1. Convert bytes in BlkAioEmAIOCB:
aio->bytes is only passed to already int64_t interfaces, and set in
blk_aio_prwv, which is updated here.
2. For all updated functions the parameter type becomes wider so callers
are safe.
3. In blk_aio_prwv we only store bytes to BlkAioEmAIOCB, which is
updated here.
4. Other updated functions are wrappers on blk_aio_prwv.
Note that blk_aio_preadv and blk_aio_pwritev become safer: before this
commit, it's theoretically possible to pass qiov with size exceeding
INT_MAX, which than converted to int argument of blk_aio_prwv. Now it's
converted to int64_t which is a lot better. Still add assertions.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211006131718.214235-11-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: tweak assertion and grammar]
Signed-off-by: Eric Blake <eblake@redhat.com>
Function is updated so that parameter type becomes wider, so all
callers should be OK with it.
Look at blk_co_copy_range() itself: bytes is passed only to
blk_check_byte_request() and bdrv_co_copy_range(), which already have
int64_t bytes parameter, so we are OK.
Note that requests exceeding INT_MAX are still restricted by
blk_check_byte_request().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211006131718.214235-10-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
Convert blk_pdiscard, blk_pwrite_compressed, blk_pwrite_zeroes.
These are just wrappers for functions with int64_t argument, so allow
passing int64_t as well. Parameter type becomes wider so all callers
should be OK with it.
Note that requests exceeding INT_MAX are still restricted by
blk_check_byte_request().
Note also that we don't (and are not going to) convert blk_pwrite and
blk_pread: these functions return number of bytes on success, so to
update them, we should change return type to int64_t as well, which
will lead to investigating and updating all callers which is too much.
So, blk_pread and blk_pwrite remain unchanged.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211006131718.214235-9-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
We updated blk_do_pdiscard() and its wrapper blk_co_pdiscard(). Both
functions are updated so that the parameter type becomes wider, so all
callers should be OK with it.
Look at blk_do_pdiscard(): bytes is passed only to
blk_check_byte_request() and bdrv_co_pdiscard(), which already have
int64_t bytes parameter, so we are OK.
Note that requests exceeding INT_MAX are still restricted by
blk_check_byte_request().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211006131718.214235-5-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
We convert blk_do_pwritev_part() and some wrappers:
blk_co_pwritev_part(), blk_co_pwritev(), blk_co_pwrite_zeroes().
All functions are converted so that the parameter type becomes wider, so
all callers should be OK with it.
Look at blk_do_pwritev_part() body:
bytes is passed to:
- trace_blk_co_pwritev (we update it here)
- blk_check_byte_request, throttle_group_co_io_limits_intercept,
bdrv_co_pwritev_part - all already have int64_t argument.
Note that requests exceeding INT_MAX are still restricted by
blk_check_byte_request().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211006131718.214235-4-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
For both updated functions, the type of bytes becomes wider, so all callers
should be OK with it.
blk_co_preadv() only passes its arguments to blk_do_preadv().
blk_do_preadv() passes bytes to:
- trace_blk_co_preadv, which is updated too
- blk_check_byte_request, throttle_group_co_io_limits_intercept,
bdrv_co_preadv, which are already int64_t.
Note that requests exceeding INT_MAX are still restricted by
blk_check_byte_request().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20211006131718.214235-3-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
Linux limits the size of iovecs to 1024 (UIO_MAXIOV in the kernel
sources, IOV_MAX in POSIX). Because of this, on some host adapters
requests with many iovecs are rejected with -EINVAL by the
io_submit() or readv()/writev() system calls.
In fact, the same limit applies to SG_IO as well. To fix both the
EINVAL and the possible performance issues from using fewer iovecs
than allowed by Linux (some HBAs have max_segments as low as 128),
introduce a separate entry in BlockLimits to hold the max_segments
value from sysfs. This new limit is used only for SG_IO and clamped
to bs->bl.max_iov anyway, just like max_hw_transfer is clamped to
bs->bl.max_transfer.
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Cc: Hanna Reitz <hreitz@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Cc: qemu-stable@nongnu.org
Fixes: 18473467d5 ("file-posix: try BLKSECTGET on block devices too, do not round to power of 2", 2021-06-25)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210923130436.1187591-1-pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add function to change bs inside blk.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20210824083856.17408-3-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
For block host devices, I/O can happen through either the kernel file
descriptor I/O system calls (preadv/pwritev, io_submit, io_uring)
or the SCSI passthrough ioctl SG_IO.
In the latter case, the size of each transfer can be limited by the
HBA, while for file descriptor I/O the kernel is able to split and
merge I/O in smaller pieces as needed. Applying the HBA limits to
file descriptor I/O results in more system calls and suboptimal
performance, so this patch splits the max_transfer limit in two:
max_transfer remains valid and is used in general, while max_hw_transfer
is limited to the maximum hardware size. max_hw_transfer can then be
included by the scsi-generic driver in the block limits page, to ensure
that the stricter hardware limit is used.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow block backends to poll their devices/users to check if they have
been quiesced when entering a drained section.
This will be used in the next patch to wait for the NBD server to be
completely quiesced.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20210602060552.17433-2-slp@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Two callers of BlockDriver.bdrv_make_empty() remain that should not call
this method directly. Both do not have access to a BdrvChild, but they
can use a BlockBackend, so we add this function that lets them use it.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200429141126.85159-4-mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are several callers that need to create a new block backend from
an existing BDS; make the task slightly easier with a common helper
routine.
Suggested-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200424190903.522087-2-eblake@redhat.com>
[mreitz: Set @ret only in error paths, see
https://lists.nongnu.org/archive/html/qemu-block/2020-04/msg01216.html]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200428192648.749066-2-eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Now that node level interface bdrv_truncate() supports passing request
flags to the block driver, expose this on the BlockBackend level, too.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20200424125448.63318-4-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
External callers of blk_co_*() and of the synchronous blk_*() functions
don't currently increase the BlockBackend.in_flight counter, but calls
from blk_aio_*() do, so there is an inconsistency whether the counter
has been increased or not.
This patch moves the actual operations to static functions that can
later know they will always be called with in_flight increased exactly
once, even for external callers using the blk_co_*() coroutine
interfaces.
If the public blk_co_*() interface is unused, remove it.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200407121259.21350-3-kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We have two drivers (iscsi and file-posix) that (in some cases) return
success from their .bdrv_co_truncate() implementation if the block
device is larger than the requested offset, but cannot be shrunk. Some
callers do not want that behavior, so this patch adds a new parameter
that they can use to turn off that behavior.
This patch just adds the parameter and lets the block/io.c and
block/block-backend.c functions pass it around. All other callers
always pass false and none of the implementations evaluate it, so that
this patch does not change existing behavior. Future patches take care
of that.
Suggested-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20190918095144.955-5-mreitz@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add blk write function with qiov_offset parameter. It's needed for the
following commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20191011090711.19940-4-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
This fixes devices like IDE that can still start new requests from I/O
handlers in the CPU thread while the block backend is drained.
The basic assumption is that in a drain section, no new requests should
be allowed through a BlockBackend (blk_drained_begin/end don't exist,
we get drain sections only on the node level). However, there are two
special cases where requests should not be queued:
1. Block jobs: We already make sure that block jobs are paused in a
drain section, so they won't start new requests. However, if the
drain_begin is called on the job's BlockBackend first, it can happen
that we deadlock because the job stays busy until it reaches a pause
point - which it can't if its requests aren't processed any more.
The proper solution here would be to make all requests through the
job's filter node instead of using a BlockBackend. For now, just
disabling request queuing on the job BlockBackend is simpler.
2. In test cases where making requests through bdrv_* would be
cumbersome because we'd need a BdrvChild. As we already got the
functionality to disable request queuing from 1., use it in tests,
too, for convenience.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
The functionality offered by blk_pread_unthrottled() goes back to commit
498e386c58. Then, we couldn't perform I/O throttling with synchronous
requests because timers wouldn't be executed in polling loops. So the
commit automatically disabled I/O throttling as soon as a synchronous
request was issued.
However, for geometry detection during disk initialisation, we always
used (and still use) synchronous requests even if guest requests use AIO
later. Geometry detection was not wanted to disable I/O throttling, so
bdrv_pread_unthrottled() was introduced which disabled throttling only
temporarily.
All of this isn't necessary any more because we do run timers in polling
loop and even synchronous requests are now using coroutine
infrastructure internally. For this reason, commit 90c78624f already
removed the automatic disabling of I/O throttling.
It's time to get rid of the workaround for the removed code, and its
abuse of blk_root_drained_begin()/end(), as well.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This adds a new parameter to blk_new() which requires its callers to
declare from which AioContext this BlockBackend is going to be used (or
the locks of which AioContext need to be taken anyway).
The given context is only stored and kept up to date when changing
AioContexts. Actually applying the stored AioContext to the root node
is saved for another commit.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add an Error parameter to blk_set_aio_context() and use
bdrv_child_try_set_aio_context() internally to check whether all
involved nodes can actually support the AioContext switch.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Some users (like block jobs) can tolerate an AioContext change for their
BlockBackend. Add a function that tells the BlockBackend that it can
allow changes.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The next patch needs access to a device's minimum permitted
alignment, since NBD wants to advertise this to clients. Add
an accessor function, borrowing from blk_get_max_transfer()
for accessing a backend's block limits.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20190329042750.14704-6-eblake@redhat.com>
For some users of BlockBackends, just increasing the in_flight counter
is easier than implementing separate handlers in BlockDevOps. Make the
helper functions for this public.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The last user of blk_attach_dev_legacy() was the code in xen_disk which
has recently been reworked. Now there is no user for this legacy function
anymore. Thus we can finally remove all code related to the "legacy_dev"
flag, too, and turn the related "void *" in block-backend.c into proper
"DeviceState *" to fix some of the remaining TODOs there.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add a new command, returning block nodes (and their users) graph.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20181221170909.25584-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Pass read flags and write flags separately. This is needed to handle
coming BDRV_REQ_NO_SERIALISING clearly in following patches.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It's a BlockBackend wrapper of the BDS interface.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601092648.24614-10-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Allow block driver to map and unmap a buffer for later I/O, as a performance
hint.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20180116060901.17413-5-famz@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
This commit eliminates the 1:1 relationship between BlockBackend and
throttle group state. Users will be able to create multiple throttle
nodes, each with its own throttle group state, in the future. The
throttle group state cannot be per-BlockBackend anymore, it must be
per-throttle node. This is done by gathering ThrottleGroup membership
details from BlockBackendPublic into ThrottleGroupMember and refactoring
existing code to use the structure.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These two conditions corresponds to mirror job's source and target,
which need to be allowed as they are part of the non-shared storage
migration workflow: failing to inactivate either will result in a
failure during migration completion.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <20170823134242.12080-3-famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
[eblake: improve comment grammar]
Signed-off-by: Eric Blake <eblake@redhat.com>
blk_truncate() itself will pass that value to bdrv_truncate(), and all
callers of blk_truncate() just set the parameter to PREALLOC_MODE_OFF
for now.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170613202107.10125-4-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Change the 'int count' parameter in *pwrite_zeros, *pdiscard related
functions (and some others) to 'int bytes', as they both refer to bytes.
This helps with code legibility.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Message-id: 20170609101808.13506-1-el13635@mail.ntua.gr
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Another possibility is to use tg->lock, which we're holding anyway in
both schedule_next_request and throttle_group_co_io_limits_intercept.
This would require open-coding the CoQueue however, so I've chosen this
alternative.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170605123908.18777-10-pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
For one thing, this allows us to drop the error message generation from
qemu-img.c and blockdev.c and instead have it unified in
bdrv_truncate().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20170328205129.15138-3-mreitz@redhat.com
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
blk_name() is not modifying data passed to it through pointer and it
returns also a pointer to const so the argument can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Allow block backends to forward drain requests to their devices/users.
The initial intended purpose for this patch is to allow BBs to forward
requests along to BlockJobs, which will want to pause if their associated
BB has entered a drained region.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 20170316212351.13797-3-jsnow@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
The HMP command 'qemu-io' is a bit tricky because it wants to work on
the original BlockBackend, but additional permissions could be required.
The details are explained in a comment in the code, but in summary, just
request whatever permissions the current qemu-io command needs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Some devices allow a media change between read-only and read-write
media. They need to adapt the permissions in their .change_media_cb()
implementation, which can fail. So add an Error parameter to the
function.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Now that blk_insert_bs() requests the BlockBackend permissions for the
node it attaches to, it can fail. Instead of aborting, pass the errors
to the callers.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
We want every user to be specific about the permissions it needs, so
we'll pass the initial permissions as parameters to blk_new(). A user
only needs to call blk_set_perm() if it wants to change the permissions
after the fact.
The permissions are stored in the BlockBackend and applied whenever a
BlockDriverState should be attached in blk_insert_bs().
This does not include actually choosing the right set of permissions
everywhere yet. Instead, the usual FIXME comment is added to each place
and will be addressed in individual patches.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
The BlockBackend can now store the permissions that its user requires.
This is necessary because nodes can be ejected from or inserted into a
BlockBackend and all of these operations must make sure that the user
still gets what it requested initially.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Acked-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170213135235.12274-19-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
All read/write functions already have a single coroutine-based function
on the BlockBackend level through which all requests go (no matter what
API style the external caller used) and which passes the requests down
to the block node level.
This patch exports a bdrv_co_ioctl() function and uses it to extend this
mode of operation to ioctls.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Almost all block devices are qdevified by now. This allows us to go back
from the BlockBackend to the DeviceState. xen_disk is the last device
that is missing. We'll remember in the BlockBackend if a xen_disk is
attached and can then disable any features that require going from a BB
to the DeviceState.
While at it, clearly mark the function used by xen_disk as legacy even
in its name, not just in TODO comments.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
