We extend PLIC emulation to allow multiple instances of PLIC in
a QEMU RISC-V machine. To achieve this, we remove first HART id
zero assumption from PLIC emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200616032229.766089-3-anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Claiming an interrupt and changing the source priority both potentially
affect whether an interrupt is pending, thus we must re-compute xEIP.
Note that we don't put the sifive_plic_update inside sifive_plic_claim
so that the logging of a claim (and the resulting IRQ) happens before
the state update, making the causal effect clear, and that we drop the
explicit call to sifive_plic_print_state when claiming since
sifive_plic_update already does that automatically at the end for us.
This can result in both spurious interrupt storms if you fail to
complete an IRQ before enabling interrupts (and no other actions occur
that result in a call to sifive_plic_update), but also more importantly
lost interrupts if a disabled interrupt is pending and then becomes
enabled.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200618210649.22451-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The source priorities can be used to order sources with respect to other
sources, not just as a way to enable/disable them based off a threshold.
We must therefore always claim the highest-priority source, rather than
the first source we find.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200618202343.20455-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
The global smp variables in riscv are replaced with smp machine properties.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190518205428.90532-6-like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
[ehabkost: fix spike_board_init()]
[ehabkost: fix riscv_sifive_e_soc_init()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of using error_report() to print guest errors let's use
qemu_log_mask(LOG_GUEST_ERROR,...) to log the error.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch fixes four different things, to maintain bisectability they
have been merged into a single patch. The following fixes are below:
sifive_plic: Fix incorrect irq calculation
The irq is incorrectly calculated to be off by one. It has worked in the
past as the priority_base offset has also been set incorrectly. We are
about to fix the priority_base offset so first first the irq
calculation.
sifive_u: Fix PLIC priority base offset and numbering
According to the FU540 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00. The same manual also specifies that the
PLIC only has 53 source priorities. Fix these two incorrect header
files.
We also need to over extend the plic_gpios[] array as the PLIC sources
count from 1 and not 0.
riscv: sifive_e: Fix PLIC priority base offset
According to the FE31 manual the PLIC source priority address starts at
an offset of 0x04 and not 0x00.
riscv: virt: Fix PLIC priority base offset
Update the virt offsets based on the newly updated SiFive U and SiFive E
offsets.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
We can't allow the supervisor to control SEIP as this would allow the
supervisor to clear a pending external interrupt which will result in
lost a interrupt in the case a PLIC is attached. The SEIP bit must be
hardware controlled when a PLIC is attached.
This logic was previously hard-coded so SEIP was always masked even
if no PLIC was attached. This patch adds riscv_cpu_claim_interrupts
so that the PLIC can register control of SEIP. In the case of models
without a PLIC (spike), the SEIP bit remains software controlled.
This interface allows for hardware control of supervisor timer and
software interrupts by other interrupt controller models.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The mode variable only uses the lower 4-bits (M,H,S,U) so
replace the GCC specific __builtin_popcount with ctpop8.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Set msi_nonbroken as true for the PLIC.
According to the comment located here:
https://git.qemu.org/?p=qemu.git;a=blob;f=hw/pci/msi.c;h=47d2b0f33c664533b8dbd5cb17faa8e6a01afe1f;hb=HEAD#l38
the msi_nonbroken variable should be set to true even if they don't
support MSI. In this case that is what we are doing as we don't support
MSI.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reported-by: Andrea Bolognani <abologna@redhat.com>
Reported-by: David Abdurachmanov <david.abdurachmanov@gmail.com>
Message-Id: <256afbb2da005dc62c159b0f4a4fc0d95c050660.1552679970.git.alistair.francis@wdc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The address calculation for the pending bitfield had
a copy paste bug. This bug went unnoticed because the Linux
PLIC driver does not read the pending bitfield, rather it
reads pending interrupt numbers from the claim register
and writes acknowledgements back to the claim register.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Reported-by: Vincent Siles <vincent.siles@ens-lyon.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Change the API of riscv_set_local_interrupt to take a
write mask and value to allow setting and clearing of
multiple local interrupts atomically in a single call.
Rename the new function to riscv_cpu_update_mip.
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The PLIC previously used a mutex to protect against concurrent
access to the claimed and pending bitfields. Instead of using
a mutex, we update the bitfields using atomic_cmpxchg.
Rename sifive_plic_num_irqs_pending to sifive_plic_irqs_pending
and add an early out if any interrupts are pending as the
count of pending interrupts is not used.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of creating the interrupt in lines with qemu_allocate_irq() use
qdev_init_gpio_in() as this gives us the ability to use the qdev*gpio*()
helpers later on.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
The PLIC (Platform Level Interrupt Controller) device provides a
parameterizable interrupt controller based on SiFive's PLIC specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
