While not all callers of blk_remove_bs() are correct in this respect,
the assumption in the function is that callers hold the AioContext lock
of the BlockBackend (this is required by the drain calls in it).
In order to avoid deadlock in the nested event loop, bdrv_graph_wrlock()
has then to be called with the root BlockDriverState as its parameter
instead of NULL, so that this AioContext lock is temporarily dropped.
Fixes: https://issues.redhat.com/browse/RHEL-1761
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231115172012.112727-2-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Legacy software contains a standard mechanism for generating a reset to a
Serial ATA device - setting the SRST (software reset) bit in the Device
Control register.
Serial ATA has a more robust mechanism called COMRESET, also referred to
as port reset. A port reset is the preferred mechanism for error
recovery and should be used in place of software reset.
Commit e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
improved the handling of PxCI, such that PxCI gets cleared after handling
a non-NCQ, or NCQ command (instead of incorrectly clearing PxCI after
receiving anything - even a FIS that failed to parse, which should NOT
clear PxCI, so that you can see which command slot that caused an error).
However, simply clearing PxCI after a non-NCQ, or NCQ command, is not
enough, we also need to clear PxCI when receiving a SRST in the Device
Control register.
A legacy software reset is performed by the host sending two H2D FISes,
the first H2D FIS asserts SRST, and the second H2D FIS deasserts SRST.
The first H2D FIS will not get a D2H reply, and requires the FIS to have
the C bit set to one, such that the HBA itself will clear the bit in PxCI.
The second H2D FIS will get a D2H reply once the diagnostic is completed.
The clearing of the bit in PxCI for this command should ideally be done
in ahci_init_d2h() (if it was a legacy software reset that caused the
reset (a COMRESET does not use a command slot)). However, since the reset
value for PxCI is 0, modify ahci_reset_port() to actually clear PxCI to 0,
that way we can avoid complex logic in ahci_init_d2h().
This fixes an issue for FreeBSD where the device would fail to reset.
The problem was not noticed in Linux, because Linux uses a COMRESET
instead of a legacy software reset by default.
Fixes: e2a5d9b3d9 ("hw/ide/ahci: simplify and document PxCI handling")
Reported-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Message-ID: <20231108222657.117984-1-nks@flawful.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Coverity couldn't see that nr_existing was always going to be zero when
qemu_xen_xs_directory() returned NULL in the ENOENT case (CID 1523906).
Perhaps more to the point, neither could Peter at first glance. Improve
the code to hopefully make it clearer to Coverity and human reviewers
alike.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
If a Xen console is configured on the command line, do not add a default
serial port.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
* enable FEAT_RNG on Neoverse-N2
* hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
* Fix SME FMOPA (16-bit), BFMOPA
* hw/core/machine: Constify MachineClass::valid_cpu_types[]
* stm32f* machines: Report error when user asks for wrong CPU type
* hw/arm/fsl-imx: Do not ignore Error argument
-----BEGIN PGP SIGNATURE-----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=thIa
-----END PGP SIGNATURE-----
Merge tag 'pull-target-arm-20231121' of https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* enable FEAT_RNG on Neoverse-N2
* hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
* Fix SME FMOPA (16-bit), BFMOPA
* hw/core/machine: Constify MachineClass::valid_cpu_types[]
* stm32f* machines: Report error when user asks for wrong CPU type
* hw/arm/fsl-imx: Do not ignore Error argument
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmVchLYZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3kHMD/47tKxzrsXc6+V9esRQGi2H
# 1hAgLBwglEdxLXokF+Di41sh/fvK7wYVXO/hiWlq+9h3kG3D/u1N5r1TdMPMUb9j
# 4Sg3rOejn7nzkxVZ6MZ/K/1j84C9bfrt4sboVHZVRvWuvbiyuTuivEr4IqLYO4x3
# AIwhFMQ5gbNrmClZh/DBxj0keO13cp63Fg2JSSICdi+1Dw9rRXTyhJloMu1omeqc
# k/BXzjSeNXpLSMyGWBR3uaPcJBaGC1xnz3Z1V7fUY1EYD2Cu1oo5lEZ9aNO5t30d
# XW/qVGLa3b1Cb7WuEO247RnU3N2oZotozjFtdj/8IQoYWspM9RHyipEimUlegVdO
# 3fpu8QGsN1ljNiwjdk0i6OwS7SGxcPtteFOaqEf/Yogj4EOKTn/Rx5TT4vJ5DhmI
# 2w/9J15JWDIE1paNwecuFWbxCOOzSsOtSxzuyLSZDU3GlNfJ4zoF6YboROLYfejy
# NXZABFhGd/0ykX7r0VY1GGYXUQ+akv6q+VDmVZCP9gMiRUiqmFPwMLMLlcuHb8G5
# 8UztN5SvOG2EYXj28Zx0BnGCNiGdI15rWMb0veqAtbnn3yEdltW3O475BAhZ0PB7
# OVpLWnXwmWURm/BGlwb1PH5s3kgWgzOebcBgcnCftwFQ8EedQAQDA5FmT+nK5SfV
# VoOf89PngTubU6B3BOfeBw==
# =thIa
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 21 Nov 2023 05:21:42 EST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20231121' of https://git.linaro.org/people/pmaydell/qemu-arm:
hw/arm/fsl-imx: Do not ignore Error argument
hw/arm/stm32f100: Report error when incorrect CPU is used
hw/arm/stm32f205: Report error when incorrect CPU is used
hw/arm/stm32f405: Report error when incorrect CPU is used
hw/core/machine: Constify MachineClass::valid_cpu_types[]
target/arm: Fix SME FMOPA (16-bit), BFMOPA
hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
target/arm: enable FEAT_RNG on Neoverse-N2
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
-----BEGIN PGP SIGNATURE-----
iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZVwXJgAKCRBAov/yOSY+
30HKBAC4+3oAaMqRDEBTlYT0oHmU3IVRv7Pkuht72YZ57qQwjq21jMpxRdeuAAT2
McGzDIH/IbF0qG1HBako00jiwgGpx90aBU0KwOVgBjyjvUK2VXE268UoRs+WYVG/
7ljOHEnpvwJVTquAtDNFZIw0EFwiF75MP2rKvrSG8KmmrSu4hg==
=oHNA
-----END PGP SIGNATURE-----
Merge tag 'pull-loongarch-20231121' of https://gitlab.com/gaosong/qemu into staging
fixes tcg_out_mov aborted.
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZVwXJgAKCRBAov/yOSY+
# 30HKBAC4+3oAaMqRDEBTlYT0oHmU3IVRv7Pkuht72YZ57qQwjq21jMpxRdeuAAT2
# McGzDIH/IbF0qG1HBako00jiwgGpx90aBU0KwOVgBjyjvUK2VXE268UoRs+WYVG/
# 7ljOHEnpvwJVTquAtDNFZIw0EFwiF75MP2rKvrSG8KmmrSu4hg==
# =oHNA
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 20 Nov 2023 21:34:14 EST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20231121' of https://gitlab.com/gaosong/qemu:
tcg/loongarch64: Fix tcg_out_mov() Aborted
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In the minimal pixman API stub that is used when the real pixman
dependency is missing a NULL dereference happens when
virtio-gpu-rutabaga allocates a pixman image with bits = NULL and
rowstride_bytes = zero. A buffer of rowstride_bytes * height is
allocated which is NULL. However, in that scenario pixman calculates a
new stride value based on given width, height and format size.
This commit adds a helper function that performs the same logic as
pixman.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20231121093840.2121195-1-manos.pitsidianakis@linaro.org>
We should also consider -display vnc= as setting up a remote display,
and not attempt to add another default one.
The display_remote++ in qemu_setup_display() isn't necessary at this
point, but is there for completeness and further usages of the variable.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1988
Fixes: commit 484629fc81 ("vl: simplify display_remote logic ")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
When display is "none", we may still have remote displays (I think it
would be simpler if VNC/Spice were regular display btw). Return the
default VC then, and set them up to fix a regression when using remote
display and it used the TTY instead.
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/1989
Fixes: commit 1bec1cc0d ("ui/console: allow to override the default VC")
Reported-by: German Maglione <gmaglione@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Those display have their own implementation of "vc" chardev, which
doesn't use pixman. They also don't implement the width/height/cols/rows
options, so qemu_display_get_vc() should return a compatible argument.
This patch was meant to be with the pixman series, when the "vc" field
was introduced. It fixes a regression where VC are created on the
tty (or null) instead of the display own "vc" implementation.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Commit 1bec1cc0d ("ui/console: allow to override the default VC") changed
the behaviour of the "-display none" option, so that it now creates a
QEMU monitor on the terminal. "-display none" should not be tangled up
with whether we create a monitor or a serial terminal; it should purely
and only disable the graphical window. Changing its behaviour like this
breaks command lines which, for example, use semihosting for their
output and don't want a graphical window, as they now get a monitor they
never asked for.
It also breaks the command line we document for Xen in
docs/system/i386/xen.html:
$ ./qemu-system-x86_64 --accel kvm,xen-version=0x40011,kernel-irqchip=split \
-display none -chardev stdio,mux=on,id=char0,signal=off -mon char0 \
-device xen-console,chardev=char0 -drive file=${GUEST_IMAGE},if=xen
qemu-system-x86_64: cannot use stdio by multiple character devices
qemu-system-x86_64: could not connect serial device to character backend
'stdio'
When qemu is compiled without PIXMAN, by default the serials aren't
muxed with the monitor anymore on stdio. The serials are redirected to
"null" instead, and the monitor isn't set up.
Fixes: commit 1bec1cc0d ("ui/console: allow to override the default VC")
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
In net_cleanup() we only need to delete the netdevs, as those may have
state which outlives Qemu when it exits, and thus may actually need to
be cleaned up on exit.
The nics, on the other hand, are owned by the device which created them.
Most devices don't bother to clean up on exit because they don't have
any state which will outlive Qemu... but XenBus devices do need to clean
up their nodes in XenStore, and do have an exit handler to delete them.
When the XenBus exit handler destroys the xen-net-device, it attempts
to delete its nic after net_cleanup() had already done so. And crashes.
Fix this by only deleting netdevs as we walk the list. As the comment
notes, we can't use QTAILQ_FOREACH_SAFE() as each deletion may remove
*multiple* entries, including the "safely" saved 'next' pointer. But
we can store the *previous* entry, since nics are safe.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
This implementation follows what bottom half does, but it does not add
a tracepoint for the case that the network device backend started
delivering a packet to a device which is already engaging in I/O. This
is because such reentrancy frequently happens for
qemu_flush_queued_packets() and is insignificant.
Fixes: CVE-2023-3019
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
In preparation for such a change, add MemReentrancyGuard * as a
parameter of qemu_new_nic().
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The PNV I2C Controller was clearing the status register
after a reset without repopulating the "upper threshold
for I2C ports", "Command Complete" and the SCL/SDA input
level fields.
Fixed this for resets caused by a system reset as well
as from writing to the "Immediate Reset" register.
Fixes: 263b81ee15 ("ppc/pnv: Add an I2C controller model")
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PNV I2C engines for power9 and power10 were being assigned a base
XSCOM address that was off by one I2C engine's address range such
that engine 0 had engine 1's address and so on. The xscom address
assignment was being based on the device tree engine numbering, which
starts at 1. Rather than changing the device tree numbering to start
with 0, the addressing was changed to be based on the existing device
tree numbers minus one.
Fixes: 1ceda19c28 ("ppc/pnv: Connect PNV I2C controller to powernv10)
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The patch below fixes a bug in the VSX_CVT_FP_TO_INT and VSX_CVT_FP_TO_INT2
macros in target/ppc/fpu_helper.c where a non-NaN floating point value from the
source vector is incorrectly converted to 0, 0x80000000, or 0x8000000000000000
instead of the expected value if a preceding source floating point value from
the same source vector was a NaN.
The bug in the VSX_CVT_FP_TO_INT and VSX_CVT_FP_TO_INT2 macros in
target/ppc/fpu_helper.c was introduced with commit c3f24257e3.
This patch also adds a new vsx_f2i_nan test in tests/tcg/ppc64 that checks that
the VSX xvcvspsxws, xvcvspuxws, xvcvspsxds, xvcvspuxds, xvcvdpsxws, xvcvdpuxws,
xvcvdpsxds, and xvcvdpuxds instructions correctly convert non-NaN floating point
values to integer values if the source vector contains NaN floating point values.
Fixes: c3f24257e3 ("target/ppc: Clear fpstatus flags on helpers missing it")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1941
Signed-off-by: John Platts <john_platts@hotmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Coverity warns that "i2c_bus_busy(i2c->busses[i]) << i" might overflow
because the expression is evaluated using 32-bit arithmetic and then
used in a context expecting a uint64_t.
While we are at it, introduce a PNV_I2C_MAX_BUSSES constant and check
the number of busses at realize time.
Fixes: Coverity CID 1523918
Cc: Glenn Miles <milesg@linux.vnet.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On LoongArch host, we got an Aborted from tcg_out_mov().
qemu-x86_64 configure with '--enable-debug'.
> (gdb) b /home1/gaosong/code/qemu/tcg/loongarch64/tcg-target.c.inc:312
> Breakpoint 1 at 0x2576f0: file /home1/gaosong/code/qemu/tcg/loongarch64/tcg-target.c.inc, line 312.
> (gdb) run hello
[...]
> Thread 1 "qemu-x86_64" hit Breakpoint 1, tcg_out_mov (s=0xaaaae91760 <tcg_init_ctx>, type=TCG_TYPE_V128, ret=TCG_REG_V2,
> arg=TCG_REG_V0) at /home1/gaosong/code/qemu/tcg/loongarch64/tcg-target.c.inc:312
> 312 g_assert_not_reached();
> (gdb) bt
> #0 tcg_out_mov (s=0xaaaae91760 <tcg_init_ctx>, type=TCG_TYPE_V128, ret=TCG_REG_V2, arg=TCG_REG_V0)
> at /home1/gaosong/code/qemu/tcg/loongarch64/tcg-target.c.inc:312
> #1 0x000000aaaad0fee0 in tcg_reg_alloc_mov (s=0xaaaae91760 <tcg_init_ctx>, op=0xaaaaf67c20) at ../tcg/tcg.c:4632
> #2 0x000000aaaad142f4 in tcg_gen_code (s=0xaaaae91760 <tcg_init_ctx>, tb=0xffe8030340 <code_gen_buffer+197328>,
> pc_start=4346094) at ../tcg/tcg.c:6135
[...]
> (gdb) c
> Continuing.
> **
> ERROR:/home1/gaosong/code/qemu/tcg/loongarch64/tcg-target.c.inc:312:tcg_out_mov: code should not be reached
> Bail out! ERROR:/home1/gaosong/code/qemu/tcg/loongarch64/tcg-target.c.inc:312:tcg_out_mov: code should not be reached
>
> Thread 1 "qemu-x86_64" received signal SIGABRT, Aborted.
> 0x000000fff7b1c390 in raise () from /lib64/libc.so.6
> (gdb) q
Fixes: 16288ded94 ("tcg/loongarch64: Lower basic tcg vec ops to LSX")
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20231120065916.374045-1-gaosong@loongson.cn>
Both i.MX25 and i.MX6 SoC models ignore the Error argument when
setting the PHY number. Pick &error_abort which is the error
used by the i.MX7 SoC (see commit 1f7197deb0 "ability to change
the FEC PHY on i.MX7 processor").
Fixes: 74c1330582 ("ability to change the FEC PHY on i.MX25 processor")
Fixes: a9c167a3c4 ("ability to change the FEC PHY on i.MX6 processor")
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231120115116.76858-1-philmd@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'stm32vldiscovery' machine ignores the CPU type requested by
the command line. This might confuse users, since the following
will create a machine with a Cortex-M3 CPU:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
qemu-system-aarch64: Invalid CPU type: neoverse-n1-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'netduino2' machine ignores the CPU type requested by the
command line. This might confuse users, since the following will
create a machine with a Cortex-M3 CPU:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
qemu-system-arm: Invalid CPU type: cortex-a9-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both 'netduinoplus2' and 'olimex-stm32-h405' machines ignore the
CPU type requested by the command line. This might confuse users,
since the following will create a machine with a Cortex-M4 CPU:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
qemu-system-aarch64: Invalid CPU type: cortex-r5f-arm-cpu
The valid types are: cortex-m4-arm-cpu
Since the SoC family can only use Cortex-M4 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Constify MachineClass::valid_cpu_types[i], as suggested by Richard
Henderson.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20231117071704.35040-2-philmd@linaro.org
[PMD: Constify HPPA machines,
restrict valid_cpu_types to machine_class_init() handlers]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ICC_PMR_ELx and ICV_PMR_ELx bit masks returned from
ic{c,v}_fullprio_mask should technically also remove any
bit above 7 as these are marked reserved (read 0) and should
therefore should not be written as anything other than 0.
This was noted during a run of a proprietary test system and
discused on the mailing list [1] and initially thought not to
be an issue due to RES0 being technically allowed to be
written to and read back as long as the implementation does
not use the RES0 bits. It is very possible that the values
are used in comparison without masking, as pointed out by
Peter in [2], if (cs->hppi.prio >= cs->icc_pmr_el1) may well
do the wrong thing.
Masking these values in ic{c,v}_fullprio_mask() should fix
this and prevent any future problems with playing with the
values.
[1]: https://lists.nongnu.org/archive/html/qemu-arm/2023-11/msg00607.html
[2]: https://lists.nongnu.org/archive/html/qemu-arm/2023-11/msg00737.html
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Message-id: 20231116172818.792364-1-ben.dooks@codethink.co.uk
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I noticed that Neoverse-V1 has FEAT_RNG enabled so let enable it also on
Neoverse-N2.
Signed-off-by: Marcin Juszkiewicz <marcin.juszkiewicz@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20231114103443.1652308-1-marcin.juszkiewicz@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Two patches for 8.2.
The SHRPD patch fixes a real translation bug which then allows to boot
the 64-bit Linux kernels of the Debian-11 and Debian-12 installation CDs.
The second patch adds the instruction byte sequence to the
assembly log. This is not an actual bug fix, but it's important since
it helps a lot when trying to fix qemu translation bugs on hppa.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZVfHPwAKCRD3ErUQojoP
X3TrAQD2SfFsTWIYqTamh1ZHmydaJRL1xhXmPMqXgXFkDmiyhQD/VeyIyWEGj5Oe
x70WR8HrtkadsUddgSGzFRChaVb0/wI=
=Sapq
-----END PGP SIGNATURE-----
Merge tag 'hppa64-fixes-pull-request' of https://github.com/hdeller/qemu-hppa into staging
HPPA64-PATCHES-for-8.2
Two patches for 8.2.
The SHRPD patch fixes a real translation bug which then allows to boot
the 64-bit Linux kernels of the Debian-11 and Debian-12 installation CDs.
The second patch adds the instruction byte sequence to the
assembly log. This is not an actual bug fix, but it's important since
it helps a lot when trying to fix qemu translation bugs on hppa.
# -----BEGIN PGP SIGNATURE-----
#
# iHUEABYKAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCZVfHPwAKCRD3ErUQojoP
# X3TrAQD2SfFsTWIYqTamh1ZHmydaJRL1xhXmPMqXgXFkDmiyhQD/VeyIyWEGj5Oe
# x70WR8HrtkadsUddgSGzFRChaVb0/wI=
# =Sapq
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 17 Nov 2023 15:04:15 EST
# gpg: using EDDSA key BCE9123E1AD29F07C049BBDEF712B510A23A0F5F
# gpg: Good signature from "Helge Deller <deller@gmx.de>" [unknown]
# gpg: aka "Helge Deller <deller@kernel.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 4544 8228 2CD9 10DB EF3D 25F8 3E5F 3D04 A7A2 4603
# Subkey fingerprint: BCE9 123E 1AD2 9F07 C049 BBDE F712 B510 A23A 0F5F
* tag 'hppa64-fixes-pull-request' of https://github.com/hdeller/qemu-hppa:
disas/hppa: Show hexcode of instruction along with disassembly
target/hppa: Fix 64-bit SHRPD instruction
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In FDPIC signal handlers are passed around as FD pointers. Actual code
address and GOT pointer must be fetched from memory by the QEMU code
that implements kernel signal delivery functionality. This change is
equivalent to the following kernel change:
9c2cc74fb31e ("xtensa: fix signal delivery to FDPIC process")
Cc: qemu-stable@nongnu.org
Fixes: d2796be69d ("linux-user: add support for xtensa FDPIC")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
On hppa many instructions can be expressed by different bytecodes.
To be able to debug qemu translation bugs it's therefore necessary to see the
currently executed byte codes without the need to lookup the sequence without
the full executable.
With this patch the instruction byte code is shown beside the disassembly.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
When shifting the two joined 64-bit registers right, shift the upper
64-bit register to the left and the lower 64-bit register to the right
before merging them with OR.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Improve
$ qemu-system-x86_64 -device max-x86_64-cpu,vendor=me
qemu-system-x86_64: -device max-x86_64-cpu,vendor=me: Property '.vendor' doesn't take value 'me'
to
qemu-system-x86_64: -device max-x86_64-cpu,vendor=0123456789abc: value of property 'vendor' must consist of exactly 12 characters
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[Typo corrected]
The error message
{"execute": "balloon", "arguments":{"value": -1}}
{"error": {"class": "GenericError", "desc": "Parameter 'target' expects a size"}}
points to 'target' instead of 'value'. Fix:
{"error": {"class": "GenericError", "desc": "Parameter 'value' expects a size"}}
Root cause: qmp_balloon()'s parameter is named @target. Rename it to
@value to match the QAPI schema.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-7-armbru@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
The error message
$ qemu-system-x86_64 -netdev user,id=net0,ipv6-net=fec0::0/
qemu-system-x86_64: -netdev user,id=net0,ipv6-net=fec0::0/: Parameter 'ipv6-prefixlen' expects a number
points to ipv6-prefixlen instead of ipv6-net. Fix:
qemu-system-x86_64: -netdev user,id=net0,ipv6-net=fec0::0/: parameter 'ipv6-net' expects a number after '/'
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-6-armbru@redhat.com>
set_password with "protocol": "vnc" supports only "connected": "keep".
Any other value is rejected with
Invalid parameter 'connected'
Improve this to
parameter 'connected' must be 'keep' when 'protocol' is 'vnc'
client_migrate_info requires "port" or "tls-port". When both are
missing, it fails with
Parameter 'port/tls-port' is missing
Improve this to
parameter 'port' or 'tls-port' is required
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-5-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
When the PID passed to guest-exec-status does not exist, we report
"Invalid parameter 'pid'"
Improve this to
"PID 1234 does not exist"
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-4-armbru@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Improve
(qemu) sync-profile of
Error: Invalid parameter 'of'
to
Error: invalid parameter 'of', expecting 'on', 'off', or 'reset'
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-3-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dave@treblig.org>
When dynamic-reconfiguration is off, hot plug / unplug can fail with
"Bus 'spapr-pci-host-bridge' does not support hotplugging".
spapr-pci-host-bridge is a device, not a bus. Report the name of the
bus it provides instead: 'pci.0'.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20231031111059.3407803-2-armbru@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Like replay_linux.py, reverse_debugging.py starts the vm with console
set but does not interact with it (e.g., with wait_for_console_pattern).
In this situation, the console should have a drainer attached so the
socket does not fill. replay_linux.py has a drainer, but it is missing
from reverse_debugging.py.
Per analysis in Link: this can cause the console socket/pipe to fill and
QEMU get stuck in qemu_chr_write_buffer, leading to strange test case
failures (ppc64 fails because it prints a lot to console in early bios).
Attaching a drainer prevents this.
Note, this commit does not fix bugs introduced by the commits referenced
in the first two Fixes: tags, but together those commits conspire to
irritate the problem and cause test case failure, which this commit
fixes.
Link: https://lore.kernel.org/qemu-devel/ZVT-bY9YOr69QTPX@redhat.com/
Fixes: 1d4796cd00 ("python/machine: use socketpair() for console connections")
Fixes: 761a13b239 ("tests/avocado: ppc64 reverse debugging tests for pseries and powernv")
Fixes: be52eca309 ("tests/acceptance: add reverse debugging test")
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-ID: <20231116115354.228678-1-npiggin@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
assertEquals() has been removed in Python 3.12 and should be replaced by
assertEqual(). See: https://docs.python.org/3.12/whatsnew/3.12.html#id3
Message-ID: <20231116061956.14676-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Ani Sinha <anisinha@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It's failing very often, so don't run this by default anymore
until it gets fixed.
Message-ID: <20231114153019.295131-1-thuth@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
In a perfect world we'd have reproducible tests,
but then we'd be sure we run the same binaries.
If a binary artifact isn't hashed, we have no idea
what we are running. Therefore enforce hashing for
all our artifacts.
With this change, unhashed artifacts produce:
$ avocado run tests/avocado/multiprocess.py
(1/2) tests/avocado/multiprocess.py:Multiprocess.test_multiprocess_x86_64:
ERROR: QemuBaseTest.fetch_asset() missing 1 required positional argument: 'asset_hash' (0.19 s)
Inspired-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-ID: <20231115205149.90765-1-philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
