The timer controller can be driven by either an external 1MHz clock or
by the APB clock. Today, the model makes the assumption that the APB
frequency is always set to 24MHz but this is incorrect.
The AST2400 SoC on the palmetto machines uses a 48MHz input clock
source and the APB can be set to 48MHz. The consequence is a general
system slowdown. The QEMU machines using the AST2500 SoC do not seem
impacted today because the APB frequency is still set to 24MHz.
We fix the timer frequency for all SoCs by linking the Timer model to
the SCU model. The APB frequency driving the timers is now the one
configured for the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The System Control Unit should be initialized first as it drives all
the configuration of the SoC and other device models.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All Aspeed SoC clocks are driven by an input source clock which can
have different frequencies : 24MHz or 25MHz, and also, on the Aspeed
AST2400 SoC, 48MHz. The H-PLL (CPU) clock is defined from a
calculation using parameters in the H-PLL Parameter register or from a
predefined set of frequencies if the setting is strapped by hardware
(Aspeed AST2400 SoC). The other clocks of the SoC are then defined
from the H-PLL using dividers.
We introduce first the APB clock because it should be used to drive
the Aspeed timer model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On TLB invalidation commands, let's call registered
IOMMU notifiers. Those can only be UNMAP notifiers.
SMMUv3 does not support notification on MAP (VFIO).
This patch allows vhost use case where IOTLB API is notified
on each guest IOTLB invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We emulate a TLB cache of size SMMU_IOTLB_MAX_SIZE=256.
It is implemented as a hash table whose key is a combination
of the 16b asid and 48b IOVA (Jenkins hash).
Entries are invalidated on TLB invalidation commands, either
globally, or per asid, or per asid/iova.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1529653501-15358-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's cache config data to avoid fetching and parsing STE/CD
structures on each translation. We invalidate them on data structure
invalidation commands.
We put in place a per-smmu mutex to protect the config cache. This
will be useful too to protect the IOTLB cache. The caches can be
accessed without BQL, ie. in IO dataplane. The same kind of mutex was
put in place in the intel viommu.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In case the STE's config is "Bypass" we currently don't set the
IOMMUTLBEntry perm flags and the access does not succeed. Also
if the config is 0b0xx (Aborted/Reserved), decode_ste and
smmuv3_decode_config currently returns -EINVAL and we don't enter
the expected code path: we record an event whereas we should not.
This patch fixes those bugs and simplifies the error handling.
decode_ste and smmuv3_decode_config now return 0 if aborted or
bypassed config was found. Only bad config info produces negative
error values. In smmuv3_translate we more clearly differentiate
errors, bypass/smmu disabled, aborted and success cases. Also
trace points are differentiated.
Fixes: 9bde7f0674 ("hw/arm/smmuv3: Implement translate callback")
Reported-by: jia.he@hxt-semitech.com
Signed-off-by: jia.he@hxt-semitech.com
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-17-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Missed in df3692e04b.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-16-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw_error() finally calls abort(), but there is no need to abort here.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-14-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw_error() finally calls abort(), but there is no need to abort here.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-13-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180624040609.17572-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TCMI_VERBOSE is no more used, drop the OMAP_8/16/32B_REG macros.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180624040609.17572-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Qspi dma has a burst length of 64 bytes, So limit the transactions w.r.t
dma-burst-size property.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1529660880-30376-1-git-send-email-sai.pavan.boddu@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also handle the fake transfers for dummy bytes in this setup
routine. It will be useful when we activate MMIO execution.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only the flash type is strapped by HW. The 4BYTE mode is set by
firmware when the flash device is detected.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When configured in dual I/O mode, address and data are sent in dual
mode, including the dummy byte cycles in between. Adapt the count to
the IO setting.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180612065716.10587-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
> CID 1393621: (OVERFLOW_BEFORE_WIDEN)
> Potentially overflowing expression "stride * s->height" with type "unsigned
> int" (32 bits, unsigned) is evaluated using +32-bit arithmetic, and then used
> in a context that expects an expression of type "hwaddr" (64 bits, unsigned).
Fix by changing stride from uint32_t to hwaddr.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180626083120.19515-1-kraxel@redhat.com
This makes sure the regions are properly cleaned when unplugging -device
seconday-vga.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180626060941.8326-1-kraxel@redhat.com
The "I" bit in PIO Setup and D2H FISes is exclusively a device concept
and the irqstatus register in the controller does not matter. The SATA
spec says when it should be one; for D2H FISes in practice it is always
set, while the PIO Setup FIS has several subcases that are documented in
the patch.
Also, the PIO Setup FIS interrupt is actually generated _after_ data
has been received.
Someone should probably spend some time reading the SATA specification and
figuring out the more obscure fields in the PIO Setup FIS, but this is enough
to fix SeaBIOS booting from ATAPI CD-ROMs over an AHCI controller.
Fixes: 956556e131
Reported-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180622165159.19863-1-pbonzini@redhat.com
[Minor edit to avoid ATAPI comment ambiguity. --js]
Signed-off-by: John Snow <jsnow@redhat.com>
The oldest machine type which is still used in a still maintained distro
is a pc-0.12 based machine type in RHEL6, so everything that is older
than pc-0.12 should not be used anymore. Thus let's deprecate pc-0.10
and pc-0.11 so that we can finally remove them in a future release.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1529917512-10528-1-git-send-email-thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Also add a compat property to disable it for old machine types,
needed for live migration compatibility.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-6-kraxel@redhat.com
If some event caused some larger playback hickup the fine-grained timer
adjust isn't able to recover. Use a buffer overruns as indicator for
that. Reset timer adjust logic in case we detected one.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-5-kraxel@redhat.com
We have some jitter in the audio timer call frequency and buffer sizes.
So it is rather pointless trying to be very exact, effect is a constant
up+down adjustment. So adjust only in case we are off too much.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-4-kraxel@redhat.com
Currently, the HDA device tries to sync itself with the QEMU audio
backend by waiting for the guest driver to handle buffer completion
interrupts. This causes the backend to often read too much data from the
device, as well as running out of data whenever the guest takes too long
to handle the interrupt.
According to the HDA specification, the guest is also not required to
use interrupts, but can also sync itself by polling the LPIB registers.
This patch will introduce high frequency (1000Hz) timers that interface
with the device and allow for much smoother emulation of the LPIB
registers. Since the timing is now provided by these timers, the need
to wait for buffer completion interrupts also ceases.
Signed-off-by: Martin Schrodt <martin@schrodt.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180622111200.30561-2-kraxel@redhat.com
Message-id: 20171015184033.2951-3-martin@schrodt.org
[ kraxel: keep old code for compatibility with older qemu versions,
add property to switch code paths at runtime ]
[ kraxel: new code is disabled by default, use-timer=on enables it ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1T5q
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20180622' into staging
target-arm queue:
* hw/intc/arm_gicv3: fix wrong values when reading IPRIORITYR
* target/arm: fix read of freed memory in kvm_arm_machine_init_done()
* virt: support up to 512 CPUs
* virt: support 256MB ECAM PCI region (for more PCI devices)
* xlnx-zynqmp: Use Cortex-R5F, not Cortex-R5
* mps2-tz: Implement and use the TrustZone Memory Protection Controller
* target/arm: enforce alignment checking for v6M cores
* xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
* vl.c: Don't zero-initialize statics for serial_hds
# gpg: Signature made Fri 22 Jun 2018 13:56:00 BST
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20180622: (28 commits)
xen: Don't use memory_region_init_ram_nomigrate() in pci_assign_dev_load_option_rom()
vl.c: Don't zero-initialize statics for serial_hds
target/arm: Strict alignment for ARMv6-M and ARMv8-M Baseline
target/arm: Introduce ARM_FEATURE_M_MAIN
hw/arm/mps2-tz.c: Instantiate MPCs
hw/arm/iotkit: Wire up MPC interrupt lines
hw/arm/iotkit: Instantiate MPC
hw/misc/iotkit-secctl.c: Implement SECMPCINTSTATUS
hw/misc/tz_mpc.c: Honour the BLK_LUT settings in translate
hw/misc/tz-mpc.c: Implement correct blocked-access behaviour
hw/misc/tz-mpc.c: Implement registers
hw/misc/tz-mpc.c: Implement the Arm TrustZone Memory Protection Controller
xlnx-zynqmp: Swap Cortex-R5 for Cortex-R5F
target-arm: Add the Cortex-R5F
hw/arm/virt: Increase max_cpus to 512
hw/arm/virt: Use 256MB ECAM region by default
hw/arm/virt: Add virt-3.0 machine type
hw/arm/virt: Add a new 256MB ECAM region
hw/arm/virt: Register two redistributor regions when necessary
hw/arm/virt-acpi-build: Advertise one or two GICR structures
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The xen pci_assign_dev_load_option_rom() currently creates a RAM
memory region with memory_region_init_ram_nomigrate(), and then
manually registers it with vmstate_register_ram(). In fact for
its only callsite, the 'owner' pointer we use for the init call
and the '&dev->qdev' pointer we use for the vmstate_register_ram()
call refer to the same object. Simplify the function to only
take a pointer to the device once instead of twice, and use
memory_region_init_ram() which automatically does the vmstate
register for us.
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate and wire up the Memory Protection Controllers
in the MPS2 board itself.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-9-peter.maydell@linaro.org
The interrupt outputs from the MPC in the IoTKit and the expansion
MPCs in the board must be wired up to the security controller, and
also all ORed together to produce a single line to the NVIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-8-peter.maydell@linaro.org
Wire up the one MPC that is part of the IoTKit itself. For the
moment we don't wire up its interrupt line.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-7-peter.maydell@linaro.org
Implement the SECMPCINTSTATUS register. This is the only register
in the security controller that deals with Memory Protection
Controllers, and it simply provides a read-only view of the
interrupt lines from the various MPCs in the system.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180620132032.28865-6-peter.maydell@linaro.org
The final part of the Memory Protection Controller we need to
implement is actually using the BLK_LUT data programmed by the
guest to determine whether to block the transaction or not.
Since this means we now change transaction mappings when
the guest writes to BLK_LUT, we must also call the IOMMU
notifiers at that point.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-5-peter.maydell@linaro.org
The MPC is guest-configurable for whether blocked accesses:
* should be RAZ/WI or cause a bus error
* should generate an interrupt or not
Implement this behaviour in the blocked-access handlers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-4-peter.maydell@linaro.org
Implement the missing registers for the TZ MPC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-3-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
The ZynqMP has Cortex-R5Fs with the optional FPU enabled.
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180529124707.3025-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virt 3.0 now allows up to 512 vcpus whereas for earlier machine
types, max_cpus was set to 255 and any attempt to start the
machine with vcpus > 255 was rejected at a very early stage,
in vl.c/main level.
512 is the max supported by KVM. Anyway the actual vcpu count
that can be achieved depends on other parameters such as the
acceleration mode, the vgic version, the host kernel version.
Those are discovered later on.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-12-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this patch, virt-3.0 machine uses a new 256MB ECAM region
by default instead of the legacy 16MB one, if highmem is set
(LPAE supported by the guest) and (!firmware_loaded || aarch64).
Indeed aarch32 mode FW may not support this high ECAM region.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-11-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With a VGICv3 KVM device, if the number of vcpus exceeds the
capacity of the legacy redistributor region (123 redistributors),
we now attempt to register a second redistributor region. Up to
512 redistributors can fit in this latter on top of the 123 allowed
by the legacy redistributor region.
Registering this second redistributor region is possible if the
host kernel supports the following VGICv3 KVM device group/attribute:
KVM_DEV_ARM_VGIC_GRP_ADDR/KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION.
In case the host kernel does not support the registration of several
redistributor regions and the requested number of vcpus exceeds the
capacity of the legacy redistributor region, the GICv3 device
initialization fails with a proper error message and qemu exits.
At the moment the max number of vcpus still is capped by the
virt machine class max_cpus.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-8-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Depending on the number of smp_cpus we now register one or two
GICR structures.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-7-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the creation of a GICv3 node with 1 or 2
redistributor regions depending on the number of smu_cpus.
The second redistributor region is located just after the
existing RAM region, at 256GB and contains up to up to 512 vcpus.
Please refer to kernel documentation for further node details:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-6-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's check if KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION is supported.
If not, we check the number of redist region is equal to 1 and use the
legacy KVM_VGIC_V3_ADDR_TYPE_REDIST attribute. Otherwise we use
the new attribute and allow to register multiple regions to the
KVM device.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
for KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION attribute, the attribute
data pointed to by kvm_device_attr.addr is a OR of the
redistributor region address and other fields such as the index
of the redistributor region and the number of redistributors the
region can contain.
The existing machine init done notifier framework sets the address
field to the actual address of the device and does not allow to OR
this value with other fields.
This patch extends the KVMDevice struct with a new kda_addr_ormask
member. Its value is passed at registration time and OR'ed with the
resolved address on kvm_arm_set_device_addr().
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529072910-16156-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When either GICD_IPRIORITYR or GICR_IPRIORITYR is read as a 32-bit
register, the post left-shift operator in the for loop causes an
extra shift after the least significant byte has been placed.
The 32-bit value actually returned is therefore the expected value
shifted left by 8 bits.
Signed-off-by: Amol Surati <suratiamol@gmail.com>
Message-id: 20180614054857.26248-1-suratiamol@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently during KVM initialization on POWER, kvm_fixup_page_sizes()
rewrites a bunch of information in the cpu state to reflect the
capabilities of the host MMU and KVM. This overwrites the information
that's already there reflecting how the TCG implementation of the MMU will
operate.
This means that we can get guest-visibly different behaviour between KVM
and TCG (and between different KVM implementations). That's bad. It also
prevents migration between KVM and TCG.
The pseries machine type now has filtering of the pagesizes it allows the
guest to use which means it can present a consistent model of the MMU
across all accelerators.
So, we can now replace kvm_fixup_page_sizes() with kvm_check_mmu() which
merely verifies that the expected cpu model can be faithfully handled by
KVM, rather than updating the cpu model to match KVM.
We call kvm_check_mmu() from the spapr cpu reset code. This is a hack:
conceptually it makes more sense where fixup_page_sizes() was - in the KVM
cpu init path. However, doing that would require moving the platform's
pagesize filtering much earlier, which would require a lot of work making
further adjustments. There wouldn't be a lot of concrete point to doing
that, since the only KVM implementation which has the awkward MMU
restrictions is KVM HV, which can only work with an spapr guest anyway.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
KVM HV has some limitations (deriving from the hardware) that mean not all
host-cpu supported pagesizes may be usable in the guest. At present this
means that KVM guests and TCG guests may see different available page sizes
even if they notionally have the same vcpu model. This is confusing and
also prevents migration between TCG and KVM.
This patch makes the environment consistent by always allowing the same set
of pagesizes. Since we can't remove the KVM limitations, we do this by
always applying the same limitations it has, even to TCG guests.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way we used to handle KVM allowable guest pagesizes for PAPR guests
required some convoluted checking of memory attached to the guest.
The allowable pagesizes advertised to the guest cpus depended on the memory
which was attached at boot, but then we needed to ensure that any memory
later hotplugged didn't change which pagesizes were allowed.
Now that we have an explicit machine option to control the allowable
maximum pagesize we can simplify this. We just check all memory backends
against that declared pagesize. We check base and cold-plugged memory at
reset time, and hotplugged memory at pre_plug() time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way the POWER Hash Page Table (HPT) MMU is virtualized by KVM HV means
that every page that the guest puts in the pagetables must be truly
physically contiguous, not just GPA-contiguous. In effect this means that
an HPT guest can't use any pagesizes greater than the host page size used
to back its memory.
At present we handle this by changing what we advertise to the guest based
on the backing pagesizes. This is pretty bad, because it means the guest
sees a different environment depending on what should be host configuration
details.
As a start on fixing this, we add a new capability parameter to the
pseries machine type which gives the maximum allowed pagesizes for an
HPT guest. For now we just create and validate the parameter without
making it do anything.
For backwards compatibility, on older machine types we set it to the max
available page size for the host. For the 3.0 machine type, we fix it to
16, the intention being to only allow HPT pagesizes up to 64kiB by default
in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't emulate slave mode so related registers are not needed.
[lh]sadr are only retained to avoid too many warnings and simplify
debugging but sdata is not even correct because device has a 4 byte
FIFO instead so just remove this unimplemented register for now.
The intr register is also not implemented correctly, it is for
diagnostics and normally not even visible on device without explicitly
enabling it. As no guests are known to need this remove it as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the sm501 specs the hardware cursor colors are to be given in
the rgb565 format, but the code currently interprets them as bgr565.
Therefore, the colors of the hardware cursors are wrong in the QEMU
display, e.g., the standard mouse pointer of AmigaOS appears blue instead
of red. This change fixes this issue by replacing the existing naive
bgr565 => rgb888 conversion with a standard rgb565 => rgb888 one that also
scales the color component values properly.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_irq_alloc_block and spapr_irq_alloc() are now deprecated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, when a device requests for IRQ number in a sPAPR machine, the
spapr_irq_alloc() routine first scans the ICSState status array to
find an empty slot and then performs the assignement of the selected
numbers. Split this sequence in two distinct routines : spapr_irq_find()
for lookups and spapr_irq_claim() for claiming the IRQ numbers.
This will ease the introduction of a static layout of IRQ numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr capabilities have an apply hook to actually activate (or deactivate)
the feature in the system at reset time. However, a number of capabilities
affect the setup of cpus, and need to be applied to each of them -
including hotplugged cpus for extra complication. To make this simpler,
add an optional cpu_apply hook that is called from spapr_cpu_reset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Previously, the effective values of the various spapr capability flags
were only determined at machine reset time. That was a lazy way of making
sure it was after cpu initialization so it could use the cpu object to
inform the defaults.
But we've now improved the compat checking code so that we don't need to
instantiate the cpus to use it. That lets us move the resolution of the
capability defaults much earlier.
This is going to be necessary for some future capabilities.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
ppc_check_compat() is used in a number of places to check if a cpu object
supports a certain compatiblity mode, subject to various constraints.
It takes a PowerPCCPU *, however it really only depends on the cpu's class.
We have upcoming cases where it would be useful to make compatibility
checks before we fully instantiate the cpu objects.
ppc_type_check_compat() will now make an equivalent check, but based on a
CPU's QOM typename instead of an instantiated CPU object.
We make use of the new interface in several places in spapr, where we're
essentially making a global check, rather than one specific to a particular
cpu. This avoids some ugly uses of first_cpu to grab a "representative"
instance.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The device tree node of the ISA bus was being partially done in
different places. Move all the nodes creation under the same routine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU implements the "Shared Processor LPAR" (SPLPAR) option, which allows
the hypervisor to time-slice a physical processor into multiple virtual
processor. The intent is to allow more guests to run, and to optimize
processor utilization.
The guest OS can cede idle VCPUs, so that their processing capacity may
be used by other VCPUs, with the H_CEDE hcall. The guest OS can also
optimize spinlocks, by confering the time-slice of a spinning VCPU to the
spinlock holder if it's currently notrunning, with the H_CONFER hcall.
Both hcalls depend on a "Virtual Processor Area" (VPA) to be registered
by the guest OS, generally during early boot. Other per-VCPU areas can
be registered: the "SLB Shadow Buffer" which allows a more efficient
dispatching of VCPUs, and the "Dispatch Trace Log Buffer" (DTL) which
is used to compute time stolen by the hypervisor. Both DTL and SLB Shadow
areas depend on the VPA to be registered.
The VPA/SLB Shadow/DTL are state that QEMU should migrate, but this doesn't
happen, for no apparent reason other than it was just never coded. This
causes the features listed above to stop working after migration, and it
breaks the logic of the H_REGISTER_VPA hcall in the destination.
The VPA is set at the guest request, ie, we don't have to migrate
it before the guest has actually set it. This patch hence adds an
"spapr_cpu/vpa" subsection to the recently introduced per-CPU machine
data migration stream.
Since DTL and SLB Shadow are optional and both depend on VPA, they get
their own subsections "spapr_cpu/vpa/slb_shadow" and "spapr_cpu/vpa/dtl"
hanging from the "spapr_cpu/vpa" subsection.
Note that this won't break migration to older QEMUs. Is is already handled
by only registering the vmstate handler for per-CPU data with newer machine
types.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A per-CPU machine data pointer was recently added to PowerPCCPU. The
motivation is to to hide platform specific details from the core CPU
code. This per-CPU data can hold state which is relevant to the guest
though, eg, Virtual Processor Areas, and we should migrate this state.
This patch adds the plumbing so that we can migrate the per-CPU data
for PAPR guests. We only do this for newer machine types for the sake
of backward compatibility. No state is migrated for the moment: the
vmstate_spapr_cpu_state structure will be populated by subsequent
patches.
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fix some trivial spelling and spacing errors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- accommodate guests using vfio-ccw without specifying unlimited
prefetch, but actually working fine
- add cpu model for the z14 Model ZR1
- add support for pxelinux.cfg-style network booting to the s390x
firmware
-----BEGIN PGP SIGNATURE-----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=hMax
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180619' into staging
- cleanup in virtio-ccw
- accommodate guests using vfio-ccw without specifying unlimited
prefetch, but actually working fine
- add cpu model for the z14 Model ZR1
- add support for pxelinux.cfg-style network booting to the s390x
firmware
# gpg: Signature made Tue 19 Jun 2018 10:33:06 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180619:
pc-bios/s390-ccw: Update the s390-netboot.img binary
pc-bios/s390-ccw: Optimize the s390-netboot.img for size
pc-bios/s390-ccw/net: Try to load pxelinux.cfg file accoring to the UUID
pc-bios/s390-ccw/net: Add support for pxelinux-style config files
pc-bios/s390-ccw/net: Update code for the latest changes in SLOF
roms: Update SLOF submodule to current status
pc-bios/s390-ccw: define loadparm length
s390x/cpumodels: add z14 Model ZR1
s390x/ipl: Try to detect Linux vs non Linux for initial IPL PSW
vfio-ccw: remove orb.c64 (64 bit data addresses) check
vfio-ccw: add force unlimited prefetch property
virtio-ccw: clean up notify
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 802cbcb730, most issues have been fixed when qemu guest
migration. But the queue size still need to check whether is equal to
PS2_QUEUE_SIZE. If yes, the wptr should set as 0. Or, wptr would larger
than PS2_QUEUE_SIZE and never come back when ps2_queue_noirq is called.
This could lead to OOB access, add check to avoid it.
Signed-off-by: liujunjie <liujunjie23@huawei.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 20180607080237.12360-1-liujunjie23@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Right now the IPL device always starts from address 0x10000 (the usual
Linux entry point). To run other guests (e.g. test programs) it is
useful to use the IPL PSW from address 0. We can use the Linux magic
at 0x10008 to decide.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20180612125933.262679-1-borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The vfio-ccw module does the check too, and there is actually no
technical obstacle for supporting fmt 1 idaws. Let us be ready for the
beautiful day when fmt 1 idaws become supported by the vfio-ccw kernel
module. QEMU does not have to do a thing for that, except not insisting
on this check.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Jason J. Herne <jjherne@linux.ibm.com>
Tested-by: Jason J. Herne <jjherne@linux.ibm.com>
Message-Id: <20180524175828.3143-3-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
There is at least one guest (OS) such that although it does not rely on
the guarantees provided by ORB 1 word 9 bit (aka unlimited prefetch, aka
P bit) not being set, it fails to tell this to the machine.
Usually this ain't a big deal, as the original purpose of the P bit is to
allow for performance optimizations. vfio-ccw however can not provide the
guarantees required if the bit is not set.
It is not possible to implement support for the P bit not set without
transitioning to lower level protocols for vfio-ccw. So let's give the
user the opportunity to force setting the P bit, if the user knows this
is safe. For self modifying channel programs forcing the P bit is not
safe. If the P bit is forced for a self modifying channel program things
are expected to break in strange ways.
Let's also avoid warning multiple about P bit not set in the ORB in case
P bit is not told to be forced, and designate the affected vfio-ccw
device.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Suggested-by: Dong Jia Shi <bjsdjshi@linux.ibm.com>
Acked-by: Jason J. Herne <jjherne@linux.ibm.com>
Tested-by: Jason J. Herne <jjherne@linux.ibm.com>
Message-Id: <20180524175828.3143-2-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Coverity recently started complaining about virtio_ccw_notify(). Turns
out, there is a couple of things that can be cleaned up. Let's clean!
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: CID 1390619
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20180516132757.68558-1-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This is wrong. object_finalize_child_property()'s unref balances the
ref in object_property_add_child(). qbus_realize's unref balances the
ref that was initially placed by object_new/object_initialize.
This reverts commit f3d58385a6.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The USB device don't hold the bus. There is no ASAN related reports
anymore.
This reverts commit cd7bc87868.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bus is not owned by the device.
This reverts commit 410a096adf.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 3d85885a1b tried to fix error handling, but it actually
went into the wrong direction by dropping the local Error *.
In the default KVM case, the rationale is to try the in-kernel XICS first,
and if not possible, to fallback to userland XICS. Passing errp everywhere
makes this fallback impossible if errp is &error_fatal (which happens to
be the case). And anyway, if the caller would pass a regular &local_err,
things would be worse: we could possibly pass an already set *errp to
error_setg() and crash, or return an error even in case of success.
So we definitely need a local Error * and only propagate it when we're
done with the fallback logic. This is what this patch does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The instance_init function of devices should always succeed to be able
to introspect the device. However, the instance_init function of the
"openprom" device can currently fail, for example like this:
$ echo "{'execute':'qmp_capabilities'}"\
"{'execute':'device-list-properties',"\
" 'arguments':{'typename':'openprom'}}" \
| sparc64-softmmu/qemu-system-sparc64 -M sun4v,accel=qtest -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 91, "minor": 11, "major": 2},
"package": "build-all"}, "capabilities": []}}
{"return": {}}
RAMBlock "sun4u.prom" already registered, abort!
Aborted (core dumped)
This should not happen. Fix this problem by moving the affected code from
instance_init into a realize function instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
On the Alpha DP264 machine, the Cirrus VGA is I/O mapped
in the 3C0H-3CFH range, thus I/O base used by the parallel
device clashes, and since a4cb773928 the VGA is not
working:
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
00000801fc000000-00000801fdffffff (prio 0, i/o): pci0-io
...
00000801fc0003b4-00000801fc0003b5 (prio 0, i/o): vga
00000801fc0003ba-00000801fc0003ba (prio 0, i/o): vga
00000801fc0003bc-00000801fc0003c3 (prio 0, i/o): parallel
^^^ ^^^^^^^^
00000801fc0003c0-00000801fc0003cf (prio 0, i/o): vga
^^^
00000801fc0003d4-00000801fc0003d5 (prio 0, i/o): vga
00000801fc0003da-00000801fc0003da (prio 0, i/o): vga
...
As there is no particular reason to use this base address
(introduced in 7bea0dd434), change to 378H which is the
default on PC machines.
Reported-by: Emilio G. Cota <cota@braap.org>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180614233935.26585-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
This extracts from the PvChip realize routine the part creating the
cores. On Power9, we will need to create the cores after the Xive
interrupt controller is created.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves some code out from spapr_cpu_core_realize() for clarity. No
functional change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_realize_vcpu() function doesn't rollback in case of error.
This isn't a problem with coldplugged CPUs because the machine won't
start and QEMU will exit. Hotplug is a different story though: the
CPU thread is started under object_property_set_bool() and it assumes
it can access the CPU object.
If icp_create() fails, we return an error without unregistering the
reset handler for this CPU, and we let the underlying QEMU thread for
this CPU alive. Since spapr_cpu_core_realize() doesn't care to unrealize
already realized CPUs either, but happily frees all of them anyway, the
CPU thread crashes instantly:
(qemu) device_add host-spapr-cpu-core,core-id=1,id=gku
GKU: failing icp_create (cpu 0x11497fd0)
^^^^^^^^^^
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fffee3feaa0 (LWP 24725)]
0x00000000104c8374 in object_dynamic_cast_assert (obj=0x11497fd0,
^^^^^^^^^^^^^^
pointer to the CPU object
623 trace_object_dynamic_cast_assert(obj ? obj->class->type->name
(gdb) p obj->class->type
$1 = (Type) 0x0
(gdb) p * obj
$2 = {class = 0x10ea9c10, free = 0x11244620,
^^^^^^^^^^
should be g_free
(gdb) p g_free
$3 = {<text variable, no debug info>} 0x7ffff282bef0 <g_free>
obj is a dangling pointer to the CPU that was just destroyed in
spapr_cpu_core_realize().
This patch adds proper rollback to both spapr_realize_vcpu() and
spapr_cpu_core_realize().
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fixed a conflict due to a change in my tree]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 94ad93bd97 (QEMU 2.12) switched to instantiate CPUs separately
but it missed to adapt the error path accordingly. If something fails in
the CPU creation loop, then the CPU object that was just created is leaked.
The error paths in this function are a bit obfuscated, and adding
yet another label to free this CPU object makes it worse. We should
move the block of the loop to a separate function, with a proper
rollback path, but this is a bigger cleanup.
For now, let's just fix the bug by adding the missing calls to
object_unref(). This will allow easier backport to older QEMU
versions.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently we don't have any unrealize path for pnv cpu cores. We get away
with this because we don't yet support cpu hotplug for pnv.
However, we're going to want it eventually, and in the meantime, it makes
it non-obvious why there are a bunch of allocations on the realize() path
that don't have matching frees.
So, implement the missing unrealize path.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
pnv_cpu_init() is only called from the the pnv cpu core realize path, and
really only can be called from there. So fold it into its caller, which
we also rename for brevity.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
In pnv_core_realize() we call two functions with an Error * parameter in
succession, which will go badly if they both cause errors. In fact, a
failure in either of them indicates a qemu internal error, so we can just
use &error_abort in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
spapr_cpu_init() and spapr_cpu_destroy() are only called from the spapr
cpu core realize/unrealize paths, and really can only be called from there.
Those are all short functions, so fold the pairs together for simplicity.
While we're there rename some functions and change some parameter types
for brevity and clarity.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
When writing registers that have read only bits we have to avoid
changing these bits as they may have non zero values. Make sure we use
the correct masks to mask out read only and reserved bits when
changing registers.
Also remove extra spaces from dram_control and arbitration_control
assignments.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In the case where we have an interrupt generated externally from inputs to
bits 1 and 2 of port A and/or port B, it is necessary to expose
mos6522_update_irq() so it can be called by the interrupt source.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The datasheet indicates that the interrupt is generated by ANDing the
interrupt flags register (IFR) with the interrupt enable register (IER)
but currently there is an extra filter for the SR and timer interrupts.
Remove this extra filter to allow interrupts to be generated by external
inputs on bits 1 and 2 of ports A and B.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the 6522 datasheet the shift register (SR) interrupt flag is
cleared upon write with no mention of any other interrupt flags.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On CentOS 7.5, gcc-4.8.5-28.el7_5.1.ppc64le fails to build QEMU due to :
hw/intc/xics_kvm.c: In function ‘ics_set_kvm_state’:
hw/intc/xics_kvm.c:281:13: error: ‘ret’ may be used uninitialized in this
function [-Werror=maybe-uninitialized]
return ret;
Fix the breakage and also remove the extra error reporting as
kvm_device_access() already provides a substantial error message.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MacOS 9 has a bug in its PMU driver whereby after configuring the ADB bus
devices it sends another write to reg 3 on both devices resetting them
both back to the same address.
Add a new disable_direct_reg3_writes property to ADBDevice to disable these
direct writes which can enabled just for the upcoming pmu-adb support.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the Apple ADB documentation, register 3 is a 2-byte register
with the device address in the first byte, and the handler ID in the second
byte.
This is currently the opposite away to which QEMU returns them so switch the
order around.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The programmer switch is wired up via an external GPIO pin and can be used
to aid debugging Mac guests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This option allows the VIA configuration to be controlled between 3
different possible setups: cuda, pmu-adb and pmu with USB rather than ADB
keyboard/mouse.
For the moment we don't do anything with the configuration except to pass
it to the macio device (the via-cuda parent) and also to the firmware via
the fw_cfg interface so that it can present the correct device tree.
The default is cuda which is the current default and so will have no
change in behaviour.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is in preparation for adding configuration controlled via machine
options.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If the negotiated compat mode can't be set, but raw mode is supported,
we decide to ignore the error. An so, we should free it to prevent a
memory leak.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In default_caps_with_cpu() we set spapr_cap_cfpc to broken for POWER8
processors and before.
Since we no longer require private l1d cache on POWER8 for this cap to
be set to workaround change this to default to broken for POWER7
processors and before.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
-----BEGIN PGP SIGNATURE-----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=LxgF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
# gpg: Signature made Fri 15 Jun 2018 15:20:03 BST
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (26 commits)
block: Remove dead deprecation warning code
block: Remove deprecated -drive option serial
block: Remove deprecated -drive option addr
block: Remove deprecated -drive geometry options
rbd: New parameter key-secret
rbd: New parameter auth-client-required
block: Fix -blockdev / blockdev-add for empty objects and arrays
check-block-qdict: Cover flattening of empty lists and dictionaries
check-block-qdict: Rename qdict_flatten()'s variables for clarity
block-qdict: Simplify qdict_is_list() some
block-qdict: Clean up qdict_crumple() a bit
block-qdict: Tweak qdict_flatten_qdict(), qdict_flatten_qlist()
block-qdict: Simplify qdict_flatten_qdict()
block: Make remaining uses of qobject input visitor more robust
block: Factor out qobject_input_visitor_new_flat_confused()
block: Clean up a misuse of qobject_to() in .bdrv_co_create_opts()
block: Fix -drive for certain non-string scalars
block: Fix -blockdev for certain non-string scalars
qobject: Move block-specific qdict code to block-qdict.c
block: Add block-specific QDict header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an IOMMU index argument to the translate method of
IOMMUs. Since all of our current IOMMU implementations
support only a single IOMMU index, this has no effect
on the behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-4-peter.maydell@linaro.org
Add support for multiple IOMMU indexes to the IOMMU notifier APIs.
When initializing a notifier with iommu_notifier_init(), the caller
must pass the IOMMU index that it is interested in. When a change
happens, the IOMMU implementation must pass
memory_region_notify_iommu() the IOMMU index that has changed and
that notifiers must be called for.
IOMMUs which support only a single index don't need to change.
Callers which only really support working with IOMMUs with a single
index can use the result of passing MEMTXATTRS_UNSPECIFIED to
memory_region_iommu_attrs_to_index().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-3-peter.maydell@linaro.org
On Macronix chips, two bytes can written to the WRSR. First byte will
configure the status register and the second the configuration
register. It is important to save the configuration value as it
contains the dummy cycle setting when using dual or quad IO mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ASPEED SoCs contain a single register that returns random data when
read. This models that register so that guests can use it.
The random number data register has a corresponding control register,
however it returns data regardless of the state of the enabled bit, so
the model follows this behaviour.
When the qcrypto call fails we exit as the guest uses the random number
device to feed it's entropy pool, which is used for cryptographic
purposes.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180613114836.9265-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the IoTKit MPC support, we need to wire together the
interrupt outputs of 17 MPCs; this exceeds the current
value of MAX_OR_LINES. Increase MAX_OR_LINES to 32 (which
should be enough for anyone).
The tricky part is retaining the migration compatibility for
existing OR gates; we add a subsection which is only used
for larger OR gates, and define it such that we can freely
increase MAX_OR_LINES in future (or even move to a dynamically
allocated levels[] array without an upper size limit) without
breaking compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-10-peter.maydell@linaro.org
The Cortex-M CPU and its NVIC are two intimately intertwined parts of
the same hardware; it is not possible to use one without the other.
Unfortunately a lot of our board models don't do any sanity checking
on the CPU type the user asks for, so a command line like
qemu-system-arm -M versatilepb -cpu cortex-m3
will create an M3 without an NVIC, and coredump immediately.
In the other direction, trying a non-M-profile CPU in an M-profile
board won't blow up, but doesn't do anything useful either:
qemu-system-arm -M lm3s6965evb -cpu arm926
Add some checking in the NVIC and CPU realize functions that the
user isn't trying to use an NVIC without an M-profile CPU or
an M-profile CPU without an NVIC, so we can produce a helpful
error message rather than a core dump.
Fixes: https://bugs.launchpad.net/qemu/+bug/1766896
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601160355.15393-1-peter.maydell@linaro.org
Remove the now-unused armv7m_init() function. This was a legacy from
before we properly QOMified ARMv7M, and it has some flaws:
* it combines work that needs to be done by an SoC object (creating
and initializing the TYPE_ARMV7M object) with work that needs to
be done by the board model (setting the system up to load the ELF
file specified with -kernel)
* TYPE_ARMV7M creation failure is fatal, but an SoC object wants to
arrange to propagate the failure outward
* it uses allocate-and-create via qdev_create() whereas the current
preferred style for SoC objects is to do creation in-place
Board and SoC models can instead do the two jobs this function
was doing themselves, in the right places and with whatever their
preferred style/error handling is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601144328.23817-3-peter.maydell@linaro.org
The stellaris board is still using the legacy armv7m_init() function,
which predates conversion of the ARMv7M into a proper QOM container
object. Make the board code directly create the ARMv7M object instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601144328.23817-2-peter.maydell@linaro.org
Convert the parallel device away from using the old_mmio field
of MemoryRegionOps. This change only affects the memory-mapped
variant, which is used by the MIPS Jazz boards 'magnum' and 'pica61'.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601141223.26630-7-peter.maydell@linaro.org
Convert the pckbd device away from using the old_mmio field
of MemoryRegionOps. This change only affects the memory-mapped
variant of the i8042, which is used by the Unicore32 'puv3'
board and the MIPS Jazz boards 'magnum' and 'pica61'.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601141223.26630-6-peter.maydell@linaro.org
Convert the wdt_i6300esb device away from using the old_mmio field
of MemoryRegionOps.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601141223.26630-5-peter.maydell@linaro.org
Convert the pflash_cfi02 device away from using the old_mmio field
of MemoryRegionOps.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Max Reitz <mreitz@redhat.com>
Message-id: 20180601141223.26630-4-peter.maydell@linaro.org
Convert the mcf5206 device away from using the old_mmio field
of MemoryRegionOps. This device is used by the an5206 board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Thomas Huth <huth@tuxfamily.org>
Message-id: 20180601141223.26630-3-peter.maydell@linaro.org
Convert the sh7750 device away from using the old_mmio field
of MemoryRegionOps. This device is used by the sh4 r2d board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601141223.26630-2-peter.maydell@linaro.org
The ethernet controller in the AN505 MPC FPGA image is behind
the same AHB Peripheral Protection Controller that handles
the graphics and GPIOs. (In the documentation this is clear
in the block diagram but the ethernet controller was omitted
from the table listing devices connected to the PPC.)
The ethernet sits behind AHB PPCEXP0 interface 5. We had
incorrectly claimed that this was a "gpio4", but there are
only 4 GPIOs in this image.
Correct the QEMU model to match the hardware.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180515171446.10834-1-peter.maydell@linaro.org
While for_each_dist_irq_reg loop starts from GIC_INTERNAL, it forgot to
offset the date array and index. This will overlap the GICR registers
value and leave the last GIC_INTERNAL irq's registers out of update.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
The -drive options cyls, heads, secs and trans were deprecated in
QEMU 2.10. It's time to remove them.
hd-geo-test tested both the old version with geometry options in -drive
and the new one with -device. Therefore the code using -drive doesn't
have to be replaced there, we just need to remove the -drive test cases.
This in turn allows some simplification of the code.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The spec does not justify clearing of any E1000_ICR_OTHER_CAUSES when
E1000_ICR_OTHER is set in EIAC. In fact, removing this code fixes the
issue the Linux driver runs into since 4aea7a5c5e94 ("e1000e: Avoid
receiver overrun interrupt bursts") and was worked around by
745d0bd3af99 ("e1000e: Remove Other from EIAC").
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We banned use of certain g_assert_FOO() functions outside tests, and
made checkpatch.pl flag them (commit 6e9389563e). We neglected to
purge existing uses. Do that now.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180608170231.27912-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: John Snow <jsnow@redhat.com>
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
-----BEGIN PGP SIGNATURE-----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=g3bP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.0-20180612' into staging
ppc patch queue 2018-06-12
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
# gpg: Signature made Tue 12 Jun 2018 07:43:21 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180612: (33 commits)
spapr_pci: Remove unhelpful pagesize warning
xics_kvm: use KVM helpers
ppc/pnv: fix LPC HC firmware address space
spapr: handle cpu core unplug via hotplug handler chain
spapr: handle pc-dimm unplug via hotplug handler chain
spapr: introduce machine unplug handler
spapr: move memory hotplug support check into spapr_memory_pre_plug()
spapr: move lookup of the node into spapr_memory_plug()
spapr: no need to verify the node
target/ppc: Allow PIR read in privileged mode
ppc4xx_i2c: Clean up and improve error logging
target/ppc: extend eieio for POWER9
mos6522: convert VMSTATE_TIMER_PTR_TEST to VMSTATE_TIMER_PTR
mos6522: move timer frequency initialisation to mos6522_reset
cuda: embed mos6522_cuda device directly rather than using QOM object link
mos6522: fix vmstate_mos6522_timer version in vmstate_mos6522
ppc: add missing FW_CFG_PPC_NVRAM_FLAT definition
ppc: remove obsolete macio_init() definition from mac.h
ppc: remove obsolete pci_pmac_init() definitions from mac.h
hw/misc/mos6522: Add trailing '\n' to qemu_log() calls
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CID 1390604
If the initiator sends a packet with TYPE_DATA set without
initiating a CMD_GET_OBJECT_INFO first, then usb_mtp_get_data
can trip on a null s->data_out.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <jpgr2m8ajfk.fsf_-_@linux.bootlegged.copy>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
qbus_create_inplace() creates a new reference in realize(), it must be
released in unrealize().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
A link property can be set during creation, with
object_property_add_link() and later with object_property_set_link().
add_link() doesn't add a reference to the target object, while
set_link() does.
Furthemore, OBJ_PROP_LINK_UNREF_ON_RELEASE flags, set during add_link,
says whether a reference must be released when the property is destroyed.
This can lead to leaks if the property was later set_link(), as the
added reference is never released.
Instead, rename OBJ_PROP_LINK_UNREF_ON_RELEASE to OBJ_PROP_LINK_STRONG
and use that has an indication on how the link handle reference
management in set_link().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Cédric Le Goater