We were previously implementing INV (like INVALL) to just blow away
cached highest-priority-pending-LPI information on all connected
redistributors. For GICv4.0, this isn't going to be sufficient,
because the LPI we are invalidating cached information for might be
either physical or virtual, and the required action is different for
those two cases. So we need to do the full process of looking up the
ITE from the devid and eventid. This also means we can do the error
checks that the spec lists for this command.
Split out INV handling into a process_inv() function like our other
command-processing functions. For the moment, stick to handling only
physical LPIs; we will add the vLPI parts later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-19-peter.maydell@linaro.org
For GICv4, interrupt table entries read by process_its_cmd() may
indicate virtual LPIs which are to be directly injected into a VM.
Implement the ITS side of the code for handling this. This is
similar to the existing handling of physical LPIs, but instead of
looking up a collection ID in a collection table, we look up a vPEID
in a vPE table. As with the physical LPIs, we leave the rest of the
work to code in the redistributor device.
The redistributor half will be implemented in a later commit;
for now we just provide a stub function which does nothing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-15-peter.maydell@linaro.org
We use the common function gicv3_idreg() to supply the CoreSight ID
register values for the GICv3 for the copies of these ID registers in
the distributor, redistributor and ITS register frames. This isn't
quite correct, because while most of the register values are the
same, the PIDR0 value should vary to indicate which of these three
frames it is. (You can see this and also the correct values of these
PIDR0 registers by looking at the GIC-600 or GIC-700 TRMs, for
example.)
Make gicv3_idreg() take an extra argument for the PIDR0 value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220408141550.1271295-5-peter.maydell@linaro.org
Implement the ITS MOVI command. This command specifies a (physical) LPI
by DeviceID and EventID and provides a new ICID for it. The ITS must
find the interrupt translation table entry for the LPI, which will
tell it the old ICID. It then moves the pending state of the LPI from
the old redistributor to the new one and updates the ICID field in
the translation table entry.
This is another GICv3 ITS command that we forgot to implement. Linux
does use this one, but only if the guest powers off one of its CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220122182444.724087-15-peter.maydell@linaro.org
Implement the ITS MOVALL command, which takes all the pending
interrupts on a source redistributor and makes the not-pending on
that source redistributor and pending on a destination redistributor.
This is a GICv3 ITS command which we forgot to implement. (It is
not used by Linux guests.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220122182444.724087-14-peter.maydell@linaro.org
The ITS-related parts of the redistributor code make some checks for
whether registers like GICR_PROPBASER and GICR_PENDBASER are zero.
There is no requirement in the specification for treating zeroes in
these address registers specially -- they contain guest physical
addresses and it is entirely valid (if unusual) for the guest to
choose to put the tables they address at guest physical address zero.
We use these values only to calculate guest addresses, and attempts
by the guest to use a bad address will be handled by the
address_space_* functions which we use to do the loads and stores.
Remove the unnecessary checks.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220122182444.724087-9-peter.maydell@linaro.org
Quoting Peter Maydell:
"These MEMTX_* aren't from the memory transaction
API functions; they're just being used by gicd_readl() and
friends as a way to indicate a success/failure so that the
actual MemoryRegionOps read/write fns like gicv3_dist_read()
can log a guest error."
We are going to introduce more MemTxResult bits, so it is
safer to check for !MEMTX_OK rather than MEMTX_ERROR.
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The logic of gicv3_redist_update() is as follows:
* it must be called in any code path that changes the state of
(only) redistributor interrupts
* if it finds a redistributor interrupt that is (now) higher
priority than the previous highest-priority pending interrupt,
then this must be the new highest-priority pending interrupt
* if it does *not* find a better redistributor interrupt, then:
- if the previous state was "no interrupts pending" then
the new state is still "no interrupts pending"
- if the previous best interrupt was not a redistributor
interrupt then that remains the best interrupt
- if the previous best interrupt *was* a redistributor interrupt,
then the new best interrupt must be some non-redistributor
interrupt, but we don't know which so must do a full scan
In commit 17fb5e36aa we effectively added the LPI interrupts
as a kind of "redistributor interrupt" for this purpose, by adding
cs->hpplpi to the set of things that gicv3_redist_update() considers
before it gives up and decides to do a full scan of distributor
interrupts. However we didn't quite get this right:
* the condition check for "was the previous best interrupt a
redistributor interrupt" must be updated to include LPIs
in what it considers to be redistributor interrupts
* every code path which updates the LPI state which
gicv3_redist_update() checks must also call gicv3_redist_update():
this is cs->hpplpi and the GICR_CTLR ENABLE_LPIS bit
This commit fixes this by:
* correcting the test on cs->hppi.irq in gicv3_redist_update()
* making gicv3_redist_update_lpi() always call gicv3_redist_update()
* introducing a new gicv3_redist_update_lpi_only() for the one
callsite (the post-load hook) which must not call
gicv3_redist_update()
* making gicv3_redist_lpi_pending() always call gicv3_redist_update(),
either directly or via gicv3_redist_update_lpi()
* removing a couple of now-unnecessary calls to gicv3_redist_update()
from some callers of those two functions
* calling gicv3_redist_update() when the GICR_CTLR ENABLE_LPIS
bit is cleared
(This means that the not-file-local gicv3_redist_* LPI related
functions now all take care of the updates of internally cached
GICv3 information, in the same way the older functions
gicv3_redist_set_irq() and gicv3_redist_send_sgi() do.)
The visible effect of this bug was that when the guest acknowledged
an LPI by reading ICC_IAR1_EL1, we marked it as not pending in the
LPI data structure but still left it in cs->hppi so we would offer it
to the guest again. In particular for setups using an emulated GICv3
and ITS and using devices which use LPIs (ie PCI devices) a Linux
guest would complain "irq 54: nobody cared" and then hang. (The hang
was intermittent, presumably depending on the timing between
different interrupts arriving and being completed.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20211124202005.989935-1-peter.maydell@linaro.org
Our GICv3 QOM interface includes an array property
redist-region-count which allows board models to specify that the
registributor registers are not in a single contiguous range, but
split into multiple pieces. We implemented this for KVM, but
currently the TCG GICv3 model insists that there is only one region.
You can see the limit being hit with a setup like:
qemu-system-aarch64 -machine virt,gic-version=3 -smp 124
Add support for split regions to the TCG GICv3. To do this we switch
from allocating a simple array of MemoryRegions to an array of
GICv3RedistRegion structs so that we can use the GICv3RedistRegion as
the opaque pointer in the MemoryRegion read/write callbacks. Each
GICv3RedistRegion contains the MemoryRegion, a backpointer allowing
the read/write callback to get hold of the GICv3State, and an index
which allows us to calculate which CPU's redistributor is being
accessed.
Note that arm_gicv3_kvm always passes in NULL as the ops argument
to gicv3_init_irqs_and_mmio(), so the only MemoryRegion read/write
callbacks we need to update to handle this new scheme are the
gicv3_redist_read/write functions used by the emulated GICv3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implemented lpi processing at redistributor to get lpi config info
from lpi configuration table,determine priority,set pending state in
lpi pending table and forward the lpi to cpuif.Added logic to invoke
redistributor lpi processing with translated LPI which set/clear LPI
from ITS device as part of ITS INT,CLEAR,DISCARD command and
GITS_TRANSLATER processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-7-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added properties to enable ITS feature and define qemu system
address space memory in gicv3 common,setup distributor and
redistributor registers to indicate LPI support.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-6-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a space in the message printed when gicr_read*/gicr_write* returns
MEMTX_ERROR in arm_gicv3_redist.c.
Signed-off-by: Rebecca Cran <rebecca@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210706211432.31902-1-rebecca@nuviainc.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GIC ID registers cover an area 0x30 bytes in size
(12 registers, 4 bytes each). We were incorrectly decoding
only the first 0x20 bytes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524124248.28394-2-peter.maydell@linaro.org
When either GICD_IPRIORITYR or GICR_IPRIORITYR is read as a 32-bit
register, the post left-shift operator in the for loop causes an
extra shift after the least significant byte has been placed.
The 32-bit value actually returned is therefore the expected value
shifted left by 8 bits.
Signed-off-by: Amol Surati <suratiamol@gmail.com>
Message-id: 20180614054857.26248-1-suratiamol@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv3 specification says that reserved register addresses
should RAZ/WI. This means we need to return MEMTX_OK, not MEMTX_ERROR,
because now that we support generating external aborts the
latter will cause an abort on new board models.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Coverity complains that the GICR_IPRIORITYR case in gicv3_readl()
can overflow an array, because it doesn't know that the offsets
passed to that function must be word aligned. Add some assert()s
which hopefully tell Coverity that this isn't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1468261372-17508-1-git-send-email-peter.maydell@linaro.org
Fix missing includes of qemu/log.h, which broke compilation with the
simple trace backend (the default backend pulls in log.h implicitly
via trace.h).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Tested-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Message-id: 1466416634-9798-1-git-send-email-peter.maydell@linaro.org
Implement the registers in the GICv3 CPU interface which generate
new SGI interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-18-git-send-email-peter.maydell@linaro.org
Implement the code which updates the GIC state when an interrupt
input into the GIC is asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-15-git-send-email-peter.maydell@linaro.org
Implement the redistributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-13-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
