp related fixes
- some initial sclp migration code
- the sclp line mode console
- A fix for a boot problem with the virtio ccw ipl bios
- zeroed out padding bytes for the notes section of dump-guest-memory
- some cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4rT1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'borntraeger/tags/s390-next-20130924' into staging
This is a bunch of fixes/changes for the s390 architecture. It also
contains the fixes from the previous pull request, which did not make
it yet.
Overall it contains
- a fix for kexec without kdump (which uses diag308 subcode 0 instead of 1)
- several sclp related fixes
- some initial sclp migration code
- the sclp line mode console
- A fix for a boot problem with the virtio ccw ipl bios
- zeroed out padding bytes for the notes section of dump-guest-memory
- some cleanups
# gpg: Signature made Tue 24 Sep 2013 02:18:44 AM CDT using RSA key ID B5A61C7C
# gpg: Can't check signature: public key not found
# By Christian Borntraeger (6) and others
# Via Christian Borntraeger
* borntraeger/tags/s390-next-20130924:
s390/sclplmconsole: Add support for SCLP line-mode console
s390/ebcdic: Move conversion tables to header file
s390/eventfacility: allow childs to handle more than 1 event type
s390/eventfacility: remove unused event_type variable
s390/eventfacility: Fix receive/send masks
s390/eventfacility: fix multiple Read Event Data sources
s390/sclp: add reset() functions
s390/sclpquiesce: Add code to support live migration
s390/sclpconsole: Add code to support live migration for sclpconsole
s390/sclpconsole: modify definition of input buffer
s390/kexec: Implement diag308 subcode 0
s390/ioinst: Moved the CC setting to the IO instruction handlers
s390/cpu: Make setcc() function available to other files
s390/ipl: Update the s390-ccw.img rom
s390/ipl: Fix waiting for virtio processing
s390/dump: zero out padding bytes in notes sections
s390/kvm: Add check for priviledged SCLP handler
Message-id: 1380007671-18976-1-git-send-email-borntraeger@de.ibm.com
Currently, -smbios type=T,NAME=VAL,... adds one field (T,NAME) with
value VAL to fw_cfg for each unique NAME. If NAME occurs multiple
times, the last one's VAL is used (before the QemuOpts conversion, the
first one was used).
Multiple -smbios can add multiple fields with the same (T, NAME).
SeaBIOS reads all of them from fw_cfg, but uses only the first field
(T, NAME). The others are ignored.
"First one wins, subsequent ones get ignored silently" isn't nice. We
commonly let the last option win. Useful, because it lets you
-readconfig first, then selectively override with command line
options.
Clean up -smbios to work the common way. Accumulate the settings,
with later ones overwriting earlier ones. Put the result into fw_cfg
(no more useless duplicates).
Bonus cleanup: qemu_uuid_parse() no longer sets SMBIOS system uuid by
side effect.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
So that it can be set in config file for -readconfig.
This tightens parsing of -smbios, and makes it more consistent with
other options: unknown parameters are rejected, numbers with trailing
junk are rejected, when a parameter is given multiple times, last
rather than first wins, ...
MST: drop one chunk to fix build errors
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It exits on all error conditions but one, where it returns -1.
Normalize, and return void.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently Xen hvm s3 has a bug coming from the difference between
qemu-traditioanl and qemu-xen. For qemu-traditional, the way to
resume from hvm s3 is via 'xl trigger' command. However, for
qemu-xen, the way to resume from hvm s3 inherited from standard
qemu, i.e. via QMP, and it doesn't work under Xen.
The root cause is, for qemu-xen, 'xl trigger' command didn't reset
devices, while QMP didn't unpause hvm domain though they did qemu
system reset.
We have two qemu patches and one xl patch to fix Xen hvm s3 bug.
This patch is the qemu patch 1. It adjusts qemu wakeup so that
Xen s3 resume logic (which will be implemented at qemu patch 2)
will be notified after qemu system reset.
Signed-off-by: Liu Jinsong <jinsong.liu@intel.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
These use a 32-bit load-of-immediate to save a mflr+addi+mtlr sequence.
Tested with a Windows 98 guest (pretty much the most recent thing I
could run on my PPC machine) and kvm-unit-tests's sieve.flat. The
speed up for sieve.flat is as high as 10% for qemu-system-i386, 25%
(no kidding) for qemu-system-x86_64 on my PowerBook G4.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Some drivers will have driver specifics options but no filename.
This new bool allow the block layer to treat them correctly.
The .bdrv_needs_filename is set in drivers not having .bdrv_parse_filename and
not having .bdrv_open.
The first exception to this rule will be the quorum driver.
Signed-off-by: Benoit Canet <benoit@irqsave.net>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds version supporting macros VMSTATE_STRUCT_POINTER_TEST_V
and VMSTATE_STRUCT_POINTER_V in addition to the already existing
VMSTATE_STRUCT_POINTER and VMSTATE_STRUCT_POINTER_TEST macros.
Cc: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Juan Quintela <quintela@redhat.com>
# By Stefan Hajnoczi (4) and others
# Via Stefan Hajnoczi
* stefanha/block:
virtio-blk: do not relay a previous driver's WCE configuration to the current
blockdev: do not default cache.no-flush to true
block: don't lose data from last incomplete sector
qcow2: Correct snapshots size for overlap check
coroutine: fix /perf/nesting coroutine benchmark
coroutine: add qemu_coroutine_yield benchmark
qemu-timer: do not take the lock in timer_pending
qemu-timer: make qemu_timer_mod_ns() and qemu_timer_del() thread-safe
qemu-timer: drop outdated signal safety comments
osdep: warn if open(O_DIRECT) on fails with EINVAL
libcacard: link against qemu-error.o for error_report()
Message-id: 1379698931-946-1-git-send-email-stefanha@redhat.com
# By Stefan Weil (8) and others
# Via Michael Tokarev
* mjt/trivial-patches:
tests/.gitignore: ignore test-throttle
exec: Fix broken build for MinGW (regression)
kvm: Fix compiler warning (clang)
tcg-sparc: Fix parenthesis warning
Makefile: Remove some more files when cleaning
target-i386: Fix segment cache dump
iov: avoid "orig_len may be used unitialized" warning
vscclient: remove unnecessary use of uninitialized variable
trace-events: Clean up with scripts/cleanup-trace-events.pl again
tci: Fix qemu-alpha on 32 bit hosts (wrong assertions)
*-user: Improve documentation for lock_user function
MAINTAINERS: Add missing entry to filelist for TCI target
translate-all: Fix formatting of dump output
*-user: Fix typo in comment (ulocking -> unlocking)
docs: Fix IO port number for CPU present bitmap.
q35: Fix typo in constant DEFUALT -> DEFAULT.
configure: Undefine _FORTIFY_SOURCE prior using it
Message-id: 1379696296-32105-1-git-send-email-mjt@msgid.tls.msk.ru
# By Alexey Kardashevskiy (3) and others
# Via Paolo Bonzini
* qemu-kvm/uq/master:
target-i386: add feature kvm_pv_unhalt
linux-headers: update to 3.12-rc1
target-i386: forward CPUID cache leaves when -cpu host is used
linux-headers: update to 3.11
kvm: fix traces to use %x instead of %d
kvmvapic: Clear also physical ROM address when entering INACTIVE state
kvmvapic: Enter inactive state on hardware reset
kvmvapic: Catch invalid ROM size
kvm irqfd: support direct msimessage to irq translation
fix steal time MSR vmsd callback to proper opaque type
kvm: warn if num cpus is greater than num recommended
cpu: Move cpu state syncs up into cpu_dump_state()
exec: always use MADV_DONTFORK
Message-id: 1379694292-1601-1-git-send-email-pbonzini@redhat.com
# By Hervé Poussineau (5) and Stefan Weil (1)
# Via Paolo Bonzini
* bonzini/scsi-next:
block/iscsi: Drop iscsi_co_get_block_status for older versions of libiscsi
lsi: add 53C810 variant
lsi: remove todo
lsi: ignore write accesses to CTEST0 registers
lsi: check ssid versus sdid only if ssid is valid
lsi: use constant name instead of its value
The following sequence happens:
- the SeaBIOS virtio-blk driver does not support the WCE feature, which
causes QEMU to disable writeback caching
- the Linux virtio-blk driver resets the device, finds WCE is available
but writeback caching is disabled; tells block layer to not send cache
flush commands
- the Linux virtio-blk driver sets the DRIVER_OK bit, which causes
writeback caching to be re-enabled, but the Linux virtio-blk driver does
not know of this side effect and cache flushes remain disabled
The bug is at the third step. If the guest does know about CONFIG_WCE,
QEMU should ignore the WCE feature's state. The guest will control the
cache mode solely using configuration space. This change makes Linux
do flushes correctly, but Linux will keep SeaBIOS's writethrough mode.
Hence, whenever the guest is reset, the cache mode of the disk should
be reset to whatever was specified in the "-drive" option. With this
change, the Linux virtio-blk driver finds that writeback caching is
enabled, and tells the block layer to send cache flush commands
appropriately.
Reported-by: Rusty Russell <rusty@au1.ibm.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add simple support for SCLP line-mode also known as operating
system messages. This can be added in addition to or instead of
the SCLP full screen console with -device sclplmconsole.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Move conversion tables to header file.
- In SCLP line mode processing EBCDIC/ASCII conversion is needed.
- An additional EBCDIC to ASCII conversion function is added.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Currently all handlers (quiesce, console) only handle one event type.
Some drivers will handle multiple (compatible) event types. Rework the
code accordingly.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
The event_type variable is never used. Get rid of it.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Currently we announce interchanged receive/send masks. This did not
trigger a bug, since the sclp console has the same masks for
send/receive and the Linux guest does not check the sclp mask for simple
events like quiesce. With other event users like the sclp line mode
console, we will have different send/receive bits. Fix it.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
