and get rid of an unnecessary drive_get(IF_MTD) call.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the -nodefaults option is set, flash devices should be created
with :
-blockdev node-name=fmc0,driver=file,filename=./flash.img \
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0 \
To be noted that in this case, the ROM will not be installed and the
initial boot sequence (U-Boot loading) will fetch instructions using
SPI transactions which is significantly slower. That's exactly how HW
operates though.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, a set of default flash devices is created at machine init
and drives defined on the QEMU command line are associated to the FMC
and SPI controllers in sequence :
-drive file<file>,format=raw,if=mtd
-drive file<file1>,format=raw,if=mtd
The CS lines are wired in the same creation loop. This makes a strong
assumption on the ordering and is not very flexible since only a
limited set of flash devices can be defined : 1 FMC + 1 or 2 SPI,
which is less than what the SoC really supports.
A better alternative would be to define the flash devices on the
command line using a blockdev attached to a CS line of a SSI bus :
-blockdev node-name=fmc0,driver=file,filename=./flash.img
-device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0
However, user created flash devices are not correctly wired to their
SPI controller and consequently can not be used by the machine. Fix
that and wire the CS lines of all available devices when the SSI bus
is reset.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
On 32-bit hosts, RAM has a 2047 MB limit. Use a macro to define the
default ram size of machines (AST2600 SoC) that can have 2 GB.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Most of the Aspeed machines use the UART5 device for the boot console,
and QEMU connects the first serial Chardev to this SoC device for this
purpose. See routine connect_serial_hds_to_uarts().
Nevertheless, some machines use another boot console, such as the fuji,
and commit 5d63d0c76c ("hw/arm/aspeed: Allow machine to set UART
default") introduced a SoC class attribute 'uart_default' and property
to be able to change the boot console device. It was later changed by
commit d2b3eaefb4 ("aspeed: Refactor UART init for multi-SoC machines").
The "bmc-console" machine option goes a step further and lets the user define
the UART device from the QEMU command line without introducing a new
machine definition. For instance, to use device UART3 (mapped on
/dev/ttyS2 under Linux) instead of the default UART5, one would use :
-M ast2500-evb,bmc-console=uart3
Cc: Abhishek Singh Dagur <abhishek@drut.io>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This should also avoid Coverity to report a memory leak warning when
the QEMU process exits. See CID 1508061.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The current modeling of Rainier machine creates zero filled VPDs(EEPROMs).
This makes some services and applications unhappy and causing them to fail.
Hence this drop adds some fabricated data for system and BMC FRU so that
vpd services are happy and active.
Tested:
- The system-vpd.service is active.
- VPD service related to bmc is active.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: commit title cleanup ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When writing the secondary-CPU stub boot loader code to the guest,
use arm_write_bootloader() instead of directly calling
rom_add_blob_fixed(). This fixes a bug on big-endian hosts, because
arm_write_bootloader() will correctly byte-swap the host-byte-order
array values into the guest-byte-order to write into the guest
memory.
Cc: qemu-stable@nongnu.org
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20230424152717.1333930-3-peter.maydell@linaro.org
[PMM: Moved the "make arm_write_bootloader() function public" part
to its own patch; updated commit message to note that this fixes
an actual bug; adjust to the API changes noted in previous commit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added TMP421 type sensor support in tiogapass platform.
Tested: Tested and verified in tiogapass platform.
Signed-off-by: Karthikeyan Pasupathi <pkarthikeyan1509@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230307103334.3586755-1-pkarthikeyan1509@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Added TMP421 type support in yosemite v2 platform.
Tested: Tested and verified in yosemite V2 platform.
Signed-off-by: Karthikeyan Pasupathi <pkarthikeyan1509@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20230307095239.3583613-1-pkarthikeyan1509@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It's cleaner and removes the curious '+ 1' required to skip the DMA
IRQ line of the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
To avoid the SPI transactions fetching instructions from the FMC CE0
flash device and speed up boot, a ROM can be created if a drive is
available.
Reverse the logic to allow a machine to boot without a drive, using a
block device instead :
-blockdev node-name=fmc0,driver=file,filename=/path/to/flash.img \
-device mx66u51235f,bus=ssi.0,drive=fmc0
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The default boot address of the Aspeed SoCs is 0x0. For this reason,
the FMC flash device contents are remapped by HW on the first 256MB of
the address space. In QEMU, this is currently done in the machine init
with the setup of a region alias.
Move this code to the SoC and introduce an extra container to prepare
ground for the boot ROM region which will overlap the FMC flash
remapping.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch support Tiogapass in QEMU environment.
and introduced EEPROM BMC FRU data support "add tiogapass_bmc_fruid data"
along with the machine support.
Signed-off-by: Karthikeyan Pasupathi <pkarthikeyan1509@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - commit log topic update
- checkpatch issues
- Documentation update ]
Message-Id: <20230216184342.253868-1-pkarthikeyan1509@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch support Yosemitev2 in QEMU environment.
and introduced EEPROM BMC FRU data support "add fbyv2_bmc_fruid data"
along with the machine support.
Signed-off-by: Karthikeyan Pasupathi <pkarthikeyan1509@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: - commit log topic update
- Documentation update ]
Message-Id: <20230216133326.216017-1-pkarthikeyan1509@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
- Create aspeed_eeprom.c and aspeed_eeprom.h
- Include aspeed_eeprom.c in CONFIG_ASPEED meson source files
- Include aspeed_eeprom.h in aspeed.c
- Add fby35_bmc_fruid data
- Use new at24c_eeprom_init_rom helper to initialize BMC FRUID EEPROM with data
from aspeed_eeprom.c
wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd
qemu-system-aarch64 -machine fby35-bmc -nographic -mtdblock fby35.mtd
...
user: root
pass: 0penBmc
...
root@bmc-oob:~# fruid-util bb
FRU Information : Baseboard
--------------- : ------------------
Chassis Type : Rack Mount Chassis
Chassis Part Number : N/A
Chassis Serial Number : N/A
Board Mfg Date : Fri Jan 7 10:30:00 2022
Board Mfg : XXXXXX
Board Product : Management Board wBMC
Board Serial : XXXXXXXXXXXXX
Board Part Number : XXXXXXXXXXXXXX
Board FRU ID : 1.0
Board Custom Data 1 : XXXXXXXXX
Board Custom Data 2 : XXXXXXXXXXXXXXXXXX
Product Manufacturer : XXXXXX
Product Name : Yosemite V3.5 EVT2
Product Part Number : XXXXXXXXXXXXXX
Product Version : EVT2
Product Serial : XXXXXXXXXXXXX
Product Asset Tag : XXXXXXX
Product FRU ID : 1.0
Product Custom Data 1 : XXXXXXXXX
Product Custom Data 2 : N/A
root@bmc-oob:~# fruid-util bmc
FRU Information : BMC
--------------- : ------------------
Board Mfg Date : Mon Jan 10 21:42:00 2022
Board Mfg : XXXXXX
Board Product : BMC Storage Module
Board Serial : XXXXXXXXXXXXX
Board Part Number : XXXXXXXXXXXXXX
Board FRU ID : 1.0
Board Custom Data 1 : XXXXXXXXX
Board Custom Data 2 : XXXXXXXXXXXXXXXXXX
Product Manufacturer : XXXXXX
Product Name : Yosemite V3.5 EVT2
Product Part Number : XXXXXXXXXXXXXX
Product Version : EVT2
Product Serial : XXXXXXXXXXXXX
Product Asset Tag : XXXXXXX
Product FRU ID : 1.0
Product Custom Data 1 : XXXXXXXXX
Product Custom Data 2 : Config A
root@bmc-oob:~# fruid-util nic
FRU Information : NIC
--------------- : ------------------
Board Mfg Date : Tue Nov 2 08:51:00 2021
Board Mfg : XXXXXXXX
Board Product : Mellanox ConnectX-6 DX OCP3.0
Board Serial : XXXXXXXXXXXXXXXXXXXXXXXX
Board Part Number : XXXXXXXXXXXXXXXXXXXXX
Board FRU ID : FRU Ver 0.02
Product Manufacturer : XXXXXXXX
Product Name : Mellanox ConnectX-6 DX OCP3.0
Product Part Number : XXXXXXXXXXXXXXXXXXXXX
Product Version : A9
Product Serial : XXXXXXXXXXXXXXXXXXXXXXXX
Product Custom Data 3 : ConnectX-6 DX
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20230128060543.95582-5-peter@pjd.dev
Signed-off-by: Cédric Le Goater <clg@kaod.org>
aspeed_eeprom_init is an exact copy of at24c_eeprom_init, not needed.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20230128060543.95582-3-peter@pjd.dev
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This helper is useful in board initialization because lets users initialize and
realize an EEPROM on an I2C bus with a single function call.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20230128060543.95582-2-peter@pjd.dev
Signed-off-by: Cédric Le Goater <clg@kaod.org>
supermicrox11-bmc is configured with ast2400-a1 SoC. This does not match
the Supermicro documentation for X11 BMCs, and it does not match the
devicetree file in the Linux kernel.
As it turns out, some Supermicro X11 motherboards use AST2400 SoCs,
while others use AST2500.
Introduce new machine type supermicrox11-spi-bmc with AST2500 SoC
to match the devicetree description in the Linux kernel. Hardware
configuration details for this machine type are guesswork and taken
from defaults as well as from the Linux kernel devicetree file.
The new machine type was tested with aspeed-bmc-supermicro-x11spi.dts
from the Linux kernel and with Linux versions 6.0.3 and 6.1-rc2.
Linux booted successfully from initrd and from both SPI interfaces.
Ethernet interfaces were confirmed to be operational.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Link: https://lore.kernel.org/r/20221025165109.1226001-1-linux@roeck-us.net
[ clg: Renamed machine to 'supermicro-x11spi-bmc' ]
Message-Id: <20221025165109.1226001-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Snapshot loading only expects to call deterministic handlers, not
non-deterministic ones. So introduce a way of registering handlers that
won't be called when reseting for snapshots.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Message-id: 20221025004327.568476-2-Jason@zx2c4.com
[PMM: updated json doc comment with Markus' text; fixed
checkpatch style nit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A mx25l25635f chip model is generally found on these machines. It's
newer and uses 4B opcodes which is better to exercise the support in
the Linux kernel.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-Id: <20220722063602.128144-9-clg@kaod.org>
Message-Id: <20221013161241.2805140-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
For the PVT-class hardware we have increased the memory size of
this device to 2 GiB. Adjust the device model accordingly.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20221007110529.3657749-1-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently armv7m_load_kernel() takes the size of the block of memory
where it should load the initial guest image, but assumes that it
should always load it at address 0. This happens to be true of all
our M-profile boards at the moment, but it isn't guaranteed to always
be so: M-profile CPUs can be configured (via init-svtor and
init-nsvtor, which match equivalent hardware configuration signals)
to have the initial vector table at any address, not just zero. (For
instance the Teeny board has the boot ROM at address 0x0200_0000.)
Add a base address argument to armv7m_load_kernel(), so that
callers now pass in both base address and size. All the current
callers pass 0, so this is not a behaviour change.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220823160417.3858216-3-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fixes: 346160cbf2 ("aspeed: Set the dram container at the SoC level")
Message-Id: <20220727102714.803041-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change moves the code that connects the SoC UART's to serial_hd's
to the machine.
It makes each UART a proper child member of the SoC, and then allows the
machine to selectively initialize the chardev for each UART with a
serial_hd.
This should preserve backwards compatibility, but also allow multi-SoC
boards to completely change the wiring of serial devices from the
command line to specific SoC UART's.
This also removes the uart-default property from the SoC, since the SoC
doesn't need to know what UART is the "default" on the machine anymore.
I tested this using the images and commands from the previous
refactoring, and another test image for the ast1030:
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd
wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd
wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf
Fuji uses UART1:
qemu-system-arm -machine fuji-bmc \
-drive file=fuji.mtd,format=raw,if=mtd \
-nographic
ast2600-evb uses uart-default=UART5:
qemu-system-arm -machine ast2600-evb \
-drive file=fuji.mtd,format=raw,if=mtd \
-serial null -serial mon:stdio -display none
Wedge100 uses UART3:
qemu-system-arm -machine palmetto-bmc \
-drive file=wedge100.mtd,format=raw,if=mtd \
-serial null -serial null -serial null \
-serial mon:stdio -display none
AST1030 EVB uses UART5:
qemu-system-arm -machine ast1030-evb \
-kernel Y35BCL.elf -nographic
Fixes: 6827ff20b2 ("hw: aspeed: Init all UART's with serial devices")
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220705191400.41632-4-peter@pjd.dev>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Swap 'buf' and 'bytes' around for consistency with
blk_co_{pread,pwrite}(), and in preparation to implement these functions
using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pread(blk, offset, buf, bytes, flags)
+ blk_pread(blk, offset, bytes, buf, flags)
@@ expression blk, offset, buf, bytes, flags; @@
- blk_pwrite(blk, offset, buf, bytes, flags)
+ blk_pwrite(blk, offset, bytes, buf, flags)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-4-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For consistency with other I/O functions, and in preparation to
implement it using generated_co_wrapper.
Callers were updated using this Coccinelle script:
@@ expression blk, offset, buf, bytes; @@
- blk_pread(blk, offset, buf, bytes)
+ blk_pread(blk, offset, buf, bytes, 0)
It had no effect on hw/block/nand.c, presumably due to the #if, so that
file was updated manually.
Overly-long lines were then fixed by hand.
Signed-off-by: Alberto Faria <afaria@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220705161527.1054072-3-afaria@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add MAX31785 fan controllers in machines so that the Linux driver
populates the sysfs interface.
Firework has two MAX31785 Fan controllers at 0x52, and 0x54 on bus 9.
Witherspoon has one at 0x52 on bus 3.
Rainier has one at 0x52 on bus 7.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-6-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Multi-SoC machines can use this property to specify a memory container
for each SoC. Single SoC machines will just specify get_system_memory().
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220624003701.1363500-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the Aspeed machines allocate a ram container region in
which the machine ram region is mapped. See commit ad1a978218
("aspeed: add a RAM memory region container"). An extra region is
mapped after ram in the ram container to catch invalid access done by
FW. That's how FW determines the size of ram. See commit ebe31c0a8e
("aspeed: add a max_ram_size property to the memory controller").
Let's move all the logic under the SoC where it should be. It will
also ease the work on multi SoC support.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20220623202123.3972977-1-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Instantiate the I2C buses in AST1030 model and create two slave device
for ast1030-evb.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg : - adapted to current AST1030 upstream models
- changed AST2600 to AST1030 in comment
- fixed typo in commit log ]
Message-Id: <20220324100439.478317-3-troy_lee@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The board has no such device. It might have been useful for some tests
in the past, it's not anymore and the same can be achieved on the
command line.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add EEPROM and LM75 temperature sensor according to hardware schematic
Signed-off-by: Howard Chiu <howard_chiu@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the 'fby35-bmc' machine type based on the kernel DTS[1] and userspace
i2c setup scripts[2]. Undefined values are inherited from the AST2600-EVB.
Reference images can be found in Facebook OpenBMC Github Release assets
as "fby35.mtd". [3]
You can boot the reference images as follows (fby35 uses dual-flash):
qemu-system-arm -machine fby35-bmc \
-drive file=fby35.mtd,format=raw,if=mtd \
-drive file=fby35.mtd,format=raw,if=mtd \
-nographic
[1] 412d505325/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts
[2] e2294ff5d3/meta-facebook/meta-fby35/recipes-fby35/plat-utils/files/setup-dev.sh
[3] https://github.com/facebook/openbmc/releases
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220503225925.1798324-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Current fmc model of AST2500 EVB and AST2600 EVB can't emulate quad
mode properly so fix them using equivalent mx25l25635e and mx66u51235f
respectively.
These default settings still can be overridden using the 'fmc-model'
command line option.
Reported-by: Graeme Gregory <quic_ggregory@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220402184427.4010304-1-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The image should be supplied with ELF binary.
$ qemu-system-arm -M ast1030-evb -kernel zephyr.elf -nographic
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220401083850.15266-9-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the 'bletchley-bmc' machine type based on the kernel DTS[1] and
hardware schematics available to me. The i2c model is as complete as
the current QEMU models support, but in some cases I substituted devices
that are close enough for present functionality. Strap registers are
kept the same as the AST2600-EVB until I'm able to confirm correct
values with physical hardware.
This has been tested with an openbmc image built from [2] plus a kernel
patch[3] for the SPI flash module.
1. https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts?id=a8c729e966c4e9d033242d948b0e53c2a62d32e2
2. b9432b980d
3. 25b566b9a9
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg : increased number of FMC devices to 2 to match Linux dts ]
Message-Id: <20220305000656.1944589-2-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Generally all BMCs will use the fmc_model to hold their own flash
and most will have a spi_model to hold the managed system's flash,
but not all systems do. Add a simple NULL check to allow a system
to set the spi_model as NULL to indicate it should not be instantiated.
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Message-Id: <20220305000656.1944589-1-patrick@stwcx.xyz>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not used anymore.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Currently, the allocation of the flash devices uses the number of
slave selects configured in the SoC realize routine. It is simpler to
use directly the number of FMC devices defined in the machine class
and 1 for spi devices (which is what the SoC does in the back of the
machine).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
A memory chunk is allocated with g_new0() and assigned to the variable
'storage'. However, if the branch takes true, there will be only an
error report but not a free operation for 'storage' before function
returns. As a result, a memory leak bug is triggered.
Use g_autofree to fix the issue.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
[ clg: reworked the commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This unifies the way we create the pca9552 devices on the different boards.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
